Advances in the analysis and design of concrete structures, metal containments and liner plate for extreme loads

The material presented in this paper summarizes the progress that has been made in the analysis, design, and testing of concrete structures. The material is summarized in the following documents: 1. Part I - Containment Design Criteria and Loading Combinations - J.D. Stevenson (Stevenson and Associates, Cleveland, Ohio, USA) 2. Part II - Reinforced and Prestressed Concrete Behavior - J. Eibl and M. Curbach (Karlsruhe University, Karlsruhe, Germany) 3. Part III - Concrete Containment Analysis, Design and Related Testing - T.E. Johnson and M.A. Daye (Bechtel Power Corporation, Gaithersburg, Maryland USA) 4. Part IV - Impact and Impulse Loading and Response Prediction - J.D. Riera (School of Engineering - UFRGS, Porto Alegre, RS, Brazil) 5. Part V - Metal Containments and Liner Plate Systems - N.J. Krutzik (Siemens AG, Offenbach Am Main, Germany) 6. Part VI - Prestressed Reactor Vessel Design, Testing and Analysis - J. Nemet (Austrian Research Center, Seibersdorf, Austria) and K.T.S. Iyengar (Indian Institute of Science, Bangalore, India).

Requirements and design of an integrated European environmental information communication system, (IEEICS)

The needs for various forms of information systems relating to the European environment and ecosystem are reviewed, and limitations indicated. Existing information systems are reviewed and compared in terms of aims and functionalities. We consider TWO technical challenges involved in attempting to develop an IEEICS. First, there is the challenge of developing an Internet-based communication system which allows fluent access to information stored in a range of distributed databases. Some of the currently available solutions are considered, i.e. Web service federations. The second main challenge arises from the fact that there is general intra-national heterogeneity in the definitions adopted, and the measurement systems used throughout the nations of Europe. Integrated strategies are needed.

Research and design challenges for developing personalised eLearning systems

While E-learning technologies are continuously developing, there are number of emerging issues and challenges that have significant impact on e-learning research and design. These include educational, technological, sociological, and psychological viewpoints. The extant literature points out that a large number of existing E-learning systems have problems with offering reusable, personalized and learner-centric content. While developers are placing emphasis on the technology aspects of e-learning, critical conceptual and pedagogical issues are often ignored. This paper will reports on our research in design and development of personalised e-learning systems and some of the challenges and issues faced.

Auslegung, Konstruktion und Fertigung von strömungsmechanischen Funktionsprototypen mittels Rapid Manufacturing

Bei der Fertigung von Funktionsbauteilen für Strömungsversuche spielt das Design und die Komplexität der Bauteilgeometrie eine wesentliche Rolle. Ziel der interdisziplinären Zusammenarbeit der Lehrstühle Strömungsmaschinen, Rechnereinsatz in der Konstruktion und Fertigungstechnik mit dem Rapid Technology Center (RTC) an der Universität Duisburg-Essen ist es, das Potenzial der additiven Fertigungsverfahren bei der Herstellung von Funktionsprototypen für strömungsmechanische Anwendungen effektiv zu nutzen. An verschiedenen, auf dieser Kooperation beruhenden, Best Practise Beispielen wird gezeigt wie das Laser-Sintern in die Prozesskette zur Herstellung von Laufrädern u. Ä. in unterschiedlichen Größenordnungen integriert werden kann. In diesem Zusammenhang werden auch die Vorüberlegungen (z. B. durch Simulation), Wechselwirkungen und Folgeprozesse, die mit dieser Fertigungstechnologie verbunden sind, aufgezeigt.

Auslegung, Konstruktion und Fertigung von strömungsmechanischen Funktionsprototypen mittels Rapid Manufacturing

Bei der Fertigung von Funktionsbauteilen für Strömungsversuche spielt das Design und die Komplexität der Bauteilgeometrie eine wesentliche Rolle. Ziel der interdisziplinären Zusammenarbeit der Lehrstühle Strömungsmaschinen, Rechnereinsatz in der Konstruktion und Fertigungstechnik mit dem Rapid Technology Center (RTC) an der Universität Duisburg-Essen ist es, das Potenzial der additiven Fertigungsverfahren bei der Herstellung von Funktionsprototypen für strömungsmechanische Anwendungen effektiv zu nutzen. An verschiedenen, auf dieser Kooperation beruhenden, Best Practise Beispielen wird gezeigt wie das Laser-Sintern in die Prozesskette zur Herstellung von Laufrädern u. Ä. in unterschiedlichen Größenordnungen integriert werden kann. In diesem Zusammenhang werden auch die Vorüberlegungen (z. B. durch Simulation), Wechselwirkungen und Folgeprozesse, die mit dieser Fertigungstechnologie verbunden sind, aufgezeigt.

Cost estimates: planning and design stages.

At head of title: Engineering and design.

Trandisciplinarity and Design: Comparative Review and Synthesis for the Design Process

Transdisciplinarity gained importance in the 1970s, with the initial signs of weakness of both multi- and interdisciplinary approaches. This weakness was felt due to the increased complexity in the social and technological landscapes. Generally, discussion over the transdisciplinary topic is centred in social and health sciences. Therefore, the major challenge in this research is to adapt design research to the emerging transdisciplinary discussion. Based on a comparative and critical review of several engineering and design models for the design process, we advocate the importance of collaboration and conceptualisation for these disciplines. Therefore, a transdisciplinary and conceptual cooperation between engineering and industrial design disciplines is considered as decisive to create breakthroughs. Furthermore, a synthesis is proposed, in order to foster the cooperation between engineering and industrial design.

Comparative study of auxetic geometrics by means of computer-aided design and engineering

Auxetic materials (or metamaterials) are those with a negative Poisson ratio (NPR) and display the unexpected property of lateral expansion when stretched, as well as an equal and opposing densification when compressed. Such geometries are being progressively employed in the development of novel products, especially in the fields of intelligent expandable actuators, shape morphing structures and minimally invasive implantable devices. Although several auxetic and potentially auxetic geometries have been summarized in previous reviews and research, precise information regarding relevant properties for design tasks is not always provided. In this study we present a comparative study of two-dimensional and three-dimensional auxetic geometries carried out by means of computer-aided design and engineering tools (from now on CAD–CAE). The first part of the study is focused on the development of a CAD library of auxetics. Once the library is developed we simulate the behavior of the different auxetic geometries and elaborate a systematic comparison, considering relevant properties of these geometries, such as Poisson ratio(s), maximum volume or area reductions attainable and equivalent Young's modulus, hoping it may provide useful information for future designs of devices based on these interesting structures.

Time Efficient Assessment and Feedback Methods for Large Computer-Aided-Design Cohorts

Timely and individualized feedback on coursework is desirable from a student perspective as it facilitates formative development and encourages reflective learning practice. Faculty however are faced with a significant and potentially time consuming challenge when teaching larger cohorts if they are to provide feedback which is timely, individualized and detailed. Additionally, for subjects which assess non-traditional submissions, such as Computer-Aided-Design (CAD), the methods for assessment and feedback tend not to be so well developed or optimized. Issues can also arise over the consistency of the feedback provided. Evaluations of Computer-Assisted feedback in other disciplines (Denton et al, 2008), (Croft et al, 2001) have shown students prefer this method of feedback to traditional “red pen” marking and also that such methods can be more time efficient for faculty.
Herein, approaches are described which make use of technology and additional software tools to speed up, simplify and automate assessment and the provision of feedback for large cohorts of first and second year engineering students studying modules where CAD files are submitted electronically. A range of automated methods are described and compared with more “manual” approaches. Specifically one method uses an application programming interface (API) to interrogate SolidWorks models and extract information into an Excel spreadsheet, which is then used to automatically send feedback emails. Another method describes the use of audio recordings made during model interrogation which reduces the amount of time while increasing the level of detail provided as feedback.
Limitations found with these methods and problems encountered are discussed along with a quantified assessment of time saving efficiencies made.

Site Controller: A System for Computer-Aided Civil Engineering and Construction

A revolution\0\0\0 in earthmoving, a $100 billion industry, can be achieved with three components: the GPS location system, sensors and computers in bulldozers, and SITE CONTROLLER, a central computer system that maintains design data and directs operations. The first two components are widely available; I built SITE CONTROLLER to complete the triangle and describe it here. SITE CONTROLLER assists civil engineers in the design, estimation, and construction of earthworks, including hazardous waste site remediation. The core of SITE CONTROLLER is a site modelling system that represents existing and prospective terrain shapes, roads, hydrology, etc. Around this core are analysis, simulation, and vehicle control tools. Integrating these modules into one program enables civil engineers and contractors to use a single interface and database throughout the life of a project.

Computer aided design and finite element modeling to predict bulk mechanical properties of bone scaffolds using triply periodic minimal surfaces (progettazione assistita al calcolatore ed analisi con il metodo degli elementi finiti per predire il comportamento meccanico di scaffolds ossei creati con l'uso di superfici minime periodiche in tre direzioni)

The aim of Tissue Engineering is to develop biological substitutes that will restore lost morphological and functional features of diseased or damaged portions of organs. Recently computer-aided technology has received considerable attention in the area of tissue engineering and the advance of additive manufacture (AM) techniques has significantly improved control over the pore network architecture of tissue engineering scaffolds. To regenerate tissues more efficiently, an ideal scaffold should have appropriate porosity and pore structure. More sophisticated porous configurations with higher architectures of the pore network and scaffolding structures that mimic the intricate architecture and complexity of native organs and tissues are then required. This study adopts a macro-structural shape design approach to the production of open porous materials (Titanium foams), which utilizes spatial periodicity as a simple way to generate the models. From among various pore architectures which have been studied, this work simulated pore structure by triply-periodic minimal surfaces (TPMS) for the construction of tissue engineering scaffolds. TPMS are shown to be a versatile source of biomorphic scaffold design. A set of tissue scaffolds using the TPMS-based unit cell libraries was designed. TPMS-based Titanium foams were meant to be printed three dimensional with the relative predicted geometry, microstructure and consequently mechanical properties. Trough a finite element analysis (FEA) the mechanical properties of the designed scaffolds were determined in compression and analyzed in terms of their porosity and assemblies of unit cells. The purpose of this work was to investigate the mechanical performance of TPMS models trying to understand the best compromise between mechanical and geometrical requirements of the scaffolds. The intention was to predict the structural modulus in open porous materials via structural design of interconnected three-dimensional lattices, hence optimising geometrical properties. With the aid of FEA results, it is expected that the effective mechanical properties for the TPMS-based scaffold units can be used to design optimized scaffolds for tissue engineering applications. Regardless of the influence of fabrication method, it is desirable to calculate scaffold properties so that the effect of these properties on tissue regeneration may be better understood.

Computer Aided Surgery for Percutaneous Nephrolithotomy: Clinical Requirement Analysis and System Design

Percutaneous nephrolithotomy (PCNL) for the treatment of renal stones and other related renal diseases has proved its efficacy and has stood the test of time compared with open surgical methods and extracorporal shock wave lithotripsy. However, access to the collecting system of the kidney is not easy because the available intra-operative image modalities only provide a two dimensional view of the surgical scenario. With this lack of visual information, several punctures are often necessary which, increases the risk of renal bleeding, splanchnic, vascular or pulmonary injury, or damage to the collecting system which sometimes makes the continuation of the procedure impossible. In order to address this problem, this paper proposes a workflow for introduction of a stereotactic needle guidance system for PCNL procedures. An analysis of the imposed clinical requirements, and a instrument guidance approach to provide the physician with a more intuitive planning and visual guidance to access the collecting system of the kidney are presented.

Engineering design handbook : computer aided design of mechanical systems.

Cover title.