Estudo sobre o funcionamento de sistema de controle de tração em veículos automotores

This study explores the subject of traction control systems through bibliografy review on the spot of Mechanical Engineering. This paper has the objetivo of high light the main components and tecnology involved since MaxTrac system in 1971. It describes systems controled by throttle valve and breaks. Additionally, it i also presented basic knowlodged regarding electronic control unit and wheel sensors

Identificação de funções de transferência de ordem fracionária utilizando como entrada um degrau

Pós-graduação em Engenharia Elétrica - FEIS

Analysis and Prediction of Transient Opacity Spikes Using Dimensional Modeling

Dimensional modeling, GT-Power in particular, has been used for two related purposes-to quantify and understand the inaccuracies of transient engine flow estimates that cause transient smoke spikes and to improve empirical models of opacity or particulate matter used for engine calibration. It has been proposed by dimensional modeling that exhaust gas recirculation flow rate was significantly underestimated and volumetric efficiency was overestimated by the electronic control module during the turbocharger lag period of an electronically controlled heavy duty diesel engine. Factoring in cylinder-to-cylinder variation, it has been shown that the electronic control module estimated fuel-Oxygen ratio was lower than actual by up to 35% during the turbocharger lag period but within 2% of actual elsewhere, thus hindering fuel-Oxygen ratio limit-based smoke control. The dimensional modeling of transient flow was enabled with a new method of simulating transient data in which the manifold pressures and exhaust gas recirculation system flow resistance, characterized as a function of exhaust gas recirculation valve position at each measured transient data point, were replicated by quasi-static or transient simulation to predict engine flows. Dimensional modeling was also used to transform the engine operating parameter model input space to a more fundamental lower dimensional space so that a nearest neighbor approach could be used to predict smoke emissions. This new approach, intended for engine calibration and control modeling, was termed the "nonparametric reduced dimensionality" approach. It was used to predict federal test procedure cumulative particulate matter within 7% of measured value, based solely on steady-state training data. Very little correlation between the model inputs in the transformed space was observed as compared to the engine operating parameter space. This more uniform, smaller, shrunken model input space might explain how the nonparametric reduced dimensionality approach model could successfully predict federal test procedure emissions when roughly 40% of all transient points were classified as outliers as per the steady-state training data.

Microfabricated structures for integrated DNA analysis.

Photolithographic micromachining of silicon is a candidate technology for the construction of high-throughput DNA analysis devices. However, the development of complex silicon microfabricated systems has been hindered in part by the lack of a simple, versatile pumping method for integrating individual components. Here we describe a surface-tension-based pump able to move discrete nanoliter drops through enclosed channels using only local heating. This thermocapillary pump can accurately mix, measure, and divide drops by simple electronic control. In addition, we have constructed thermal-cycling chambers, gel electrophoresis channels, and radiolabeled DNA detectors that are compatible with the fabrication of thermocapillary pump channels. Since all of the components are made by conventional photolithographic techniques, they can be assembled into more complex integrated systems. The combination of pump and components into self-contained miniaturized devices may provide significant improvements in DNA analysis speed, portability, and cost. The potential of microfabricated systems lies in the low unit cost of silicon-based construction and in the efficient sample handling afforded by component integration.

Unidade microcontroladora para gerenciamento eletrônico de um motor de combustão interna ciclo Otto.

Nas últimas décadas, a indústria automobilística mundial vem investindo no desenvolvimento tecnológico dos motores, com o objetivo de alcançar melhor eficiência energética e atender às legislações que limitam a quantidade de resíduos tóxicos nos gases de exaustão e menor consumo de combustível. Isso resultou na implantação dos sistemas de gerenciamento eletrônico do motor, que possibilitam funcionalidades para se controlar diversas variáveis do motor, aumentando consideravelmente o rendimento do motor. Este trabalho tem como objetivos explorar a dinâmica de um motor de combustão interna ciclo Otto, os sinais elétricos associados, e os componentes de seu gerenciamento eletrônico. A partir dessas informações, o trabalho apresenta o processo de analise dos sinais elétricos e as estratégias de controle utilizadas em um sistema de gerenciamento real. Assim, são desenvolvidos o hardware e o firmware de uma unidade microcontroladora para gerenciamento eletrônico do motor. O hardware foi elaborado com uma concepção centralizada, ou seja, foi usado apenas um microcontrolador de 32-bit para gerenciar todas as funções. O firmware de controle foi desenvolvido de forma modular baseado em modelos de malha fechada. O modelo matemático do motor foi identificado utilizando técnicas de controle em um veículo real, e a avalidação do modelo foi obtida através de testes em um dinamômetro inercial.

Direct support and general support maintenance repair parts and special tools list including depot maintenance repair parts and special tools for azimuth laying set, guided missile AN/TSQ-110(X0-1) 1430-00-399-5318, encoder, shaft angle, digital (in container) 1430-01-034-2268, gyro reference unit (in container) 1430-01-033-4044 ...

Includes index.

Technology of instrumentation.

Mode of access: Internet.

Otimização do controle do diagrama de radiação de radares de varredura para rastreio de foguetes usando o método GAMMC para o Caso Planar (GAMMC-P)

Launching centers are designed for scientific and commercial activities with aerospace vehicles. Rockets Tracking Systems (RTS) are part of the infrastructure of these centers and they are responsible for collecting and processing the data trajectory of vehicles. Generally, Parabolic Reflector Radars (PRRs) are used in RTS. However, it is possible to use radars with antenna arrays, or Phased Arrays (PAs), so called Phased Arrays Radars (PARs). Thus, the excitation signal of each radiating element of the array can be adjusted to perform electronic control of the radiation pattern in order to improve functionality and maintenance of the system. Therefore, in the implementation and reuse projects of PARs, modeling is subject to various combinations of excitation signals, producing a complex optimization problem due to the large number of available solutions. In this case, it is possible to use offline optimization methods, such as Genetic Algorithms (GAs), to calculate the problem solutions, which are stored for online applications. Hence, the Genetic Algorithm with Maximum-Minimum Crossover (GAMMC) optimization method was used to develop the GAMMC-P algorithm that optimizes the modeling step of radiation pattern control from planar PAs. Compared with a conventional crossover GA, the GAMMC has a different approach from the conventional one, because it performs the crossover of the fittest individuals with the least fit individuals in order to enhance the genetic diversity. Thus, the GAMMC prevents premature convergence, increases population fitness and reduces the processing time. Therefore, the GAMMC-P uses a reconfigurable algorithm with multiple objectives, different coding and genetic operator MMC. The test results show that GAMMC-P reached the proposed requirements for different operating conditions of a planar RAV.

Privacy oriented access control for electronic health records

Security and privacy in electronic health record systems have been hindering the growth of e-health systems since their emergence. The development of policies that satisfy the security and privacy requirements of different stakeholders in healthcare has proven to be difficult. But, these requirements have to be met if the systems developed are to succeed in achieving their intended goals. Access control is a fundamental security barrier for securing data in healthcare information systems. In this paper we present an access control model for electronic health records. We address patient privacy requirements, confidentiality of private information and the need for flexible access for health professionals for electronic health records. We carefully combine three existing access control models and present a novel access control model for EHRs which satisfies requirements of electronic health records.

Privacy oriented access control for electronic health records

Information privacy is a critical success/failure factor in information technology supported healthcare (eHealth). eHealth systems utilise electronic health records (EHR) as the main source of information, thus, implementing appropriate privacy preserving methods for EHRs is vital for the proliferation of eHealth. Whilst information privacy may be a fundamental requirement for eHealth consumers, healthcare professionals demand non-restricted access to patient information for improved healthcare delivery, thus, creating an environment where stakeholder requirements are contradictory. Therefore, there is a need to achieve an appropriate balance of requirements in order to build successful eHealth systems. Towards achieving this balance, a new genre of eHealth systems called Accountable-eHealth (AeH) systems has been proposed. In this paper, an access control model for EHRs is presented that can be utilised by AeH systems to create information usage policies that fulfil both stakeholders’ requirements. These policies are used to accomplish the aforementioned balance of requirements creating a satisfactory eHealth environment for all stakeholders. The access control model is validated using a Web based prototype as a proof of concept.

Dual emissive borane-BODIPY dyads: molecular conformation control over electronic properties and fluorescence response towards fluoride ions

Facile synthesis of two new dimesitylboryl appended BODIPYs is reported. The two dyads have similar fluorescent chromophores but differ in their molecular conformations. They exhibit dual fluorescence, intramolecular energy transfer between boryl and BODIPY chromophores and different fluorescence responses (emission enhancement and quenching) upon fluoride binding.

Liquid crystal multi-mode lenses and axicons based on electronic phase shift control

We report on the principle of operation, construction and testing of a liquid crystal lens which is controlled by distributing voltages across the control electrodes, which are in turn controlled by adjusting the phase of the applied voltages. As well as (positive and negative) defocus, then lenses can be used to control tip/tilt, astigmatism, and to create variable axicons. © 2007 Optical Society of America.