内陆湖沼相和近海沼泽相沉积环境煤中微量元素和矿物的对比研究—以辽宁北票、江西建新和桥头煤研究为例

Using knowledge of geology, geochemistry, coal petrology, mineralogy, by means of a variety of advanced measuring methods such as inductively coupled plasma mass spectrometry (ICP-MS), inductively coupled atomic emission spectrometry (ICP-AES), X-ray powder diffraction (XRD), scanning electron microscopy with energy-dispersive spectrometer(SEM-EDS), sequential chemical extract and density fractions, the characteristics of trace elements and minerals in Jurassic Beipiao coal mine under inland limnetic sedimentary environment and in late Permian Jianxin and Qiaotou coal mines under paralic swamp sedimentary environment were studied. Compared with the average concentration in the world bituminous coals, the Beipiao coal was characterized by relatively high contents of Sc, Ti, Cr, Co, Ni, Zn, Se, Sr, Zr, Y, Ba, REE and Th, and lower contents of V, Rb, Cd, Sn, Pb, Bi and U; while the Jianxin coal was relatively enriched in Li, Sc, Ga, Sr, Y, Nb, Sb, Th and U, with low concentration of Be, Co, Ni, Cu, Ge, Zr, Mo, Cd, Cs, Ba, Pb and Bi; and the Qiaotou coal was enriched in Li, Sc, Sr, Nb, Ta, Zr, REE, Hf, Th and U, with low concentration of Be, V, Co, Ni, Cu, Ge, Mo, Cd, Cs, Ba, Tl, Pb and Bi. The concentrations of Ca, Mg and K in Beipiao coal are higher than those in Jianxin coal and Qiaotou coal, while Fe, S and Ti in Beipiao coal are lower than those in Jianxin coal and Qiaotou coal. The proximate analysis of coal samples was carried out, which indicated that Beipiao coal was medium- to high- ash (5.92-60.68%) with low sulphur coal, and Jianxin coal and Qiaotou coal was medium to high ash (8.85-46.33%) with high sulphur. The reflectivity was measured, which explained that Beipiao coal belonged to high volatile bituminous coal, Jianxin coal was low volatile bituminous coal and Qiaotou coal was low volatile anthracite. Quantitative maceral analyses were studied. The characteristics of rare earth elements (REE) were investigated, which showed that the total contents of REE were higher than that of the world's average content. With the increase of coal's metamorphic grade, the total contents of REE decreased from 98.5 X 10"6 of Beipiao coal to 94.2 X 10"6 of Jianxin coal, and to 75.9 X 10"6 of Qiaotou coal, and 5Eu reduced which indicated that the element Eu depleted. The characteristics of REE was controlled by the metamorphic grade of coal. And REE were mainly absorbed in clay minerals in Beipiao coal samples, while in Jianxin and Qiaotou coal mines, REE were primarily related to clay mineral and pyrite. The variation of trace elements in vertical direction of coal seams was studied, and the results showed that different trace elements differed greatly. The correlation between trace elements and ash were determined. Four major trace elements (aluminium-silicates, sulphide, carbonate and phosphate) accounted for the occurrence and distribution of most elements studied were determined. Coal samples were separated by density fraction, which showed that Cr, Cu, Mo and Pb were closely related to inorganic matters mainly distributed in P >2.6 and dropped remarkably in the density fractions P <2.3 . The occurrences of Co, Cr, Ni, As, Se, Mo, U were studied directly and quantitatively using sequential chemical extract with six steps, which showed that Co. Ni, Mo and U were mainly in the form of mineral, and As, Se chiefly in the form of organic state, while Cr mostly in the form of organic state and mineral. Major mineral phases presented in the Beipiao coal were Kaolinite, illite, quartz, calcite, and small amount of siderite, barite. While major mineral phases in Jianxin and Qiaotou coal were pyrite, kaolinite, and small amount of marcasite, rutile, sphalerite. This is the first time that the chromite in the coal was discovered in China, which indicates that Cr occurrence appeared in the form of chromite. The ratio of Sr/Ba, Sr/Ca and V/Ni in Beipiao coal mine under inland limnetic is smaller than that of in Jianxin and Qiaotou coal mines under paralic swamp. The ratio of K/Na and Th/U of Beipiao coal mine is higher than that of Jianxin and Qiaotou coal mine, which proved that Beipiao coal was not affected by sea water and Jianxin and Qiaotou coal were affected by sea water. Trace elements such as Cr, Ni, Mo in minerals were analyzed by SEM-EDS. The factors controlling the enrichment of trace elements can be divided into syngenetic stage factors and epigenetic stage factors.

Corrosion behavior in graphite refractories impregnated with ZrO 2 and CeO 2 carrying solutions

This paper investigates corrosion behavior in graphite refractory hot metal impregnated with ZrO 2 and CeO 2 carrying solutions used in Blast Furnace hearth, consisting of 50% graphite and 50% anthracite. Corrosions tests were carried out by means of finger test method in an induction furnace, using bar-shaped 30×30×280 mm test specimens and hot metal from CSN#2 Blast Furnace runner. The temperature chosen for this test was 1520°C and sixty-minute isotherm. Upon test completion, test specimens were characterized by their dimensional variation, X-ray diffractometry and Scanning Electronic Microscopy (SEM).

Argilas modificadas: remoção de antraceno e ácido 9-antróico como modelo para aromáticos (hpa) presentes em águas

Pós-graduação em Química - IBILCE

Operational and environmental assessment on the use of charcoal in iron ore sinter production

A study was carried out into the use of charcoal as a supplementary fuel in the iron-ore sintering process. The primary fuel was coke breeze and anthracite with 0, 10, 25, 50 and 100% replacement of the energy input with charcoal to produce sinter. This was achieved by considering the carbon content of each fuel and its corresponding participation on fuel blending, in order to have the same carbon input in each test run. An extensive analysis of the environmental impact was carried out regarding the atmospheric pollutants characterization (dust, sulphur dioxide, nitrogen oxides, carbon monoxide, carbon dioxide, methane, total hydrocarbons, and dioxins and furans). Experimental results indicate that fuel blending where 50% of the heat input was provided by charcoal may be comparable with those using 100% coke, under normal sintering conditions, and may result in a 50% reduction on greenhouse gas emission. It was also observed that while dust, methane and hydrocarbons emissions increased, the total dioxins and furans, expressed as polychlorinated dibenzodioxins/furans, decreased approximately 50% when compared with operation with 100% coke.

Abandoned Coal Mine Drainage and Its Remediation: Impacts on Stream Ecosystem Structure and Function

The effects of abandoned mine drainage (AMD) on streams and responses to remediation efforts were studied using three streams (AMD-impacted, remediated, reference) in both the anthracite and the bituminous coal mining regions of Pennsylvania (USA). Response variables included ecosystem function as well as water chemistry and macroinvertebrate community composition. The bituminous AMD stream was extremely acidic with high dissolved metals concentrations, a prolific mid-summer growth of the filamentous alga, Mougeotia, and .10-fold more chlorophyll than the reference stream. The anthracite AMD stream had a higher pH, substrata coated with iron hydroxide(s), and negligible chlorophyll. Macroinvertebrate communities in the AMD streams were different from the reference streams, the remediated streams, and each other. Relative to the reference stream, the AMD stream(s) had (1) greater gross primary productivity (GPP) in the bituminous region and undetectable GPP in the anthracite region, (2) greater ecosystem respiration in both regions, (3) greatly reduced ammonium uptake and nitrification in both regions, (4) lower nitrate uptake in the bituminous (but not the anthracite) region, (5) more rapid phosphorus removal from the water column in both regions, (6) activities of phosphorus-acquiring, nitrogenacquiring, and hydrolytic-carbon-acquiring enzymes that indicated extreme phosphorus limitation in both regions, and (7) slower oak and maple leaf decomposition in the bituminous region and slower oak decomposition in the anthracite region. Remediation brought chlorophyll concentrations and GPP nearer to values for respective reference streams, depressed ecosystem respiration, restored ammonium uptake, and partially restored nitrification in the bituminous (but not the anthracite) region, reduced nitrate uptake to an undetectable level, restored phosphorus uptake to near normal rates, and brought enzyme activities more in line with the reference stream in the bituminous (but not the anthracite) region. Denitrification was not detected in any stream. Water chemistry and macroinvertebrate community structure analyses capture the impact of AMD at the local reach scale, but functional measures revealed that AMD has ramifications that can cascade to downstream reaches and perhaps to receiving estuaries.

Influencia de las restricciones medioambientales en el sector eléctrico

El objetivo de esta tesis es la caracterización de la generación térmica representativa de la existente en la realidad, para posteriormente proceder a su modelización y simulación integrándolas en una red eléctrica tipo y llevar a cabo estudios de optimización multiobjetivo económico medioambiental. Para ello, en primera instancia se analiza el contexto energético y eléctrico actual, y más concretamente el peninsular, en el que habiendo desaparecido las centrales de fuelóleo, sólo quedan ciclos combinados y centrales de carbón de distinto rango. Seguidamente se lleva a cabo un análisis de los principales impactos medioambientales de las centrales eléctricas basadas en combustión, representados sobre todo por sus emisiones de CO2, SO2 y NOx, de las medidas de control y mitigación de las mismas y de la normativa que les aplica. A continuación, a partir de las características de los combustibles y de la información de los consumos específicos, se caracterizan los grupos térmicos frente a las funciones relevantes que definen su comportamiento energético, económico y medioambiental, en términos de funciones de salida horarias dependiendo de la carga. Se tiene en cuenta la posibilidad de desnitrificación y desulfuración. Dado que las funciones objetivo son múltiples, y que están en conflicto unas con otras, se ha optado por usar métodos multiobjetivo que son capaces de identificar el contorno de puntos óptimos o frente de Pareto, en los que tomando una solución no existe otra que lo mejore en alguna de las funciones objetivo sin empeorarlo en otra. Se analizaron varios métodos de optimización multiobjetivo y se seleccionó el de las ε constraint, capaz de encontrar frentes no convexos y cuya optimalidad estricta se puede comprobar. Se integró una representación equilibrada de centrales de antracita, hulla nacional e importada, lignito y ciclos combinados en la red tipo IEEE-57, en la que se puede trabajar con siete centrales sin distorsionar demasiado las potencias nominales reales de los grupos, y se programó en Matlab la resolución de flujos óptimos de carga en alterna con el método multiobjetivo integrado. Se identifican los frentes de Pareto de las combinaciones de coste y cada uno de los tres tipos de emisión, y también el de los cuatro objetivos juntos, obteniendo los resultados de costes óptimos del sistema para todo el rango de emisiones. Se valora cuánto le cuesta al sistema reducir una tonelada adicional de cualquier tipo de emisión a base de desplazarse a combinaciones de generación más limpias. Los puntos encontrados aseguran que bajo unas determinadas emisiones no pueden ser mejorados económicamente, o que atendiendo a ese coste no se puede reducir más allá el sistema en lo relativo a emisiones. También se indica cómo usar los frentes de Pareto para trazar estrategias óptimas de producción ante cambios horarios de carga. ABSTRACT The aim of this thesis is the characterization of electrical generation based on combustion processes representative of the actual power plants, for the latter modelling and simulation of an electrical grid and the development of economic- environmental multiobjective optimization studies. In this line, the first step taken is the analysis of the current energetic and electrical framework, focused on the peninsular one, where the fuel power plants have been shut down, and the only ones remaining are coal units of different types and combined cycle. Then it is carried out an analysis of the main environmental impacts of the thermal power plants, represented basically by the emissions of CO2, SO2 y NOx, their control and reduction measures and the applicable regulations. Next, based on the combustibles properties and the information about the units heat rates, the different power plants are characterized in relation to the outstanding functions that define their energy, economic and environmental behaviour, in terms of hourly output functions depending on their load. Optional denitrification and desulfurization is considered. Given that there are multiple objectives, and that they go in conflictive directions, it has been decided the use of multiobjective techniques, that have the ability of identifying the optimal points set, which is called the Pareto front, where taken a solution there will be no other point that can beat the former in an objective without worsening it in another objective. Several multiobjective optimization methods were analysed and pondered, selecting the ε constraint technique, which is able to find no convex fronts and it is opened to be tested to prove the strict Pareto optimality of the obtained solutions. A balanced representation of the thermal power plants, formed by anthracite, lignite, bituminous national and imported coals and combined cycle, was integrated in the IEEE-57 network case. This system was selected because it deals with a total power that will admit seven units without distorting significantly the actual size of the power plants. Next, an AC optimal power flow with the multiobjective method implemented in the routines was programmed. The Pareto fronts of the combination of operative costs with each of the three emissions functions were found, and also the front of all of them together. The optimal production costs of the system for all the emissions range were obtained. It is also evaluated the cost of reducing an additional emission ton of any of the emissions when the optimal production mix is displaced towards cleaner points. The obtained solutions assure that under a determined level of emissions they cannot be improved economically or, in the other way, at a determined cost it cannot be found points of lesser emissions. The Pareto fronts are also applied for the search of optimal strategic paths to follow the hourly load changes.

Aprovechamiento térmico de residuos estériles de carbón para generación eléctrica mediante tecnologías de combustión y gasificación eficientes y con mínimo impacto ambiental

La presente tesis doctoral, “Aprovechamiento térmico de residuos estériles de carbón para generación eléctrica mediante tecnologías de combustión y gasificación eficientes y con mínimo impacto ambiental”, desarrolla la valorización energética de los residuos del carbón, estériles de carbón, producidos durante las etapas de extracción y lavado del carbón. El sistema energético se encuentra en una encrucijada, estamos asistiendo a un cambio en el paradigma energético y, en concreto, en el sector de la generación eléctrica. Se precipita un cambio en la generación y el consumo eléctricos. Una mayor concienciación por la salud está forzando la contención y eliminación de agentes contaminantes que se generan por la utilización de combustibles fósiles de la forma en la que se viene haciendo. Aumenta la preocupación por el cambio climático y por contener en 2°C el aumento de la temperatura de la Tierra para final de este siglo, circunstancia que está impulsando el desarrollo e implantación definitiva de tecnología de control y reducción de emisiones CO2. Generar electricidad de una manera sostenible se está convirtiendo en una obligación. Esto se materializa en generar electricidad respetando el medioambiente, de una forma eficiente en la utilización de los recursos naturales y a un coste competitivo, pensando en el desarrollo de la sociedad y en el beneficio de las personas. En la actualidad, el carbón es la principal fuente de energía utilizada para generar electricidad, y su empleo presenta la forma de energía más barata para mejorar el nivel de vida de cualquier grupo y sociedad. Además, se espera que el carbón siga presente en el mix de generación eléctrica, manteniendo una significativa presencia y extrayéndose en elevadas cantidades. Pero la producción de carbón lleva asociada la generación de un residuo, estéril, que se produce durante la extracción y el lavado del mineral de carbón. Durante décadas se ha estudiado la posibilidad de utilizar el estéril y actualmente se utiliza, en un limitado porcentaje, en la construcción de carreteras, terraplenes y rellenos, y en la producción de algunos materiales de construcción. Esta tesis doctoral aborda la valorización energética del estéril, y analiza el potencial aprovechamiento del residuo para generar electricidad, en una instalación que integre tecnología disponible para minimizar el impacto medioambiental. Además, persigue aprovechar el significativo contenido en azufre que presenta el estéril para producir ácido sulfúrico (H2SO4) como subproducto de la instalación, un compuesto químico muy demandado por la industria de los fertilizantes y con multitud de aplicaciones en otros mercados. Se ha realizado el análisis de caracterización del estéril, los parámetros significativos y los valores de referencia para su empleo como combustible, encontrándose que su empleo como combustible para generar electricidad es posible. Aunque en España se lleva extrayendo carbón desde principios del siglo XVIII, se ha evaluado para un período más reciente la disponibilidad del recurso en España y la normativa existente que condiciona su aplicación en el territorio nacional. Para el período evaluado, se ha calculado que podrían estar disponibles más de 68 millones de toneladas de estéril susceptibles de ser valorizados energéticamente. Una vez realizado el análisis de la tecnología disponible y que podría considerarse para emplear el estéril como combustible, se proponen cuatro configuraciones posibles de planta, tres de ellas basadas en un proceso de combustión y una de ellas en un proceso de gasificación. Tras evaluar las cuatro configuraciones por su interés tecnológico, innovador y económico, se desarrolla el análisis conceptual de una de ellas, basada en un proceso de combustión. La instalación propuesta tiene una capacidad de 65 MW y emplea como combustible una mezcla de carbón y estéril en relación 20/80 en peso. La instalación integra tecnología para eliminar en un 99,8% el SO2 presente en el gas de combustión y en más de un 99% las partículas generadas. La instalación incorpora una unidad de producción de H2SO4, capaz de producir 18,5 t/h de producto, y otra unidad de captura para retirar un 60% del CO2 presente en la corriente de gases de combustión, produciendo 48 tCO2/h. La potencia neta de la planta es 49,7 MW. Se ha calculado el coste de inversión de la instalación, y su cálculo resulta en un coste de inversión unitario de 3.685 €/kW. ABSTRACT The present doctoral thesis, “Thermal utilisation of waste coal for electricity generation by deployment of efficient combustion and gasification technologies with minimum environmental impact”, develops an innovative waste-to-energy concept of waste coals produced during coal mining and washing. The energy system is at a dilemma, we are witnessing a shift in the energy paradigm and specifically in the field of electricity generation. A change in the generation and electrical consumption is foreseen. An increased health consciousness is forcing the containment and elimination of pollutants that are generated by the use of fossil fuels in the way that is being done. Increasing concern about climate change and to contain the rise of global temperature by 2°C by the end of this century, is promoting the development and final implementation of technology to control and reduce the CO2 emission. Electricity generation in a sustainable manner is becoming an obligation. This concept materialised in generating electricity while protecting the environment and deployment of natural resources at a competitive cost, considering the development of society and people´s benefit. Currently, coal is the main source of energy employ to generate electricity, and its use represents the most cost competitive form of energy to increase the standard of living of any group or society. Moreover, coal will keep playing a key role in the global electricity generation mix, maintaining a significant presence and being extracting in large amounts. However, coal production implies the production of waste, termed waste coal or culm in Pennsylvania anthracite extraction, produced during coal mining and coal washing activities. During the last decades, the potential use of waste coal has been studied, and currently, in a limited amount, waste coal is used in roads construction, embankments and fillings, and to produce some construction materials. This doctoral thesis evaluates the waste to energy of waste coals and assesses its potential use to generate electricity, implementing available technology to minimise the environment impact. Additionally, it pursues the significant advantage that presents sulphur content in waste coal to produce sulphuric acid (H2SO4) as a byproduct of the waste-to-energy process, a chemical compound highly demanded by the fertiliser industry and many applications in other markets. It analyses the characteristics of waste coal, and assesses the significant parameters and reference values for its use as fuel, being its fuel use for electricity generation very possible. While mining coal is taking place in Spain since the 1700s, it has been evaluated for a more recent period the waste coal available in Spain and the existing legislation that affects its application and deploy to generate electricity in the country. For the evaluation period has been calculated that may be available more than 68 million tons of waste coal that can be waste-toenergy. The potential available technology to deploy waste coal as fuel has been evaluated and assessed. After considering this, the doctoral thesis proposes four innovative alternatives of facility configuration, three of them based on a combustion process and one in a gasification process. After evaluating the four configurations for its technological, innovative and economic interest, the conceptual analysis of one of alternatives, based on a combustion process, takes place. The proposed alternative facility developed has a capacity of 65 MW, using as fuel a mixture of coal and waste coal 80/20 by weight. The facility comprises technology to remove 99.8% SO2 present in the flue gas and more than 99% of the particles. The facility includes a unit capable of producing 18.5 t/h of H2SO4, and another capture facility, removing 60% of CO2 present in the flue gas stream, producing 48 tCO2/h. The net capacity of the power station is 49.7 MW. The facility unitary cost of investment is 3,685 €/kW.

Influência do método de lavagem nas características de carvões antracitoso e betuminoso utilizados em meio filtrante

Teve como objetivo verificar e comparar a alteração das características do carvão antracitoso e do carvão betuminoso utilizados em meio filtrante, devido ao efeito abrasivo causado entre os grãos decorrentes de lavagens exclusivamente com água e lavagens independentes com ar e água. Foram estudados dois tipos de carvão antracitoso e um tipo de carvão betuminoso, para os quais foram determinadas suas características químicas e físicas. Os ensaios foram realizados em uma instalação ao piloto montada na escola de engenharia de São Carlos-EESC, USP, na qual foram feitas simulações de lavagens admitindo-se uma lavagem diária durante um ano para cada método, de modo intermitente, em que o meio granular era compactado ao final de cada lavagem, e continuo, sem compactação do meio granular. A velocidade ascensional utilizada para cada simulação de lavagem foi de 0,9 m/min, promovendo expansão no meio granular de 35 a 40%. A taxa de ar utilizada para as simulações de lavagens com aplicação de ar foi de 15 l/sm2. Após o término das 365 lavagens, foram determinados os valores médios do coeficiente de esfericidade e da porosidade do meio granular estratificado e construída a curva de distribuição granulométrica das amostras utilizadas nos ensaios. Conclui-se que o carvão betuminoso apresentou comportamento semelhante ao dos carvões antracitosos e que a metodologia de lavagem continua produz praticamente o mesmo efeito abrasivo comparada a de lavagem intermitente.