Controle automático para injeção otimizada de gás em poços de petróleo equipados para funcionamento com gás lift contínuo

The continuous gas lift method is the main artificial lifting method used in the oil industry for submarine wells, due to its robustness and the large range of flow rate that the well might operate. Nowadays, there is a huge amount of wells producing under this mechanism. This method of elevation has a slow dynamics due to the transients and a correlation between the injected gas rate and the of produced oil rate. Electronics controllers have been used to adjust many parameters of the oil wells and also to improve the efficiency of the gas lift injection system. This paper presents a intelligent control system applied to continuous gas injection in wells, based in production s rules, that has the target of keeping the wells producing during the maximum period of time, in its best operational condition, and doing automatically all necessary adjustments when occurs some disturbance in the system. The author also describes the application of the intelligent control system as a tool to control the flow pressure in the botton of the well (Pwf). In this case, the control system actuates in the surface control valve

Análise de confiabilidade de uma bomba centrífuga: aplicação na injeção de água para recuperação de petróleo

The oil industry`s need to produce with maximum efficiency, not to mention the safety and the environment aspects, encourages the optimization of processes. It makes them look for a level of excellence in acquisition of equipment, ensuring the quality without prejudice security of facilities and peoples. Knowing the reliability of equipment and that this stands for a system is fundamental to the production strategy to seeks the maximum return on investment. The reliability analysis techniques have been increasingly applied in the industry as strategy for predicting failures likelihood ensuring the integrity of processes. Some reliability theories underlie the decisions to use stochastic calculations to estimate equipment failure. This dissertation proposes two techniques associating qualitative (through expertise opinion) and quantitative data (European North Sea oil companies fault database, Ored) applied on centrifugal pump to water injection system for secondary oil recovery on two scenarios. The data were processed in reliability commercial software. As a result of hybridization, it was possible to determine the pump life cycle and what impact on production if it fails. The technique guides the best maintenance policy - important tool for strategic decisions on asset management.

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Estudo do comportamento da pluma de benzeno em fase dissolvida na água subterrânea sob a influência do sistema de remediação integrado: injeção de ar e extração de vapores do solo, no município de Cubatão - SP

Pós-graduação em Geociências e Meio Ambiente - IGCE

Efeitos cardiovasculares e na ingestão de NaCl e água induzida pela injeção de trans-4-aminocrotonic acid (TACA) no núcleo parabraquial lateral (NPBL) de ratos

Pós-graduação em Ciências Fisiológicas - FOA

Controle da injeção de potências ativa e reativa em inversor de Geração Distribuída conectado à rede de distribuição em corrente alternada em baixa tensão, empregando LMIs com realimentação de estados e critérios de D-estabilidade

Pós-graduação em Engenharia Elétrica - FEIS

Efeitos da injeção de 3 amino 1,2,4 triazole (ATZ), inibidor da catalase, na área septal medial na ingestão de água e na excreção renal de água e eletrólitos induzidos pela estimulação colinérgica também da área septal medial

A área septal medial (ASM), situada no prosencéfalo, está envolvida na regulação cardiovascular e no controle do balanço hidroeletrolítico. Esta área é rica em receptores colinérgicos e a ativação dos mesmos induz ingestão de água, natriurese e anti-diurese. Existem evidências experimentais de que as espécies reativas de oxigênio possam participar do controle de respostas fisiológicas. Resultados recentes de nosso laboratório demonstraram que uma espécie reativa de oxigênio, o peróxido de hidrogênio (H2O2), injetada na ASM reduz a ingestão de água induzida por carbacol (agonista colinérgico) também injetado na ASM. No presente projeto propomos estudar os efeitos do aumento da produção endógena de H2O2 na ASM nos efeitos dipsogênico, natriurético e anti-diurético do carbacol injetado na ASM. O inibidor da catalase, 3 amino 1,2,4 triazole (ATZ) será injetado na ASM para aumentar os níveis endógenos de H2O2

Influência da vermiculita expandida na formulação de pastas leves para evitar a migração de gás em cimentação de poços petrolíferos

The gas migration during the cementing of wells is one of the main problems of oil wells engineering. Its occurrence can cause severe problems since shortly to loss of control of the well after cementation. Recently, 20/04/2010 In an accident of major proportions in the Gulf of Mexico, among other factors, faulty cementing operation provided the gas migration, causing the accident, in which 11 people died and 17 were injured occurred. Besides the serious consequences that can be caused by gas migration, remediation of the problem, which is made by injecting cement in damaged areas, usually involves additional costs and is not always effective. Therefore, preventing gas migration to be preferred. Some methods are used to prevent the migration of the pressurized gas as the annular space, application of pressure pulses, reducing the height of the cement column compressible cement pastes of low permeability, pastes and to control free filtered water, and binders of thixotropic cement expandable and flexible. Thus, the cement pastes used to prevent gas migration must meet the maximum these methods. Thus, this study aimed to formulate a cement paste to prevent gas migration, using the expanded vermiculite, and evaluate the behavior of the folder trials necessary for use in oil wells. Free water content, rheological properties, compressive strength, loss of liquid phase sedimentation of solids, specific weight, thickening time and gas migration: The following tests were performed. The results show that meets the specifications paste formulated for use in oil wells and the use of expanded vermiculite contribute to the absorption of free water, thixotropy and low density. The absorption of free water is proven to result in zero percentage test free water content, thixotropy is observed with the high value of the initial gel strength (Gi) in testing rheological properties and low density is proven in test weight specific

Otimização de vazão de poços injetores em projeto de injeção de água utilizando simulação por linhas de fluxo

Until the early 90s, the simulation of fluid flow in oil reservoir basically used the numerical technique of finite differences. Since then, there was a big development in simulation technology based on streamlines, so that nowadays it is being used in several cases and it can represent the physical mechanisms that influence the fluid flow, such as compressibility, capillarity and gravitational segregation. Streamline-based flow simulation is a tool that can help enough in waterflood project management, because it provides important information not available through traditional simulation of finite differences and shows, in a direct way, the influence between injector well and producer well. This work presents the application of a methodology published in literature for optimizing water injection projects in modeling of a Brazilian Potiguar Basin reservoir that has a large number of wells. This methodology considers changes of injection well rates over time, based on information available through streamline simulation. This methodology reduces injection rates in wells of lower efficiency and increases injection rates in more efficient wells. In the proposed model, the methodology was effective. The optimized alternatives presented higher oil recovery associated with a lower water injection volume. This shows better efficiency and, consequently, reduction in costs. Considering the wide use of the water injection in oil fields, the positive outcome of the modeling is important, because it shows a case study of increasing of oil recovery achieved simply through better distribution of water injection rates

Estudo paramétrico da recuperação de óleo no processo de drenagem gravitacional com injeção de CO2

The gas injection has become the most important IOR process in the United States. Furthermore, the year 2006 marks the first time the gas injection IOR production has surpassed that of steam injection. In Brazil, the installation of a petrochemical complex in the Northeast of Brazil (Bahia State) offers opportunities for the injection of gases in the fields located in the Recôncavo Basin. Field-scale gas injection applications have almost always been associated with design and operational difficulties. The mobility ratio, which controls the volumetric sweep, between the injected gas and displaced oil bank in gas processes, is typically unfavorable due to the relatively low viscosity of the injected gas. Furthermore, the difference between their densities results in severe gravity segregation of fluids in the reservoirs, consequently leading to poor control in the volumetric sweep. Nowadays, from the above applications of gas injection, the WAG process is most popular. However, in attempting to solve the mobility problems, the WAG process gives rise to other problems associated with increased water saturation in the reservoir including diminished gas injectivity and increased competition to the flow of oil. The low field performance of WAG floods with oil recoveries in the range of 5-10% is a clear indication of these problems. In order to find na effective alternative to WAG, the Gas Assisted Gravity Drainage (GAGD) was developed. This process is designed to take advantage of gravity force to allow vertical segregation between the injected CO2 and reservoir crude oil due to their density difference. This process consists of placing horizontal producers near the bottom of the pay zone and injecting gás through existing vertical wells in field. Homogeneous models were used in this work which can be extrapolated to commercial application for fields located in the Northeast of Brazil. The simulations were performed in a CMG simulator, the STARS 2007.11, where some parameters and their interactions were analyzed. The results have shown that the CO2 injection in GAGD process increased significantly the rate and the final recovery of oil

Estudo comparativo da injeção de água usando poços verticais e horizontais

Oil recovery using waterflooding has been until now the worldwide most applied method, specially for light oil recovery, its success is mainly because of the low costs involved and the facilities of the injection process. The Toe- To-Heel Waterflooding TTHWTM method uses a well pattern of vertical injector wells completed at the bottom of the reservoir and horizontal producer wells completed at the top of it. The main producing mechanism is gravitational segregation in short distance. This method has been studied since the early 90´s and it had been applied in Canada with positive results for light heavy oils, nevertheless it hasn´t been used in Brazil yet. In order to verify the applicability of the process in Brazil, a simulation study for light oil was performed using Brazilian northwest reservoirs characteristics. The simulations were fulfilled using the STARS module of the Computer Modelling Group Software, used to perform improved oil recovery studies. The results obtained in this research showed that the TTHWTM well pattern presented a light improvement in terms of recovery factor when compared to the conventional 5- Spot pattern, however, it showed lower results in the economic evaluation

Monitoramento microbiológico e físico-químico de tanques de armazenamento de óleo e água

A injeção da água do mar nos campos marítimos (offshore), processo este conhecido como recuperação secundária de petróleo, gera muitos resíduos e efluentes. Dentre estes, pode-se destacar a água produzida, que consiste de água de formação, água naturalmente presente na formação geológica do reservatório de petróleo, e água de injeção, aquela normalmente injetada no reservatório para aumento de produção. Sete tanques de armazenamento de água/óleo de um terminal foram monitorados quanto à presença de micro-organismos e teores de sulfato, sulfeto, pH e condutividade. Particularmente, as bactérias redutoras de sulfato (BRS), que agem às expensas da atividade de outras espécies, reduzindo sulfato à sulfeto, constituindo-se num problema-chave. Os tanques de óleo codificados como Verde, Ciano, Roxo, Cinza, Vermelho, Amarelo e Azul, apresentaram comportamentos distintos quanto aos parâmetros microbiológicos e físico-químicos. Após este monitoramento, de acordo com valores referência adotados, e levando-se em conta como principais parâmetros classificatórios concentrações de BRS, bactérias anaeróbias totais e sulfeto, os dois tanques considerados mais limpos do monitoramento foram os tanques roxo e ciano. Analogamente, por apresentarem os piores desempenhos frente aos três principais parâmetros, os tanques amarelo e cinza foram considerados os mais sujos de todo o monitoramento. Após esta segregação, esses três principais parâmetros, mais a concentração de sulfato, foram inter-relacionados a fim de se corroborar esta classificação. Foi possível observar que o sulfeto instantâneo não foi o parâmetro mais adequado para se avaliar o potencial metabólico de uma amostra. Por este motivo, foram verificados os perfis metabólicos das BRS presentes nas amostras, confirmando a segregação dos tanques, baseada em parâmetros em batelada

Produção biogênica de sulfetos em amostras de água e óleo

Durante a exploração de petróleo offshore (fora da costa), a injeção de água do mar no processo de recuperação secundária de petróleo, ocasiona a produção de sulfeto de hidrogênio (H2S) pela presença das bactérias redutoras de sulfato (BRS), que reduzem o sulfato presente na água em sulfeto. A produção intensiva de H2S tem sido um dos maiores problemas das indústrias petrolíferas, pois constitui-se uma das principais causas de corrosão em linhas de produção (tubulações), equipamentos e tanques metálicos. Os principais micro-organismos presentes em amostras salinas provenientes de tanques de armazenamento de água e óleo da indústria do petróleo são as bactérias anaeróbias heterotróficas totais (BANHT) e as bactérias redutoras de sulfato (BRS). Atualmente, a quantificação desses grupos microbianos é realizada através da técnica do Número Mais Provável (NMP) que estima o resultado em aproximadamente 28 dias. Neste trabalho foi utilizada a metodologia de produção semi-contínua de sulfetos biogênicos por 15 dias, numa tentativa de correlacionar com os resultados de quantificação de BANHT e BRS através da técnica convencional do NMP. Nesse caso, avaliou-se as condições mais adequadas para a produção biogênica de sulfetos em tanques, alterando-se parâmetros tais como salinidade, temperatura e composição do meio de cultura. Verificou-se que os aumentos da salinidade e da temperatura do meio implicaram na diminuição da atividade biogênica semi-contínua de geração de sulfetos. E conforme dilui-se o meio de cultura, o crescimento de bactérias foi reduzido, assim como a geração de sulfetos. A quantificação de BRS e BANHT foi avaliada pela técnica do NMP de acordo com o método do FDA em 2011 e de Harrigan em 1998. Este último subestima a população microbiana, desconsiderando os limites e erros provenientes da técnica

Remediação de solos e lençóis freáticos em postos de gasolina via processo de fenton: estudo de caso

Alguns cientistas ambientais prevêem que a poluição dos solos será um dos maiores legados com grandes impactos para as gerações futuras, pois atualmente ainda existe desconhecimento das fontes poluidoras e da sua extensão. O Brasil, devido a sua extensão territorial, suas bacias hidrográficas, número de postos de abastecimentos e controles ambientais ainda ineficazes, está muito exposto a esse tipo de poluição. Atualmente, há no Brasil mais de 34.300 postos de combustíveis, com volume de 65.000.000 m3 de gasolina e diesel consumidos anualmente, conforme dados da Agência Nacional do Petróleo Gás Natural e Biocombustíveis , ANP, em 2008. Sendo assim, a exposição e contaminação dos solos e dos lençóis freáticos com constituintes aromáticos do diesel e gasolina torna-se um sério problema ambiental. Dentro deste grupo, encontram-se o benzeno, tolueno, xileno, conhecido como BTEX e os hidrocarbonetos policíclicos aromáticos, conhecido como PAH. Este trabalho tem como objetivo estudar a remediação in-situ de um posto de combustíveis na região do ABC Paulista, no Estado de São Paulo. Aplicando-se a técnica de Processo Oxidativo Avançado via reagente de Fenton (H2O2 + Fe2+ → Fe3+ + OH- + OH . ), o radical hidroxila gerado mineraliza compostos aromáticos, decompondo-os definitivamente. Amostras de água do posto em estudo apresentavam elevados teores de BTEX e PAH, 2,58 mg.L-1 e 0,298 mg.L-1 respectivamente, estando em níveis não tolerados pelo órgão ambiental paulista CETESB sendo necessária a intervenção para tratamento da área. Com os níveis de poluentes e o perfil hidrogeológico identificados, a remediação foi iniciada com injeções no solo de peróxido de hidrogênio a 8%v.v, FeSO4 a 0,40 mg.L-1 e solução à base de NPK (nitrogênio, fósforo e nitrogênio) a 100 mg.L-1 como nutrientes para os microorganismos do solo. Estes valores são provenientes de experimentos anteriores e tratamentos já realizados. Foram conduzidas campanhas de injeção trimestrais com 100 litros desta solução completa como reagente , e medições trimestrais de BTEX, PAH e outros parâmetros de controle, que foram indicando o sucesso do tratamento. Após 18 meses o local foi considerado tratado pelo órgão ambiental, onde monitoramentos semestrais estão em continuidade para garantir o resultado do tratamento e das ações corretivas. Assim, o estudo real da remediação de solos contaminados com os poluentes orgânicos via processo de Fenton, com concentração de H2O2 a 8%v/v, e FeSO4 a 0,40 mg.L-1 demonstrou-se uma técnica de sucesso. O entendimento dos resultados da remediação, mesmo sujeitos aos fenômenos naturais, como intempéries e chuvas, é uma experiência grande, pois por mais reais que simulações em laboratório possam ser, é muito difícil incluir nestes sistemas, as variações que um tratamento real está exposto