Lordoplasty: midterm outcome of an alternative augmentation technique for vertebral fractures.

OBJECTIVE Vertebroplasty and balloon kyphoplasty are effective treatment options for osteoporotic vertebral compression fractures but are limited in correction of kyphotic deformity. Lordoplasty has been reported as an alternative, cost-effective, minimally invasive, percutaneous cement augmentation technique with good restoration of vertebral body height and alignment. The authors report on its clinical and radiological midterm results. METHODS A retrospective review was conducted of patients treated with lordoplasty from 2002 to 2014. Inclusion criteria were clinical and radiological follow-up evaluations longer than 24 months. Radiographs were accessed regarding initial correction and progressive loss of reduction. Complications and reoperations were recorded. Actual pain level, pain relief immediately after surgery, autonomy, and subjective impression of improvement of posture were assessed by questionnaire. RESULTS Sixty-five patients (46 women, 19 men, age range 38.9-86.2 years old) were treated with lordoplasty for 69 vertebral compression and insufficiency fractures. A significant correction of the vertebral kyphotic angle (mean 13°) and segmental kyphotic angle (mean 11°) over a mean follow-up of 33 months (range 24-108 months) was achieved (p < 0.001). On average, pain was relieved to 90% of the initial pain level. In 24% of the 65 patients a second spinal intervention was necessary: 16 distant (24.6%) and 7 adjacent (10.8%) new osteoporotic fractures, 4 instrumented stabilizations (6.2%), 1 new adjacent traumatic fracture (1.5%), and 1 distant microsurgical decompression (1.5%). Cement leakage occurred in 10.4% but was only symptomatic in 1 case. CONCLUSIONS Lordoplasty appeared safe and effective in midterm pain alleviation and restoration of kyphotic deformity in osteoporotic compression and insufficiency fractures. The outcomes of lordoplasty are consistent with other augmentation techniques.

Emissions of polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) from a cement kiln using a continuous monitoring system

Resumen de la comunicación presentada en PIC2015 – the 14th International Congress on Combustion By-Products and Their Health Effects, Umeå, Sweden, 14-17 June 2015.

The durability of cement bound minestone

The demand for road making materials continues to pressurise the supply of traditional good quality aggregates. Over the years, therefore, consideration has been given to alternative materials including industrial wastes. This thesis is concerned with potential use of Minestone, the by-product of coal mining, for the lower structural layers of pavement construction. Because of their clay like nature, Minestones do not merit consideration for such applications in an unbound state and, therefore, some form of stabilisation is necessary. Previous research has demonstrated that certain cement bound minestones, containing between 5 and 10 per cent cement, satisfy current Department of Transport requirements for use in pavement construction and, furthermore, they are not frost susceptible. However, doubts concerning the durability of cement bound minestones still remain. The thesis includes a review of both the cement and lime stabilisation techniques and also traces the origin and development of the methods used to assess the quality and durability of stabilised materials. An experimental study is described in which cement bound minestone specimens were subjected to a programme of tests which examined compressive strength, resistance to immersion, and resistance to freezing and thawing. The results of the tests were related to the properties of the raw materials. It was discovered that the response to cement stabilisation was governed mainly by the source of the minestone and, to a lesser degree, the cement content. It was also found that resistance in the durability tests was generally improved when the initial moisture content was raised above the optimum value. The result suggest that current methods for assessing cement stabilised materials are not appropriate to cement bound minestones. Alternative methods and criteria, based on volume change and retained strength following immersion and freeze-thaw tests, have been proposed. It is believed that these methods and criteria should also apply to other cement bound materials.

Experimental studies on comparison of microwave curing and thermal curing of epoxy resins used for alternative mould materials

In this present work attempts have been made to study the glass transition temperature of alternative mould materials by using both microwave heating and conventional oven heating. In this present work three epoxy resins, namely R2512, R2515 and R2516, which are commonly used for making injection moulds have been used in combination with two hardeners H2403 and H2409. The magnetron microwave generator used in this research is operating at a frequency of 2.45 GHz with a hollow rectangular waveguide. In order to distinguish the effects between the microwave and conventional heating, a number of experiments were performed to test their mechanical properties such as tensile and flexural strengths. Additionally, differential scanning calorimeter technique was implemented to measure the glass transition temperature on both microwave and conventional heating. This study provided necessary evidences to establish that microwave heated mould materials resulted with higher glass transition temperature than the conventional heating. Finally, attempts were also made to study the microstructure of microwave-cured materials by using a scanning electron microscope in order to analyze the morphology of cured specimens.

Open Source Enterprise Systems: Towards a Viable Alternative

Enterprise systems are located within the antinomy of appearing as generic product, while being means of multiple integrations for the user through configuration and customisation. Technological and organisational integrations are defined by architectures and standardised interfaces. Until recently, technological integration of enterprise systems has been supported largely by monolithic architectures that were designed, and maintained by the respective developers. From a technical perspective, this approach had been challenged by the suggestion of component-based enterprise systems that would allow for a more user-focused system through strict modularisation. Lately, the product nature of software as proprietary item has been questioned through the rapid increase of open source programs that are being used in business computing in general, and also within the overall portfolio that makes up enterprise systems. This suggests the potential for altered technological and commercial constellations for the design of enterprise systems, which are presented in different scenarios. The technological and commercial decomposition of enterprise software and systems may also address some concerns emerging from the users’ experience of those systems, and which may have arisen from their proprietary or product nature.

User-Generated Content als Qualitätsmedium? Alternative Anreize für Qualitätscontent

Angetrieben und unterstützt durch Web-2.0-Technologien, gibt es heute einen Trend zur Verbindung der Nutzung und Produktion von Inhalten als Produtzung (engl. produsage ). Um dabei die Qualität der erstellten Inhalte und eine nachhaltige Teilnahme der Nutzer sicherzustellen, müsen vier grundlegende Prinzipien eingehalten werden: * Größtmögliche Offenheit. * Ankurbeln der Gemeinschaft durch Inhalte und Hilfsmittel. * Unterstützung der Gruppendynamik und Abtretung von Verantwortung. * Keine Ausbeutung der Gemeinschaft und ihrer Arbeit.