Elaboration et caractérisation de ciments géopolymères à base de scories volcaniques

Two types of volcanic ashes referenced as ZD (volcanic ashes from Djoungo) and ZG (volcanic ashes from Galim) were collected from two Cameroonian localities. They were characterized (chemical and mineralogical compositions, amorphous phase content, particle size distribution and specific surface area) and used as raw materials for the synthesis of geopolymer cements at ambient temperature of laboratory (24 ± 3 °C). The synthesized products were characterized by determining their setting time, linear shrinkage and compressive strength, X-ray Diffraction, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy. The mineralogical composition, the amorphous phase content, the particle size distribution, the specific surface area of the volcanic ashes as well as the mass ratio of the alkaline solution (sodium silicate / sodium hydroxide) were the main parameters which influenced the synthesis of geopolymers with interesting characteristics at ambient temperature (24 ± 3 °C). The volcanic ashes (ZD) whose mineralogical composition contained anhydrite, low amorphous phase content and low specific surface area led to long setting times. Moreover, its products swelled and presented cracks due to the formation of ettringite and these resulted in low compressive strengths (7 to 19 MPa). The volcanic ashes (ZG) containing high amounts of amorphous phase and high specific surface area led geopolymers with setting times between 490 and 180 minutes and compressive strength between 7 and 50 MPa at ambient temperature of laboratory. The properties of geopolymers were improved when elaborated with a mixture of volcanic ashes and metakaolin (ZD–MK and ZG–MK). For geopolymers obtained from ZD–MK, the setting time was between 500 and 160 minutes while it was between 220 and 125 minutes for geopolymers obtained from ZG–MK. The compressive strength greatly increased between 23 and 68 MPa and 39 and 64 MPa for geopolymers obtained from ZG –MK and ZD–MK respectively. A comparative study of the properties of mixtures of metakaolin–alumina and volcanic ash–alumina based geopolymers shows that metakaolin is a good source of Al2O3 and SiO2 and which highly reactive with alkaline solution and produces geopolymers with better characteristics compared to volcanic ash based–geopolymer. The properties of volcanic ash–based geopolymer were also improved when amorphous alumina was incorporated into the volcanic ash. This additive is used to compensate the deficiencies in Al2O3 content in the volcanic ash. Compare to when volcanic ash is used alone 20 to 40 % incorporation of this additive corresponded to increases of the compressive strength by 18.1 % for metakaolin-alumina based-geopolymers and by 32.4 % for volcanic ash-based geopolymers.

Prediction of water–rock interaction and porosity evolution in a granitoid-hosted enhanced geothermal system, using constraints from the 5 km Basel-1 well

Numerical simulations based on plans for a deep geothermal system in Basel, Switzerland are used here to understand chemical processes that occur in an initially dry granitoid reservoir during hydraulic stimulation and long-term water circulation to extract heat. An important question regarding the sustainability of such enhanced geothermal systems (EGS), is whether water–rock reactions will eventually lead to clogging of flow paths in the reservoir and thereby reduce or even completely block fluid throughput. A reactive transport model allows the main chemical reactions to be predicted and the resulting evolution of porosity to be tracked over the expected 30-year operational lifetime of the system. The simulations show that injection of surface water to stimulate fracture permeability in the monzogranite reservoir at 190 °C and 5000 m depth induces redox reactions between the oxidised surface water and the reduced wall rock. Although new calcite, chlorite, hematite and other minerals precipitate near the injection well, their volumes are low and more than compensated by those of the dissolving wall-rock minerals. Thus, during stimulation, reduction of injectivity by mineral precipitation is unlikely. During the simulated long-term operation of the system, the main mineral reactions are the hydration and albitization of plagioclase, the alteration of hornblende to an assemblage of smectites and chlorites and of primary K-feldspar to muscovite and microcline. Within a closed-system doublet, the composition of the circulated fluid changes only slightly during its repeated passage through the reservoir, as the wall rock essentially undergoes isochemical recrystallization. Even after 30 years of circulation, the calculations show that porosity is reduced by only ∼0.2%, well below the expected fracture porosity induced by stimulation. This result suggests that permeability reduction owing to water–rock interaction is unlikely to jeopardize the long-term operation of deep, granitoid-hosted EGS systems. A peculiarity at Basel is the presence of anhydrite as fracture coatings at ∼5000 m depth. Simulated exposure of the circulating fluid to anhydrite induces a stronger redox disequilibrium in the reservoir, driving dissolution of ferrous minerals and precipitation of ferric smectites, hematite and pyrite. However, even in this scenario the porosity reduction is at most 0.5%, a value which is unproblematic for sustainable fluid circulation through the reservoir.

River loads and modern denudation of the Alps — A review

This paper presents the first comprehensive analysis of sediment and dissolved load across an entire mountain range. We investigate patterns and rates of modern denudation of the European Alps based on a compilation of data about river loads and reservoir sedimentation from 202 drainage basins that are between ca. 1 to 10,000 km2 large. The study basins cover about 50% of the total area of the Alps. Modern glaciated basins have the highest sediment yields of up to 7000 t km− 2 a− 1, which are on average 5 to 10 times higher than in non-glaciated basins. Likewise sediment yield and glacial cover are positively correlated. Instead, relief is a relatively weak predictor of sediment yield. The strong glacial impact in the correlations is due to glacier recession since the 19th century as well as due to glacial conditioning during repeated Quaternary glaciations which have produced the strong transient state of the Alpine landscape. We suggest that this is the major cause for ca. 3 fold enhanced denudation of the western compared to the eastern Alps. Chemical denudation rates are highest in the external Alps dominated by carbonate sedimentary rocks, where they make up about one third of total denudation. The high rates cannot be explained without anhydrite dissolution. We estimated that only 45% of the sediments mobilized in headwaters are exported out off the Alps, most sediments being trapped in artificial reservoirs. The total amount of sediment annually trapped within the Alps equates to 43 Mt. When corrected for sediment storage, we obtain an area-weighted mean total denudation rate for the Alps of about 0.32 mm a− 1. The pre-dam rate might be as high as 0.42 mm a− 1. In total, ca. 35 plus 23 Mt of mass are exported each year out of the Alps as solids and solutes, respectively. These rates are not enough to out pace modern rock uplift. Nevertheless, pattern of sediment yield across the Alps coincides roughly with the intensity of glacial conditioning and modern rock uplift, supporting the hypothesis of an erosion-driven uplift of the Alps.

Predictive modelling of mineral scaling, corrosion and the performance of solute geothermometers in a granitoid-hosted, enhanced geothermal system

Experience is lacking with mineral scaling and corrosion in enhanced geothermal systems (EGS) in which surface water is circulated through hydraulically stimulated crystalline rocks. As an aid in designing EGS projects we have conducted multicomponent reactive-transport simulations to predict the likely characteristics of scales and corrosion that may form when exploiting heat from granitoid reservoir rocks at ∼200 °C and 5 km depth. The specifications of an EGS project at Basel, Switzerland, are used to constrain the model. The main water–rock reactions in the reservoir during hydraulic stimulation and the subsequent doublet operation were identified in a separate paper (Alt-Epping et al., 2013b). Here we use the computed composition of the reservoir fluid to (1) predict mineral scaling in the injection and production wells, (2) evaluate methods of chemical geothermometry and (3) identify geochemical indicators of incipient corrosion. The envisaged heat extraction scheme ensures that even if the reservoir fluid is in equilibrium with quartz, cooling of the fluid will not induce saturation with respect to amorphous silica, thus eliminating the risk of silica scaling. However, the ascending fluid attains saturation with respect to crystalline aluminosilicates such as albite, microcline and chlorite, and possibly with respect to amorphous aluminosilicates. If no silica-bearing minerals precipitate upon ascent, reservoir temperatures can be predicted by classical formulations of silica geothermometry. In contrast, Na/K concentration ratios in the production fluid reflect steady-state conditions in the reservoir rather than albite–microcline equilibrium. Thus, even though igneous orthoclase is abundant in the reservoir and albite precipitates as a secondary phase, Na/K geothermometers fail to yield accurate temperatures. Anhydrite, which is present in fractures in the Basel reservoir, is predicted to dissolve during operation. This may lead to precipitation of pyrite and, at high exposure of anhydrite to the circulating fluid, of hematite scaling in the geothermal installation. In general, incipient corrosion of the casing can be detected at the production wellhead through an increase in H2(aq) and the enhanced precipitation of Fe-bearing aluminosilicates. The appearance of magnetite in scales indicates high corrosion rates.

Interaction of corroding iron with bentonite in the ABM1 experiment at Äspö, Sweden: A microscopic approach

Bentonite and iron metals are common materials proposed for use in deep-seated geological repositories for radioactive waste. The inevitable corrosion of iron leads to interaction processes with the clay which may affect the sealing properties of the bentonite backfill. The objective of the present study was to improve our understanding of this process by studying the interface between iron and compacted bentonite in a geological repository-type setting. Samples of MX-80 bentonite samples which had been exposed to an iron source and elevated temperatures (up to 115ºC) for 2.5 y in an in situ experiment (termed ABM1) at the Äspö Hard Rock Laboratory, Sweden, were investigated by microscopic means, including scanning electron microscopy, μ-Raman spectroscopy, spatially resolved X-ray diffraction, and X-ray fluorescence. The corrosion process led to the formation of a ~100 mm thick corrosion layer containing siderite, magnetite, some goethite, and lepidocrocite mixed with the montmorillonitic clay. Most of the corroded Fe occurred within a 10 mm-thick clay layer adjacent to the corrosion layer. An average corrosion depth of the steel of 22–35 μm and an average Fe2+ diffusivity of 1–26×10–13 m2/s were estimated based on the properties of the Fe-enriched clay layer. In that layer, the corrosion-derived Fe occurred predominantly in the clay matrix. The nature of this Fe could not be identified. No indications of clay transformation or newly formed clay phases were found. A slight enrichment of Mg close to the Fe–clay contact was observed. The formation of anhydrite and gypsum, and the dissolution of some SiO2 resulting from the temperature gradient in the in situ test, were also identified. © 2014, Clay Minerals Society. All right reserved.

Heavy mineral content of ODP Leg 107 holes

Analyses of rock clasts and of heavy minerals in upper Miocene coarse detrital units drilled along the East Sardinia passive-type continental margin (Sites 654, 653, 652, and 656) reveal that the stretched basement contains quite complex rock suites. Taking also into account previous sampling data, in moving from west to east across the margin, the nature of the basement changes drastically. To the west there are mostly Hercynian basement rocks with their cover, referable to the alpine foreland of the Corsica-Sardinia block. To the east, along the lower margin, where crustal thinning is quite severe, the basement contains rock suites referable to a pre-upper Tortonian orogenized zone with units constituting parts of the Alpine and Apenninic chains (presumably with thickened continental crust prior to stretching). Largest thinning and ocean forming occurred then, in a rather short time, mostly at the expense of unstable crust just thickened by orogenetic/tectogenetic processes.

Chemistry of hot waters sampled from basaltic basement at DSDP Hole 83-504B

Seawater that has been altered by reaction with basaltic basement has been sampled from Deep Sea Drilling Project Hole 504B, located on 5.9-m.y.-old crust on the southern flank of the Costa Rica Rift. Fourteen water samples have been collected on Legs 69, 70, and 83, both before and after renewed drilling on the latter two legs, at temperatures from 69 to 133°C and pressures from 390 to 425 bars. The water sampled prior to renewed drilling on Leg 83 had occupied the hole for nearly 2 yr. since it was last flushed with surface seawater at the end of Leg 70. Despite some contamination by seawater during sampling, the composition of two of these waters has been determined by using nitrate as a tag for the contaminant. Both the 80 and 115°C waters have seawater chlorinity, but have lost considerable Mg, Na, K, sulfate, and 02, and have gained Ca, alkalinity, Si, NH3 and H2S. The loss of sulfate is due to anhydrite precipitation, as indicated by the d34S value of the remaining dissolved sulfate. The 87Sr/86Sr ratio has been lowered to 0.7086 for the 80°C water and 0.7078 for the 115°C water, whereas the Sr concentration is nearly unchanged. The changes in major element composition relative to seawater are also larger for the 115°C water, indicating that the basement formation water at this site probably varies in composition with depth. Based on their direction relative to seawater, the compositional changes for the 80 and 115°C waters do not complement the changes inferred for the altered rocks from Hole 504B, suggesting that the bulk composition of the altered rocks, like their mineralogy, is largely unrelated to the present thermal and alteration regime in the hole. The exact nature of the reacted seawaters cannot be determined yet, however. During its 2 yr. residence in the hole, the surface seawater remaining at the end of Leg 70 would have reacted with the wall rocks and exchanged with their interstitial formation waters by diffusion and possibly convection. How far these processes have proceeded is not yet certain, although calculations suggest that diffusion alone could have largely exchanged the surface seawater for interstitial water. The d18O of the samples is indistinguishable from seawater, however, and the d14C of the 80°C sample is similar to that of ocean bottom water. Although the interpretation of these species is ambiguous, that of tritium should not be. Tritium analyses, which are in progress, should clarify the nature of the reacted seawaters obtained from the hole.

Geochemistry of DSDP Hole 83-504B minerals

Leg 83 of the Deep Sea Drilling Project has deepened Hole 504B to over 1 km into basement, 1350 m below the seafloor (BSF). The hole previously extended through 274.5 m of sediment and 561.5 m of pillow basalts altered at low temperature (< 100°C), to 836 m BSF. Leg 83 drilling penetrated an additional 10 m of pillows, a 209-m transition zone, and 295 m into a sheeted dike complex. Leg 83 basalts (836-1350 m BSF) generally contain superimposed greenschist and zeolite-facies mineral parageneses. Alteration of pillows and dikes from 836 to 898 m BSF occurred under reducing conditions at low water/rock ratios, and at temperatures probably greater than 100°C. Evolution of fluid composition resulted in the formation of (1) clay minerals, followed by (2) zeolites, anhydrite, and calcite. Alteration of basalts in the transition zone and dike sections (898-1350 m BSF) occurred in three basic stages, defined by the opening of fractures and the formation of characteristic secondary minerals. (1) Chlorite, actinolite, pyrite, albite, sphene, and minor quartz formed in veins and host basalts from partially reacted seawater (Mg-bearing, locally metal-and Si-enriched) at temperatures of at least 200-250°C. (2) Quartz, epidote, and sulfides formed in veins at temperatures of up to 380°C, from more evolved (Mg-depleted, metal-, Si-, and 18O-enriched) fluids. (3) The last stage is characterized by zeolite formation: (a) analcite and stilbite formed locally, possibly at temperatures less than 200°C followed by (b) formation of laumontite, heulàndite, scolecite, calcite, and prehnite from solutions depleted in Mg and enriched in Ca and 18O, at temperatures of up to 250°C. The presence of small amounts of anhydrite locally may be due to ingress of relatively unaltered seawater into the system during Stage 3. Alteration was controlled by the permeability of the crust and is characterized by generally incomplete recrystallization and replacement reactions among secondary minerals. Secondary mineralogy in the host basalts is strongly controlled by primary mineralogy. The alteration of Leg 83 basalts can be interpreted in terms of an evolving hydrothermal system, with (a) changes in solution composition because of reaction of seawater fluids with basalts at high temperatures; (b) variations in permeability caused by several stages of sealing and reopening of cracks; and (c) a general cooling of the system, caused either by the cooling of a magma chamber beneath the spreading center and/or the movement of the crust away from the heat source. The relationship of the high-temperature alteration in the transition zone and dike sections to the low-temperature alteration in the overlying pillow section remains uncertain.

Geochemistry and mineralogy of Eocene-Oligocene sediments of IODP Hole 302-M0002A

In 2004, Integrated Ocean Drilling Program Expedition 302 (Arctic Coring Expedition, ACEX) to the Lomonosov Ridge drilled the first Central Arctic Ocean sediment record reaching the uppermost Cretaceous (~430 m composite depth). While the Neogene part of the record is characterized by grayish-yellowish siliciclastic material, the Paleogene part is dominated by biosiliceous black shale-type sediments. The lithological transition between Paleogene and Neogene deposits was initially interpreted as a single sedimentological unconformity (hiatus) of ~26 Ma duration, separating Eocene from Miocene strata. More recently, however, continuous sedimentation on Lomonosov Ridge throughout the Cenozoic was proclaimed, questioning the existence of a hiatus. In this context, we studied the elemental and mineralogical sediment composition around the Paleogene-Neogene transition at high resolution to reconstruct variations in the depositional regime (e.g. wave/current activity, detrital provenance, and bottom water redox conditions). Already below the hiatus, mineralogical and geochemical proxies imply drastic changes in sediment provenance and/or weathering intensity in the hinterland, and point to the existence of another, earlier gap in the sediment record. The sediments directly overlying the hiatus (the Zebra interval) are characterized by pronounced and abrupt compositional changes that suggest repeated erosion and re-deposition of material. Regarding redox conditions, euxinic bottom waters prevailed at the Eocene Lomonosov Ridge, and became even more severe directly before the hiatus. With detrital sedimentation rates decreasing, authigenic trace metals were highly enriched in the sediment. This continuous authigenic trace metal enrichment under persistent euxinia implies that the Arctic trace metal pool was renewed continuously by water mass exchange with the world ocean, so the Eocene Arctic Ocean was not fully restricted. Above the hiatus, extreme positive Ce anomalies are clear signs of a periodically well-oxygenated water column, but redox conditions were highly variable during deposition of the Zebra interval. Significant Mn enrichments only occur above the Zebra interval, documenting the Miocene establishment of stable oxic conditions in the Arctic Ocean. In summary, extreme and abrupt changes in geochemistry and mineralogy across the studied sediment section do not suggest continuous sedimentation at the Lomonosov Ridge around the Eocene-Miocene transition, but imply repeated periods of very low sedimentation rates and/or erosion.

Isotopic and chemical compositions of rocks and minerals from the TAG hydrothermal mound, ODP Site 957

Strontium- and oxygen-isotopic measurements of samples recovered from the Trans-Atlantic Geotraverse (TAG) hydrothermal mound during Leg 158 of the Ocean Drilling Program provide important constraints on the nature of fluid-rock interactions during basalt alteration and mineralization within an active hydrothermal deposit. Fresh Mid-Ocean Ridge Basalt (MORB), with a 87Sr/86Sr of 0.7026, from the basement beneath the TAG mound was altered at both low and high temperatures by seawater and altered at high temperature by near end-member black smoker fluids. Pillow breccias occurring beneath the margins of the mound are locally recrystallized to chlorite by interaction with large volumes of conductively heated seawater (>200°C). The development of a silicified, sulfide-mineralized stockwork within the basaltic basement follows a simple paragenetic sequence of chloritization followed by mineralization and the development of a quartz+pyrite+paragonite stockwork cut by quartz-pyrite veins. Initial alteration involved the development of chloritic alteration halos around basalt clasts by reaction with a Mg-bearing mixture of upwelling, high-temperature (>300°C), black smoker-type fluid with a minor (<10%) proportion of seawater. Continued high-temperature (>300°C) interaction between the wallrock and these Mg-bearing fluids results in the complete recrystallization of the wallrock to chlorite+quartz+pyrite. The quartz+pyrite+paragonite assemblage replaces the chloritized basalts, and developed by reaction at 250-360°C with end-member hydrothermal fluids having 87Sr/86Sr ~0.7038, similar to present-day vent fluids. The uniformity of the 87Sr/86Sr ratios of hydrothermal assemblages throughout the mound and stockwork requires that the 87Sr/86Sr ratio of end-member hydrothermal fluids has remained relatively constant for a time period longer than that required to change the interior thermal structure and plumbing network of the mound and underlying stockwork. Precipitation of anhydrite in breccias and as late-stage veins throughout most of the mound and stockwork, down to at least 125 mbsf, records extensive entrainment of seawater into the hydrothermal deposit. 87Sr/86Sr ratios indicate that most of the anhydrite formed from ~2:1 mixture of seawater and black smoker fluids (65%±15% seawater). Oxygen-isotopic compositions imply that anhydrite precipitated at temperatures between 147°C and 270°C and require that seawater was conductively heated to between 100°C and 180°C before mixing and precipitation occurred. Anhydrite from the TAG mound has a Sr-Ca partition coefficient Kd ~0.60±0.28 (2 sigma). This value is in agreement with the range of experimentally determined partition coefficients (Kd ~0.27-0.73) and is similar to those calculated for anhydrite from active black smoker chimneys from 21°N on the East Pacific Rise. The d18O (for SO4) of TAG anhydrite brackets the value of seawater sulfate oxygen (~9.5?). Dissolution of anhydrite back into the oceans during episodes of hydrothermal quiescence provides a mechanism of buffering seawater sulfate oxygen to an isotopically light composition, in addition to the precipitation and dissolution of anhydrite within the oceanic basement during hydrothermal recharge at the mid-ocean ridges.

Mineralogy and geochemistry at DSDP Leg 80 Holes

Cenozoic sediments recovered from Sites 548, 549, and 550 were the objects of mineralogical (bulk sample and <2 - µm fraction) and geochemical (HCl extract) studies. Thin sections of rock pebbles embedded in sediments (upper levels at Site 548, particularly) were examined on a polarizing microscope. This study outlines the vertical and lateral variation and evolution of the sedimentation. In the Paleocene and lower Eocene, the clay fraction is abundant and smectite is practically the sole existing clay mineral. High Mn, Al, Fe, Mg, and K contents were measured in HCl extracts. Through the middle Eocene, carbonates become more abundant - highly dominant at Site 548. Metal contents in HCl extracts are very low. The clay fraction, although dominated at all sites by smectites, becomes richer in illite and poorly crystallized chlorite. At the middle/upper Miocene boundary, a significant decrease in the smectite/(illite + chlorite) ratio occurs at all sites, and this decrease continues into the middle Pliocene. This decrease is marked by an abrupt increase of quartz at Site 548. At the two other sites, carbonates remain highly predominant; HCl extracts reflect the relative abundance of the clay and carbonate fractions. After a brief recurrence of smectite in a high-metal-content interval, illite and chlorite become the dominant clay minerals in the upper Pliocene and the Pleistocene, where numerous variations in mineralogical composition occur in the clay fraction (Sites 548 and 549) or in non-clay components (Site 548). Several pebbles of various nature and origin, encountered in different levels of this interval at Site 548, appear to have an ice-rafting origin. This study points out three main breaks in the general evolution of the sedimentation: the first, corresponding to the lower/middle Eocene boundary, is marked by the increase of carbonates and associated elements; the second, corresponding to the middle/upper Miocene boundary, is marked by a major decrease of the smectite/(illite + chlorite) ratio at all sites and by a massive appearance of quartz at Site 548; and the third, which occurred toward the late Pliocene, is marked by the dominance of primary clay minerals and the arrival of ice-rafted pebbles. Our interpretation of results considers paleohydrological and paleoclimatic phenomena. It is suggested that the major middle/late Miocene break was associated with an increase of the deep bottom-water circulation between the Norwegian Sea and the North Atlantic Ocean, and/or a climatic evolution: humidification and cooling of climate. The changes toward the late Pliocene appear to have been the first effects of the glaciations at the end of Cenozoic.

Messinian and pre-Messinian sediments of ODP Holes 107-652A and 107-654A

Sedimentology, mineralogy, and petrology of the pre-Pliocene sediments drilled at ODP Sites 652 and 654 in the Tyrrhenian Sea (Leg 107) have been studied with emphasis on the lower Messinian to pre-Messinian intervals. Messinian at Site 652 is essentially turbiditic and basinal in character; it was deposited during the syn-rift phase in a strongly subsiding half-graben and is correlatable with emerged coeval sequences; in part with the Laga Formation of the foredeep of Apennines, and in part with the filling of grabens dissecting that chain in the Tyrrhenian portion of Tuscany. The sequence found in Site 654 indicates an upper Tortonian to Messinian transgression accompanying crustal stretching in the western Tyrrhenian Sea and is perfectly correlatable with the so-called "Sahelian cycle" and with "postorogenic" cycles recognized in peninsular Italy and in Sicily.

Strontium concentrations and isotopic compositions of anhydrites from the TAG active mound

Sr isotope analyses have been conducted on anhydrite samples from the TAG (Trans-Atlantic Geotraverse) active hydrothermal mound (26°08?N, Mid-Atlantic Ridge) that have previously been shown to exhibit two distinct patterns of REE behavior when normalized to TAG end-member hydrothermal fluid. Despite differences in REE patterns, the Sr isotope data indicate that all the anhydrites precipitated from fluids with a similar range of hydrothermal fluid and seawater components, and all but one were seawater-dominated (52%-75%). Speciation calculations using the EQ3/6 software package for geochemical modeling of aqueous systems suggest that the REE complexation behavior in different fluid mixing scenarios can explain the variations in the REE patterns. Anhydrites that exhibit relatively flat REE patterns [(La_bs)/(Yb_bs) = 0.8-2.0; subscript bs indicates normalization to end-member black smoker hydrothermal fluid] and a small or no Eu anomaly [(Eu_bs)/(Eu*_bs) = 0.8-2.0] are inferred to have precipitated from mixes of end-member hydrothermal fluid and cold seawater. REE complexes with hard ligands (e.g., fluoride and chloride) are less stable at low temperatures and trivalent Eu has an ionic radius similar to that of Ca2+ and the other REE, and so they behave coherently. In contrast, anhydrites that exhibit slight LREE-depletion [(La_bs)/(Yb_bs) = 0.4-1.4] and a distinct negative anomaly [(Eu_bs)/(Eu*_bs) = 0.2-0.8] are inferred to have precipitated from mixes of end-member hydrothermal fluid and conductively heated seawater. The LREE depletion results from the presence of very stable LREE chloro-complexes that effectively limit the availability of the LREE for partitioning into anhydrite. Above 250°C, Eu is present only in divalent form as chloride complexes, and discrimination against Eu2+ is likely due to both the mismatch in ionic radii between Eu2+ and Ca2+, and the strong chloro-complexation of divalent Eu which promotes stability in the fluid and inhibits partitioning of Eu2+ into precipitating anhydrite. These variations in REE behavior attest to rapid fluctuations in thermal regime, fluid flow and mixing in the subsurface of the TAG mound that give rise to heterogeneity in the formation conditions of individual anhydrite crystals.