Análise paramétrica do método de injeção alternada de água e CO2(WAG) em reservatórios de petróleo

After the decline of production from natural energy of the reservoir, the methods of enhanced oil recovery, which methods result from the application of special processes such as chemical injection, miscible gases, thermal and others can be applied. The advanced recovery method with alternating - CO2 injection WAG uses the injection of water and gas, normally miscible that will come in contact with the stock oil. In Brazil with the discovery of pre-salt layer that gas gained prominence. The amount of CO2 present in the oil produced in the pre-salt layer, as well as some reservoirs is one of the challenges to be overcome in relation to sustainable production once this gas needs to be processed in some way. Many targets for CO2 are proposed by researchers to describe some alternatives to the use of CO2 gas produced such as enhanced recovery, storage depleted fields, salt caverns storage and marketing of CO2 even in plants. The largest oil discoveries in Brazil have recently been made by Petrobras in the pre -salt layer located between the states of Santa Catarina and Espírito Santo, where he met large volumes of light oil with a density of approximately 28 ° API, low acidity and low sulfur content. This oil that has a large amount of dissolved CO2 and thus a pioneering solution for the fate of this gas comes with an advanced recovery. The objective of this research is to analyze which parameters had the greatest influence on the enhanced recovery process. The simulations were performed using the "GEM" module of the Computer Modelling Group, with the aim of studying the advanced recovery method in question. For this work, semi - synthetic models were used with reservoir and fluid data that can be extrapolated to practical situations in the Brazilian Northeast. The results showed the influence of the alternating injection of water and gas on the recovery factor and flow rate of oil production process, when compared to primary recovery and continuous water injection or continuous gas injection

Recuperação avançada de óleos pesados em poços fraturados utilizando aquecimento eletromagnético indutivo

The success achieved by thermal methods of recovery, in heavy oils, prompted the emergence of studies on the use of electromagnetic waves as heat generating sources in oil reservoirs. Thus, this generation is achieved by three types of different processes according to the frequency range used. They are: the electromagnetic induction heating, the resistive and the dielectric, also known as radiation. This study was based on computer simulations in oil reservoirs with characteristics similar to those found in the sedimentary basins of the Brazilian Northeast. All cases studied were simulated using the software STARS, CMG (Computer Group, version 2012.10 Modeling). Some simulations took into account the inclusion of electrically sensitive particles in certain sectors of the reservoir model studied by fracturing. The purpose of this work is the use of the electromagnetic induction heating as a recovery method of heavy oil, to check the influence of these aforementioned particles on the reservoir model used. Comparative analyses were made involving electromagnetic induction heating, the operation of hydraulic fracturing and the injection of water to the different situations of the reservoir model studied. It was found that fracturing the injection well in order that the electromagnetic heating occurs in the same well where there is water injection, there was a considerable increase in the recovery factor and in the cumulative oil production in relation to the models in which hydraulic fracturing occurred in the production well and water injection in the injection well. This is due to the generation of steam in situ in the reservoir.

Produção de hidrogénio através da gasificação da biomassa

A procura de uma forma limpa de combustível, aliada à crescente instabilidade de preços dos combustíveis fósseis verificada nos mercados faz com que o hidrogénio se torne num combustível a considerar devido a não resultar qualquer produto poluente da sua queima e de se poder utilizar, por exemplo, desperdícios florestais cujo valor de mercado não está inflacionado por não pertencer à cadeia alimentar humana. Este trabalho tem como objetivo simular o processo de gasificação de biomassa para produção de hidrogénio utilizando um gasificador de leito fluidizado circulante. O oxigénio e vapor de água funcionam como agentes gasificantes. Para o efeito usou-se o simulador de processos químicos ASPEN Plus. A simulação desenvolvida compreende três etapas que ocorrem no interior do gasificador: pirólise, que foi simulada por um bloco RYIELD, combustão de parte dos compostos voláteis, simulada por um bloco RSTOIC e, por fim, as reações de oxidação e gasificação do carbonizado “char”, simuladas por um bloco RPLUG. Os valores de rendimento dos compostos após a pirólise, obtidos por uma correlação proposta por Gomez-Barea, et al. (2010), foram os seguintes: 20,33% “char”, 22,59% alcatrão, 36,90% monóxido de carbono, 16,05%m/m dióxido de carbono, 3,33% metano e 0,79% hidrogénio (% em massa). Como não foi possível encontrar valores da variação da composição do gás à saída do gasificador com a variação da temperatura, para o caso de vapor de água e oxigénio, optou-se por utilizar apenas vapor na simulação de forma a comparar os seus valores com os da literatura. Às temperaturas de 700, 770 e 820ºC, para um “steam-to-biomass ratio”, (SBR) igual a 0,5, os valores da percentagem molar de monóxido de carbono foram, respetivamente, 56,60%, 55,84% e 53,85%, os valores de hidrogénio foram, respetivamente, 17,83%, 18,25% e 19,31%, os valores de dióxido de carbono foram, respetivamente, 16,40%, 16,85% e 17,93% e os valores de metano foram, respetivamente, 9,00%, 8,95% e 8,83%. Os valores da composição à saída do gasificador, à temperatura de 820ºC, para um SBR de 0,5 foram: 53,85% de monóxido de carbono, 19,31% de hidrogénio, 17,93% de dióxido de carbono e 8,83% de metano (% em moles). Para um SBR de 0,7 a composição à saída foi de 54,45% de monóxido de carbono, 19,01% de hidrogénio, 17,59% de dióxido de carbono e 8,87% de metano. Por fim, quando SBR foi igual a 1 a composição do gás à saída foi de 55,08% de monóxido de carbono, 18,69% de hidrogénio, 17,24% de dióxido de carbono e 8,90% de metano. Os valores da composição obtidos através da simulação, para uma mistura de ar e vapor de água, ER igual a 0,26 e SBR igual a 1, foram: 34,00% de monóxido de carbono, 14,65% de hidrogénio, 45,81% de dióxido de carbono e 5,41% de metano. A simulação permitiu-nos ainda dimensionar o gasificador e determinar alguns parâmetros hidrodinâmicos do gasificador, considerando que a reação “water-gas shift” era a limitante, e que se pretendia obter uma conversão de 95%. A velocidade de operação do gasificador foi de 4,7m/s e a sua altura igual a 0,73m, para um diâmetro de 0,20m.

Aplicação de β-glicosidases produzidas pelos microorganismos Aureobasidium pullulans e Thermoascus aurantiacus ao processo fermentativo da aguardente de cana com foco na produção de terpenos

Pós-graduação em Alimentos e Nutrição - FCFAR

Aplicações de Ferramentas Lean em uma Indústria de Transformação de Papel

Esta dissertação foi desenvolvida no âmbito do 2º ano do Mestrado em Engenharia Mecânica – Ramo de Gestão Industrial no Instituto Superior de Engenharia do Porto. Este projeto realizou-se em ambiente industrial, nomeadamente na Tubembal, S.A. uma empresa localizada no concelho da Trofa, distrito do Porto. Esta empresa dedica-se à transformação de papel e comércio de embalagens, produz tubos e cantoneiras de cartão e é atualmente a maior empresa do sector na Península Ibérica. Esta dissertação baseia-se na aplicação de ferramentas Lean, numa perspetiva de melhoria de um ambiente produtivo industrial, melhorando o desempenho dos processos existentes e consequentemente a produtividade da empresa em estudo, com o objetivo de a tornar mais competitiva num ambiente global. A metodologia Lean tem como principal objetivo a eliminação de desperdício em toda a cadeia de valor e neste sentido surge como fundamental numa cultura de melhoria contínua e focalização no cliente, que se pretende instalar nesta empresa. Foi realizada uma análise profunda a toda a cadeia de valor como forma de identificar os maiores desperdícios e posteriormente apresentadas medidas para combater estes mesmos desperdícios, podendo assim reduzir custos. No projeto de melhoria apresentado à organização constam como principais ações, a implementação da metodologia 5S’s como ferramenta essencial para mudança de hábitos dos funcionários e integração e envolvimento de todos num mesmo projeto comum, na busca da melhoria contínua. Procedeu-se ainda à simulação de algumas propostas de reorganização do layout de forma a encontrar aquela que minimizasse os custos com movimentações e garantisse um fluxo controlado e em segurança dos produtos e pessoas dentro da fábrica. As propostas apresentadas mostram que a reorganização do layout da fábrica pode trazer ganhos significativos para a empresa, redução direta no tempo perdido em deslocações e maior disponibilidade dos meios e consequente direta redução dos custos. Todas as propostas apresentadas visam a adaptação da empresa a um modelo mais dinâmico de negócio, capaz de responder rápida e eficazmente aos seus clientes, adaptando-se ao mercado e garantindo a sua sustentabilidade num futuro próximo.

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Estudo do processo de drenagem gravitacional do óleo assistido com injeção de vapor e solvente

Como os recursos de hidrocarbonetos convencionais estão se esgotando, a crescente demanda mundial por energia impulsiona a indústria do petróleo para desenvolver mais reservatórios não convencionais. Os recursos mundiais de betume e óleo pesado são estimados em 5,6 trilhões de barris, dos quais 80% estão localizados na Venezuela, Canadá e EUA. Um dos métodos para explorar estes hidrocarbonetos é o processo de drenagem gravitacional assistido com injeção de vapor e solvente (ES-SAGD Expanding Solvent Steam Assisted Gravity Drainage). Neste processo são utilizados dois poços horizontais paralelos e situados verticalmente um acima do outro, um produtor na base do reservatório e um injetor de vapor e solvente no topo do reservatório. Este processo é composto por um método térmico (injeção de vapor) e um método miscível (injeção de solvente) com a finalidade de causar a redução das tensões interfaciais e da viscosidade do óleo ou betume. O objetivo deste estudo é analisar a sensibilidade de alguns parâmetros operacionais, tais como: tipo de solvente injetado, qualidade do vapor, distância vertical entre os poços, porcentagem de solvente injetado e vazão de injeção de vapor sobre o fator de recuperação para 5, 10 e 15 anos. Os estudos foram realizados através de simulações concretizadas no módulo STARS (Steam Thermal, and Advanced Processes Reservoir Simulator) do programa da CMG (Computer Modelling Group), versão 2010.10, onde as interações entre os parâmetros operacionais, estudados em um modelo homogêneo com características de reservatórios semelhantes aos encontrados no Nordeste Brasileiro, foram observadas. Os resultados obtidos neste estudo mostraram que os melhores fatores de recuperação ocorreram para níveis máximos do percentual de solvente injetado e da distância vertical entre os poços. Observou-se também que o processo será rentável dependendo do tipo e do valor do solvente injetado

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Estudo paramétrico da injeção de vapor em reservatórios delgados

Exploration of heavy oil reservoirs is increasing every year in worldwide, because the discovery of light oil reservoirs is becoming increasingly rare. This fact has stimulated the research with the purpose of becoming viable, technically and economically, the exploration of such oil reserves. In Brazil, in special in the Northeast region, there is a large amount of heavy oil reservoir, where the recovery by the so called secondary methods Water injection or gas injection is inefficient or even impracticable in some reservoirs with high viscosity oils (heavy oils). In this scenario, steam injection appears as an interesting alternative for recover of these kinds of oil reservoirs. Its main mechanism consists of oil viscosity reduction through steam injection, increasing reservoir temperature. This work presents a parametric simulation study of some operational and reservoir variables that had influence on oil recovery in thin reservoirs typically found in Brazilian Northeast Basins, that use the steam injection as improved oil recovery method. To carry out simulations, it was used the commercial software STARS (Steam, Thermal, and Advanced Processes Reservoir Simulator) from CMG (Computer Modeling Group) version 2007.11. Reservoirs variables studied were horizontal permeability, vertical and horizontal permeability ratio, water zone and pay zone thickness ratio, pay zone thickness and thermal conductivity of the rock. Whereas, operational parameters studied were distance between wells and steam injection rate. Results showed that reservoir variables that had more influence on oil recovery were horizontal permeability and water zone and pay zone thickness ratio. In relation to operational variables, results showed that short distances between wells and low steam injection rates improved oil recovery

Estudo do processo de drenagem gravitacional do óleo assistido com injeção de vapor e solvente

Como os recursos de hidrocarbonetos convencionais estão se esgotando, a crescente demanda mundial por energia impulsiona a indústria do petróleo para desenvolver mais reservatórios não convencionais. Os recursos mundiais de betume e óleo pesado são estimados em 5,6 trilhões de barris, dos quais 80% estão localizados na Venezuela, Canadá e EUA. Um dos métodos para explorar estes hidrocarbonetos é o processo de drenagem gravitacional assistido com injeção de vapor e solvente (ES-SAGD Expanding Solvent Steam Assisted Gravity Drainage). Neste processo são utilizados dois poços horizontais paralelos e situados verticalmente um acima do outro, um produtor na base do reservatório e um injetor de vapor e solvente no topo do reservatório. Este processo é composto por um método térmico (injeção de vapor) e um método miscível (injeção de solvente) com a finalidade de causar a redução das tensões interfaciais e da viscosidade do óleo ou betume. O objetivo deste estudo é analisar a sensibilidade de alguns parâmetros operacionais, tais como: tipo de solvente injetado, qualidade do vapor, distância vertical entre os poços, porcentagem de solvente injetado e vazão de injeção de vapor sobre o fator de recuperação para 5, 10 e 15 anos. Os estudos foram realizados através de simulações concretizadas no módulo STARS (Steam Thermal, and Advanced Processes Reservoir Simulator) do programa da CMG (Computer Modelling Group), versão 2010.10, onde as interações entre os parâmetros operacionais, estudados em um modelo homogêneo com características de reservatórios semelhantes aos encontrados no Nordeste Brasileiro, foram observadas. Os resultados obtidos neste estudo mostraram que os melhores fatores de recuperação ocorreram para níveis máximos do percentual de solvente injetado e da distância vertical entre os poços. Observou-se também que o processo será rentável dependendo do tipo e do valor do solvente injetado

Otimização de vazão de poços injetores em projeto de injeção de água utilizando simulação por linhas de fluxo

Until the early 90s, the simulation of fluid flow in oil reservoir basically used the numerical technique of finite differences. Since then, there was a big development in simulation technology based on streamlines, so that nowadays it is being used in several cases and it can represent the physical mechanisms that influence the fluid flow, such as compressibility, capillarity and gravitational segregation. Streamline-based flow simulation is a tool that can help enough in waterflood project management, because it provides important information not available through traditional simulation of finite differences and shows, in a direct way, the influence between injector well and producer well. This work presents the application of a methodology published in literature for optimizing water injection projects in modeling of a Brazilian Potiguar Basin reservoir that has a large number of wells. This methodology considers changes of injection well rates over time, based on information available through streamline simulation. This methodology reduces injection rates in wells of lower efficiency and increases injection rates in more efficient wells. In the proposed model, the methodology was effective. The optimized alternatives presented higher oil recovery associated with a lower water injection volume. This shows better efficiency and, consequently, reduction in costs. Considering the wide use of the water injection in oil fields, the positive outcome of the modeling is important, because it shows a case study of increasing of oil recovery achieved simply through better distribution of water injection rates

Estudo comparativo da utilização do nitrogênio como fluido alternativo após a injeção de vapor

Currently, due to part of world is focalized to petroleum, many researches with this theme have been advanced to make possible the production into reservoirs which were classified as unviable. Because of geological and operational challenges presented to oil recovery, more and more efficient methods which are economically successful have been searched. In this background, steam flood is in evidence mainly when it is combined with other procedures to purpose low costs and high recovery factors. This work utilized nitrogen as an alternative fluid after steam flood to adjust the best combination of alternation between these fluids in terms of time and rate injection. To describe the simplified economic profile, many analysis based on liquid cumulative production were performed. The completion interval and injection fluid rates were fixed and the oil viscosity was ranged at 300 cP, 1.000 cP and 3.000 cP. The results defined, for each viscosity, one specific model indicating the best period to stop the introduction of steam and insertion of nitrogen, when the first injected fluid reached its economic limit. Simulations in physics model defined from one-eighth nine-spot inverted were realized using the commercial simulator Steam, Thermal and Advanced Processes Reservoir Simulator STARS of Computer Modelling Group CMG

Incorporação de resíduo cerâmico para prevenção da retrogressão da resistência de cimentos de poços de petróleo submetidos à injeção de vapor

Steam injection is the most used thermal recovery method of oil nowadays because of the high degree of development of the technique that allows high recovery factors. However, injection of superheated steam into the reservoir affects the entire structure of the well, including the cemented layer that presents a retrogression of compressive strength and increases the permeability due to formation of more crystalline and denser phases at temperatures above 110 °C. These changes result in failures in the cement that favor the entrance of formation fluids into the annulus space resulting in unsafe operations and restrictions in the economic life of the well. But the strength retrogression can be prevented by partial replacement of cement by silica-based materials that reduce the CaO/SiO2 ratio of cement slurries changing the trajectory of the reactions, converting those deleterious phases in phases with satisfactory mechanical strength and permeability. The aim of this study was to evaluate the behavior of a ceramic waste material rich in silica in partial and total substitution of a mineral additive used to fight the strength retrogression of cement slurries subjected to high temperatures. The evaluation was made by compression, X-ray diffraction (XRD) and thermogravimetry (TG/DTG). The samples were submitted to a cycle of low temperature (38 °C) for 28 days and a cycle of low temperature followed by exposure to 280 ºC and 1000 psi by 3 days. The results showed that slurries with additions of up to 30% of the waste material are not enough to prevent the strength retrogression, while slurries with additions of the waste material combined with silica flour in various proportions produced hydrated products of low Ca/Si ratios that maintained the compressive strength at satisfactory levels

Estudo da perda de carga e calor no poço injetor no processo De drenagem gravitacional assistida por vapor (SAGD)

The oil companies in the area in general are looking for new technologies that can increase the recovery factor of oil contained in reservoirs. These investments are mainly aimed at reducing the costs of projects which are high. Steam injection is one of these special methods of recovery in which steam is injected into the reservoir in order to reduce the viscosity of the oil and make it more mobile. The process assisted gravity drainage steam (SAGD) using steam injection in its mechanism, as well as two parallel horizontal wells. In this process steam is injected through the horizontal injection well, then a vapor chamber is formed by heating the oil in the reservoir and, by the action of gravitational forces, this oil is drained down to where the production well. This study aims to analyze the influence of pressure drop and heat along the injection well in the SAGD process. Numerical simulations were performed using the thermal simulator STARS of CMG (Computer Modeling Group). The parameters studied were the thermal conductivity of the formation, the flow of steam injection, the inner diameter of the column, the steam quality and temperature. A factorial design was used to verify the influence of the parameters studied in the recovery factor. We also analyzed different injection flow rates for the model with pressure drop and no pressure drop, as well as different maximum flow rates of oil production. Finally, we performed an economic analysis of the two models in order to check the profitability of the projects studied. The results showed that the pressure drop in injection well have a significant influence on the SAGD process.