Microstructure modeling and prediction of the mechanical properties of advanced high strength steels

Dual phase (DP) steels were modeled using 2D and 3D representative volume elements (RVE). Both the 2D and 3D models were generated using the Monte-Carlo-Potts method to represent the realistic microstructural details. In the 2D model, a balance between computational efficiency and required accuracy in truly representing heterogeneous microstructure was achieved. In the 3D model, a stochastic template was used to generate a model with high spatial fidelity. The 2D model proved to be efficient for characterization of the mechanical properties of a DP steel where the effect of phase distribution, morphology and strain partitioning was studied. In contrast, the current 3D modeling technique was inefficient and impractical due to significant time cost. It is shown that the newly proposed 2D model generation technique is versatile and sufficiently accurate to capture mechanical properties of steels with heterogeneous microstructure.

Properties and automotive applications of advanced high-strength steels (AHSS)

Advanced high-strength steels (AHSS) are a class of steel used primarily in sheet form for automotive structures. The microstructures of the types of steel in this classification were initially multiphase, with ferrite as the dominant phase; however, grades introduced more recently have been fully martensitic or based on austenite. This chapter initially introduces the requirements of an automotive body structure, then the different classes of AHSS that have been used in the automotive industry and their typical characteristic tensile properties. The specific properties that are required for steel used in automotive body structures are subsequently described, including formability and crash behaviour. Finally, some of the current and future trends in the development of new steel grades are discussed.

Phase transformations in maraging steels

Research on the kinetics of precipitate formation and austenite reversion in maraging steels has received great attention due to their importance to steel properties. Judging from the literature in recent years, research into maraging steels has been very active, mainly extending to new types of steels, for new applications beyond the traditional strength requirements. This chapter provides an in-depth overview of the literature in this area. In addition, the kinetics of precipitate formation are analysed using the Johnson–Mehl–Avrami (JMA) theory.

Precipitate characterisation of an advanced high-strength low-alloy (HSLA) steel using atom probe tomography

Increased fuel economy, combined with the need for the improved safety has generated the development of new hot-rolled high-strength low-alloy (HSLA) and multiphase steels such as dual-phase or transformation-induced plasticity steels with improved ductility without sacrificing strength and crash resistance. However, the modern multiphase steels with good strength-ductility balance showed deteriorated stretch-flangeability due to the stress concentration region between the soft ferrite and hard martensite phases [1]. Ferritic, hot-rolled steels can provide good local elongation and, in turn, good stretch-flangeability [2]. However, conventional HSLA ferritic steels only have a tensile strength of not, vert, similar600 MPa, while steels for the automotive industry are now required to have a high tensile strength of not, vert, similar780 MPa, with excellent elongation and stretch-flangeability [1]. This level of strength and stretch-flangeability can only be achieved by precipitation hardening of the ferrite matrix with very fine precipitates and by ferrite grain refinement. It has been suggested that Mo [3] and Ti [4] should be added to form carbides and decrease the coiling temperature to 650 °C since only a low precipitation temperature can provide the precipitation refinement [4]. These particles appeared to be (Ti, Mo)C, with a cubic lattice and a parameter of 0.433 nm, and they were aligned in rows [4]. It was reported [4] that the formation of these very fine carbides led to an increase in strength of not, vert, similar300 MPa. However, the detailed analysis of these particles has not been performed to date due to their nanoscale size. The aim of this work was to carry out a detailed investigation using atom probe tomography (APT) of precipitates formed in hot-rolled low-carbon steel containing additions Ti and Mo.

The investigated low-carbon steel, containing Fe–0.1C–1.24Mn–0.03Si–0.11Cr–0.11Mo–0.09Ti–0.091Al at.%, was produced by hot rolling. The processing route has been described in detail elsewhere [5] European Patent Application, 1616970 A1, 18.01.2006.[5]. The microstructure was characterised by transmission electron microscopy (TEM) on a Philips CM 20, operated at 200 kV using thin foil and carbon replica techniques. Qualitative energy dispersive X-ray spectroscopy (EDXS) was used to analyse the chemical composition of particles. The atomic level of particle characterisation was performed at the University of Sydney using a local electrode atom probe [6]. APT was carried out using a pulse repetition rate of 200 kHz and a 20% pulse fraction on the sample with temperature of 80 K. The extent of solute-enriched regions (radius of gyration) and the local solute concentrations in these regions were estimated using the maximum separation envelope method with a grid spacing of 0.1 nm [7]. A maximum separation distance between the atoms of interest of dmax = 1 nm was used.

The microstructure of the steel consisted of two types of fine ferrite grains: (i) small recrystallised grains with an average grain size of 1.4 ± 0.2 μm; and (ii) grains with a high dislocation density (5.8 ± 1.4 × 1014 m−2) and an average grain size of 1.9 ± 0.1 μm in thickness and 2.7 ± 0.1 μm in length (Fig. 1a). Some grains with high dislocation density displayed an elongated shape with Widmanstätten side plates and also the formation of cells and subgrains (Fig. 1a). The volume fraction of recrystallised grains was 34 ± 8%.

Characterization of nano-scale particles in hot-rolled, high strength low alloy steels (HSLA)

The contribution of nano-scale particles observed using Atom Probe Tomography in an increase of yield strength of conventional and advanced HSLA steels was studied. The advanced HSLA steel showed higher yield strength than conventional HSLA steel. There were two types of carbides, which primarily contribute to an increase in yield strength of conventional HSLA steel: (i) coarse TiC with average size of 25±5nm and (ii) fine TiC with average radius of 3±1.2nm. The presence of two types of carbides was found in the microstructure of advanced HSLA steel: (i)
nano-scale Ti0.98Mo0.02C0.6 carbides with average radius of 2.2±0.5nm, and (ii) C19Cr7Mo24 particles with an average radius of 1.5±0.3nm. The contribution of precipitation hardening in the yield strength of advanced HSLA steel due to the nano-scale particles was 174MPa, while this value in the conventional HSLA steel was 128MPa.

Atom probe tomography as a tool to advance steels design and performance

Development of modern steels consisting of complex or nano-scale microstructures with advanced properties requires in-depth understanding of the mechanisms responsible for their microstructure/property relationships. The evolution of microstructure during processing is often associated with various changes taking place at atomic level. These include solute distribution between phases as a result of phase transformations, formation of atmospheres at dislocations, clustering and precipitation phenomena due to various thermo-mechanical processing schedules and/or heat treatments. Atom probe tomography (APT) is invaluable tool for gaining insight into events at atomic scale determining the steel properties. This technique also contributes to the fundamental understanding of phase transformations, which is essential for nano-scale engineering of modern steels and optimization of their performance. In this work application of APT to study solute segregation, clustering and precipitation in TRIP steels and nanostructured bainitic steels after isothermal heat-treatment and after thermomechanical processing will be discussed.

Springback data from stamping and simulating the forming of advanced high strength steel

This dataset is comprised of a spreadsheet of simulation result files, cross-section geometries of stamped parts, strain results of cross-section of stamped parts, simulation data (strain stress displacement energies), and variation data of material properties of a single coil. This data is a collection of both experimental and simulation results from industrial and laboratory stamping of advanced high strength steels (AHSS). The steels that were stamped were a typical high-strength low-alloy (HSLA) steel, a transformation-induced plasticity (TRIP) steel, a super HSLA steel, and a dual phase (DP) steel. The selected part was an automatic Ford Falcon front cross-member component using the Ford Geelong stamping plant. The variation of the material and stamped parts was also collected.

Effect of tensile pre-strain on bending and unloading of automotive steels

In recent years, advanced high strength steels (AHSS) have been used in a wide range of automotive applications; they may have property variations through the thickness and the properties may also be dependent of prior processing including pre-straining. In order to model forming processes precisely using, for example, finite element analysis, it is important that material input data should adequately reflect these effects. It is known that shape defects in roll forming are related to small strains in material that has undergone prior deformation in a different strain path. Much research has already been performed on the change in the Young’s Modulus once a steel sheet has been plastically deformed,however many of these tests have only been conducted using tensile testing, and therefore may not take into account differences in compressive and tensile unloading. This research investigates the effect of tensile pre-straining on bending behaviour for various types of material;in bending, one half of the sheet will load and unload in compression and hence experience deformation under a reversed stress. Four different materials were pre-strained in tension with 1%, 3%, 7%, 11% and 25% elongation. Using a free bending test, moment curvature diagrams were obtained for bending and unloading. The results showed that the characteristics of the moment curvature diagram depended on the degree of pre-straining; more highly strained samples showed an earlier elastic-plastic transformation and a decreased Young's Modulus during unloading. This was compared to previous literature results using only tensile tests. Our results could influence the modeling of springback in low tension sheet operations, such as roll forming.