Análise de um queimador infravermelho funcionando com combustível híbrido : GLP/Bio-óleo

Biomass is considered the largest renewable energy source that can be used in an environmentally sustainable. From the pyrolysis of biomass is possible to obtain products with higher energy density and better use properties. The liquid resultant of this process is traditionally called bio-oil. The use of infrared burners in industrial applications has many advantages in terms of technical-operational, for example, uniformity in the heat supply in the form of radiation and convection, with a greater control of emissions due to the passage of exhaust gases through a macroporous ceramic bed. This paper presents a commercial infrared burner adapted with an ejector proposed able to burn a hybrid configuration of liquefied petroleum gas (LPG) and bio-oil diluted. The dilution of bio-oil with absolute ethanol aimed to decrease the viscosity of the fluid, and improving the stability and atomization. It was introduced a temperature controller with thermocouple modulating two stages (low heat / high heat), and solenoid valves for fuels supply. The infrared burner has been tested, being the diluted bio-oil atomized, and evaluated its performance by conducting energy balance. The method of thermodynamic analysis to estimate the load was used an aluminum plate located at the exit of combustion gases and the distribution of temperatures measured by thermocouples. The dilution reduced the viscosity of the bio-oil in 75.4% and increased by 11% the lower heating value (LHV) of the same, providing a stable combustion to the burner through the atomizing with compressed air and burns combined with LPG. Injecting the hybrid fuel there was increase in the heat transfer from the plate to the environment in 21.6% and gain useful benefit of 26.7%, due to the improved in the efficiency of the 1st Law of Thermodynamics of infrared burner

Produção de biomassa e composição química de adubos verdes cultivados no Vale do Ribeira

The contribution of green manure to soil improvement and crop production depends primarily on biomass production and its chemical composition, which vary depending on the species, region and growing season. The aim of this research was to evaluate the chemical composition of biomass produced by green manures in Vale do Ribeira, São Paulo, Brazil. In order to develop this research, was carried an experiment in Pariquera-Acu, in 2006/2007, in completely randomized blocks design with four treatments (three green manure and spontaneous vegetation) and five replications. At 30, 60, 90 and 120 after sowing samples were collected in 1m(2) of the shoots and determined fresh and dry, and chemical composition biomass. Sunhemp, pigeon pea and mucuna produced, in decreasing order, the largest quantities of biomass and were more efficient than the spontaneous vegetation. The biomass produced by green manure had higher quality than that produced by spontaneous vegetation. Sunhemp and pigeon pea have a higher proportion of dry matter in stems which have low N, high C/N and L/N ratio, variables indicating slow decomposition of residues. The analysis of dry matter partitioned to better indication of the chemical composition of the residues and the prevision of the availability of nutrients in the soil.

Análise do Crescimento de Hyptis suaveolens

O crescimento de H. suaveolens foi estudado em casa de vegetação, no delineamento experimental inteiramente casualizado, com quatro repetições. As plantas cresceram em vasos com capacidade de cinco litros, preenchidos com areia e irrigados com solução nutritiva, diariamente. Os atributos de crescimento das plantas foram avaliados dos 20 até os 160 dias após a emergência (DAE) da planta daninha, em intervalos regulares de 14 dias. A planta atingiu o máximo estimado de biomassa seca acumulada aos 145 DAE. A partir da emergência, até 104 dias, as folhas apresentaram maior participação no acúmulo de biomassa seca total da planta; posteriormente, os caules passaram a deter maior proporção dessa característica. A taxa de assimilação líquida foi crescente do início do ciclo até a época estimada de 71 DAE, decrescendo a seguir, provavelmente devido ao auto-sombreamento das folhas. A análise do crescimento indicou que H. suaveolens pode apresentar alta capacidade competitiva, podendo ser considerada planta infestante de crescimento tardio, quando presente nas culturas anuais de verão.

Remoção mecânica de plantas aquáticas: análise econômica e operacional

A remoção de plantas aquáticas tem sido utilizada como opção ao controle químico e biológico, em razão de restrições ambientais em algumas regiões brasileiras. O objetivo deste trabalho foi desenvolver um modelo para análise econômica e operacional da remoção mecânica de plantas aquáticas, visando realizar estudo econômico comparativo com o controle químico. A operação foi estudada num reservatório de uma usina de bombeamento em Barra do Piraí-RJ. O sistema consiste de retroescavadeiras instaladas em balsas, usadas para cortar as plantas e liberá-las no fluxo de água. Antes da tomada d'água existe uma barreira flutuante que intercepta as plantas, as quais são removidas por um guindaste fixo nas margens. As plantas são armazenadas por algum tempo e depois descartadas. Existe, ainda, um sistema de limpeza das grades da tomada d'água. Dados do volume total de plantas descartadas foram coletados durante 14 meses, assim como foi avaliado o volume de biomassa produzido por área das principais espécies infestantes. A empreiteira que administra o serviço forneceu planilhas de custos e outro parâmetros operacionais. Um modelo foi desenvolvido para calcular custos por hectare de plantas removidas. Os resultados mostraram custo médio mensal de US$ 17.780,28 por hectare. Apesar do alto custo, o sistema de remoção demonstrou capacidade de controlar apenas 4,1% da área infestada no reservatório, na época da coleta dos dados. Simulando dados de uma aplicação de glyphosate, o controle químico custaria apenas 0,23% do custo da remoção. Análises de sensibilidade mostraram que a compactação das plantas para transporte, o volume de plantas produzidas por área e o custo do transporte são os parâmetros principais para a otimização.

Cobertura do solo, produção de biomassa e teores de Mn e Zn de alface no sistema orgânico

O objetivo deste trabalho foi avaliar o efeito da cobertura do solo com aveia preta e manutenção da palha sobre o terreno, bem como cobertura do solo com filme de polietileno preto, sobre a produção de biomassa e teores de Mn e Zn em alface cultivada no sistema orgânico, por dois anos consecutivos. Utilizaram-se cinco tratamentos: solo sem cobertura, coberto com filme de polietileno preto, coberto com aveia acamada, coberto com aveia ceifada e solo coberto com aveia na sua forma natural, para o cultivo de três cultivares de alface. O experimento seguiu delineamento experimental de blocos ao acaso, com quatro repetições e análise estatística com parcelas subdivididas. Concluiu-se que o cultivo de alface em sucessão à aveia preta, sobre a palha, promoveu produção satisfatória e apresentou adequados teores de manganês e zinco, equivalentes àqueles encontrados na literatura em diferentes sistemas de cultivo, e a cobertura do solo com plástico preto promoveu produção satisfatória com maior acúmulo de Zn no primeiro ano e menor de Mn no segundo.

Efeito da adubação fosfata sobre o acúmulo de biomassa e teor de brix de duas variedades de cana-de-açúcar

The objective of this study was to evaluate the accumulation of matter, dry matter content of Brix and two varieties of sugar cane, influenced by the phosphorus cultivated on "Zona da Mata" region, State of Alagoas. The experiment, a factorial 2 x 6, was composed of two varieties of cane; RB867515 and RB92579 and six phosphorus levels: zero, 30, 60, 90, 120 and 150 kg ha(-1), with the source of the phosphorus triple superphosphate. Was also used nitrogen and potassium in doses equivalent to 100 and 200 kg ha(-1) and K, respectively. The soil of the experimental area was set to raise the base saturation to 60%. At the beginning of the first rainfall of the rainy season of 2006 was performed with micro fertilization in coverage, in doses equivalent to 6,0; 6,0 and 7,0 kg ha(-1) of Cu, Zn and Mn, respectively. Was The chemical control of weeds. Every month, from August to October 2006, samples were collected in the cane plant. There was initially the number of plants m(2), followed by weighing the material. It was subsequently withdrawn a subsample containing ten plants for weighing. After weighing the material was passed in horsemanship and homogenized, again drew up a sample of approximately 300g, leading them to forced ventilation oven at 65 degrees C, toobtain constant weight. Resulting in the production of natural (MN) and dry matter (DM). In July, we analyzed the levels of Brix% juice in the refractometer Brix. The average values of production of natural (MN), dry matter (DM) and contents of Brix% were subjected to analysis of variance and regression for variables. The accumulation of dry matter and were influenced by fertilization. The contents of Brix% in two varieties did not suffer significant influence of fertilization.

Teores de metais na biomassa de Egeria densa, Egeria najas e Ceratophyllum demersum

Este estudo foi realizado com o objetivo de se estimar o conteúdo de elementos metálicos presentes em três macrófitas aquáticas submersas, procurando avaliar a participação destas plantas na remoção destes elementos na água e criar base de dados que permita prever o impacto ambiental do descarte delas em solo ou na própria água. As amostras foram desidratadas, moídas e encaminhadas aos laboratórios para análise e quantificação dos elementos. Para as três espécies, a maior concentração de elementos foi observada durante o verão, ocorrendo declínio nas concentrações durante o inverno, principalmente para os elementos vanádio e chumbo. Não foi detectada presença do elemento mercúrio em nenhuma das amostras.

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós (euphorbia tirucalli Linn)

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Extração e análise da fração lipídica da microalga monoraphidium sp., síntese e caracterização do seu biodiesel

The cultivation of microalgae biomass in order to produce biodiesel arises as an extremely promising aspect, in that the microalgae culture includes short cycle of reproduction, smaller areas for planting and residual biomass rich in protein content. The present dissertation evaluates the performance and features, through spectrometry in the region of infrared with transformed Fourier (FTIR) and spectrometry in the region of UVvisible (UV-Vis), of the extracted lipid material (LM) using different techniques of cell wall disruption (mechanical agitation at low and at high spin and agitation associated with cavitation). The technique of gas chromatography (GC) brought to light the success of alkaline transesterification in the conversion of oil into methyl monoesters (MME), which was also analyzed by spectroscopic techniques (FTIR, proton magnetic resonance (1H NMR) and carbon (13C NMR). Through thermogravimetric analysis (TGA) were analyzed the lipid material (LM), biodiesel and the microalgae biomass. The method which provided the best results concerning the efficiency in extraction of the LP of Monoraphidium sp. (12,51%) was by mechanical agitation at high spin (14 000 rpm), for 2 hours being the ideal time, as shown by the t test. The spectroscopic techniques (1H NMR, 13C NMR and FTIR) confirmed that the structure of methyl monoesters and the chromatographic data (CG) revealed a high content of saturated fatty acid esters (about 70%) being the major constituent eicosanoic acid (33,7%), which justifies the high thermal stability of microalgae biodiesel. The TGA also ratified the conversion rate (96%) of LM into MME, pointing out the quantitative results compatible with the values obtained through GC (about 98%) and confirmed the efficiency of the extraction methods used, showing that may be a good technique to confirm the extraction of these materials. The content of LM microalgae obtained (12,51%) indicates good potential for using such material as a raw material for biodiesel production, when compared to oil content which can be obtained from traditional oil for this use, since the productivity of microalgae per hectare is much larger and requires an extremely reduced period to renew its cultivation

Aplicação de dessecantes na cultura de soja: teor de umidade nas sementes e biomassa nas plantas

Os objetivos deste trabalho foram avaliar a eficácia dos dessecantes e determinar a melhor época de aplicação na cultura de soja. O delineamento experimental utilizado foi em blocos casualizados, estando os tratamentos dispostos em esquema fatorial 3x3 e 4x4 de produtos (dessecantes) e épocas de aplicação, nos anos agrícolas 1996/97 e 1997/98, respectivamente. Os dessecantes utilizados foram: paraquat, diquat e paraquat + diquat em 1996/97 e paraquat, diquat, paraquat + diquat e glufosinato de amônio em 1997/98, respectivamente nas dosagens de 0,4, 0,3 e 0,2 + 0,15; e 0,4, 0,3, 0,2 + 0,15 e 0,4 kg i.a. ha¹. Como épocas, foram realizadas três aplicações em 1996/97 e quatro em 1997/98, com intervalos de cinco dias a partir do estádio R6. Após análise e interpretação dos resultados, concluiu-se que os dessecantes foram eficazes na dessecação e que o teor de umidade das sementes entre 50 e 60%, as plantas com baixa incidência de vagens amarelas e marrons e a relação peso de biomassa verde de vagens/biomassa verde total de cerca de 0,5 foram características marcantes na determinação da melhor época de aplicação dos dessecantes.

Análise de crescimento em Heteranthera reniformis, sob diferentes teores de Ca, Mg e S

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Recuperação de solos degradados na exploração mineral de cassiterita: biomassa microbiana e atividade da desidrogenase

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise de dificuldades técnicas e econômicas na inserção da cogeração pelas usinas sucroalcooleiras

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Produção de biomassa, rendimento e composição do óleo essencial de manjericão (Ocimum basilicum L.) em função de reguladores vegetais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)