Bone structure assessed by HR-pQCT, TBS and DXL in adult patients with different types of osteogenesis imperfecta.

UNLABELLED: Bone microarchitecture by high-resolution peripheral quantitative computed tomography (HR-pQCT) was assessed in adult patients with mild, moderate, and severe osteogenesis imperfecta (OI). The trabecular bone score (TBS), bone mineral density (BMD) by dual-energy X-ray absorptiometry (DXA), and dual X-ray and laser (DXL) at the calcaneus were likewise assessed in patients with OI. Trabecular microstructure and BMD in particular were severely altered in patients with OI. INTRODUCTION: OI is characterized by high fracture risk but not necessarily by low BMD. The main purpose of this study was to assess bone microarchitecture and BMD at different skeletal sites in different types of OI. METHODS: HR-pQCT was performed in 30 patients with OI (mild OI-I, n = 18 (41.8 [34.7, 55.7] years) and moderate to severe OI-III-IV, n = 12 (47.6 [35.3, 58.4] years)) and 30 healthy age-matched controls. TBS, BMD by DXA at the lumbar spine and hip, as well as BMD by DXL at the calcaneus were likewise assessed in patients with OI only. RESULTS: At the radius, significantly lower trabecular parameters including BV/TV (p = 0.01 and p < 0.0001, respectively) and trabecular number (p < 0.0001 and p < 0.0001, respectively) as well as an increased inhomogeneity of the trabecular network (p < 0.0001 and p < 0.0001, respectively) were observed in OI-I and OI-III-IV in comparison to the control group. Similar results for trabecular parameters were found at the tibia. Microstructural parameters were worse in OI-III-IV than in OI-I. No significant differences were found in cortical thickness and cortical porosity between the three subgroups at the radius. The cortical thickness of the tibia was thinner in OI-I (p < 0.001), but not OI-III-IV, when compared to controls. CONCLUSIONS: Trabecular BMD and trabecular bone microstructure in particular are severely altered in patients with clinical OI-I and OI-III-IV. Low TBS and DXL and their significant associations to HR-pQCT parameters of trabecular bone support this conclusion.

The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Institutional environment in North Korea: market structure and overcoming institutional voids

Tutkimus sai innoituksensa, kun tutkija huomasi tarpeen liiketaloudelliselle, ajantasaiselle ja realistiselle tutkimukselle Pohjois-Korean markkinoista, joka kuvailisi markkinoiden olemassaolevia ja puuttuvia rakenteita sekä tutkisi mahdollisuuksia ylittää puuttuvat rakenteet. Institutionaalinen teoria valittiin sopivaksi viitekehykseksi kuvailla ja tutkia markkinarakennetta. Tutkimuskysymys muotoiltiin seuraavasti: “Miten ulkomaiset yritykset voivat reagoida puuttuviin markkinarakenteisiin Pohjois-Koreassa?”. Tutkimuskysymys jaettiin kolmeen osakysymykseen: (1) Millainen on Pohjois-Korean markkinoiden institutionaalinen ympäristö? (2) Mitkä ovat merkittävimmät puuttuvat markkinarakenteet Pohjois-Koreassa? (3) Mitä mahdollisuuksia ulkomaisilla yrityksillä voisi olla reagoida puuttuviin markkinarakenteisiin? Tutkimus toteutettiin kvalitatiivisena, koska tutkimuskysymys on deskriptiivinen. Aineisto kerättiin asiantuntijahaastattelun ja kvalitatiivisen sisällönanalyysin keinoin. Primääriaineiston muodostavat 2 asiantuntijahaastattelua ja sekundääriaineiston muodostavat 95 artikkelia, jotka kerättiin 40 lähteestä. Aineisto analysoitiin kvalitatiivisen sisällönanalyysin keinoin. Aineisto koodattiin, luokiteltiin ja esitettiin kokonaisuuksina luokittelurungon avulla, joka laadittiin tutkimusta varten muodostetun teoreettisen viitekehyksen mukaan. Tulokset ja johtopäätökset voidaan tiivistää seuraavasti. (1) Pohjois-Korean markkinan instituutioihin vaikuttaa kaksoisrakenne, jossa muodollinen, sosialistinen rakenne ja epämuodollinen, markkinalähtöinen rakenne toimivat päällekkäin. (2) Puuttuvia rakenteita on sekä markkinan kontekstissa että markkinatasolla. Puutteet ovat osittain seurausta vanhojen rakenteiden korvaantumisesta uusilla, jotka eivät ole institutionalisoituneet. (3) Yritykset voivat käyttää samoja mahdollisuuuksia reagoida puuttuviin markkinarakenteisiin Pohjois-Koreassa, joita kehittyvien markkinoiden yhteydessä on esitetty. Sen tulkittiin vähentävän käsitystä, jonka mukaan Pohjois-Korean markkina on liian erikoinen yritystoiminnalle. (4) Kasvava keskiluokka sekä yrittäjyyden ja naisten yhä merkittävämpi rooli liike-elämässä aiheuttavat alhaalta ylöspäin suuntautuvaa kehitystä markkinoilla. Nämä ovat merkkejä viimeaikaisesta kehityksestä, jotka eivät ole saaneet laajaa huomiota länsimaisessa mediassa. Se korostaa tarvetta liiketaloudelliselle, ajantasaiselle jatkotutkimukselle Pohjois-Korean markkinoista.

Institutional environment in North Korea: market structure and overcoming institutional voids

The research was sparked by an exchange in South Korea, as the author identified a gap in research that provides economic, up to date and realistic information about the North Korean market in English language. A need for a research was identified that would describe the market’s existing and missing market structures and explore possibilities to overcome the missing market structures. Institutional theory was chosen as a suitable framework to describe and explore the market. The research question was formulated as follows: “How can foreign companies overcome institutional voids in the North Korean market?”. To answer the research question, it was divided into three sub-questions as follows: (1) What is the institutional environment in North Korea like? (2) What are the major institutional voids in the North Korean market? (3) What possibilities do foreign companies have to overcome institutional voids? The research is qualitative by nature due to the descriptive and exploratory nature of the research question. Data collection consisted of expert interview and content analysis, resulting in primary data of two interviews and secondary data of 95 articles from 40 different sources. The data was analyzed with the systematical technique of content analysis. The data was coded, classified and presented as concepts with the help of a classification system that was build following the theoretical framework adapted for this study. The findings can be summarized as follows. (1) The market institutions are characterized by an overlapping dual system of formal, socialist structures and informal, market-oriented structures. (2) Institutional voids prevail on both the market’s contextual and on the market level. They are partly result of old institutions being replaced by new institutions that lack institutionalization. (3) Identified possibilities to overcome institutional voids correspond with possibilities drawn from previous research. This decreases the image of North Korea as an impossibly unique market to operate in. (4) Emerging middle class, rapidly growing entrepreneurial activities and women’s increasing role in business drive a down-to-up change in the market. This signals the recent development of the market, yet has been overlooked in the Western media. Thus there is a need for further economic, up to date research concerning North Korea.

New Building Blocks for Dual-Property Molecule-Based Magnets

Two classes of compounds have been prepared and characterized as building blocks for chiral magnets and ferromagnetic conductors. In the fIrst project, the organic framework of a pentadentate, (N302) macro cycle has been synthetically modifIed to introduce phenyl substituents into its organic framework and the synthesis of four new [Fe(In(N302)(CN)2] complexes (I) - (IV) is presented. [Molecular diagram availble in pdf] This work represents the fIrst structural and magnetic studies of a family of spin crossover macrocycles that comprise of both structural and stereo-isomers. Magnetic susceptibility and Mossbauer data for the R,R-complex (I) is consistent with both a thermal and a light induced spin crossover transition. The X-ray data supports a change in geometry accompanying the thermal spin transition, from a high spin (HS) 7 -coordinate complex at room temperature to a low spin (LS) 5-coordinate complex at 100 K. The crystal structure ofthe racemic complex (III) reveals a HS, 7-coordinate complex at 200 K that undergoes no signifIcant structural changes on cooling. In contrast, the magnetic - susceptibility and Mossbauer data collected on a powder sample of the racemic complex are consistent with a LS complex. Finally, the meso complex (IV) was prepared and its structure and magnetic properties are consistent with a 5-coordinate LS complex that remains low spin, but undergoes conformational changes on cooling in solution. The chiral [Fe(H)(N302)(CN)2] macro cycle (I), together with its Mn(H) and Fe(H) derivatives have also been exploited as building blocks for the self-assembly of chiral magnets. In the second project, a synthetic route for the preparation of tetrathiafulvalene (TTF) donors covalently attached to a diisopropyl verdazyl radical via a cross conjugated pyridyl linker IS presented. Following this strategy, four new TTF-py- (diisopropyl)verdazyl radicals have been prepared and characterized (V) - (VIII) . [Molecular diagram available in pdf] The first (2:1) charge transfer complex ofa TTF-py-(diisopropyl)verdazyl radical donor and a TCNQ acceptor has been prepared and structurally characterized. The crystal packing shows that the donor and acceptor molecules are organized in a mixed stacking arrangement consistent with its insulating behaviour. EPR and magnetic susceptibility data support intramolecular ferromagnetic interactions between the TTF and the verdazyl radicals and antiferromagnetic interactions between TTF donors within a stack. In an attempt to increase the intramolecular exchange interaction between the two radicals, a TTF-x-(diisopropyl)verdazyl radical (IX) was prepared, where the two radicals are connected ia a conjugated divinylene linker. The neutral radical donors stack in a more favourable head-to-head arrangement but the bulky isopropyl groups prevent the donor radicals from stacking close enough together to facilitate good orbital overlap. [Molecular diagram available in pdf].

Broadband dual frequency microstrip antenna

A new dual port microstrip antenna geometry for dual frequency operation is presented. The structure consists of the intersection of two circles of the same radius with their centres displaced by a small fraction of the wavelength . This antenna provides wide impedance bandwidth and excellent isolation between its ports. The gain of the antenna is comparable to that of a standard circular microstrip antenna operating at the same resonant frequency. A theoretical analysis for calculating the resonant frequencies of the two ports is also presented

Dual-band dual-polarized compact microstrip antenna

Experimental studies on a compact dual frequency microstrip antenna are presented. This antenna configuration provides an area reduction of 40% compared to a standard rectangular antenna operating at the same frequency without much degradation of the gain. The antenna structure can be modified to achieve the desired ratio between the two resonant frequencies

A novel radar-absorbing-material based on EBG structure

An innovative phaseshifterless, wideband, micrustrip leaky-wave antenna with an electronically steerable dual-pencil-beam pattern in the H-plane is presented. The log-periodic geometry of the leaky slots of the antenna results in a wide bandwidth of 25.19%. The Jan beam can he steered up to 14° over the wide resonating band of the anteww. The beam is also steerable at a fixed frequency. by reactivelty loading the slots and a maximum steering angle of about 14° is ohserved. for different capacitor values with an improved bandwidth of 33 _i%. This concept is studied using passive components but it can be extended to varactors

ACS fed printed F-shaped uniplanar antenna for dual band WLAN applications

An asymmetric coplanar strip (ACS) fed dual band F-shaped antenna covering the 2.4/5.2 GHz WLAN bands is presented. The optimized dimensions of the proposed uniplanar antenna are 21 mm × 19 mm when printed on a substrate of dielectric constant 4.4 and height 1.6 mm. The dual band nature of the antenna is brought about by the various current paths in the F-shaped structure and the ground plane. The antenna exhibits nearly omnidirectional radiation characteristics and moderate gain in both the operating bands. Details of the antenna design, simulation, and experimental results are presented and discussed.

An electromagnetically coupled dual-band dual-polarized microstrip antenna for WLAN applications

A new design of a dual-band dual-polarized electromagnetically coupled slot loaded square patch antenna, covering the WLAN 5.2 GHz and 5.8 GHz bands, achieving bandwidth enhancement by using tapered slot structure, is presented here. The proposed antenna covers 5.09–5.47 GHz and 5.7–5.88 GHz bands. Details of the antenna design along with experimental and simulated results are presented and discussed.

Compact dual band slot loaded circular microstrip antenna with a superstrate

Design of a compact dual frequency microstrip antenna is presented. The structure consists of a slotted circular patch with a dielectric superstrate. The superstrate,not only acts as a radome, but improves the bandwidth and lowers the resonant frequency also. The proposed design provides an overall size reduction of about 60% compared to an unslotted patch along with good efficiency,gain and bandwidth. The polarization planes at the two resonances are orthogonal and can be simultaneously excited using a coaxial feed. Parametric study of this configuration showed that the frequency ratio of the two resonances can be varied from 1.17 to 1.7 enabling its applications in the major wireless communication bands like AWS, DECT,PHS,Wi.Bro, ISM,and DMB. Design equations are also deduced for the proposed antenna and validated.

Compact dual-polarised square microstrip antenna with triangular slots for wireless communication

Design of a dual linearly-polarised microstrip patch antenna, excited by two orthogonal microstrip feed lines, is presented. A reduction in patch size of 35% is obtained when compared to a square patch operating at the same frequency. The polarisations are oriented at +45 and - 45 with an isolation of more than 36 dB between the ports. Unlike earlier designs, the proposed structure provides better gain.

Design of Compact Reconfigurable Dual Frequency Microstrip Antennas Using Varactor Diodes

The design of a compact, single feed, dual frequency dual polarized and electronically reconfigurable microstrip antenna is presented in this paper. A square patch loaded with a hexagonal slot having extended slot arms constitutes the fundamental structure of the antenna. The tuning of the two resonant frequencies is realized by varying the effective electrical length of the slot arms by embedding varactor diodes across the slots. A high tuning range of 34.43% (1.037–1.394 GHz) and 9.27% (1.359–1.485 GHz) is achieved for the two operating frequencies respectively, when the bias voltage is varied from 0 to −30 V. The salient feature of this design is that it uses no matching networks even though the resonant frequencies are tuned in a wide range with good matching below −10 dB. The antenna has an added advantage of size reduction up to 80.11% and 65.69% for the two operating frequencies compared to conventional rectangular patches.

Assessing the sources and magnitude of diurnal nitrate variability in the San Joaquin River (California) with an in-situ optical nitrate sensor and dual nitrate isotopes

We investigated diurnal nitrate (NO3-) concentration variability in the San Joaquin River using an in situ optical NO3- sensor and discrete sampling during a 5-day summer period characterized by high algal productivity. Dual NO3- isotopes (delta N-15(NO3) and delta O-18(NO3)) and dissolved oxygen isotopes (delta O-18(DO)) were measured over 2 days to assess NO3- sources and biogeochemical controls over diurnal time-scales. Concerted temporal patterns of dissolved oxygen (DO) concentrations and delta O-18(DO) were consistent with photosynthesis, respiration and atmospheric O-2 exchange, providing evidence of diurnal biological processes independent of river discharge. Surface water NO3- concentrations varied by up to 22% over a single diurnal cycle and up to 31% over the 5-day study, but did not reveal concerted diurnal patterns at a frequency comparable to DO concentrations. The decoupling of delta N-15(NO3) and delta O-18(NO3) isotopes suggests that algal assimilation and denitrification are not major processes controlling diurnal NO3- variability in the San Joaquin River during the study. The lack of a clear explanation for NO3- variability likely reflects a combination of riverine biological processes and time-varying physical transport of NO3- from upstream agricultural drains to the mainstem San Joaquin River. The application of an in situ optical NO3- sensor along with discrete samples provides a view into the fine temporal structure of hydrochemical data and may allow for greater accuracy in pollution assessment.

Dual-orthogonal radial basis function networks for nonlinear time series prediction

A new structure of Radial Basis Function (RBF) neural network called the Dual-orthogonal RBF Network (DRBF) is introduced for nonlinear time series prediction. The hidden nodes of a conventional RBF network compare the Euclidean distance between the network input vector and the centres, and the node responses are radially symmetrical. But in time series prediction where the system input vectors are lagged system outputs, which are usually highly correlated, the Euclidean distance measure may not be appropriate. The DRBF network modifies the distance metric by introducing a classification function which is based on the estimation data set. Training the DRBF networks consists of two stages. Learning the classification related basis functions and the important input nodes, followed by selecting the regressors and learning the weights of the hidden nodes. In both cases, a forward Orthogonal Least Squares (OLS) selection procedure is applied, initially to select the important input nodes and then to select the important centres. Simulation results of single-step and multi-step ahead predictions over a test data set are included to demonstrate the effectiveness of the new approach.