Hydraulics for small fishing trawlers

Fishing vessels where electric power supply from alternator is available to operate various auxiliaries located anywhere in the vessel, the small crafts, which constitute over 95% of the total fishing crafts operating in India, are entirely dependent on one source of power, i. e. the main diesel engine. To utilize this source of motive power to operate the winches and other auxiliaries, mechanical drive involving shafts, bearings and pulleys, is inconvenient. This paper presents basic advantages of hydraulic system over mechanical drive.

Fibre optic monitoring of a deep circular excavation

This paper describes part of the monitoring undertaken at Abbey Mills shaft F, one of the main shafts of Thames Water's Lee tunnel project in London, UK. This shaft, with an external diameter of 30 m and 73 m deep, is one of the largest ever constructed in the UK and consequently penetrates layered and challenging ground conditions (Terrace Gravel, London Clay, Lambeth Group, Thanet Sand Formation, Chalk Formation). Three out of the twenty 1-2 m thick and 84 m deep diaphragm wall panels were equipped with fibre optic instrumentation. Bending and circumferential hoop strains were measured using Brillouin optical time-domain reflectometry and analysis technologies. These measurements showed that the overall radial movement of the wall was very small. Prior to excavation during a dewatering trial, the shaft may have experienced three-dimensional deformation due to differential water pressures. During excavation, the measured hoop and bending strains of the wall in the chalk exceeded the predictions. This appears to be related to the verticality tolerances of the diaphragm wall and lower circumferential hoop stiffness of the diaphragm walls at deep depths. The findings from this case study provide valuable information for future deep shafts in London. © ICE Publishing: All rights reserved.

Research progress on algae of the microbial crusts in and and semiarid regions

Microbial crusts are attracting much interest in view of their possible uses in environmental conservation and ecological restoration of the and and semiarid regions. Because algae play an irreplaceable important role in the early formation and the strengthening of microbial crusts, they are paid much more attention to than other cryptogams. In this paper, an overview of the current knowledge on the fine structure and development of microbial crust, focusing on the algal biomass, vertical distribution, succession, influential factors on algae, cohesion of soil stabilization, cementing mechanism for soil particles and the microalgal extracellular polymers is given, with particular emphasis on the authors' researches, and some prospects are put forward as well.

基于激光熔覆的绿色再制造技术研究

为了实现轴类零件的修复,搭建基于激光熔覆技术的绿色再制造系统,该系统由功率为6kW的CO2激光器、四轴工作台、送粉机构、数控系统等硬件设备和激光绿色再制造系统驱动软件组成。以轴类为典型零件、Ni60A合金粉末为熔覆材料,对激光绿色再制造工艺技术进行研究。通过研究分析激光功率、熔覆速度、送粉量、熔覆间距等主要参数对熔覆层高度、宽度和熔覆层质量等的影响情况,获得了轴类零件激光修复的最佳工艺参数组合,实现基于激光熔覆的绿色再制造技术在生产实践中的应用。

砂泥岩储层测井产能预测方法研究

Productivity prediction is very important in the exploration and development of oilfields. Using well log data to predict productivity is a front-line technology， which is key issue in petroleum exploration phase. The essential factors of productivity prediction is building practical models and correcting various causes to improve precision of prediction parameters. Any errors of parameters selections can affect the calculation of productivity prediction; therefore， how to improve research means and calculation accuracy is an important task of productivity prediction. Theory and case examples are deeply and comprehensively studied in the paper. Based on the theory of mud-filtrate invasion and experimental results， the damage of drilling， cementing， perforating，acidizing and fracturing were investigated. The damage depth was quantitatively evaluated by log data， based on this， the processing results of reservoir sensitivity were used to analysis quantitatively the damage of reservoir. The productivity prediction and reservoir damage were initiatively incorporated according to well logging， and the precision of productivity prediction was effectively improved. The method of NMR was explored to calculate the fluid viscosity on the basis of reservoir physical method， and the differences between the two methods were compared in the paper. From the theory fluid flow in porous media， various of theoretical models of production prediction were explored and several practical models were consided， such as productivity index method， improved productivity index method， improved Bearder method， SVM and so on. The characteristic and the application scope of these methods were studied. The inflow productivity and outflow productivity were incorporated and nodal analysis method was used to forecast wellhead yield， thus achieved scientifically production. On the applied background of conventional logging suite， the applying of special items or new logging method which is practical in the research area were studied， the logging suite was further optimized， and the precision of forecast was improved. On the basis of the modeling and the calculation of parameters， these methods were verified and analyzed， and the reconstruct principle was also built for block reservoir. The research block was processed by these methods and compared with testing data. Based on above the research， a technological system which is practical for shaly sand profiles in Shengli Oilfield was built. The system can reach commercialized degree，and satisfied the need of exploration and development of the oilfield.

三塘湖盆地牛圈湖区储层特征研究—以齐古组、头屯河组为例

In view of few researches into pore textures and anisotropy characteristics of Qiguzu-toutunhezu reservoir in Niuquanhu block in Santanghu Basin, in order to enhance the hydrocarbon recovery of the region of interest and improve the reservoir development effect, with the employment of the experiments like cast thin slice, scanning electron microscope, conventional high pressure mercury penetration, constant speed mercury penetration and nuclear magnetic resonance, the thesis makes a thorough research into pore texture characteristics and anisotropy characteristics of the sandstone reservoir. The research shows that the microscopic pore textures are complicated, the anisotropy is high and waterflood development water/oil displacement efficiency is low, which are mainly caused by the high microscopic anisotropy of the reservoir. Specially, the research shows that Qiguzu-toutunhezu reservoir belongs to braided delta front intrafacies, the intergranular pore is the main type of pores, which take up 65.50 percent of total pores, intergranular dissolved pores, feldspar dissolved pores and lithic dissolved pores are on the second place, and there are few carbonate dissolved pores. The reservoir belongs to mesopore-fine throat and mesopore-medium throat. The pore distribution of the sandstone reservoir is comparatively centralized. The reservoir inhomogeneity is mainly caused by the throat inhomogeneity. Diagenesis mainly includes compaction, cementation, metasomatism and dissolution. Compared with compaction， cementation exerts more direct impact on the decline of the porosity of the sandstone reservoir ( pore loss factor is 63.75 percent in the cementing process). Based on the classification of diagenetic stages, the reservoir diagenesis is on the stage of the late period of early diagenetic stage to early period of late diagenetic stage. The study area of the small sandstone reservoir layer of the anisotropy of the relatively strong; plane, the anisotropy of the relatively weak. microscopic anisotropy of its relatively strong.

孤北洼陷沙三-沙四段隐蔽油藏形成机制及其预测

Based on the study of sequence stratigraphy, modern sedimentary, basin analysis, and petroleum system in Gubei depression, this paper builds high resolution sequence stratigraphic structure, sedimentary system, sandbody distribution, the effect of tectonic in sequence and sedimentary system evolution and model of tectonic-lithofacies. The pool formation mechanism of subtle trap is developed. There are some conclusions and views as follows. 1.With the synthetic sequence analysis of drilling, seismic, and well log, the highly resolution sequence structure is build in Gubei depression. They are divided two secondary sequences and seven three-order sequences in Shahejie formation. They are include 4 kinds of system traces and 7 kinds of sedimentary systems which are alluvial fan, under water fan, alluvial fan and fan-delta, fan-delta, lacustrine-fan, fluvial-delta-turbidite, lakeshore beach and bar, and deep lake system. Sandbody distribution is show base on third order sequence. 2.Based on a lot of experiment and well log, it is point out that there are many types of pore in reservoir with the styles of corrosion pore, weak cementing, matrix cementing, impure filling, and 7 kinds of diagenetic facies. These reservoirs are evaluated by lateral and profile characteristics of diagenetic facies and reservoir properties. 3.The effect of simultaneous faulting on sediment process is analyzed from abrupt slope, gentle slope, and hollow zone. The 4 kinds of tectonic lithofacies models are developed in several periods in Gubei depression; the regional distribution of subtle trap is predicted by hydro accumulation characteristics of different tectonic lithofacies. 4.There are 4 types of compacting process, which are normal compaction, abnormal high pressure, abnormal low pressure and complex abnormal pressure. The domain type is normal compaction that locates any area of depression, but normal high pressure is located only deep hollow zone (depth more than 3000m), abnormal low pressures are located gentle slope and faulted abrupt slope (depth between 1200~2500m). 5.Two types dynamic systems of pool formation (enclosed and partly enclosed system) are recognized. They are composed by which source rocks are from Es3 and Es4, cap rocks are deep lacustrine shale of Esl and Es3, and sandstone reservoirs are 7 kinds of sedimentary system in Es3 and Es4. According to theory of petroleum system, two petroleum systems are divided in Es3 and Es4 of Gubei depression, which are high or normal pressure self-source system and normal or low pressure external-source system. 6.There are 3 kinds of combination model of pool formation, the first is litholgical pool of inner depression (high or normal pressure self-source type), the second is fault block or fault nose pool in marginal of depression (normal type), the third is fault block-lithological pool of central low lifted block (high or normal pressure type). The lithological pool is located central of depression, other pool are located gentle or abrupt slope that are controlled by lithological, faulting, unconfirmed. 7.This paper raise a new technique and process of exploration subtle trap which include geological modeling, coring description and logging recognition, and well log constrained inversion. These are composed to method and theory of predicting subtle trap. Application these methods and techniques, 6 hydro objects are predicted in three zone of depression.

Reabilitação fixa aparafusada Vs. reabilitação fixa cimentada

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Medicina Dentária

Cement-in-cement revision hip arthroplasty: an analysis of clinical and biomechanical literature

Introduction The number of revision hip arthroplasties is increasing but several aspects of this procedure could be improved. One method of reducing intra-operative complications is the cement-in-cement technique. This procedure entails cementing a smaller femoral prosthesis into the existing stable cement mantle. The aim of this systematic review is to provide a concise overview of the existing historical, operative, biomechanical and clinical literature on the cement-in-cement construct.

Changing climate, changing process: implications for salt transportation and weathering within building sandstones in the UK

Salt weathering is a crucial process that brings about a change in stone, from the scale of landscapes to stone outcrops and natural building stone facades. It is acknowledged that salt weathering is controlled by fluctuations in temperature and moisture, where repeated oscillations in these parameters can cause re-crystallisation, hydration/de-hydration of salts, bringing about stone surface loss in the form of, for example, granular disaggregation, scaling, and multiple flaking. However, this ‘traditional’ view of how salt weathering proceeds may need to be re-evaluated in the light of current and future climatic trends. Indeed, there is considerable scope for the investigation of consequences of climate change on geomorphological processes in general. Building on contemporary research on the ‘deep wetting’ of natural building stones, it is proposed that (as stone may be wetter for longer), ion diffusion may become a more prominent mechanism for the mixing of molecular constituents, and a shift in focus from physical damage to chemical change is suggested. Data from ion diffusion cell experiments are presented for three different sandstone types, demonstrating that salts may diffuse through porous stone relatively rapidly (in comparison to, for example, dense concrete). Pore water from stones undergoing diffusion experiments was extracted and analysed. Factors controlling ion diffusion
relating to ‘time of wetness’ within stones are discussed, (continued saturation, connectivity of pores, mineralogy, behaviour of salts, sedimentary structure), and potential changes in system dynamics as a result of climate change are addressed. System inputs may change in terms of increased moisture input, translating into a greater depth of wetting front. Salts are likely to be ‘stored’ differently in stones, with salt being in solution for longer periods (during prolonged winter wetness). This has myriad implications in terms of the movement of ions by diffusion and the potential for chemical change in the stone (especially in more mobile constituents), leading to a weakening of the stone matrix/grain boundary cementing. The ‘output’ may be mobilisation and precipitation of elements leading to, for example, uneven cementing in the stone. This reduced strength of the stone, or compromised ability of the stone to absorb stress, is likely to make crystallisation a more efficacious mechanism of decay when it does occur. Thus, a delay in the onset of crystallisation while stonework is wet does not preclude exaggerated or accelerated material loss when it finally happens.

Effect of the crown design and interface lute parameters on the stress-state of a machined crown-tooth system: A finite element analysis

The effect of preparation design and the physical properties of the interface lute on the restored machined ceramic crown-tooth complex are poorly understood. The aim of this work was to determine, by means of three-dimensional finite element analysis (3D FEA) the effect of the tooth preparation design and the elastic modulus of the cement on the stress state of the cemented machined ceramic crown-tooth complex. The three-dimensional structure of human premolar teeth, restored with adhesively cemented machined ceramic crowns, was digitized with a micro-CT scanner. An accurate, high resolution, digital replica model of a restored tooth was created. Two preparation designs, with different occlusal morphologies, were modeled with cements of 3 different elastic moduli. Interactive medical image processing software (mimics and professional CAD modeling software) was used to create sophisticated digital models that included the supporting structures; periodontal ligament and alveolar bone. The generated models were imported into an FEA software program (hypermesh version 10.0, Altair Engineering Inc.) with all degrees of freedom constrained at the outer surface of the supporting cortical bone of the crown-tooth complex. Five different elastic moduli values were given to the adhesive cement interface 1.8 GPa, 4 GPa, 8 GPa, 18.3 GPa and 40 GPa; the four lower values are representative of currently used cementing lutes and 40 GPa is set as an extreme high value. The stress distribution under simulated applied loads was determined. The preparation design demonstrated an effect on the stress state of the restored tooth system. The cement elastic modulus affected the stress state in the cement and dentin structures but not in the crown, the pulp, the periodontal ligament or the cancellous and cortical bone. The results of this study suggest that both the choice of the preparation design and the cement elastic modulus can affect the stress state within the restored crown-tooth complex.

Consociationalism, regional integration and vote choice

Consociational institutional arrangements in deeply divided societies are often criticised for cementing the underlying conflict cleavage, encouraging the continued dominance of conflict-based party competition and voter behaviour and prohibiting the emergence of 'normal' (that is, non-conflict-based) dimensions of political competition. However, drawing on evidence from a post-election survey at the 2009 Northern Ireland election to the European Parliament, I find that EU issues determined intra-bloc vote choice (at least in the nationalist community). This suggests that there is potential for regional integration projects, such as the EU, to contribute to the normalisation of politics in a consociational system by acting as the source of an externally generated dimension of political competition. © 2012 Macmillan Publishers Ltd.

Composite hunting technologies from the Terminal Pleistocene and Early Holocene, Niah Cave, Borneo

Renewed archaeological investigation of the West Mouth of Niah Cave, Borneo has demonstrated that even within lowland equatorial environments depositional conditions do exist where organic remains of late glacial and early post-glacial age can be preserved. Excavations by the Niah Cave Research Project (NCP) (2000-2003) towards the rear of the archaeological reserve produced several bone points and worked stingray spines, which exhibit evidence of hafting mastic and fibrous binding still adhering to their shafts. The position of both gives strong indication of how these cartilaginous points were hafted and gives insight into their potential function. These artefacts were recovered from secure and (14)C dated stratigraphic horizons. The results of this study have implications for our understanding the function of the Terminal Pleistocene and Early Holocene bone tools recovered from other regions of Island Southeast Asia. They demonstrate that by the end the Pleistocene rainforest foragers in Borneo were producing composite technologies that probably included fishing leisters and potentially the bow and arrow. (C) 2009 Elsevier Ltd. All rights reserved.

Análise do comportamento de polímeros na estabilização de solos em fundações

O presente projeto de investigação em Engenharia Civil é construído em torno das necessidades atuais expressas pelos setores da construção e obras públicas em fundações. Em colaboração com a empresa GEO este trabalho pretende dar resposta em tempo útil aos empreiteiros, pondo o conhecimento científico ao serviço da indústria, colmatando a escassez de investigação académica que se verifica neste domínio. Esta investigação, à qual se associou a empresa BRASFOND, recorre ao estudo de ensaios de carga estática à compressão realizados no Brasil, segundo a NBR 12131 (2005) e NBR 12131 (2006). Assim, para estudar o desempenho de polímeros aplicados na estabilização de solos em fundações, foram analisados 6 ensaios de carga realizados em obras de intervenção da empresa GEO, disponibilizados pela empresa BRASFOND. Os ensaios de carga verticais estáticos de compressão axial foram realizados em estacas de 3 obras, nomeadamente a construção de uma central termoelétrica, em 2009, e de dois edifícios, em 2010. O projeto de fundações da central termoelétrica assentou na execução de estacas com polímeros, com 1270 estacas moldadas “in loco” com 1 000 mm de diâmetro e profundidade variável de 10 m a 18 m, em solos moles e pouco compactos de 8 m a 9 m de espessura, encastradas até 3 m sobre um maciço Gnaisse medianamente alterado (W3). Dos ensaios de carga realizados nesta obra, foram alvo deste estudo a análise dos primeiros 4 disponibilizados pela empresa. Os valores estimados por métodos semi-empíricos da capacidade resistente das estacas, considerando a recuperação da rocha nos trechos encastrados, foram comparados com a carga resistente última à compressão obtida através do ensaio de carga. O projeto de fundações de dois edifícios de elevado número de andares (cerca de 30) no litoral do Estado de São Paulo, em Santos, assentou na execução de fundações indiretas em solos moles a muito moles, com estacas de grandes dimensões moldadas com recurso a polímeros. Para atestar a qualidade das estacas, de forma a avaliar o comportamento carga versus assentamento e estimar as características da capacidade de carga, procedeu-se à execução de dois ensaios de carga estática à compressão, um dos quais instrumentado em profundidade. Os valores estimados por métodos semi-empíricos da capacidade resistente das estacas foram comparados com a carga resistente última à compressão obtida através do ensaio de carga. Para além deste estudo se revestir de interesse académico e empresarial, o contexto inerente à aplicação de polímeros em fundações é relevante para a prática pedagógica. Assim, este projeto envolve também uma componente educacional, esta última implementada numa escola do ensino básico e secundário da região centro do país.