EXPERIMENTAL INVESTIGATION OF CERTAIN INTERNAL CONDENSING AND BOILING FLOWS: THEIR SENSITIVITY TO PRESSURE FLUCTUATIONS AND HEAT TRANSFER ENHANCEMENTS

Space-based (satellite, scientific probe, space station, etc.) and millimeter – to – microscale (such as are used in high power electronics cooling, weapons cooling in aircraft, etc.) condensers and boilers are shear/pressure driven. They are of increasing interest to system engineers for thermal management because flow boilers and flow condensers offer both high fluid flow-rate-specific heat transfer capacity and very low thermal resistance between the fluid and the heat exchange surface, so large amounts of heat may be removed using reasonably-sized devices without the need for excessive temperature differences. However, flow stability issues and degradation of performance of shear/pressure driven condensers and boilers due to non-desirable flow morphology over large portions of their lengths have mostly prevented their use in these applications. This research is part of an ongoing investigation seeking to close the gap between science and engineering by analyzing two key innovations which could help address these problems. First, it is recommended that the condenser and boiler be operated in an innovative flow configuration which provides a non-participating core vapor stream to stabilize the annular flow regime throughout the device length, accomplished in an energy-efficient manner by means of ducted vapor re-circulation. This is demonstrated experimentally. Second, suitable pulsations applied to the vapor entering the condenser or boiler (from the re-circulating vapor stream) greatly reduce the thermal resistance of the already effective annular flow regime. For experiments reported here, application of pulsations increased time-averaged heat-flux up to 900 % at a location within the flow condenser and up to 200 % at a location within the flow boiler, measured at the heat-exchange surface. Traditional fully condensing flows, reported here for comparison purposes, show similar heat-flux enhancements due to imposed pulsations over a range of frequencies. Shear/pressure driven condensing and boiling flow experiments are carried out in horizontal mm-scale channels with heat exchange through the bottom surface. The sides and top of the flow channel are insulated. The fluid is FC-72 from 3M Corporation.

OPAC Design Enhancements and Their Effects on Circulation and Resource Sharing within the Library Consortium Environment

A longitudinal study of three discrete online public access catalog (OPAC) design enhancements examined the possible effects such changes may have on circulation and resource sharing within the automated library consortium environment. Statistical comparisons were made of both circulation and interlibrary loan (ILL) figures from the year before enhancement to the year after implementation. Data from sixteen libraries covering a seven-year period were studied in order to determine the degree to which patrons may or may not utilize increasingly broader OPAC ILL options over time. Results indicated that while ILL totals increased significantly after each OPAC enhancement, such gains did not result in significant corresponding changes in total circulation.

BAliBASE (Benchmark Alignment dataBASE): enhancements for repeats, transmembrane sequences and circular permutations

BAliBASE is specifically designed to serve as an evaluation resource to address all the problems encountered when aligning complete sequences. The database contains high quality, manually constructed multiple sequence alignments together with detailed annotations. The alignments are all based on three-dimensional structural superpositions, with the exception of the transmembrane sequences. The first release provided sets of reference alignments dealing with the problems of high variability, unequal repartition and large N/C-terminal extensions and internal insertions. Here we describe version 2.0 of the database, which incorporates three new reference sets of alignments containing structural repeats, trans­membrane sequences and circular permutations to evaluate the accuracy of detection/prediction and alignment of these complex sequences. BAliBASE can be viewed at the web site http://www-igbmc.u-strasbg.fr/BioInfo/BAliBASE2/index.html or can be downloaded from ftp://ftp-igbmc.u-strasbg.fr/pub/BAliBASE2/.

Modeling magnetar outbursts: flux enhancements and the connection with short bursts and glitches

The availability of a large amount of observational data recently collected from magnetar outbursts is now calling for a complete theoretical study of outburst characteristics. In this Letter (the first of a series dedicated to modeling magnetar outbursts), we tackle the long-standing open issue of whether or not short bursts and glitches are always connected to long-term radiative outbursts. We show that the recent detection of short bursts and glitches seemingly unconnected to outbursts is only misleading our understanding of these events. We show that, in the framework of the starquake model, neutrino emission processes in the magnetar crust limit the temperature, and therefore the luminosity. This natural limit to the maximum luminosity makes outbursts associated with bright persistent magnetars barely detectable. These events are simply seen as a small luminosity increase over the already bright quiescent state, followed by a fast return to quiescence. In particular, this is the case for 1RXS J1708–4009, 1E 1841–045, SGR 1806–20, and other bright persistent magnetars. On the other hand, a similar event (with the same energetics) in a fainter source will drive a more extreme luminosity variation and longer cooling time, as for sources such as XTE J1810–197, 1E 1547–5408, and SGR 1627–41. We conclude that the non-detection of large radiative outbursts in connection with glitches and bursts from bright persistent magnetars is not surprising per se, nor does it need any revision of the glitches and burst mechanisms as explained by current theoretical models.

Investigation of Performance Enhancements for a Liquid-Desiccant Solar Air-Conditioner

Thermally driven liquid-desiccant air-conditioners (LDAC) are a proven but still developing technology. LDACs can use a solar thermal system to reduce the operational cost and environmental impact of the system by reducing the amount of fuel (e.g. natural gas, propane, etc.) used to drive the system. LDACs also have a key benefit of being able to store energy in the form of concentrated desiccant storage. TRNSYS simulations were used to evaluate several different methods of improving the thermal and electrical coefficients of performance (COPt and COPe) and the solar fraction (SF) of a LDAC. The study analyzed a typical June to August cooling season in Toronto, Ontario. Utilizing properly sized, high-efficiency pumps increased the COPe to 3.67, an improvement of 55%. A new design, featuring a heat recovery ventilator on the scavenging-airstream and an energy recovery ventilator on the process-airstream, increased the COPt to 0.58, an improvement of 32%. This also improved the SF slightly to 54%, an increase of 8%. A new TRNSYS TYPE was created to model a stratified desiccant storage tank. Different volumes of desiccant were tested with a range of solar array system sizes. The largest storage tank coupled with the largest solar thermal array showed improvements of 64% in SF, increasing the value to 82%. The COPe was also improved by 17% and the COPt by 9%. When combining the heat recovery systems and the desiccant storage systems, the simulation results showed a 78% increase in COPe and 30% increase in COPt. A 77% improvement in SF and a 17% increase in total cooling rate were also predicted by the simulation. The total thermal energy consumed was 10% lower and the electrical consumption was 34% lower. The amount of non-renewable energy needed from the natural gas boiler was 77% lower. Comparisons were also made between LDACs and vapour-compression (VC) systems. Dependent on set-up, LDACs provided higher latent cooling rates and reduced electrical power consumption. Negatively, a thermal input was required for the LDAC systems but not for the VC systems.

A computer program (VEHSIM) for vehicle fuel economy and performance simulation (automobiles and light trucks). Volume IV: enhancements. Final report.

National Highway Traffic Safety Administration, Office of Research and Development, Washington D.C.

Enhancements to passive warning devices at railroad-highway grade crossings.

Texas Department of Transportation, Austin

Arms sales package to Saudi Arabia : hearings before the Committee on Foreign Relations, United States Senate, Ninety-seventh Congress, first session, on the AWACS and F-15 enhancements arms sales package to Saudi Arabia, October 1, 5, 6, 14, and 15, 1981

Item 1039-A, 1039-B (microfiche)

Technological enhancements to optometric clinical tests

A sizeable amount of the testing in eye care, requires either the identification of targets such as letters to assess functional vision, or the subjective evaluation of imagery by an examiner. Computers can render a variety of different targets on their monitors and can be used to store and analyse ophthalmic images. However, existing computing hardware tends to be large, screen resolutions are often too low, and objective assessments of ophthalmic images unreliable. Recent advances in mobile computing hardware and computer-vision systems can be used to enhance clinical testing in optometry. High resolution touch screens embedded in mobile devices, can render targets at a wide variety of distances and can be used to record and respond to patient responses, automating testing methods. This has opened up new opportunities in computerised near vision testing. Equally, new image processing techniques can be used to increase the validity and reliability of objective computer vision systems. Three novel apps for assessing reading speed, contrast sensitivity and amplitude of accommodation were created by the author to demonstrate the potential of mobile computing to enhance clinical measurement. The reading speed app could present sentences effectively, control illumination and automate the testing procedure for reading speed assessment. Meanwhile the contrast sensitivity app made use of a bit stealing technique and swept frequency target, to rapidly assess a patient’s full contrast sensitivity function at both near and far distances. Finally, customised electronic hardware was created and interfaced to an app on a smartphone device to allow free space amplitude of accommodation measurement. A new geometrical model of the tear film and a ray tracing simulation of a Placido disc topographer were produced to provide insights on the effect of tear film breakdown on ophthalmic images. Furthermore, a new computer vision system, that used a novel eye-lash segmentation technique, was created to demonstrate the potential of computer vision systems for the clinical assessment of tear stability. Studies undertaken by the author to assess the validity and repeatability of the novel apps, found that their repeatability was comparable to, or better, than existing clinical methods for reading speed and contrast sensitivity assessment. Furthermore, the apps offered reduced examination times in comparison to their paper based equivalents. The reading speed and amplitude of accommodation apps correlated highly with existing methods of assessment supporting their validity. Their still remains questions over the validity of using a swept frequency sine-wave target to assess patient’s contrast sensitivity functions as no clinical test provides the range of spatial frequencies and contrasts, nor equivalent assessment at distance and near. A validation study of the new computer vision system found that the authors tear metric correlated better with existing subjective measures of tear film stability than those of a competing computer-vision system. However, repeatability was poor in comparison to the subjective measures due to eye lash interference. The new mobile apps, computer vision system, and studies outlined in this thesis provide further insight into the potential of applying mobile and image processing technology to enhance clinical testing by eye care professionals.

Investigation of Performance Enhancements for a Liquid-Desiccant Solar Air-Conditioner

Thermally driven liquid-desiccant air-conditioners (LDAC) are a proven but still developing technology. LDACs can use a solar thermal system to reduce the operational cost and environmental impact of the system by reducing the amount of fuel (e.g. natural gas, propane, etc.) used to drive the system. LDACs also have a key benefit of being able to store energy in the form of concentrated desiccant storage. TRNSYS simulations were used to evaluate several different methods of improving the thermal and electrical coefficients of performance (COPt and COPe) and the solar fraction (SF) of a LDAC. The study analyzed a typical June to August cooling season in Toronto, Ontario. Utilizing properly sized, high-efficiency pumps increased the COPe to 3.67, an improvement of 55%. A new design, featuring a heat recovery ventilator on the scavenging-airstream and an energy recovery ventilator on the process-airstream, increased the COPt to 0.58, an improvement of 32%. This also improved the SF slightly to 54%, an increase of 8%. A new TRNSYS TYPE was created to model a stratified desiccant storage tank. Different volumes of desiccant were tested with a range of solar array system sizes. The largest storage tank coupled with the largest solar thermal array showed improvements of 64% in SF, increasing the value to 82%. The COPe was also improved by 17% and the COPt by 9%. When combining the heat recovery systems and the desiccant storage systems, the simulation results showed a 78% increase in COPe and 30% increase in COPt. A 77% improvement in SF and a 17% increase in total cooling rate were also predicted by the simulation. The total thermal energy consumed was 10% lower and the electrical consumption was 34% lower. The amount of non-renewable energy needed from the natural gas boiler was 77% lower. Comparisons were also made between LDACs and vapour-compression (VC) systems. Dependent on set-up, LDACs provided higher latent cooling rates and reduced electrical power consumption. Negatively, a thermal input was required for the LDAC systems but not for the VC systems.

Impeding good governance implementation in Indonesian regional government : the effect of a bureaucratic generation gap

The implementation of ‘good governance’ in Indonesia’s regional government sector became a central tenet in governance research following the introduction of the national code for governance in 2006. The code was originally drafted in 1999 as a response to the Asian financial crises and many cases of unearthed corruption, collusion, and nepotism. It was reviewed in 2001 and again in 2006 to incorporate relevant political, economical, and social developments. Even though the national code exists along with many regional government decrees on good governance, the extent of implementation of the tenets of good governance in Indonesia’s regional government is still questioned. Previous research on good governance implementation in Indonesian regional government (Mardiasmo, Barnes and Sakurai, 2008) identified differences in the nature and depth of implementation between various Indonesian regional governments. This paper analyses and extends this recent work and explores key factors that may impede the implementation and sustained application of governance practices across regional settings. The bureaucratic culture of Indonesian regional government is one that has been shaped for over approximately 30 years, in particular during that of the Soeharto regime. Previous research on this regime suggests a bureaucratic culture with a mix of positive and negative aspects. On one hand Soeharto’s regime resulted in strong development growth and strong economic fundamentals, resulting in Indonesia being recognised as one of the Asian economic tigers prior to the 1997 Asian financial crises. The financial crises however revealed a bureaucratic culture that was rife with corruption, collusion, and nepotism. Although subsequent Indonesian governments have been committed to eradicating entrenched practices it seems apparent that the culture is ingrained within the bureaucracy and eradication of it will take time. Informants from regional government agree with this observation, as they identify good governance as an innovative mechanism and to implement it will mean a deviation from the “old ways.” Thus there is a need for a “changed” mind set in order to implement sustained governance practices. Such an exercise has proven to be challenging so far, as there is “hidden” resistance from within the bureaucracy to change its ways. The inertia of such bureaucratic cultures forms a tension against the opportunity for the implementation of good governance. From this context an emergent finding is the existence of a ‘bureaucratic generation gap’ as an impeding variable to enhanced and more efficient implementation of governance systems. It was found that after the Asian financial crises the Indonesian government (both at national and regional level) drew upon a wider human resources pool to fill government positions – including entrants from academia, the private sector, international institutions, foreign nationals and new graduates. It suggested that this change in human capital within government is at the core of this ‘inter-generational divide.’ This divergence is exemplified, at one extreme, by [older] bureaucrats who have been in-position for long periods of time serving during the extended Soeharto regime. The “new” bureaucrats have only sat in their positions since the end of Asian financial crisis and did not serve during Soeharto’s regime. It is argued that the existence of this generation gap and associated aspects of organisational culture have significantly impeded modernising governance practices across regional Indonesia. This paper examines the experiences of government employees in five Indonesian regions: Solok, Padang, Gorontalo, Bali, and Jakarta. Each regional government is examined using a mixed methodology comprising of on-site observation, document analysis, and iterative semi-structured interviewing. Drawing from the experiences of five regional governments in implementing good governance this paper seeks to better understand the causal contexts of variable implementation governance practices and to suggest enhancements to the development of policies for sustainable inter-generational change in governance practice across regional government settings.

Evidence-based practice and information literacy

Evidence-based Practice (EBP) has recently emerged as a topic of discussion amongst professionals within the library and information services (LIS) industry. Simply stated, EBP is the process of using formal research skills and methods to assist in decision making and establishing best practice. The emerging interest in EBP within the library context serves to remind the library profession that research skills and methods can help ensure that the library industry remains current and relevant in changing times. The LIS sector faces ongoing challenges in terms of the expectation that financial and human resources will be managed efficiently, particularly if library budgets are reduced and accountability to the principal stakeholders is increased. Library managers are charged with the responsibility to deliver relevant and cost effective services, in an environment characterised by rapidly changing models of information provision, information access and user behaviours. Consequently they are called upon not only to justify the services they provide, or plan to introduce, but also to measure the effectiveness of these services and to evaluate the impact on the communities they serve. The imperative for innovation in and enhancements to library practice is accompanied by the need for a strong understanding of the processes of review, measurement, assessment and evaluation. In 2001 the Centre for Information Research was commissioned by the Chartered Institute of Library and Information Professionals (CILIP) in the UK to conduct an examination into the research landscape for library and information science. The examination concluded that research is “important for the LIS [library and information science] domain in a number of ways” (McNicol & Nankivell, 2001, p.77). At the professional level, research can inform practice, assist in the future planning of the profession, raise the profile of the discipline, and indeed the reputation and standing of the library and information service itself. At the personal level, research can “broaden horizons and offer individuals development opportunities” (McNicol & Nankivell, 2001, p.77). The study recommended that “research should be promoted as a valuable professional activity for practitioners to engage in” (McNicol & Nankivell, 2001, p.82). This chapter will consider the role of EBP within the library profession. A brief review of key literature in the area is provided. The review considers issues of definition and terminology, highlights the importance of research in professional practice and outlines the research approaches that underpin EBP. The chapter concludes with a consideration of the specific application of EBP within the dynamic and evolving field of information literacy (IL).

Exploring how parents and peers influence the behaviour of young drivers

Despite ongoing enhancements to graduated licensing systems, young drivers continue to have a high risk of being killed or injured in car crashes. This study investigated the influence of parents and peers on the risky behaviour of young drivers, utilising Akers’ social learning theory. The specific factors examined related to parent and peer norms perceived by the young driver, and the rewards and punishments anticipated by the young driver from their parents and peers. A questionnaire was completed by 165 young drivers. Regression analysis revealed that these factors explained 54% of the variance in risky driving. The strongest predictor was anticipated parent rewards, followed by peer norms, and anticipated peer rewards. Exploratory analyses however revealed the profile of predictors varied for male and female participants, and for self-reported offenders and non-offenders. The results highlight the role of psychosocial factors in the risky behaviour of young drivers and the need for road safety policies and programs to consider the influence of both parents and peers upon this behaviour.

Theoretical and numerical investigation of plasmon nanofocusing in metallic tapered rods and grooves

Effective focusing of electromagnetic (EM) energy to nanoscale regions is one of the major challenges in nano-photonics and plasmonics. The strong localization of the optical energy into regions much smaller than allowed by the diffraction limit, also called nanofocusing, offers promising applications in nano-sensor technology, nanofabrication, near-field optics or spectroscopy. One of the most promising solutions to the problem of efficient nanofocusing is related to surface plasmon propagation in metallic structures. Metallic tapered rods, commonly used as probes in near field microscopy and spectroscopy, are of a particular interest. They can provide very strong EM field enhancement at the tip due to surface plasmons (SP’s) propagating towards the tip of the tapered metal rod. A large number of studies have been devoted to the manufacturing process of tapered rods or tapered fibers coated by a metal film. On the other hand, structures such as metallic V-grooves or metal wedges can also provide strong electric field enhancements but manufacturing of these structures is still a challenge. It has been shown, however, that the attainable electric field enhancement at the apex in the V-groove is higher than at the tip of a metal tapered rod when the dissipation level in the metal is strong. Metallic V-grooves also have very promising characteristics as plasmonic waveguides. This thesis will present a thorough theoretical and numerical investigation of nanofocusing during plasmon propagation along a metal tapered rod and into a metallic V-groove. Optimal structural parameters including optimal taper angle, taper length and shape of the taper are determined in order to achieve maximum field enhancement factors at the tip of the nanofocusing structure. An analytical investigation of plasmon nanofocusing by metal tapered rods is carried out by means of the geometric optics approximation (GOA), which is also called adiabatic nanofocusing. However, GOA is applicable only for analysing tapered structures with small taper angles and without considering a terminating tip structure in order to neglect reflections. Rigorous numerical methods are employed for analysing non-adiabatic nanofocusing, by tapered rod and V-grooves with larger taper angles and with a rounded tip. These structures cannot be studied by analytical methods due to the presence of reflected waves from the taper section, the tip and also from (artificial) computational boundaries. A new method is introduced to combine the advantages of GOA and rigorous numerical methods in order to reduce significantly the use of computational resources and yet achieve accurate results for the analysis of large tapered structures, within reasonable calculation time. Detailed comparison between GOA and rigorous numerical methods will be carried out in order to find the critical taper angle of the tapered structures at which GOA is still applicable. It will be demonstrated that optimal taper angles, at which maximum field enhancements occur, coincide with the critical angles, at which GOA is still applicable. It will be shown that the applicability of GOA can be substantially expanded to include structures which could be analysed previously by numerical methods only. The influence of the rounded tip, the taper angle and the role of dissipation onto the plasmon field distribution along the tapered rod and near the tip will be analysed analytically and numerically in detail. It will be demonstrated that electric field enhancement factors of up to ~ 2500 within nanoscale regions are predicted. These are sufficient, for instance, to detect single molecules using surface enhanced Raman spectroscopy (SERS) with the tip of a tapered rod, an approach also known as tip enhanced Raman spectroscopy or TERS. The results obtained in this project will be important for applications for which strong local field enhancement factors are crucial for the performance of devices such as near field microscopes or spectroscopy. The optimal design of nanofocusing structures, at which the delivery of electromagnetic energy to the nanometer region is most efficient, will lead to new applications in near field sensors, near field measuring technology, or generation of nanometer sized energy sources. This includes: applications in tip enhanced Raman spectroscopy (TERS); manipulation of nanoparticles and molecules; efficient coupling of optical energy into and out of plasmonic circuits; second harmonic generation in non-linear optics; or delivery of energy to quantum dots, for instance, for quantum computations.