Corrosão de vários materiais metálicos em álcool etílico hidratado combustível e sua inibição a 25 graus C

Estudou-se o comportamento à corrosão de diversos materiais metálicos como aço, cobre, latão e pares galvânicos (aço-latão) em álcool etilico combustível (91.1 - 93.9 -INPM) adicionado de várias substâncias a fim de avaliar possíveis efeitos inibidores ou aceleradores da corrosão. Foi verificado a influência na corrosão, de ion cloreto, acetato de sódio, ácido benzóico, trietanolamina, butinodiol e um inibidor comercial. O acetato de sódio seguido do produto comercial se revelaram os melhores aditivos sob o ponto de vista da inibição da corrosão. A adição de cloreto, como um possível contaminante foi estudada e obteve-se um aumento bastante grande na taxa de corrosão. A adição de perclorato de potássio ao álcool combustível normalmente utilizado para aumentar a condutividade da solução nos ensaios eletroquímicos, mostrou ser prejudicial por modificar apreciavelmente as características do comportamento à corrosão dos materiais ensaiados, aumentando-a ou diminuindo-a conforme o caso.

Obtenção e caracterização de dióxido de estanho nanoestruturado pelo método de síntese contínua por combustão em solução

Continuous Synthesis by Solution Combustion was employed in this work aiming to obtain tin dioxide nanostructured. Basically, a precursor solution is prepared and then be atomized and sprayed into the flame, where its combustion occurs, leading to the formation of particles. This is a recent technique that shows an enormous potential in oxides deposition, mainly by the low cost of equipment and precursors employed. The tin dioxide (SnO2) nanostructured has been widely used in various applications, especially as gas sensors and varistors. In the case of sensors based on semiconducting ceramics, where surface reactions are responsible for the detection of gases, the importance of surface area and particle size is even greater. The preference for a nanostructured material is based on its significant increase in surface area compared to conventional microcrystalline powders and small particle size, which may benefit certain properties such as high electrical conductivity, high thermal stability, mechanical and chemical. In this work, were employed as precursor solution tin chloride dehydrate diluted in anhydrous ethyl alcohol. Were utilized molar ratio chloride/solvent of 0,75 with the purpose of investigate its influence in the microstructure of produced powder. The solution precursor flux was 3 mL/min. Analysis with X-ray diffraction appointed that a solution precursor with molar ratio chloride/solvent of 0,75 leads to crystalline powder with single phase and all peaks are attributed to phase SnO2. Parameters as distance from the flame with atomizer distance from the capture system with the pilot, molar ratio and solution flux doesn t affect the presence of tin dioxide in the produced powder. In the characterization of the obtained powder techniques were used as thermogravimetric (TGA) and thermodiferential analysis (DTA), particle size by laser diffraction (GDL), crystallographic analysis by X-ray diffraction (XRD), morphology by scanning electron microscopy (SEM), transmission electron microscopy (TEM), specific surface area (BET) and electrical conductivity analysis. The techniques used revealed that the SnO2 exhibits behavior of a semiconductor material, and a potentially promising material for application as varistor and sensor systems for gas

UTILIZAÇÃO da PRÓPOLIS E ÁLCOOL ETÍLICO NO CONTROLE DE Salmonella em RAÇÕES AVÍCOLAS

Em quatro experimentos foram avaliados como agentes antibacterianos os produtos própolis em solução alcoólica e álcool etílico, adicionados às rações artificialmente contaminadas com os respectivos sorotipos: Salmonella typhimurium Nalr - Specr, (resistentes ao ácido Nalidíxico e a Spectinomicina) nos três primeiros experimentos e Salmonella agona Nalr - Specr, Salmonella infantis Nalr - Specr e Salmonella enteritidis Nalr - Specr no quarto experimento. As rações foram fornecidas a grupos de 10-16 pintos de corte de um dia. em todos os experimentos os produtos testados foram adicionados na base de 2% da ração. Quando se utilizou solução hidroalcóolica de própolis (exp. 1), seguidas 120 horas após o desafio, detectou-se a presença da bactéria nos cecos. No segundo experimento, testou-se a solução de própolis e seu diluente, o álcool etílico; seguidas 96 horas após o desafio, não foi observada a presença da bactéria nos cecos (< 2,0 log10). Avaliou-se, no terceiro experimento, a ação da solução de própolis e do álcool etílico no tempo, adicionados na ração 14 dias e 28 dias antes do fornecimento às aves. Após 72 horas do desafio, a leitura nas placas acusou a presença da bactéria nos cecos. Dentro deste último período, também se avaliou a ação da própolis em pó (extrato seco) e esse mesmo extrato em uma solução aquosa, adicionados à ração 48 horas antes do fornecimento às aves sendo que os resultados confirmaram a presença da bactéria nos cecos. No quarto experimento avaliou-se somente o álcool etílico nas rações artificialmente contaminadas com os sorotipos S. agona, S. enteritidis e S. infantis, registrando-se contagem zero (<2,0 log10) apenas com o último sorotipo. Os resultados obtidos permitem concluir que o tratamento com a solução de própolis apresentou ação sobre a S. typhimurium somente quando em solução alcóolica, dentro de um período de 48 horas, indicando que o efeito bactericida se deveu ao álcool etílico presente na solução. A ação do tratamento com o álcool etílico sobre os demais sorotipos demonstrou resultado parcial sendo observado efeito bactericida nos sorotipos S. typhimurium e S. enteritidis artificialmente inoculados na ração.

Extração, caracterização e aplicação do corante de urucum (Bixa orellana L.) no tingimento de fibras naturais

The increasing demand for natural dyes in place of synthetic ones is justified by the non-toxicity or low toxicity of the former. The synthetic dyes are associated with diseases like cancer as well as when released in the environment takes longer to degrade and the intermediates could be still more toxic. The Annatto (Bixa Orellana L.) is a carotenoid and one of the more important natural dyes used in the food industry. In the form of dye, it represents nearly 70% of the world natural dye production and 90% in Brazil. In the present work, annatto seeds were used of the species peruana paulista, which had nearly 2.1% of bixin. The process of dye extraction with ethyl alcohol showed 4% of dye in the form of powder with particle diameter of 28mm. The extraction process did not alter the chemical composition of the dye, which was confirmed by the electronic spectrum of absorption. Dyeings were carried out with different mordents to study the total colour difference as well as the wash fastness properties and friction fastness properties under wet and dry conditions. The samples treated with copper sulphate showed colour difference but at the same time showed better fastness results. The samples treated with resin (no formaldehyde) did not alter the colour significantly still better the fastness properties. From the results, it could be stated that the resin could be an alternative for heavy metallic mordents

Contribution to the laboratory diagnosis of human cryptosporidiosis

A criptosporidiose humana é uma infecção causada pelo Cryptosporidium sp, um protozoário coccídio de patogenicidade emergente e responsável por severa e prostrante diarréia aquosa em humanos, principalmente em indivíduos imunodeprimidos. O diagnóstico, feito através da utilização de esfregaços de fezes submetidos a técnicas de concentração e coloração específica pela fucsina-carbólica tem oferecido bons resultados em nosso laboratório. Tendo em vista o longo tempo despendido para a observação dos esfregaços considerando-se a pequenez das formas e o contraste da coloração, realizamos modificações no procedimento técnico da coloração ácido-resistente que resultaram em sensível melhoria das preparações: a fucsina-carbólica passou a ser deixada sobre o esfregaço por período de 3 minutos (LENNETTE et al., 1985) e procedeu-se a substituição da solução de álcool-ácido sulfúrico a 5% (HENRIKSEN & POHLENZ, 1981) por solução de ácido clorídrico a 0,5% em álcool etílico 70%, por cerca de 2 minutos (contribuição original). Estas alterações promoveram melhor remoção do excesso de fucsina-carbólica, aumentando a eficiência da etapa de descoloração e consequentemente otimizando o contraste do processo de coloração. Nestas condições, as lâminas examinadas em microscópio óptico em aumentos de 250x e 1000x tiveram a visualização dos oocistos do protozoário facilitada, sendo os mesmos observados em contraste destacado com pigmentação intensa de cor rosa-avermelhada contra coloração de fundo azulada. Vale destacar que estas modificações oferecem vantagens de rápido processamento do material e facilidade de visualização do protozoário, diminuindo o tempo de microscopia, tornando a análise das lâminas mais rápida e menos cansativa, agilizando o diagnóstico.

Aspectos dinâmicos da água versus álcool e acetona por técnicas de congelamento

Water still represents, on its critical properties and phase transitions, a problem of current scientific interest, as a consequence of the countless open questions and of the inadequacy of the existent theoretical models, mainly related to the different solid and liquid phases that this substance possesses. For example, there are 13 known crystalline forms of water, and also amorphous phases. One of them, the amorphous ice of very high density (VHDA), was just recently observed. Other example is the anomalous behavior in the macroscopic density, which presents a maximum at the temperature of 277 K. In order to experimentally investigate the behavior of one of the liquid-solid phase transitions, the anomaly in its density and also the metastability, we used three different cooling techniques and, as comparison systems, we made use of the solvents: acetone and ethyl alcohol. The first studied cooling system employ a Peltier plate, a device recently developed, which makes use of small cubes made up of semiconductors to change heat among two surfaces; the second system is a commercial refrigerator, similar to the residential ones. Finally, the liquid nitrogen technique, which is used to refrigerate the samples in a container, in two ways: a very fast and other one, almost static. In those three systems, three Beckers of aluminum were used (with a volume of 80 ml, each), containing water, alcohol and acetone. They were closed and maintained at atmospheric pressure. Inside of each Becker were installed three thermocouples, disposed along the vertical axis of the Beckers, one close to the inferior surface, other to the medium level and the last one close the superior surface. A system of data acquisition was built via virtual instrumentation using as a central equipment a Data-Acquisition board. The temperature data were collected by the three thermocouples in the three Beckers, simultaneously, in function of freezing time. We will present the behavior of temperature versus freezing time for the three substances. The results show the characterization of the transitions of the liquid

Determination of ecological efficiency in internal combustion engines: The use of biodiesel

This paper evaluates and quantifies the environmental impact from the use of some renewable fuels and fossils fuels in internal combustion engines. The following fuels are evaluated: gasoline blended with anhydrous ethyl alcohol (anhydrous ethanol), conventional diesel fuel, biodiesel in pure form and blended with diesel fuel, and natural gas. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. The ecological efficiency concept depends on the environmental impact caused by CO(2), SO(2), NO(x) and particulate material (PM) emissions. The exhaust gases from internal combustion engines, in the case of the gasoline (blended with alcohol), biodiesel and biodiesel blended with conventional diesel, are the less polluting; on the other hand, the most polluting are those related to conventional diesel. They can cause serious problems to the environment because of their dangerous components for the human, animal and vegetable life. The resultant pollution of each one of the mentioned fuels are analyzed, considering separately CO(2), SO(2), NO(x) and particulate material (PM) emissions. As conclusion, it is possible to calculate an environmental factor that represents, qualitatively and quantitative, the emissions in internal combustion engines that are mostly used in urban transport. Biodiesel in pure form (B100) and blended with conventional diesel as fuel for engines pollute less than conventional diesel fuel. The ecological efficiency for pure biodiesel (B100) is 86.75%: for biodiesel blended with conventional diesel fuel (B20, 20% biodiesel and 80% diesel), it is 78.79%. Finally, the ecological efficiency for conventional diesel, when used in engines, is 77.34%; for gasoline, it is 82.52%, and for natural gas, it is 91.95%. All these figures considered a thermal efficiency of 30% for the internal combustion engine. Crown Copyright (C) 2008 Published by Elsevier Ltd. All rights reserved.

Biodiesel CO2 emissions: A comparison with the main fuels in the Brazilian market

The use of biodiesel is increasing as an attractive fuel due to the depleting fossil fuel resources and environmental degradation. This paper presents results of an investigation on the potentials of biodiesel as an alternative fuel and main substitute of diesel oil, comparing the CO2 emissions of the main fuels in the Brazilian market with those of biodiesel, in pure form or blended in different proportions with diesel oil (2%, 5%, and 20%, called B2, B5, and B20, respectively). The results of the study are shown in ton CO2 per m(3) and ton CO2 per year of fuel. The fuels were analyzed considering their chemical composition, stoichiometric combustion parameters and mean consumption for a single vehicle. The fuels studied were: gasoline, diesel oil, anhydrous ethyl alcohol (anhydrous ethanol), and biodiesel from used frying oil and from soybean oil. For the case of biodiesel, its complete life cycle and the closed carbon cycle (photosynthesis) were considered. With data provided by the Brazilian Association of Automotive Vehicle Manufacturers (ANFAVEA) for the number of vehicles produced in Brazil, the emissions of CO2 for the national fleet in 2007 were obtained per type of fuel. With data provided by the Brazilian Department of Transit (DENATRAN) concerning the number of diesel vehicles in the last five years in Brazil, the total CO2 emissions and the percentage that they would decrease in the case of use of pure biodiesel, B100, or several mixtures, B2, B5 and B20, were calculated. Estimates of CO2 emissions for a future scenario considering the mixtures B5 and B20 are also included in this article. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Obtenção e aplicação de sistemas microemulsionados na recuperação avançada de petróleo

Due to the need of increasing production in reservoirs that are going through production decline, methods of advanced recovery have frequently been used in the last years, as the use of conventional methods has not been successful in solving the problem of oil drifting. In this work, the efficiency of different microemulsionated systems in the flow of oil from cores from Assu and Botucatu formations. Regarding drifting tests, cores were calcinated at a temperature of 1000°C, for 18 hours, with the aim of eliminating any organic compound present in it, increasing the resultant permeability. Following, the cores were isolated with resin, resulting in test specimens with the following dimensions: 3.8 cm of diameter and 8.7 cm of length. Cores were saturated with brine, composed of aqueous 2 wt % KCl, and oil from Guamaré treatment station (Petrobras/RN). A pressure of 20 psi was used in all tests. After core saturation, brine was injected again, followed by oil at constant flow rate. The system S3 - surfactant (anionic surfactant of short chain), isoamillic alcohol, pine oil, and water - presented the best drift efficiency, 81.18%, while the system S1E commercial surfactant, ethyl alcohol, pine oil, and distilled water presented low drift efficiency, 44,68%

Uso de antibióticos para o controle de bactérias endógenas visando à micropropagação da figueira

A descontaminação dos explantes é um dos princípios básicos para o sucesso da cultura de tecidos. Um dos problemas diagnosticados na propagação in vitro da figueira, através de gemas apicais, é a contaminação endógena dos explantes por bactérias. Este trabalho teve como objetivo avaliar a eficiência de alguns antibióticos em meio de cultura para o controle de bactérias endógenas em gemas apicais de figueira. Foram avaliados os seguintes tratamentos: T1(sem adição de antibiótico); T2 (30 mg L-1 de cloranfenicol); T3 (250 mg L-1 de ampicilina sódica); T4 (500 mg L-1 de ácido nalidícico); T5 (150 mg L-1 de cefalotina sódica); T6 (500 mg L-1 de tetraciclina), e T7 (400 mg L-1 de norfloxacina). Após coletados em campo, os segmentos de ramos contendo as gemas foram colocados em recipiente com água corrente. Posteriormente, as gemas apicais foram imersas em álcool etílico a 70% e hipoclorito de sódio a 2,5%. Todo procedimento de desinfestação externa dos explantes foi realizado em câmara de fluxo laminar. Os explantes foram inoculados em tubos de ensaio contendo 15 mL de meio básico MS suplementado, após a autoclavagem, com as doses de antibióticos de acordo com os tratamentos estabelecidos. Após a inoculação, os explantes foram mantidos em sala de crescimento por quatro dias no escuro e, em seguida, sob fotoperíodo de 16 horas de luz branca fria e irradiância de 25 µmol m s-1, na temperatura de 22 ± 3ºC. A assepsia realizada externamente nos explantes foi suficiente para o controle de contaminação fúngica, e a adição de antibióticos ao meio, após autoclavagem, foi eficiente para o controle de bactérias endógenas, cujo antibiótico ampicilina sódica proporcionou mais de 90% de explantes sobreviventes.

Bee Visitors of Quaresmeira Flowers (Tibouchina granulosa Cogn.) in the Region of Dourados (MS-Brasil)

This research was developed in the center-urban area at the city of Dourados (MS), in Tibouchina granulosa trees, a plant popularly known as quaresmeira in Brazil. The floral visitors of this species were recorded in three daily periods: 7 - 8 a.m., 1 - 2 p.m. and 4 - 5 p. m. Bee visitors of those plants were collected with an entomological net when they landed on the flowers. The bees were anesthetized in a closed camera containing etila acetate, conserved in Dietrich ' s fixative and, soon afterwards, transferred to 70% ethyl alcohol for subsequent identification. Almost 300 specimens of Africanized Apis mellifera, Trigona spinipes and Tetragonisca angustula were collected. The presence of these three species of bees in the flowers of T. granulosa suggests that they can be considered the main floral visitors of that vegetal species. T. angustula workers did not visit the flowers of T. granulosa between 7 and 8 a.m., but they were the main floral visitors from 4 to 5 p.m. The workers of T. spinipes presented a very aggressive behavior against the Africanized A. mellifera workers on the quaresmeira flowers, defending the food sources with strength and efficiency and provoking a drastic reduction in the number of honeybee visits between 1 and 2 p.m. Nevertheless, they did not interfere in the opportunistic activity of foraging by T. angustula workers, mainly between 4 and 5 p.m. The most important result of this research was the detection of the Competitive Exclusion Principle between A. mellifera and T. spinipes species in relation to the foraging behavior, when they exploit the floral resources of T. granulosa.

Composição centesimal, potencial antioxidante e perfil dos ácidos graxos de sementes de jambolão (Syzygium cumini L.)

The aim of this work was to characterize jambolan seeds regarding its centesimal composition, and also to evaluate its antioxidant potential and fatty acid profile. To obtain the extract, dehydrated and grinded seeds were extracted with ethyl alcohol for 30 minutes, at a proportion of 1:3 of seeds:ethyl alcohol, under continuous agitation, at room temperature. Afterwards, the mixture was filtered and the supernatant subjected to a rotoevaporator at 40 degrees C aiming to determine, by direct weighing, the extract's dry matter yield. According to the results of centesimal composition, higher values were found for total carbohydrates. Ethanolic extract from jambolan seeds exhibited antioxidant potential, given by the EC(50) value, as well as by the amount of total phenolic compounds. In the oil studied, higher percentage of unsatured fatty acids stood out, being linoleic acid the main component, considered an essential fatty acid.

Estudo da enxertia hipocotiledonar do maracujazeiro-amarelo sobre dois porta-enxertos, através de microscopia eletrônica de varredura

O objetivo deste trabalho foi verificar quanto tempo após a realização da enxertia hipocotiledonar ocorre a soldadura ou adesão entre enxerto e porta-enxerto, e também a formação da ponte de calo, verificada pelo total preenchimento da fenda por tecido meristemático secundário (calo). Foram produzidas 56 mudas de maracujazeiro-amarelo (Passiflora edulis Sims f. flavicarpa Deg.) pela enxertia hipocotiledonar em fenda cheia no topo sobre dois porta-enxertos (P. edulis Sims f. flavicarpa Deg. e P. alata Dryander). Aos 0, 3, 6, 9, 12, 15 e 18 dias após a enxertia, coletou-se a região da enxertia de quatro mudas de cada combinação. O material coletado foi fixado em solução de glutaraldeído a 3%, pós-fixado em tetróxido de ósmio a 2%, desidratado em uma série de álcool etílico (30, 40, 50, 60, 70, 80, 90, 100%), levado ao secador de ponto crítico (CO2), montado, metalizado com ouro - paládio (35 nm) e, por fim, observados e eletromicrografados em microscópio eletrônico de varredura JEOL JSM 5410 (operado em 15 kV). Verificou-se que, aos seis dias após a enxertia, a soldadura para o porta-enxerto Passiflora alata já havia ocorrido, o que só foi constatado para Passiflora edulis f. flavicarpa aos nove dias. Também, aos nove dias, observou-se para ambos os porta-enxertos a completa formação da ponte de calo, indicando que, a partir daí, pode-se iniciar o processo de aclimatação da muda, para levá-la a um ambiente de menor umidade.

Morphological and biomechanical study of abdominal aorta of rats submitted to experimental chronic alcoholism

OBJETIVO: avaliar a influência do alcoolismo crônico experimental na morfologia e biomecânica da artéria aorta de ratos. MÉTODOS:ratos Wistar foram divididos em dois grupos de 22 animais. Grupo alcoolista: os ratos receberam água com concentração crescente de etanol e ração ad libitum durante 6 meses. Grupo controle: os animais receberam água e ração ad libitum pelo mesmo período. Os animais foram sacrificados com overdose de pentobarbital e as aortas abdominais foram excisadas para realização de histologia (hematoxilina-eosina, tricrômio de Masson, Calleja, Picrosirius red), histomorfometria e avaliação biomecânica (carga máxima, alongamento na carga máxima, limite de proporcionalidade, alongamento no limite de proporcionalidade e coeficiente de rigidez). RESULTADOS: A histologia e a histomorfometria não mostraram diferenças significantes na morfologia da aorta em ambos os grupos. A avaliação biomecânica mostrou aumento do alongamento no limite de proporcionalidade no grupo alcoolista (p<0.05). CONCLUSÃO: o alcoolismo crônico experimental não provocou alterações morfológicas na parede da aorta, mas causou aumento da sua elasticidade, sem modificar as outras propriedades mecânicas avaliadas.

Conjunctival impression cytology in dogs

Objective Ocular conjunctivas of healthy dogs were studied by conjunctival impression cytology for evaluation of feasibility, protocol standardization, and normal cytologic pattern recognition of this technique.Animals studied Twenty healthy, adult, cross-breed dogs.Procedures Samples of the bulbar conjunctiva were collected after instillation of topical anesthetic drops at the ocular surface. Impression cytology was performed by applying asymmetric strips of Millipore filter on the superior temporal bulbar conjunctiva near the limbus. The filter strip was gently pressed against the conjunctiva for 5 s and removed with a peeling motion. Samples were immediately fixed in 95% ethyl alcohol, stained with periodic acid-Schiff and hematoxylin, and mounted on slides cover-slipped using synthetic resin. The slides were examined by light microscopy.Results Microscopic examination of the impressions revealed superficial, intermediate and basal epithelial cells arranged in sheets. Keratinized epithelial cells, goblet cells and leukocytes, as well as cellular debris and mucus were observed.Conclusions Feasibility of impression cytology for sampling the bulbar conjunctiva of the dog and the standardization the the proposed protocol was shown. The results allowed the recognition the the normal cytologic pattern of healthy conjunctivas in dogs.