Entwicklung, Aufbau und Messungen eines schnellen Eiskeimzählers

Im Rahmen dieser Arbeit wurde ein neuer Eiskeimzähler FINCH (Fast Ice Nucleus CHamber) entwickelt und erste Messungen von verschiedenen Testaerosolen im Labor und atmosphärischem Aerosol durchgeführt. Die Aerosolpartikel bzw. Ice Nuclei IN werden bei Temperaturen unter dem Gefrierpunkt und Übersättigungen in Bezug auf Eis zum Anwachsen zu Eiskristallen gebracht, um sie mittels optischer Detektion zu erfassen. In FINCH ist dies durch das Prinzip der Mischung realisiert, wodurch eine kontinuierliche Messung der IN-Anzahlkonzentration gewährleistet ist. Hierbei kann mit sehr hohen Sammelflussraten von bis zu 10 l/min gemessen werden. Ebenso ist ein schnelles Abfahren von verschiedenen Sättigungsverhältnissen in Bezug auf Eis in einem weiten Bereich von 0.9 - 1.7 bei konstanten Temperaturen bis zu −23 °C möglich. Die Detektion der Eiskristalle und damit der Bestimmung der IN-Anzahlkonzentration erfolgt über einen neu entwickelten optischen Sensor basierend auf der unterschiedlichen Depolarisation des zurückgestreuten Lichtes von Eiskristallen und unterkühlten Tropfen. In Labermessungen wurden Aktivierungstemperatur und -sättigungsverhältnis von Silberjodid AgI und Kaolinit vermessen. Die Resultate zeigten gute Übereinstimmungen mit Ergebnissen aus der Literatur sowie Parallelmessungen mit FRIDGE (FRankfurt Ice Deposition freezinG Experiment). FRIDGE ist eine statische Diffusionskammer zur Aktivierung und Auszählung von Eiskeimen, die auf einem Filter gesammelt wurden. Bei atmosphärischen Messungen auf dem Jungfraujoch(Schweiz) lagen die IN-Anzahlkonzentrationen mit bis zu 4 l−1 im Rahmen der aus der Literatur bekannten Werte. Messungen der Eiskristallresiduen von Mischwolken zeigten hingegen, dass nur jedes tausendste als Eiskeim im Depositionsmode aktiv ist. Hier scheinen andere Gefrierprozesse und sekundäre Eiskristallbildung von sehr großer Bedeutung für die Anzahlkonzentration der Eiskristallresiduen zu sein. Eine weitere Messung von atmosphärischem Aerosol in Frankfurt zeigte IN-Anzahlkonzentrationen bis zu 30 l−1 bei Aktivierungstemperaturen um −14 °C. Die parallele Probenahme auf Siliziumplättchen für die Messungen der IN-Anzahlkonzentration in FRIDGE ergaben Werte im gleichen Anzahlkonzentrationsbereich.

Numerical simulations of microphysical processes in pyro-convective clouds

Hochreichende Konvektion über Waldbränden ist eine der intensivsten Formen von atmosphärischer Konvektion. Die extreme Wolkendynamik mit hohen vertikalen Windgeschwindigkeiten (bis 20 m/s) bereits an der Wolkenbasis, hohen Wasserdampfübersättigungen (bis 1%) und die durch das Feuer hohen Anzahlkonzentration von Aerosolpartikeln (bis 100000 cm^-3) bilden einen besonderen Rahmen für Aerosol-Wolken Wechselwirkungen.Ein entscheidender Schritt in der mikrophysikalischen Entwicklung einer konvektiven Wolke ist die Aktivierung von Aerosolpartikeln zu Wolkentropfen. Dieser Aktivierungsprozess bestimmt die anfängliche Anzahl und Größe der Wolkentropfen und kann daher die Entwicklung einer konvektiven Wolke und deren Niederschlagsbildung beeinflussen. Die wichtigsten Faktoren, welche die anfängliche Anzahl und Größe der Wolkentropfen bestimmen, sind die Größe und Hygroskopizität der an der Wolkenbasis verfügbaren Aerosolpartikel sowie die vertikale Windgeschwindigkeit. Um den Einfluss dieser Faktoren unter pyro-konvektiven Bedingungen zu untersuchen, wurden numerische Simulationen mit Hilfe eines Wolkenpaketmodells mit detaillierter spektraler Beschreibung der Wolkenmikrophysik durchgeführt. Diese Ergebnisse können in drei unterschiedliche Bereiche abhängig vom Verhältnis zwischen vertikaler Windgeschwindigkeit und Aerosolanzahlkonzentration (w/NCN) eingeteilt werden: (1) ein durch die Aerosolkonzentration limitierter Bereich (hohes w/NCN), (2) ein durch die vertikale Windgeschwindigkeit limitierter Bereich (niedriges w/NCN) und (3) ein Übergangsbereich (mittleres w/NCN). Die Ergebnisse zeigen, dass die Variabilität der anfänglichen Anzahlkonzentration der Wolkentropfen in (pyro-) konvektiven Wolken hauptsächlich durch die Variabilität der vertikalen Windgeschwindigkeit und der Aerosolkonzentration bestimmt wird. rnUm die mikrophysikalischen Prozesse innerhalb der rauchigen Aufwindregion einer pyrokonvektiven Wolke mit einer detaillierten spektralen Mikrophysik zu untersuchen, wurde das Paketmodel entlang einer Trajektorie innerhalb der Aufwindregion initialisiert. Diese Trajektore wurde durch dreidimensionale Simulationen eines pyro-konvektiven Ereignisses durch das Model ATHAM berechnet. Es zeigt sich, dass die Anzahlkonzentration der Wolkentropfen mit steigender Aerosolkonzentration ansteigt. Auf der anderen Seite verringert sich die Größe der Wolkentropfen mit steigender Aerosolkonzentration. Die Reduzierung der Verbreiterung des Tropfenspektrums stimmt mit den Ergebnissen aus Messungen überein und unterstützt das Konzept der Unterdrückung von Niederschlag in stark verschmutzen Wolken.Mit Hilfe des Models ATHAM wurden die dynamischen und mikrophysikalischen Prozesse von pyro-konvektiven Wolken, aufbauend auf einer realistischen Parametrisierung der Aktivierung von Aerosolpartikeln durch die Ergebnisse der Aktivierungsstudie, mit zwei- und dreidimensionalen Simulationen untersucht. Ein modernes zweimomenten mikrophysikalisches Schema wurde in ATHAM implementiert, um den Einfluss der Anzahlkonzentration von Aerosolpartikeln auf die Entwicklung von idealisierten pyro-konvektiven Wolken in US Standardamtosphären für die mittleren Breiten und den Tropen zu untersuchen. Die Ergebnisse zeigen, dass die Anzahlkonzentration der Aerosolpartikel die Bildung von Regen beeinflusst. Für geringe Aerosolkonzentrationen findet die rasche Regenbildung hauptsächlich durch warme mikrophysikalische Prozesse statt. Für höhere Aerosolkonzentrationen ist die Eisphase wichtiger für die Bildung von Regen. Dies führt zu einem verspäteten Einsetzen von Niederschlag für verunreinigtere Atmosphären. Außerdem wird gezeigt, dass die Zusammensetzung der Eisnukleationspartikel (IN) einen starken Einfluss auf die dynamische und mikrophysikalische Struktur solcher Wolken hat. Bei sehr effizienten IN bildet sich Regen früher. Die Untersuchung zum Einfluss des atmosphärischen Hintergrundprofils zeigt eine geringe Auswirkung der Meteorologie auf die Sensitivität der pyro-konvektiven Wolken auf diernAerosolkonzentration. Zum Abschluss wird gezeigt, dass die durch das Feuer emittierte Hitze einen deutlichen Einfluss auf die Entwicklung und die Wolkenobergrenze von pyro-konvektive Wolken hat. Zusammenfassend kann gesagt werden, dass in dieser Dissertation die Mikrophysik von pyrokonvektiven Wolken mit Hilfe von idealisierten Simulation eines Wolkenpaketmodell mit detaillierte spektraler Mikrophysik und eines 3D Modells mit einem zweimomenten Schema im Detail untersucht wurde. Es wird gezeigt, dass die extremen Bedingungen im Bezug auf die vertikale Windgeschwindigkeiten und Aerosolkonzentrationen einen deutlichen Einfluss auf die Entwicklung von pyro-konvektiven Wolken haben.

Measurement and modeling of cloud condensation nuclei in continental air

Atmospheric aerosol particles serving as cloud condensation nuclei (CCN) are key elements of the hydrological cycle and climate. Knowledge of the spatial and temporal distribution of CCN in the atmosphere is essential to understand and describe the effects of aerosols in meteorological models. In this study, CCN properties were measured in polluted and pristine air of different continental regions, and the results were parameterized for efficient prediction of CCN concentrations.The continuous-flow CCN counter used for size-resolved measurements of CCN efficiency spectra (activation curves) was calibrated with ammonium sulfate and sodium chloride aerosols for a wide range of water vapor supersaturations (S=0.068% to 1.27%). A comprehensive uncertainty analysis showed that the instrument calibration depends strongly on the applied particle generation techniques, Köhler model calculations, and water activity parameterizations (relative deviations in S up to 25%). Laboratory experiments and a comparison with other CCN instruments confirmed the high accuracy and precision of the calibration and measurement procedures developed and applied in this study.The mean CCN number concentrations (NCCN,S) observed in polluted mega-city air and biomass burning smoke (Beijing and Pearl River Delta, China) ranged from 1000 cm−3 at S=0.068% to 16 000 cm−3 at S=1.27%, which is about two orders of magnitude higher than in pristine air at remote continental sites (Swiss Alps, Amazonian rainforest). Effective average hygroscopicity parameters, κ, describing the influence of chemical composition on the CCN activity of aerosol particles were derived from the measurement data. They varied in the range of 0.3±0.2, were size-dependent, and could be parameterized as a function of organic and inorganic aerosol mass fraction. At low S (≤0.27%), substantial portions of externally mixed CCN-inactive particles with much lower hygroscopicity were observed in polluted air (fresh soot particles with κ≈0.01). Thus, the aerosol particle mixing state needs to be known for highly accurate predictions of NCCN,S. Nevertheless, the observed CCN number concentrations could be efficiently approximated using measured aerosol particle number size distributions and a simple κ-Köhler model with a single proxy for the effective average particle hygroscopicity. The relative deviations between observations and model predictions were on average less than 20% when a constant average value of κ=0.3 was used in conjunction with variable size distribution data. With a constant average size distribution, however, the deviations increased up to 100% and more. The measurement and model results demonstrate that the aerosol particle number and size are the major predictors for the variability of the CCN concentration in continental boundary layer air, followed by particle composition and hygroscopicity as relatively minor modulators. Depending on the required and applicable level of detail, the measurement results and parameterizations presented in this study can be directly implemented in detailed process models as well as in large-scale atmospheric and climate models for efficient description of the CCN activity of atmospheric aerosols.

Stationary in-situ measurements of aerosols, gaseous pollutants and meteorology : chemical and physical characterization of natural and anthropogenic sources

Natural and anthropogenic emissions of gaseous and particulate matter affect the chemical composition of the atmosphere, impact visibility, air quality, clouds and climate. Concerning climate, a comprehensive characterization of the emergence, composition and transformation of aerosol particles is relevant as their influence on the radiation budget is still rarely understood. Regarding air quality and therefore human health, the formation of atmospheric aerosol particles is of particular importance as freshly formed, small particles penetrate into the human alveolar region and can deposit. Additionally, due to the long residence times of aerosol particles in the atmosphere it is crucial to examine their chemical and physical characteristics.This cumulative dissertation deals with stationary measurements of particles, trace gases and meteorological parameters during the DOMINO (Diel Oxidant Mechanism In relation to Nitrogen Oxide) campaign at the southwest coast of Spain in November/December 2008 and the ship emission campaign on the banks of the Elbe in Freiburg/Elbe in April 2011. Measurements were performed using the Mobile research Laboratory “MoLa” which is equipped with state-of-the-art aerosol particle and trace gas instruments as well as a meteorological station.

Untersuchungen von Aerosolpartikeln und Wolkenresidualpartikeln mittels Einzelpartikel-Massenspektrometrie und optischen Methoden

Atmosphärische Partikel beeinflussen das Klima durch Prozesse wie Streuung, Reflexion und Absorption. Zusätzlich fungiert ein Teil der Aerosolpartikel als Wolkenkondensationskeime (CCN), die sich auf die optischen Eigenschaften sowie die Rückstreukraft der Wolken und folglich den Strahlungshaushalt auswirken. Ob ein Aerosolpartikel Eigenschaften eines Wolkenkondensationskeims aufweist, ist vor allem von der Partikelgröße sowie der chemischen Zusammensetzung abhängig. Daher wurde die Methode der Einzelpartikel-Laserablations-Massenspektrometrie angewandt, die eine größenaufgelöste chemische Analyse von Einzelpartikeln erlaubt und zum Verständnis der ablaufenden multiphasenchemischen Prozesse innerhalb der Wolke beitragen soll.rnIm Rahmen dieser Arbeit wurde zur Charakterisierung von atmosphärischem Aerosol sowie von Wolkenresidualpartikel das Einzelpartikel-Massenspektrometer ALABAMA (Aircraft-based Laser Ablation Aerosol Mass Spectrometer) verwendet. Zusätzlich wurde zur Analyse der Partikelgröße sowie der Anzahlkonzentration ein optischer Partikelzähler betrieben. rnZur Bestimmung einer geeigneten Auswertemethode, die die Einzelpartikelmassenspektren automatisch in Gruppen ähnlich aussehender Spektren sortieren soll, wurden die beiden Algorithmen k-means und fuzzy c-means auf ihrer Richtigkeit überprüft. Es stellte sich heraus, dass beide Algorithmen keine fehlerfreien Ergebnisse lieferten, was u.a. von den Startbedingungen abhängig ist. Der fuzzy c-means lieferte jedoch zuverlässigere Ergebnisse. Darüber hinaus wurden die Massenspektren anhand auftretender charakteristischer chemischer Merkmale (Nitrat, Sulfat, Metalle) analysiert.rnIm Herbst 2010 fand die Feldkampagne HCCT (Hill Cap Cloud Thuringia) im Thüringer Wald statt, bei der die Veränderung von Aerosolpartikeln beim Passieren einer orographischen Wolke sowie ablaufende Prozesse innerhalb der Wolke untersucht wurden. Ein Vergleich der chemischen Zusammensetzung von Hintergrundaerosol und Wolkenresidualpartikeln zeigte, dass die relativen Anteile von Massenspektren der Partikeltypen Ruß und Amine für Wolkenresidualpartikel erhöht waren. Dies lässt sich durch eine gute CCN-Aktivität der intern gemischten Rußpartikel mit Nitrat und Sulfat bzw. auf einen begünstigten Übergang der Aminverbindungen aus der Gas- in die Partikelphase bei hohen relativen Luftfeuchten und tiefen Temperaturen erklären. Darüber hinaus stellte sich heraus, dass bereits mehr als 99% der Partikel des Hintergrundaerosols intern mit Nitrat und/oder Sulfat gemischt waren. Eine detaillierte Analyse des Mischungszustands der Aerosolpartikel zeigte, dass sich sowohl der Nitratgehalt als auch der Sulfatgehalt der Partikel beim Passieren der Wolke erhöhte. rn

Polychlorinated Biphenyls in Glaciers. 2. Model Results of Deposition and Incorporation Processes

In previous work, Alpine glaciers have been identified as a secondary source of persistent organic pollutants (POPs). However, detailed understanding of the processes organic chemicals undergo in a glacial system was missing. Here, we present results from a chemical fate model describing deposition and incorporation of polychlorinated biphenyls (PCBs) into an Alpine glacier (Fiescherhorn, Switzerland) and an Arctic glacier (Lomonosovfonna, Norway). To understand PCB fate and dynamics, we investigate the interaction of deposition, sorption to ice and particles in the atmosphere and within the glacier, revolatilization, diffusion and degradation, and discuss the effects of these processes on the fate of individual PCB congeners. The model is able to reproduce measured absolute concentrations in the two glaciers for most PCB congeners. While the model generally predicts concentration profiles peaking in the 1970s, in the measurements, this behavior can only be seen for higher-chlorinated PCB congeners on Fiescherhorn glacier. We suspect seasonal melt processes are disturbing the concentration profiles of the lower-chlorinated PCB congeners. While a lower-chlorinated PCB congener is mainly deposited by dry deposition and almost completely revolatilized after deposition, a higher-chlorinated PCB congener is predominantly transferred to the glacier surface by wet deposition and then is incorporated into the glacier ice. The incorporated amounts of PCBs are higher on the Alpine glacier than on the Arctic glacier due to the higher precipitation rate and aerosol particle concentration on the former. Future studies should include the effects of seasonal melt processes, calculate the quantities of PCBs incorporated into the entire glacier surface, and estimate the quantity of chemicals released from glaciers to determine the importance of glaciers as a secondary source of organic chemicals to remote aquatic ecosystems.

[Pilot Project: Improved Lung Deposition via a New Nasal Inhalation Procedure].

INTRODUCTION Inhaled drugs can only be effective if they reach the middle and small airways. This study introduces a system that combines a trans-nasal application of aerosols with noninvasive pressure support ventilation. METHODS In a pilot study, 7 COPD patients with GOLD stages II and III inhaled a radiolabeled marker dissolved in water via a trans-nasal route. The mean aerosol particle size was 5.5 µm. Each patient took part in two inhalation sessions that included two application methods and were at least 70 hours apart. During the first session ("passive method"), the patient inhaled the aerosol through an open tube system. The second session ("active method") included pressure support ventilation during the inhalation process. A gamma camera and planar scintigraphy was used to determine the distribution of aerosol particles in the patient's body and lung. RESULTS The pressure supported inhalation ("active method") results in an increased aerosol lung deposition compared to the passive method. Above all, we could demonstrate deposition in the lung periphery with relatively large aerosol particles (5.5 µm). DISCUSSION The results prove that the combination of trans-nasal inhalation with noninvasive pressure support ventilation leads to significantly increased particle deposition in the lung.

Impacts on particles and ozone by transport processes recorded at urban and high-altitude monitoring stations

In order to evaluate the influence of particle transport episodes on particle number concentration temporal trends at both urban and high-altitude (Aitana peak-1558 m a.s.l.) stations, a simultaneous sampling campaign from October 2011 to September 2012 was performed. The monitoring stations are located in southeastern Spain, close to the Mediterranean coast. The annual average value of particle concentration obtained in the larger accumulation mode (size range 0.25–1 μm) at the mountain site, 55.0 ± 3.0 cm− 3, was practically half that of the value obtained at the urban station (112.0 ± 4.0 cm− 3). The largest difference between both stations was recorded during December 2011 and January 2012, when particles at the mountain station registered the lowest values. It was observed that during urban stagnant episodes, particle transport from urban sites to the mountain station could take place under specific atmospheric conditions. During these transports, the major particle transfer is produced in the 0.5–2 μm size range. The minimum difference between stations was recorded in summer, particularly in July 2012, which is most likely due to several particle transport events that affected only the mountain station. The particle concentration in the coarse mode was very similar at both monitoring sites, with the biggest difference being recorded during the summer months, 0.4 ± 0.1 cm− 3 at the urban site and 0.9 ± 0.1 cm− 3 at the Aitana peak in August 2012. Saharan dust outbreaks were the main factor responsible for these values during summer time. The regional station was affected more by these outbreaks, recording values of > 4.0 cm− 3, than the urban site. This long-range particle transport from the Sahara desert also had an effect upon O3 levels measured at the mountain station. During periods affected by Saharan dust outbreaks, ozone levels underwent a significant decrease (3–17%) with respect to its mean value.

Development of a novel in vitro system for nasal drug delivery development

There is currently, no ideal system for studying nasal drug delivery in vitro. The existing techniques such as the Ussing chamber and cell culture all have major disadvantages. Most importantly, none of the existing techniques accurately represent the interior of the nasal cavity, with its airflow and humidity; neither do they allow the investigation of solid dosage forms.The work in this thesis represents the development of an in vitro model system in which the interior characteristics of the nasal cavity are closely represented, and solid or minimal volume dosage forms can be investigated. The complete nasal chamber consists of two sections: a lower tissue, viability chamber and an upper nasal chamber. The lower tissue viability chamber has been shown, using existing tissue viability monitoring techniques, to maintain the viability of a number of epithelial tissues, including porcine and rabbit nasal tissue, and rat ileal and Payers' patch tissue. The complete chamber including the upper nasal chamber has been shown to provide tissue viability for porcine and rabbit nasal tissue above that available using the existing Ussing chamber techniques. Adaptation of the complete system, and the development of the necessary experimental protocols that allow aerosol particle-sizing, together with videography, has shown that the new factors investigated, humidity and airflow, have a measurable effect on the delivered dose from a typical nasal pump. Similarly, adaptation of the chamber to fit under a confocal microscope, and the development of the necessary protocols has shown the effect of surface and size on the penetration of microparticulate materials into nasal epithelial tissues. The system developed in this thesis has been shown to be flexible, in allowing the development of the confocal and particle-sizing systems. For future nasal drug delivery studies, the ability to measure such factors as the size of the delivered system in the nasal cavity, the depth of penetration of the formulation into the tissue are essential. Additionally, to have access to other data such as that obtained from drug transport in the same system, and to have the tissue available for histological examination represents a significant advance in the usefulness of such an in vitro technique for nasal delivery.

EUSAAR size distribution analysis database

Two years of harmonized aerosol number size distribution data from 24 European field monitoring sites have been analysed. The results give a comprehensive overview of the European near surface aerosol particle number concentrations and number size distributions between 30 and 500 nm of dry particle diameter. Spatial and temporal distribution of aerosols in the particle sizes most important for climate applications are presented. We also analyse the annual, weekly and diurnal cycles of the aerosol number concentrations, provide log-normal fitting parameters for median number size distributions, and give guidance notes for data users. Emphasis is placed on the usability of results within the aerosol modelling community. We also show that the aerosol number concentrations of Aitken and accumulation mode particles (with 100 nm dry diameter as a cut-off between modes) are related, although there is significant variation in the ratios of the modal number concentrations. Different aerosol and station types are distinguished from this data and this methodology has potential for further categorization of stations aerosol number size distribution types. The European submicron aerosol was divided into characteristic types: Central European aerosol, characterized by single mode median size distributions, unimodal number concentration histograms and low variability in CCN-sized aerosol number concentrations; Nordic aerosol with low number concentrations, although showing pronounced seasonal variation of especially Aitken mode particles; Mountain sites (altitude over 1000 m a.s.l.) with a strong seasonal cycle in aerosol number concentrations, high variability, and very low median number concentrations. Southern and Western European regions had fewer stations, which decreases the regional coverage of these results. Aerosol number concentrations over the Britain and Ireland had very high variance and there are indications of mixed air masses from several source regions; the Mediterranean aerosol exhibit high seasonality, and a strong accumulation mode in the summer. The greatest concentrations were observed at the Ispra station in Northern Italy with high accumulation mode number concentrations in the winter. The aerosol number concentrations at the Arctic station Zeppelin in Ny-Ålesund in Svalbard have also a strong seasonal cycle, with greater concentrations of accumulation mode particles in winter, and dominating summer Aitken mode indicating more recently formed particles. Observed particles did not show any statistically significant regional work-week or weekday related variation in number concentrations studied. Analysis products are made for open-access to the research community, available in a freely accessible internet site. The results give to the modelling community a reliable, easy-to-use and freely available comparison dataset of aerosol size distributions.

Coupling an aerosol box model with one-dimensional flow: a tool for understanding observations of new particle formation events

Field observations of new particle formation and the subsequent particle growth are typically only possible at a fixed measurement location, and hence do not follow the temporal evolution of an air parcel in a Lagrangian sense. Standard analysis for determining formation and growth rates requires that the time-dependent formation rate and growth rate of the particles are spatially invariant; air parcel advection means that the observed temporal evolution of the particle size distribution at a fixed measurement location may not represent the true evolution if there are spatial variations in the formation and growth rates. Here we present a zero-dimensional aerosol box model coupled with one-dimensional atmospheric flow to describe the impact of advection on the evolution of simulated new particle formation events. Wind speed, particle formation rates and growth rates are input parameters that can vary as a function of time and location, using wind speed to connect location to time. The output simulates measurements at a fixed location; formation and growth rates of the particle mode can then be calculated from the simulated observations at a stationary point for different scenarios and be compared with the ‘true’ input parameters. Hence, we can investigate how spatial variations in the formation and growth rates of new particles would appear in observations of particle number size distributions at a fixed measurement site. We show that the particle size distribution and growth rate at a fixed location is dependent on the formation and growth parameters upwind, even if local conditions do not vary. We also show that different input parameters used may result in very similar simulated measurements. Erroneous interpretation of observations in terms of particle formation and growth rates, and the time span and areal extent of new particle formation, is possible if the spatial effects are not accounted for.

Quantitative determination of carbonaceous particle mixing state in Paris using single-particle mass spectrometer and aerosol mass spectrometer measurements

Single-particle mixing state information can be a powerful tool for assessing the relative impact of local and regional sources of ambient particulate matter in urban environments. However, quantitative mixing state data are challenging to obtain using single-particle mass spectrometers. In this study, the quantitative chemical composition of carbonaceous single particles has been determined using an aerosol time-of-flight mass spectrometer (ATOFMS) as part of the MEGAPOLI 2010 winter campaign in Paris, France. Relative peak areas of marker ions for elemental carbon (EC), organic aerosol (OA), ammonium, nitrate, sulfate and potassium were compared with concurrent measurements from an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), a thermal-optical OCEC analyser and a particle into liquid sampler coupled with ion chromatography (PILS-IC). ATOFMS-derived estimated mass concentrations reproduced the variability of these species well (R-2 = 0.67-0.78), and 10 discrete mixing states for carbonaceous particles were identified and quantified. The chemical mixing state of HR-ToF-AMS organic aerosol factors, resolved using positive matrix factorisation, was also investigated through comparison with the ATOFMS dataset. The results indicate that hydrocarbon-like OA (HOA) detected in Paris is associated with two EC-rich mixing states which differ in their relative sulfate content, while fresh biomass burning OA (BBOA) is associated with two mixing states which differ significantly in their OA/EC ratios. Aged biomass burning OA (OOA(2)-BBOA) was found to be significantly internally mixed with nitrate, while secondary, oxidised OA (OOA) was associated with five particle mixing states, each exhibiting different relative secondary inorganic ion content. Externally mixed secondary organic aerosol was not observed. These findings demonstrate the range of primary and secondary organic aerosol mixing states in Paris. Examination of the temporal behaviour and chemical composition of the ATOFMS classes also enabled estimation of the relative contribution of transported emissions of each chemical species and total particle mass in the size range investigated. Only 22% of the total ATOFMS-derived particle mass was apportioned to fresh, local emissions, with 78% apportioned to regional/continental-scale emissions. Single-particle mixing state information can be a powerful tool for assessing the relative impact of local and regional sources of ambient particulate matter in urban environments. However, quantitative mixing state data are challenging to obtain using single-particle mass spectrometers. In this study, the quantitative chemical composition of carbonaceous single particles has been determined using an aerosol time-of-flight mass spectrometer (ATOFMS) as part of the MEGAPOLI 2010 winter campaign in Paris, France. Relative peak areas of marker ions for elemental carbon (EC), organic aerosol (OA), ammonium, nitrate, sulfate and potassium were compared with concurrent measurements from an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), a thermal-optical OCEC analyser and a particle into liquid sampler coupled with ion chromatography (PILS-IC). ATOFMS-derived estimated mass concentrations reproduced the variability of these species well (R-2 = 0.67-0.78), and 10 discrete mixing states for carbonaceous particles were identified and quantified. The chemical mixing state of HR-ToF-AMS organic aerosol factors, resolved using positive matrix factorisation, was also investigated through comparison with the ATOFMS dataset. The results indicate that hydrocarbon-like OA (HOA) detected in Paris is associated with two EC-rich mixing states which differ in their relative sulfate content, while fresh biomass burning OA (BBOA) is associated with two mixing states which differ significantly in their OA/EC ratios. Aged biomass burning OA (OOA(2)-BBOA) was found to be significantly internally mixed with nitrate, while secondary, oxidised OA (OOA) was associated with five particle mixing states, each exhibiting different relative secondary inorganic ion content. Externally mixed secondary organic aerosol was not observed. These findings demonstrate the range of primary and secondary organic aerosol mixing states in Paris. Examination of the temporal behaviour and chemical composition of the ATOFMS classes also enabled estimation of the relative contribution of transported emissions of each chemical species and total particle mass in the size range investigated. Only 22% of the total ATOFMS-derived particle mass was apportioned to fresh, local emissions, with 78% apportioned to regional/continental-scale emissions.

Single particle characterization using the soot particle aerosol mass spectrometer (SP-AMS)

Understanding the impact of atmospheric black carbon (BC) containing particles on human health and radiative forcing requires knowledge of the mixing state of BC, including the characteristics of the materials with which it is internally mixed. In this study, we demonstrate for the first time the capabilities of the Aerodyne Soot-Particle Aerosol Mass Spectrometer equipped with a light scattering module (LS-SP-AMS) to examine the mixing state of refractory BC (rBC) and other aerosol components in an urban environment (downtown Toronto). K-means clustering analysis was used to classify single particle mass spectra into chemically distinct groups. One resultant cluster is dominated by rBC mass spectral signals (C+1 to C+5) while the organic signals fall into a few major clusters, identified as hydrocarbon-like organic aerosol (HOA), oxygenated organic aerosol (OOA), and cooking emission organic aerosol (COA). A nearly external mixing is observed with small BC particles only thinly coated by HOA ( 28% by mass on average), while over 90% of the HOA-rich particles did not contain detectable amounts of rBC. Most of the particles classified into other inorganic and organic clusters were not significantly associated with BC. The single particle results also suggest that HOA and COA emitted from anthropogenic sources were likely major contributors to organic-rich particles with low to mid-range aerodynamic diameter (dva). The similar temporal profiles and mass spectral features of the organic clusters and the factors from a positive matrix factorization (PMF) analysis of the ensemble aerosol dataset validate the conventional interpretation of the PMF results.