Metal transport parameters of a gneiss saprolitic silty soil for liner design

Diffusion coefficients and retardation factors of two metal cations (Cd2+ and Pb2+) were measured for a compacted Brazilian saprolitic soil derived from gneiss, aiming to assess its geoenvironmental performance as a liner for waste disposal sites. This soil occurs extensively all over the country in very thick layers, but has not been used in liners because of its hydraulic conductivity, higher than 10(-9) m/s when compacted at optimum water content of standard Proctor energy, but which can be reduced by means of appropriate compaction techniques or additives. Batch, column, and diffusion tests were carried out with monospecies synthetic solutions at pH 1, 3, and 5.5. Measured diffusion coefficients varied between 0.5 and 4 X 10(-10) m(2)/s. Retardation factors show that cadmium, a very mobile cation, is not adsorbed at pH I but is significantly retained at pH 3 and pH 5.5, whereas lead is retained at all tested pH values though slightly at pH 1. Estimated retardation factors from batch tests were 1.3-2.3 times those resulting from column tests and at its highest when obtained by diffusion tests; whereas batch tests allow a more complete exposure of the soil grains to the solution, time-dependent nonspecific adsorption may take longer to occur. The importance of contact time was observed and should be considered in further investigations. Its significant retention of metals suggests a promising utilization of this soil as a bottom liner for wastes landfills.

Contact pressure evolution and its relation to wear in sheet metal forming

For a given sheet metal forming process, an accurate determination of the contact pressure distribution is an essential step towards the estimation of tool life. This investigation utilizes finite element (FE) analysis to model and explain the evolution and distribution of contact pressure over the die radius, throughout the duration of a channel forming process. It was found that a typical two-peak steady-state contact pressure response exists for the majority of the process. However, this was preceded by an initial transient response, characterized by extremely large and localized contact pressures, which were more than double the magnitude of the steady-state peak pressure. The validity of the predicted contact pressure behavior was assessed via detailed numerical analysis and by examining the wear response of an experimental stamping operation. The experimental results revealed that the high contact pressure zones of the transient response corresponded to a severe galling wear mechanism. Therefore, the transient response may be of primary significance to the tool wear response; thus questioning the applicability of traditional bending-under-tension wear tests for sheet metal stamping processes. Finally, a parametric study was conducted, examining the influence of the major process parameters on the steady-state and peak transient contact pressures, using the developed FE model. It was found that the bend ratio and the blank material ultimate tensile strength had the most influence on the peak contact pressures. The main process-related parameters, friction coefficient and blank holder force, were found to have only a minor influence.

Data-driven computation of contact dynamics during two-point manipulation of deformable objects

This study represents a preliminary step towards data-driven computation of contact dynamics during manipulation of deformable objects at two points of contact. A modeling approach is proposed that characterizes the individual interaction at both points and the mutual effects of the two interactions on each other via a set of parameters. Both global as well as local coordinate systems are tested for encoding the contact mechanics. Artificial neural networks are trained on simulated data to capture the object behavior. A comparison of test data with the output of the trained system reveals a mean squared error percentage between 1% and 3% for simple interactions.

Inhibitory effect of antidepressant drugs on contact hypersensitivity reaction

Background: Contact hypersensitivity (CS) reaction in the skin is T-cell mediated immune reaction which plays a major role in the pathogenesis and chronicity of various inflammatory skin disorders and, like other delayed-type hypersensitivity (DTH) reactions, affords immunity against tumor cells and microbes. CS response is a self-limiting reaction, and interleukin (IL)-10 is considered to be a natural suppressant of cutaneous inflammatory response. Recently, it has been demonstrated that major depression is related to activation of the inflammatory response and elevation of some parameters of cell-mediated immunity. It has been suggested that such activation of the immune system may play a role in etiology of depression. If this immunoactivation is involved in etiology of depression, one would expect that antidepressant agents may have negative immunoregulatory effects. To the best of our knowledge, the effect of antidepressants on contact hypersensitivity has not been studied.

Methods: The aim of the present study was to establish the effect of prolonged desipramine or fluoxetine treatment on CS reaction to picryl chloride.

Results: Antidepressants significantly suppressed CS reaction, fluoxetine by 53% whereas desipramine by 47% compared to positive control. Moreover, desipramine and fluoxetine decreased relative weight of auxillary lymph nodes. Desipramine decreased also relative weight of inguinal lymph nodes and spleens whereas desipramine and fluoxetine increased production of IL-10 in comparison to positive control.

Conclusion: The observed effect of antidepressant drugs on CS reaction is consistent with the hypothesis that T-cell mediated immunity is targeted by antidepressants.

A hybrid contact state analysis methodology for robotic-based adjustment of cylindrical pair

The peg-in-hole insertion and adjustment operation is one of the most common tasks in the robotic and automatic assembly processes. Fine motion strategies associated with adjustment operations on a peg-in-hole are fundamental manipulations that can be utilised in dynamic assembly and reconfigurable workholding or fixturing systems. This paper presents a comprehensive study of robotic-based height adjustment of a cylindrical pair based on maintaining minimum contact forces between the links. The outer link is held by the end-effector of a six-DOF (Degrees of freedom) serial articulated robot manipulator. The environment represented by the inner link can be either static or dynamic. A force-based approach and a d value approach are established to determine the type of contact that exists between the links of a cylindrical pair, and to extract control parameters. Based on the comparison and analysis of these two approaches, a hybrid methodology is established by combining a d value approach with a force-based approach for contact state determination. Formulations capable of extracting necessary control parameters, which ensure minimum contact forces between the links, are established from both planar and spatial viewpoints under both static and dynamic environmental conditions. Experimental results demonstrate the effectiveness of the proposed methodology.

The TFOS international workshop on contact lens discomfort : report of the subcommittee on clinical trial design and outcomes

The goal of this report is to review previously published clinical trials addressing contact lens discomfort (CLD) to identify appropriate trial design and outcome parameters to guide future clinical research that will characterize and investigate possible causes of CLD. A further goal is to identify possible confounding features of clinical trial design and performance in order to reduce bias in conduct of future trials or analysis of data from those trials.

Modeling a system of phosphated cross-linked high amylose for controlled drug release. Part 2: Physical parameters, cross-linking degrees and drug delivery relationships

High amylose cross-linked to different degrees with sodium trimetaphosphate by varying base strength (2% or 4%) and contact time (0.5-4 h) was evaluated as non-compacted systems for sodium diclophenac controlled release. The physical properties and the performance of these products for sodium diclophenac controlled release from non-compacted systems were related to the structures generated at each cross-linking degree. For samples at 2% until 2 h the swelling ability, G' and eta* values increased with the cross-linking degree, because the longer polymer chains became progressively more entangled and linked. This increases water uptake and holding, favoring the swelling and resulting in systems with higher viscosities. Additionally, the increase of cross-linking degree should contribute for a more elastic structure. The shorter chains with more inter-linkages formed at higher cross-linking degrees (2%4h and 4%) make water caption and holding difficult, decreasing the swelling, viscosity and elasticity. For 2% samples, the longer drug release time exhibited for 2%4h sample indicates that the increase of swelling and viscosity contribute for a more sustained drug release, but the mesh size of the polymeric network seems to be determinant for the attachment of drug molecules. For the 4% samples, smaller meshes size should determine less sustained release of drug. (C) 2008 Elsevier B.V. All rights reserved.

Adherence in vitro of Candida albicans to plasma treated acrylic resin. Effect of plasma parameters, surface roughness and salivary pellicle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Constraints on four-fermion contact interactions from precise electroweak measurements

We establish constraints on a general four-fermion contact interaction from precise measurements of electroweak parameters. We compute the one-loop contribution for the leptonic Z width, anomalous magnetic, weak-magnetic, electric and weak dipole moments of leptons in order to extract bounds on the energy scale of these effective interactions.

Subtractive renormalization of one-pion-exchange and contact interactions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Characterization of micro-bubble size distribution and flow configuration in DAF contact zone by a non-intrusive image analysis system and tracer tests

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Photoacoustic procedure for measuring thermal parameters of transparent solids

An application of photoacoustic technique is developed for determining the thermal diffusivity coefficient and the thermal conductivity of transparent materials. The backing material which supports the sample is made optically opaque, i.e., it entirely absorbs the incident light, and the converted heat diffuses through the sample heating the gas in contact with its opposite surface. The method is illustrated by fitting voltage amplitude and phase signals versus the chopping frequency in the photoacoustic cell, according to a theoretical model of heat diffusion. Thermal parameters obtained for three polymers compare very well with results from the literature. (C) 1995 American Institute of Physics.

The action for the (propagating) torsion and the limits on the torsion parameters from present experimental data

Starting from the well established form of the Dirac action coupled to the electromagnetic and torsion field we find that there is some additional softly broken local symmetry associated with torsion. This symmetry fixes the form of divergences of the effective action after the spinor fields are integrated out. Then the requirement of renormalizability fixes the torsion field to be equivalent to some massive pseudovector and its action is fixed with accuracy to the values of coupling constant of torsion-spinor interaction, mass of the torsion and higher derivative terms. Implementing this action into the abelian sector of the Standard Model we establish the upper bounds on the torsion mass and coupling. In our study we used results of present experimental limits on four-fermion contact interaction (LEP, HERA, SLAC, SLD, CCFR) and TEVATRON limits on the cross section of new gauge boson, which could be produced as a resonance at high energy pp̄ collisions. © 1998 Elsevier Science B.V. All rights reserved.

Standardization of platelet parameters determination in blood samples collected with EDTA

The Abbott Cell-Dyn 3000 automated hematological analyzer prepares a histogram of platelet volume, which is measured by a technique using electrical impedance, inferring from its platelet count (PLT), mean platelet volume (MPV) and platelet distribution width (PDW). This equipment also calculates the plateletcrit (PCT). These platelet parameters may be important to evaluate platelet function, but they require standardization, because platelets swell when in contact with ethylenediaminetetra-acetic acid salts, hence an increase in blood sample storage time produces artificially increased results. To assess the effect of storage time on MPV, PLT, PDW and PCT, blood samples from 23 sickle cell anemia patients during steady state (Group I) and 50 from healthy controls (Group II) were placed in Vacutainer® tubes with dipotassium ethylenediaminetetra-acetic acid and measured over a period of 1440 minutes (24 h) at the following times: immediately after the venipuncture (time 0), 15, 30, 60, 120, 240, 360, 480 and 1440 minutes. The mean values of MPV and PCT were significantly increased (p<0.00001) along the storage time in both groups. The mean values of PLT and PDW were practically stable (p>0.05) throughout the storage time in both groups.

Environmental parameters and antimicrobial susceptibility of enterobacteriaceae isolated from estuarine waters of São Vicente, São Paulo State, Brazil

Diseases transmitted by water consists a serious public health problem and enterobacteria are the main group of microorganisms responsible for outbreaks in humans. Such pathogenic bacteria proliferate in water polluted by domestic and industrial sewage and reach the population through seawater contact. The aim of the present work was to study environmental parameters as well as to identify Enterobacteriaceae species and their antimicrobial susceptibility in water samples collected from the estuarine area of São Vicente city (São Paulo State, Brazil). Strains were identified by using traditional biochemical tests described in literature and antimicrobial susceptibility tests were carried out using the disk diffusion method. Out of 26 samples, Escherichia coli was the most frequent species (40.1%), followed by Citrobacter, Enterobacter and Klebsiella. The most effective drugs against the tested microorganisms were gentamycin, netilmicin, ciprofloxacin and cefepime. Since these bacteria are commonly found in seashore contaminated by sewage effluents, it can be concluded that estuarine waters of São Vicente are polluted and potentially capable of causing diseases and spreading pathogenic bacteria to human communities.