Implementação e avaliação do protocolo μTESLA: proposta de uso nas redes veiculares

Pós-graduação em Ciência da Computação - IBILCE

Sistemi riconfigurabili a basso consumo per applicazioni di monitoraggio distribuito

The term Ambient Intelligence (AmI) refers to a vision on the future of the information society where smart, electronic environment are sensitive and responsive to the presence of people and their activities (Context awareness). In an ambient intelligence world, devices work in concert to support people in carrying out their everyday life activities, tasks and rituals in an easy, natural way using information and intelligence that is hidden in the network connecting these devices. This promotes the creation of pervasive environments improving the quality of life of the occupants and enhancing the human experience. AmI stems from the convergence of three key technologies: ubiquitous computing, ubiquitous communication and natural interfaces. Ambient intelligent systems are heterogeneous and require an excellent cooperation between several hardware/software technologies and disciplines, including signal processing, networking and protocols, embedded systems, information management, and distributed algorithms. Since a large amount of fixed and mobile sensors embedded is deployed into the environment, the Wireless Sensor Networks is one of the most relevant enabling technologies for AmI. WSN are complex systems made up of a number of sensor nodes which can be deployed in a target area to sense physical phenomena and communicate with other nodes and base stations. These simple devices typically embed a low power computational unit (microcontrollers, FPGAs etc.), a wireless communication unit, one or more sensors and a some form of energy supply (either batteries or energy scavenger modules). WNS promises of revolutionizing the interactions between the real physical worlds and human beings. Low-cost, low-computational power, low energy consumption and small size are characteristics that must be taken into consideration when designing and dealing with WSNs. To fully exploit the potential of distributed sensing approaches, a set of challengesmust be addressed. Sensor nodes are inherently resource-constrained systems with very low power consumption and small size requirements which enables than to reduce the interference on the physical phenomena sensed and to allow easy and low-cost deployment. They have limited processing speed,storage capacity and communication bandwidth that must be efficiently used to increase the degree of local ”understanding” of the observed phenomena. A particular case of sensor nodes are video sensors. This topic holds strong interest for a wide range of contexts such as military, security, robotics and most recently consumer applications. Vision sensors are extremely effective for medium to long-range sensing because vision provides rich information to human operators. However, image sensors generate a huge amount of data, whichmust be heavily processed before it is transmitted due to the scarce bandwidth capability of radio interfaces. In particular, in video-surveillance, it has been shown that source-side compression is mandatory due to limited bandwidth and delay constraints. Moreover, there is an ample opportunity for performing higher-level processing functions, such as object recognition that has the potential to drastically reduce the required bandwidth (e.g. by transmitting compressed images only when something ‘interesting‘ is detected). The energy cost of image processing must however be carefully minimized. Imaging could play and plays an important role in sensing devices for ambient intelligence. Computer vision can for instance be used for recognising persons and objects and recognising behaviour such as illness and rioting. Having a wireless camera as a camera mote opens the way for distributed scene analysis. More eyes see more than one and a camera system that can observe a scene from multiple directions would be able to overcome occlusion problems and could describe objects in their true 3D appearance. In real-time, these approaches are a recently opened field of research. In this thesis we pay attention to the realities of hardware/software technologies and the design needed to realize systems for distributed monitoring, attempting to propose solutions on open issues and filling the gap between AmI scenarios and hardware reality. The physical implementation of an individual wireless node is constrained by three important metrics which are outlined below. Despite that the design of the sensor network and its sensor nodes is strictly application dependent, a number of constraints should almost always be considered. Among them: • Small form factor to reduce nodes intrusiveness. • Low power consumption to reduce battery size and to extend nodes lifetime. • Low cost for a widespread diffusion. These limitations typically result in the adoption of low power, low cost devices such as low powermicrocontrollers with few kilobytes of RAMand tenth of kilobytes of program memory with whomonly simple data processing algorithms can be implemented. However the overall computational power of the WNS can be very large since the network presents a high degree of parallelism that can be exploited through the adoption of ad-hoc techniques. Furthermore through the fusion of information from the dense mesh of sensors even complex phenomena can be monitored. In this dissertation we present our results in building several AmI applications suitable for a WSN implementation. The work can be divided into two main areas:Low Power Video Sensor Node and Video Processing Alghoritm and Multimodal Surveillance . Low Power Video Sensor Nodes and Video Processing Alghoritms In comparison to scalar sensors, such as temperature, pressure, humidity, velocity, and acceleration sensors, vision sensors generate much higher bandwidth data due to the two-dimensional nature of their pixel array. We have tackled all the constraints listed above and have proposed solutions to overcome the current WSNlimits for Video sensor node. We have designed and developed wireless video sensor nodes focusing on the small size and the flexibility of reuse in different applications. The video nodes target a different design point: the portability (on-board power supply, wireless communication), a scanty power budget (500mW),while still providing a prominent level of intelligence, namely sophisticated classification algorithmand high level of reconfigurability. We developed two different video sensor node: The device architecture of the first one is based on a low-cost low-power FPGA+microcontroller system-on-chip. The second one is based on ARM9 processor. Both systems designed within the above mentioned power envelope could operate in a continuous fashion with Li-Polymer battery pack and solar panel. Novel low power low cost video sensor nodes which, in contrast to sensors that just watch the world, are capable of comprehending the perceived information in order to interpret it locally, are presented. Featuring such intelligence, these nodes would be able to cope with such tasks as recognition of unattended bags in airports, persons carrying potentially dangerous objects, etc.,which normally require a human operator. Vision algorithms for object detection, acquisition like human detection with Support Vector Machine (SVM) classification and abandoned/removed object detection are implemented, described and illustrated on real world data. Multimodal surveillance: In several setup the use of wired video cameras may not be possible. For this reason building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. Energy efficiency for wireless smart camera networks is one of the major efforts in distributed monitoring and surveillance community. For this reason, building an energy efficient wireless vision network for monitoring and surveillance is one of the major efforts in the sensor network community. The Pyroelectric Infra-Red (PIR) sensors have been used to extend the lifetime of a solar-powered video sensor node by providing an energy level dependent trigger to the video camera and the wireless module. Such approach has shown to be able to extend node lifetime and possibly result in continuous operation of the node.Being low-cost, passive (thus low-power) and presenting a limited form factor, PIR sensors are well suited for WSN applications. Moreover techniques to have aggressive power management policies are essential for achieving long-termoperating on standalone distributed cameras needed to improve the power consumption. We have used an adaptive controller like Model Predictive Control (MPC) to help the system to improve the performances outperforming naive power management policies.

Implementazione su fpga di un pre-distorsore digitale a banda larga per sistemi a microonde di backhaul

The development of next generation microwave technology for backhauling systems is driven by an increasing capacity demand. In order to provide higher data rates and throughputs over a point-to-point link, a cost-effective performance improvement is enabled by an enhanced energy-efficiency of the transmit power amplification stage, whereas a combination of spectrally efficient modulation formats and wider bandwidths is supported by amplifiers that fulfil strict constraints in terms of linearity. An optimal trade-off between these conflicting requirements can be achieved by resorting to flexible digital signal processing techniques at baseband. In such a scenario, the adaptive digital pre-distortion is a well-known linearization method, that comes up to be a potentially widely-used solution since it can be easily integrated into base stations. Its operation can effectively compensate for the inter-modulation distortion introduced by the power amplifier, keeping up with the frequency-dependent time-varying behaviour of the relative nonlinear characteristic. In particular, the impact of the memory effects become more relevant and their equalisation become more challenging as the input discrete signal feature a wider bandwidth and a faster envelope to pre-distort. This thesis project involves the research, design and simulation a pre-distorter implementation at RTL based on a novel polyphase architecture, which makes it capable of operating over very wideband signals at a sampling rate that complies with the actual available clock speed of current digital devices. The motivation behind this structure is to carry out a feasible pre-distortion for the multi-band spectrally efficient complex signals carrying multiple channels that are going to be transmitted in near future high capacity and reliability microwave backhaul links.

A model for radiofrequency electromagnetic field predictions at outdoor and indoor locations in the context of epidemiological research

We present a geospatial model to predict the radiofrequency electromagnetic field from fixed site transmitters for use in epidemiological exposure assessment. The proposed model extends an existing model toward the prediction of indoor exposure, that is, at the homes of potential study participants. The model is based on accurate operation parameters of all stationary transmitters of mobile communication base stations, and radio broadcast and television transmitters for an extended urban and suburban region in the Basel area (Switzerland). The model was evaluated by calculating Spearman rank correlations and weighted Cohen's kappa (kappa) statistics between the model predictions and measurements obtained at street level, in the homes of volunteers, and in front of the windows of these homes. The correlation coefficients of the numerical predictions with street level measurements were 0.64, with indoor measurements 0.66, and with window measurements 0.67. The kappa coefficients were 0.48 (95%-confidence interval: 0.35-0.61) for street level measurements, 0.44 (95%-CI: 0.32-0.57) for indoor measurements, and 0.53 (95%-CI: 0.42-0.65) for window measurements. Although the modeling of shielding effects by walls and roofs requires considerable simplifications of a complex environment, we found a comparable accuracy of the model for indoor and outdoor points.

Using Micro-Gravity Techniques to Map Alluvium Thickness and Pleistocene Location of the West Branch of the Susquehanna River Near Muncy, Pennsylvania

Laurentide glaciation during the early Pleistocene (~970 ka) dammed the southeast-flowing West Branch of the Susquehanna River (WBSR), scouring bedrock and creating 100-km-long glacial Lake Lesley near the Great Bend at Muncy, Pennsylvania (Ramage et al., 1998). Local drill logs and well data indicate that subsequent paleo-outwash floods and modern fluvial processes have deposited as much as 30 meters of alluvium in this area, but little is known about the valley fill architecture and the bedrock-alluvium interface. By gaining a greater understanding of the bedrock-alluvium interface the project will not only supplement existing depth to bedrock information, but also provide information pertinent to the evolution of the Muncy Valley landscape. This project determined if variations in the thickness of the valley fill were detectable using micro-gravity techniques to map the bedrock-alluvium interface. The gravity method was deemed appropriate due to scale of the study area (~30 km2), ease of operation by a single person, and the available geophysical equipment. A LaCoste and Romberg Gravitron unit was used to collect gravitational field readings at 49 locations over 5 transects across the Muncy Creek and Susquehanna River valleys (approximately 30 km2), with at least two gravity base stations per transect. Precise latitude, longitude and ground surface elevation at each location were measured using an OPUS corrected Trimble RTK-GPS unit. Base stations were chosen based on ease of access due to the necessity of repeat measurements. Gravity measurement locations were selected and marked to provide easy access and repeat measurements. The gravimeter was returned to a base station within every two hours and a looping procedure was used to determine drift and maximize confidence in the gravity measurements. A two-minute calibration reading at each station was used to minimize any tares in the data. The Gravitron digitally recorded finite impulse response filtered gravity measurements every 20 seconds at each station. A measurement period of 15 minutes was used for each base station occupation and a minimum of 5 minutes at all other locations. Longer or multiple measurements were utilized at some sites if drift or other externalities (i.e. train or truck traffic) were effecting readings. Average, median, standard deviation and 95% confidence interval were calculated for each station. Tidal, drift, latitude, free-air, Bouguer and terrain corrections were then applied. The results show that the gravitational field decreases as alluvium thickness increases across the axes of the Susquehanna River and Muncy Creek valleys. However, the location of the gravity low does not correspond with the present-day location of the West Branch of the Susquehanna River (WBSR), suggesting that the WBSR may have been constrained along Bald Eagle Mountain by a glacial lobe originating from the Muncy Creek Valley to the northeast. Using a 3-D inversion model, the topography of the bedrock-alluvium interface was determined over the extent of the study area using a density contrast of -0.8 g/cm3. Our results are consistent with the bedrock geometry of the area, and provide a low-cost, non-invasive and efficient method for exploring the subsurface and for supplementing existing well data.

Sleepless night, the moon is bright: longitudinal study of lunar phase and sleep

Popular belief holds that the lunar cycle affects human physiology, behaviour and health. We examined the influence of moon phase on sleep duration in a secondary analysis of a feasibility study of mobile telephone base stations and sleep quality. We studied 31 volunteers (18 women and 13 men, mean age 50 years) from a suburban area of Switzerland longitudinally over 6 weeks, including two full moons. Subjective sleep duration was calculated from sleep diary data. Data were analysed using multiple linear regression models with random effects. Mean sleep duration was 6 h 49 min. Subjective sleep duration varied with the lunar cycle, from 6 h 41 min at full moon to 7 h 00 min at new moon (P < 0.001). Average sleep duration was shortened by 68 min during the week compared with weekends (P < 0.001). Men slept 17 min longer than women (P < 0.001) and sleep duration decreased with age (P < 0.001). There was also evidence that rating of fatigue in the morning was associated with moon phase, with more tiredness (P = 0.027) at full moon. The study was designed for other purposes and the association between lunar cycle and sleep duration will need to be confirmed in further studies.

Exposure modeling of high-frequency electromagnetic fields

We developed a geospatial model that calculates ambient high-frequency electromagnetic field (HF-EMF) strengths of stationary transmission installations such as mobile phone base stations and broadcast transmitters with high spatial resolution in the order of 1 m. The model considers the location and transmission patterns of the transmitters, the three-dimensional topography, and shielding effects by buildings. The aim of the present study was to assess the suitability of the model for exposure monitoring and for epidemiological research. We modeled time-averaged HF-EMF strengths for an urban area in the city of Basel as well as for a rural area (Bubendorf). To compare modeling with measurements, we selected 20 outdoor measurement sites in Basel and 18 sites in Bubendorf. We calculated Pearson's correlation coefficients between modeling and measurements. Chance-corrected agreement was evaluated by weighted Cohen's kappa statistics for three exposure categories. Correlation between measurements and modeling of the total HF-EMF strength was 0.67 (95% confidence interval (CI): 0.33-0.86) in the city of Basel and 0.77 (95% CI: 0.46-0.91) in the rural area. In both regions, kappa coefficients between measurements and modeling were 0.63 and 0.77 for the total HF-EMF strengths and for all mobile phone frequency bands. First evaluation of our geospatial model yielded substantial agreement between modeling and measurements. However, before the model can be applied for future epidemiologic research, additional validation studies focusing on indoor values are needed to improve model validity.Journal of Exposure Science and Environmental Epidemiology (2008) 18, 183-191; doi:10.1038/sj.jes.7500575; published online 4 April 2007.

Temporal and spatial variability of personal exposure to radio frequency electromagnetic fields

BACKGROUND: Little is known about the population's exposure to radio frequency electromagnetic fields (RF-EMF) in industrialized countries. OBJECTIVES: To examine levels of exposure and the importance of different RF-EMF sources and settings in a sample of volunteers living in a Swiss city. METHODS: RF-EMF exposure of 166 volunteers from Basel, Switzerland, was measured with personal exposure meters (exposimeters). Participants carried an exposimeter for 1 week (two separate weeks in 32 participants) and completed an activity diary. Mean values were calculated using the robust regression on order statistics (ROS) method. RESULTS: Mean weekly exposure to all RF-EMF sources was 0.13 mW/m(2) (0.22 V/m) (range of individual means 0.014-0.881 mW/m(2)). Exposure was mainly due to mobile phone base stations (32.0%), mobile phone handsets (29.1%) and digital enhanced cordless telecommunications (DECT) phones (22.7%). Persons owning a DECT phone (total mean 0.15 mW/m(2)) or mobile phone (0.14 mW/m(2)) were exposed more than those not owning a DECT or mobile phone (0.10 mW/m(2)). Mean values were highest in trains (1.16 mW/m(2)), airports (0.74 mW/m(2)) and tramways or buses (0.36 mW/m(2)), and higher during daytime (0.16 mW/m(2)) than nighttime (0.08 mW/m(2)). The Spearman correlation coefficient between mean exposure in the first and second week was 0.61. CONCLUSIONS: Exposure to RF-EMF varied considerably between persons and locations but was fairly consistent within persons. Mobile phone handsets, mobile phone base stations and cordless phones were important sources of exposure in urban Switzerland.

A prediction model for personal radio frequency electromagnetic field exposure

Radio frequency electromagnetic fields (RF-EMF) in our daily life are caused by numerous sources such as fixed site transmitters (e.g. mobile phone base stations) or indoor devices (e.g. cordless phones). The objective of this study was to develop a prediction model which can be used to predict mean RF-EMF exposure from different sources for a large study population in epidemiological research. We collected personal RF-EMF exposure measurements of 166 volunteers from Basel, Switzerland, by means of portable exposure meters, which were carried during one week. For a validation study we repeated exposure measurements of 31 study participants 21 weeks after the measurements of the first week on average. These second measurements were not used for the model development. We used two data sources as exposure predictors: 1) a questionnaire on potentially exposure relevant characteristics and behaviors and 2) modeled RF-EMF from fixed site transmitters (mobile phone base stations, broadcast transmitters) at the participants' place of residence using a geospatial propagation model. Relevant exposure predictors, which were identified by means of multiple regression analysis, were the modeled RF-EMF at the participants' home from the propagation model, housing characteristics, ownership of communication devices (wireless LAN, mobile and cordless phones) and behavioral aspects such as amount of time spent in public transports. The proportion of variance explained (R2) by the final model was 0.52. The analysis of the agreement between calculated and measured RF-EMF showed a sensitivity of 0.56 and a specificity of 0.95 (cut-off: 90th percentile). In the validation study, the sensitivity and specificity of the model were 0.67 and 0.96, respectively. We could demonstrate that it is feasible to model personal RF-EMF exposure. Most importantly, our validation study suggests that the model can be used to assess average exposure over several months.

Magnetic anomaly map of the Weddell Sea Region, Antarctic (Scale 1:2 500 000)

This paper describes a 1 : 2 500 000 scale aeromagnetic anomaly map produced by the joint efforts of VNIIOkeangeologia, Polar Marine Geological Research Expedition (PMGRE) and the Alfred Wegener Institute for Polar and Marine Research (AWl) for the Weddell Sea region covering 1 850 000 km' of West Antarctica. Extensive regional magnetic survey flights with line-spacing of about 20 km and 5 km were carried out by the PMGRE between 1977 and 1989. In course of these investigations the PMGRE flew 9 surveys with flight-line spacing of 20 km and 6 surveys with flight-line spacing of 5 km mainly over the mountain areas of southern Palmer Land, western Dronning Maud Land, Coats Land and Pensacola Mountains, over the Ronne lee Shelf and the Filchner Ice Shelf and the central part of the Weddell Sea. More than 215 000 line-kilometers of total field aeromagnetic data have been acquired by using an Ilyushin Il-14 ski-equipped aircraft. Survey operations were centered on the field base stations Druzhnaya-1, -2, and -3, from which the majority of the Weddell Sea region network was completed. The composite map of the Weddell Sea region is prepared in colour, showing magnetic anomaly contours at intervals of 50-100 nT with supplemental contours at an interval of 25 nT in low gradient areas, on a polar stereographic projection. The compiled colour magnetic anomaly map of the Weddell Sea region demonstrates that features of large areal extent, such as geologic provinces, fold-belts, ancient eratonic fragments and other regional structural features can be readily delineated. The map allows a comparison of regional magnetic features with similar-scale geological structures on geological and geophysical maps. It also provides a database for the future production of the ''Digital Magnetic Anomaly Map of Antarctica'' in the framework of the Scientific Committee on Antarctic Research/International Association of Geomagnetism and Aeronomy (SCAR/IAGA) compilation.

Correction of systematic errors in Wide Area Multilateration

This work presents a method to estimate and correct slow time-dependent position errors due to non perfect ground station synchronization and tropospheric propagation. It uses opportunity traffic emissions, i.e. signals transmitted from the aircrafts within the coverage zone. This method is used to overcome the difficulty of installing reference beacons simultaneously visible by all the base stations in a given Wide Area Multilateration (WAM) system.

Multibeam Network Design and Measurement for Triangular Array of Three Radiating Elements

Nowadays, more a more base stations are equipped with active conformal antennas. These antenna designs combine phase shift systems with multibeam networks providing multi-beam ability and interference rejection, which optimize multiple channel systems. GEODA is a conformal adaptive antenna system designed for satellite communications. Operating at 1.7 GHz with circular polarization, it is possible to track and communicate with several satellites at once thanks to its adaptive beam. The antenna is based on a set of similar triangular arrays that are divided in subarrays of three elements called `cells'. Transmission/Receiver (T/R) modules manage beam steering by shifting the phases. A more accurate steering of the antenna GEODA could be achieved by using a multibeam network. Several multibeam network designs based on Butler network will be presented

Series combination of a switched dc-dc converter and a linear regulator for high frequency RF envelope amplifier

Classical linear amplifiers such as A, AB and B offer very good linearity suitable for RF power amplifiers. However, its inherent low efficiency limits its use especially in base-stations that manage tens or hundreds of Watts. The use of linearization techniques such as Envelope Elimination and Restoration (EER) allow an increase of efficiency keeping good linearity. This technique requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier. In this paper, several alternatives are analyzed to implement the envelope amplifier based on a cascade association of a switched dc-dc converter and a linear regulator. A simplified version of this approach is also suitable to operate with Envelope Tracking technique.

Non invasive moisture measurement in agricultural fiel using a rolling spherical robot

Irrigation management in large crop fields is a very important practice. Since the farm management costs and the crop results are directly connected with the environmental moisture, water control optimization is a critical factor for agricultural practices, as well as for the planet sustainability. Usually, the crop humidity is measured through the water stress index (WSI), using imagery acquired from satellites or airplanes. Nevertheless, these tools have a significant cost, lack from availability, and dependability from the weather. Other alternative is to recover to ground tools, such as ground vehicles and even static base stations. However, they have an outstanding impact in the farming process, since they can damage the cultivation and require more human effort. As a possible solution to these issues, a rolling ground robot have been designed and developed, enabling non-invasive measurements within crop fields. This paper addresses the spherical robot system applied to intra-crop moisture measurements. Furthermore, some experiments were carried out in an early stage corn field in order to build a geo-referenced WSI map.

Técnicas avanzadas de diseño y análisis de rendimiento en despliegues inalámbricos en interiores

En los últimos tiempos, el tráfico generado por los usuarios de redes móviles ha crecido de manera muy notable, y se prevé que dicho crecimiento se mantenga de manera continuada a lo largo de los próximos años. El tráfico gestionado por redes móviles se ha multiplicado por cinco entre los años 2010 y 2013, y las predicciones señalan un aumento de diez veces entre 2013 y 2019. De este tráfico que deben gestionar las redes móviles, una gran parte se genera en el interior de edificios. En la actualidad, éste oscila entre el 70% y el 80% del tráfico móvil total, y este porcentaje se prevé que aumente hasta cerca del 95% en los próximos años. En esta situación, con el tráfico móvil aumentando de manera exponencial, especialmente en interiores, el despliegue de soluciones específicas para estos entornos se antoja imprescindible para evitar situaciones de saturación constante de las redes móviles. Desde el punto de vista de los operadores móviles, estas soluciones permitirán limitar los problemas de cobertura, mejorar la eficiencia del uso de recursos radio y reducir el coste de las infraestructuras. Asimismo, desde el punto de vista de los usuarios, estos despliegues específicos en interiores permitirán suministrar de manera continua altas tasas de transferencia y satisfacer los altos requisitos de calidad de servicio que demandan los servicios en tiempo real. La complejidad de las actuaciones a realizar para llevar a cabo el despliegue de soluciones específicas en interiores varía considerablemente según el tipo de entorno al que están destinadas. Por un lado, las soluciones en escenarios de tipo residencial se caracterizan por despliegues masivos de transmisores realizados por los propios usuarios. De esta manera, no hay posibilidad de realizar ningún tipo de planificación previa que permita la optimización del rendimiento y solo se puede recurrir, para la mejora de éste, a métodos de autoconfiguración y autooptimización. Por otro lado, las soluciones en entornos empresariales se caracterizan por la necesidad de realizar una labor de diseño y planificación previa, cuya dificultad estará asociada a las dimensiones del escenario de despliegue y al número de transmisores necesarias. De esta labor de diseño y de la configuración de los elementos involucrados en la solución desplegada dependerá el funcionamiento adecuado de la red, el rendimiento conseguido y la calidad del servicio que se podrá suministrar a través de ésta. En esta Tesis Doctoral se abordan dos de los problemas principales en el ámbito del despliegue de soluciones específicas de interiores. El primero de ellos es la dificultad para estimar la capacidad y el rendimiento que puede garantizarse mediante soluciones autodesplegadas, y el segundo es la complejidad de diseñar y configurar despliegues de soluciones específicas de interiores en entornos empresariales que requieran un número de transmisores considerable. En el ámbito de los autodespliegues en escenarios residenciales, las principales contribuciones originales de esta Tesis Doctoral se centran en el diseño, desarrollo e implementación de procedimientos que permitan de manera sencilla y precisa la estimación de la capacidad y el rendimiento en autodespliegues. Por otro lado, en el ámbito de los despliegues en escenarios empresariales, las aportaciones originales de esta Tesis consisten en el desarrollo de nuevas técnicas que permitan el diseño automático de soluciones específicas de interiores en estos entornos. Los resultados obtenidos han permitido la creación de herramientas específicas para el análisis del rendimiento de autodespliegues en escenarios residenciales reales y para el diseño y configuración de despliegues en escenarios empresariales. Estas herramientas permiten sistematizar la aplicación práctica de las contribuciones de la presente Tesis Doctoral. ABSTRACT In recent times, the traffic generated by users of mobile networks has grown very significantly, and this increase is expected to continue steadily over the next few years. Traffic carried by mobile networks has increased fivefold between 2010 and 2013, and forecasts indicate a tenfold increase between 2013 and 2019. Furthermore, a great part of this traffic is generated inside buildings. Currently, between 70% and 80% of mobile traffic occurs inside buildings, and this percentage is expected to increase to about 95% in the coming years. In this situation, with mobile traffic growing exponentially, especially indoors, the deployment of specific solutions for these environments can be essential to avoid a constant saturation of mobile networks. On the one hand, from the point of view of mobile operators, these solutions will help to reduce the problems of coverage, improve the efficiency of radio resource usage and reduce the cost of infrastructures. Also, from the point of view of users, these specific indoor deployments can both guarantee high data transfer rates and meet the high quality of service requirements associated with real-time services. The complexity of the actions required to carry out the deployment of specific solutions indoors varies considerably depending on the type of scenario they are conceived to. On the one hand, residential scenarios are characterized by massive deployments of base stations made by the user, so there is no possibility of any prior planning. In this case only self-configuration, selfoptimization and self-healing methods can be considered for performance optimization. On the other hand, specific in-building solutions in enterprise environments requires a previous design and planning phase, whose difficulty is closely associated with the size of the deployment scenario and the number of base stations required. The design and configuration of the elements included in the solution will determine its performance and the quality of service that can be guaranteed. The objective of the present Thesis is to address two of the main issues related to specific indoor solutions, such as the difficulty of assessing the capacity and the performance which can be guaranteed by means of self-deployments and the complexity of the design and configuration of deployments in enterprise environments requiring a large number of base stations. The main contribution of this thesis consists of the development of techniques and simple tools for design and performance analysis of indoor wireless networks deployments. The main results include the development of procedures for assessing the capacity and performance of self-deployments in residential scenarios, the performance analysis of real residential self-deployments using the proposed procedures and the development of techniques for the automatic design of wireless networks in enterprise environments. The results obtained have allowed the creation of specific software tools for both the performance analysis of self-deployments and the design and deployment of in-building solutions in enterprise scenarios. These software tools are conceived to systematize the practical application of the contributions of this Thesis.