Crucible of America.

Mode of access: Internet.

Report of highway research at Pittsburg, California, 1921 and 1922.

Test commenced by the Columbia steel company, finished with the financial cooperation of the California highway commission and U.S. Bureau of public roads.

Report on the Blackwell's Island bridge (Queensboro bridge).

Mode of access: Internet.

Your land : a handbook of practical methods for preventing and curing soil erosion.

"A compilation of practical tried-and-proved methods which have been developed by state agricultural colleges and extension workers, U.S. soil conservation experts, and county agricultural agents."--p. [2] of cover.

The work situation and class position of Brazilian engineers

This thesis analyses the work situation and class position of Brazilian engineers through a Marxist perspective. The research is based on two case studies, one focused on a large German steel company based in Brazil and the other on a large Brazilian energy corporation. The fieldwork involved 114 interviews, with engineers from different hierarchical positions in these two companies. Data was also gathered through interviews with representatives from the companies, the Council of Engineering, the Engineering Education System and the Engineers Trade Unions. The findings show that the engineering profession in Brazil has shifted from its initial condition as a liberal profession to an organizational profession, with the country's industrial deployment. Both companies consider all salaried workers as employees, including managers. Hence they are subject to the company's general personnel policies. The multinational company controls labour more rigidly than the national company, as well as reserving its top positions for its home country's executives. Although no deskilling process was found, engineers of both companies performed simple work, which required less engineering knowledge than they had learned from school. Engineers have little autonomy, authority and participation in decision making and are subject to direct supervision, performance evaluation, time control, overtime work, productivity and to poor working conditions in the multinational company. The majority of the engineers supervised other workers without being in a managerial position. They found that to move into management, was a good way to improve their autonomy, authority, prestige, salary, status, power and professional pride. Despite ideological divisions between capital and labour, most of the engineers were unionised and saw unions as the right way to deal with the employer.

United States of America before the National Labor Relations Board, Case C-142 : in the matter of United States Steel Corporation (a New Jersey Corporation), Carnegie-Illinois Steel Corporation (a New Jersey Corporation) and Steel Workers Organizing Committee and Amalgamated Association of Iron, Steel and Tin Workers of North America.

"Exihibit B. Plans of employmee representation in effect at the plants of respondent, Carnegie-Illinois Steel Corporation"--Cover.

Hoover Steel Ball Company Plant, Ann Arbor, Michigan

Image from publication: The evolution of the steel ball industry. Hoover Steel Ball Company (Ann Arbor, Mich.), [1917]

Metal artifacts from titanium and steel screws in CT, 1.5T and 3T MR images of the tibial Pilon: A quantitative assessment in 3D

Radiographs are commonly used to assess articular reduction of the distal tibia (pilon) fractures postoperatively, but may reveal malreductions inaccurately. While Magnetic Resonance Imaging (MRI) and Computed Tomography (CT) are potential 3D alternatives they generate metal-related artifacts. This study aims to quantify the artifact size from orthopaedic screws using CT, 1.5T and 3T MRI data. Three screws were inserted into one intact human cadaver ankle specimen proximal to and along the distal articular surface, then CT, 1.5T and 3T MRI scanned. Four types of screws were investigated: titanium alloy (TA), stainless steel (SS) (Ø = 3.5 mm), cannulated TA (CTA) and cannulated SS (CSS)(Ø = 4.0 mm, Ø empty core = 2.6 mm). 3D artifact models were reconstructed using adaptive thresholding. The artifact size was measured by calculating the perpendicular distance from the central screw axis to the boundary of the artifact in four anatomical directions with respect to the distal tibia. The artifact sizes (in the order of TA, SS, CTA and CSS) from CT were 2.0 mm, 2.6 mm, 1.6 mm and 2.0 mm; from 1.5T MRI they were 3.7 mm, 10.9 mm, 2.9 mm, and 9 mm; and 3T MRI they were 4.4 mm, 15.3 mm, 3.8 mm, and 11.6 mm respectively. Therefore, CT can be used as long as the screws are at a safe distance of about 2 mm from the articular surface. MRI can be used if the screws are at least 3 mm away from the articular surface except SS and CSS. Artifacts from steel screws were too large thus obstructed the pilon from being visualised in MRI. Significant differences (P < 0.05) were found in the size of artifacts between all imaging modalities, screw types and material types, except 1.5T versus 3T MRI for the SS screws (P = 0.063). CTA screws near the joint surface can improve postoperative assessment in CT and MRI. MRI presents a favourable non-ionising alternative when using titanium hardware. Since these factors may influence the quality of postoperative assessment, potential improvements in operative techniques should be considered.

Ultimate compressive strength of cold-formed steel angle struts loaded through a single bolt

This paper presents design recommendations for the strength of cold-formed steel angle structs. The work was part funded by the Carnegie Trust and is co-authored by academics from Hong-Kong University. The work has led to a collaboration with the University of Malaya, attempting to predict the strength using artificial neural networks.

Niagara Falls Suspension Bridge Company fonds, 1875-1876, 1878, 1884

In 1846, the governments of Upper Canada and the State of New York initiated the creation of two companies that would be authorized to build a bridge over the Niagara River. The bridge was to be owned by both companies, respectively known as the Niagara Falls Suspension Bridge Company (Canadian) and the International Bridge Company (American). A suspension bridge was completed in 1848. This bridge was later replaced by a second suspension bridge that accommodated railways, built in 1853-54. However, the increasing weight of trains made it necessary for the bridge to be redesigned, and a third bridge was completed in 1886. Eventually, this bridge was replaced by a steel arch bridge, which was completed in 1897.

Iron, steel and other alloys

UANL

An emergy-based evaluation of a reverse logistics network for steel recycling

Efficient implementation of recycling networks requires appropriate logistical structures for managing the reverse flow of materials from users to producers. The steel sheet distributor studied had established a protocol for scrap recovery with the steel plant and its customers. The company invested in producing containers, hiring a specialized labor force and in purchasing trucks for container transportation to implement the logistics network for recycling. That network interconnected the company with two kinds of customers: the ones returning scrap and the ones who preferred to continue business-as-usual. The logistical network was analyzed using emergy synthesis, and the data obtained were used to evaluate and compare the system's environmental costs and benefits from the perspective of the distributor and the steel plant operator. The use of emergy ternary diagrams provided a way to assess recycle strategies to compare the relative economic and environmental benefits of the logistical network implemented. The minimum quantity of scrap that the distributor must recover to improve environmental benefits was determined allowing decision on whether it is worth keeping the system running. The new assessment method proposed also may help policy-makers to create strategies to reward or incentive users of reverse logistics, and help to establish regulations, by decreasing taxes or stimulating innovation, for effectively implement the National Policy on Solid Waste. (C) 2013 Elsevier Ltd. All rights reserved.

Corrosion studies on 304 stainless steel containing one percent boron-10 /

"U.S. Atomic Energy Commission Contract AT(29-1)-1106."