Fixed bed reactor performance of invertase immobilized on montmorillonite

Invertase was immobilized on acid activated montmorillonite via two independent procedures, adsorption and covalent binding. The immobilized enzymes were characterized by XRD, NMR and N2 adsorption measurements and their activity was tested in a fixed bed reactor. XRD revealed that the enzyme was situated on the periphery of the clay and the side chains of different amino acid residues were involved in intercalation with the clay matrix. NMR demonstrated that tetrahedral Al was linked to the enzyme during adsorption and the octahedral Al was involved during covalent binding. Secondary interaction of the enzyme with Al was also observed. N2 adsorption studies showed that covalent binding of enzymes caused pore blockage since the highly polymeric species were located at the pore entrance. The fixed bed reactor proved to be efficient for the immobilized invertase. The optimum pH and pH stability improved upon immobilization. The kinetic parameters calculated also showed an enhanced efficiency of the immobilized systems. They could be used continuously for long period. Covalently bound invertase demonstrated greater operational stability.

Liquid phase benzoylation of arenes over iron promoted sulphated zirconia

The present work undertakes the preparation and physico-chemical characterisation of iron promoted sulphated zirconia (SZ) with different amounts of iron loading and their application to Friedel-Crafts benzoylation of benzene, toluene and xylene under different experimental conditions, XRD and laser Raman techniques reveal the stabilisation of the tetragonal phase of zirconia and the existence of iron in highly dispersed form as Fe203 on the catalyst surface. The surface acidic properties were determined by ammonia temperature programmed desorption (TPD) and perylene adsorption, The results were supported by the TGA studies after adsorption of pyridine and 2,6-dimethylpyridine (2,6-DMP), Strong Lewis acid sites on the surface, which are evident from TPD and perylene adsorption studies. explain the high catalytic activity of the systems towards benzoylation. The experimental results provide evidence for the truly heterogeneous nature of the reaction. The studies also establish the resistance to deactivation in the metal incorporated sulphated systems.

Influence of sulphate content on the physico-chemical properties and catalytic activity of some sulphated zirconia systems

The present work attempts a systematic examination of the effect of sulphate content on the physico-chemical properties and catalytic activity of sulphated zirconia and iron promoted sulphated zirconia systems. Sulphate content is estimated by EDX analysis. The amount of sulphate incorporated has been found to influence the surface area, crystal structure and the acid strength distribution. Ammonia TPD and adsorption studies using perylene have enabled the determination of surface acidic properties. The results are supported by the thermodesorption studies using pyridine and 2,6-dimethylpyridine. The catalytic activity towards benzoylation reaction has been correlated with the surface acidity of the systems.

Differential induction, isolation, physicochemical and molecular characterization of temperate phages of environmental Vibrio cholerae as evidence of phage mediated Horizontal Gene Transfer

The resurgence of the enteric pathogen Vibrio cholerae, the causative organism of epidemic cholera, remains a major health problem in many developing countries like India. The southern Indian state of Kerala is endemic to cholera. The outbreaks of cholera follow a seasonal pattern in regions of endemicity. Marine aquaculture settings and mangrove environments of Kerala serve as reservoirs for V. cholerae. The non-O1/non-O139 environmental isolates of V. cholerae with incomplete ‘virulence casette’ are to be dealt with caution as they constitute a major reservoir of diverse virulence genes in the marine environment and play a crucial role in pathogenicity and horizontal gene transfer. The genes coding cholera toxin are borne on, and can be infectiously transmitted by CTXΦ, a filamentous lysogenic vibriophages. Temperate phages can provide crucial virulence and fitness factors affecting cell metabolism, bacterial adhesion, colonization, immunity, antibiotic resistance and serum resistance. The present study was an attempt to screen the marine environments like aquafarms and mangroves of coastal areas of Alappuzha and Cochin, Kerala for the presence of lysogenic V. cholerae, to study their pathogenicity and also gene transfer potential. Phenotypic and molecular methods were used for identification of isolates as V. cholerae. The thirty one isolates which were Gram negative, oxidase positive, fermentative, with or without gas production on MOF media and which showed yellow coloured colonies on TCBS (Thiosulfate Citrate Bile salt Sucrose) agar were segregated as vibrios. Twenty two environmental V. cholerae strains of both O1 and non- O1/non-O139 serogroups on induction with mitomycin C showed the presence of lysogenic phages. They produced characteristic turbid plaques in double agar overlay assay using the indicator strain V. cholerae El Tor MAK 757. PCR based molecular typing with primers targeting specific conserved sequences in the bacterial genome, demonstrated genetic diversity among these lysogen containing non-O1 V. cholerae . Polymerase chain reaction was also employed as a rapid screening method to verify the presence of 9 virulence genes namely, ctxA, ctxB, ace, hlyA, toxR, zot,tcpA, ninT and nanH, using gene specific primers. The presence of tcpA gene in ALPVC3 was alarming, as it indicates the possibility of an epidemic by accepting the cholera. Differential induction studies used ΦALPVC3, ΦALPVC11, ΦALPVC12 and ΦEKM14, underlining the possibility of prophage induction in natural ecosystems, due to abiotic factors like antibiotics, pollutants, temperature and UV. The efficiency of induction of prophages varied considerably in response to the different induction agents. The growth curve of lysogenic V. cholerae used in the study drastically varied in the presence of strong prophage inducers like antibiotics and UV. Bacterial cell lysis was directly proportional to increase in phage number due to induction. Morphological characterization of vibriophages by Transmission Electron Microscopy revealed hexagonal heads for all the four phages. Vibriophage ΦALPVC3 exhibited isometric and contractile tails characteristic of family Myoviridae, while phages ΦALPVC11 and ΦALPVC12 demonstrated the typical hexagonal head and non-contractile tail of family Siphoviridae. ΦEKM14, the podophage was distinguished by short non-contractile tail and icosahedral head. This work demonstrated that environmental parameters can influence the viability and cell adsorption rates of V. cholerae phages. Adsorption studies showed 100% adsorption of ΦALPVC3 ΦALPVC11, ΦALPVC12 and ΦEKM14 after 25, 30, 40 and 35 minutes respectively. Exposure to high temperatures ranging from 50ºC to 100ºC drastically reduced phage viability. The optimum concentration of NaCl required for survival of vibriophages except ΦEKM14 was 0.5 M and that for ΦEKM14 was 1M NaCl. Survival of phage particles was maximum at pH 7-8. V. cholerae is assumed to have existed long before their human host and so the pathogenic clones may have evolved from aquatic forms which later colonized the human intestine by progressive acquisition of genes. This is supported by the fact that the vast majority of V. cholerae strains are still part of the natural aquatic environment. CTXΦ has played a critical role in the evolution of the pathogenicity of V. cholerae as it can transmit the ctxAB gene. The unusual transformation of V. cholerae strains associated with epidemics and the emergence of V. cholera O139 demonstrates the evolutionary success of the organism in attaining greater fitness. Genetic changes in pathogenic V. cholerae constitute a natural process for developing immunity within an endemically infected population. The alternative hosts and lysogenic environmental V. cholerae strains may potentially act as cofactors in promoting cholera phage ‘‘blooms’’ within aquatic environments, thereby influencing transmission of phage sensitive, pathogenic V. cholerae strains by aquatic vehicles. Differential induction of the phages is a clear indication of the impact of environmental pollution and global changes on phage induction. The development of molecular biology techniques offered an accessible gateway for investigating the molecular events leading to genetic diversity in the marine environment. Using nucleic acids as targets, the methods of fingerprinting like ERIC PCR and BOX PCR, revealed that the marine environment harbours potentially pathogenic group of bacteria with genetic diversity. The distribution of virulence associated genes in the environmental isolates of V. cholerae provides tangible material for further investigation. Nucleotide and protein sequence analysis alongwith protein structure prediction aids in better understanding of the variation inalleles of same gene in different ecological niche and its impact on the protein structure for attaining greater fitness of pathogens. The evidences of the co-evolution of virulence genes in toxigenic V. cholerae O1 from different lineages of environmental non-O1 strains is alarming. Transduction studies would indicate that the phenomenon of acquisition of these virulence genes by lateral gene transfer, although rare, is not quite uncommon amongst non-O1/non-O139 V. cholerae and it has a key role in diversification. All these considerations justify the need for an integrated approach towards the development of an effective surveillance system to monitor evolution of V. cholerae strains with epidemic potential. Results presented in this study, if considered together with the mechanism proposed as above, would strongly suggest that the bacteriophage also intervenes as a variable in shaping the cholera bacterium, which cannot be ignored and hinting at imminent future epidemics.

Avaliação da capacidade de adsorção do CO2 em zeólita 12X com gases sintéticos e originados da pirólise do lodo de esgoto

This work depicts a study of the adsorption of carbon dioxide on zeolite 13X. The activities were divided into four stages: study batch adsorption capacity of the adsorbent with synthetic CO2 (4%), fixed bed dynamic evaluation with the commercial mixture of gases (4% CO2, 1.11% CO, 1 2% H2, 0.233% CH4, 0.1% C3, 0.0233% C4 argon as inert closing balance), fixed bed dynamic modeling and evaluation of the breakthrough curve of CO2 originated from the pyrolysis of sewage sludge. The sewage sludge and the adsorbent were characterized by analysis TG / DTA, SEM, XRF and BET. Adsorption studies were carried out under the following operating conditions: temperature 40 °C (for the pyrolysis of the sludge T = 600 °C), pressures of 0.55 to 5.05 bar (batch process), flow rate of the gaseous mixture between 50 - 72 ml/min and the adsorbent masses of 10, 15 and 20 g (fixed bed process). The time for the adsorption batch was 7 h and on the fixed bed was around 180 min. The results of this study showed that in batch adsorption process step with zeolite 13X is efficient and the mass of adsorbed CO2 increases with the increases pressure, decreases with temperature increases and rises due the increase of activation temperature adsorbent. In the batch process were evaluated the breakthrough curves, which were compared with adsorption isotherms represented by the models of Langmuir, Freündlich and Toth. All models well adjusted to the experimental points, but the Langmuir model was chosen in view of its use in the dynamic model does not have implications for adsorption (indeterminacy and larger number of parameters such as occurred with others) in solving the equation. In the fixed bed dynamic study with the synthetic gas mixture, 20 g of mass adsorbent showed the maximum adsorption percentage 46.7% at 40 °C temperature and 50 mL/min of flow rate. The model was satisfactorily fitted to the three breakthrough curves and the parameters were: axial dispersion coefficient (0.0165 dm2/min), effective diffusivity inside the particle (dm2/min 0.0884) and external transfer coefficient mass (0.45 dm/min). The breakthrough curve for CO2 in the process of pyrolysis of the sludge showed a fast saturation with traces of aerosols presents in the gas phase into the fixed bed under the reaction process

Microemulsões aplicadas ao tratamento de Óleos isolantes

Naphthenic lubricating oils are used in transformers with the purpose of promoting electrical insulation and dissipating heat. The working temperature range of these oils typically lies between 60°C and 90°C and their useful life is 40 years in average. In that temperature range, the oils are decomposed during operation, whereby a small fraction of polar compounds are formed. The presence of these compounds may induce failure and loss of physical, chemical and electrical properties of the oil, thus impairing the transformer operation. By removing these contaminants, one allows the oxidized insulating oil to be reused without damaging the equipment. In view of this, an investigation on the use of surfactants and microemulsions as extracting agents, and modified diatomite as adsorbent, has been proprosed in this work aiming to remove polar substances detected in oxidized transformer oils. The extraction was carried out by a simple-contact technique at room temperature. The system under examination was stirred for about 10 minutes, after which it was allowed to settle at 25°C until complete phase separation. In another experimental approach, adsorption equilibrium data were obtained by using a batch system operating at temperatures of 60, 80 and 100°C. Analytical techniques involving determination of the Total Acidity Number (TAN) and infrared spectrophotometry have been employed when monitoring the decomposition and recovery processes of the oils. The acquired results indicated that the microemulsion extraction system comprising Triton® X114 as surfactant proved to be more effective in removing polar compounds, with a decrease in TAN index from 0.19 to 0.01 mg KOH/g, which is consistent with the limits established for new transformer oils (maximal TAN = 0.03 mg KOH/g). In the adsorption studies, the best adsorption capacity values were as high as 0.1606 meq.g/g during conventional adsoprtion procedures using natural bauxite, and as high as 0.016 meq.g/g for the system diatomite/Tensiofix® 8426. Comparatively in this case, a negative effect could be observed on the adsorption phenomenon due to microemulsion impregnation on the surface of the diatomite

Recuperação e purificação de ramnolipídeos produzidos por pseudomonas aeruginosa P029-GVIIA utilizando melaço de cana como substrato

Biosurfactants are molecules produced by microorganisms mainly bacteria as Pseudomonas and Bacillus. Among the biosurfactants, rhamnolipids play an important role due to their tensoactive as well as emulsifying properties. Besides can be produced in a well consolidated way the production costs of biosurfactants are quite expansive mainly if downstream processing is goning to be considered. Actually, attention has been given to identification of biosurfactants as well as optimization of its fermentative processes including downstream ones. This work deals with the development of strategies to recovery and purification of rhamnolipids produced by Pseudomonas aeruginosa P029-GVIIA using sugar-cane molasses as substrate. Broth free of cells was used in order to investigate the best strategies to recovery and purification produced by this system. Between the studied acids (HCl and H2SO4) for the acid precipitation step, HCl was the best one as has been showed by the experimental design 24. Extraction has been carried out using petroleum ether and quantification has been done using the thioglycolic acid method. Adsorption studies were carried out with activated carbon in a batch mode using a 24 experimental design as well as combined with an hydrophobic resin Streamline Phenyl aiming to separate the produced biosurfactant. Biosurfactant partial identification was carried out using High Performance Liquid Chromatography (HPLC). Experiments in batch mode showed that adsorption has been controlled mainly by pH and temperature. It was observed a reduction of 41.4% for the liquid phase and the solid phase it was possible to adsorb up to 15 mg of rhamnolipd/g of activated carbon. The kinetics of adsorption has been well fitted to a pseudo-first order reaction with velocity constant (k1) of 1.93 x 10-2 min-1. Experiments in packed bed ranging concentration on eluent (acetone) has been shown the highest recovery factor of 98% when pure acetone has been used. The combined effect if using activated carbon with an hydrophobic resin Streamline Phenyl has been shown successful for the rhamnolipids purification. It has been possible to purify a fraction of the crude broth with 98% of purity when the eluted of activated carbon packed bed was used with pure acetone

Estudo da eficácia do tensoativo sorbitano tween 80 veiculado em nanoemulsão contendo óleo de soja, como inibidor de corrosão

Nowadays, the use of chemicals that satisfactorily meet the needs of different sectors of the chemical industry is linked to the consumption of biodegradable materials. In this context, this work contemplated biotechnological aspects with the objective of developing a more environmentally-friendly corrosion inhibitor. In order to achieve this goal, nanoemulsion-type systems (NE) were obtained by varying the amount of Tween 80 (9 to 85 ppm) a sortitan surfactant named polyoxyethylene (20) monooleate. This NE-system was analyzed using phase diagrams in which the percentage of the oil phase (commercial soybean oil, codenamed as OS) was kept constant. By changing the amount of Tween 80, several polar NE-OS derived systems (O/W-type nanoemulsion) were obtained and characterized through light scattering, conductivity and pH, and further subjected to electrochemical studies. The interfacial behavior of these NE-OS derived systems (codenamed NE-OS1, S2, S3, S4 and S5) as corrosion inhibitors on carbon steel AISI 1020 in saline media (NaCl 3.5%) were evaluated by measurement of Open Circuit Potential (OCP), Polarization Curves (Tafel extrapolation method) and Electrochemical Impedance Spectroscopy (EIS). The analyzed NE-OS1 and NE-OS2 systems were found to be mixed inhibitors with quantitative efficacy (98.6% - 99.7%) for concentrations of Tween 80 ranging between 9 and 85 ppm. According to the EIS technique, maximum corrosion efficiency was observed for some tested NE-OS samples. Additionaly to the electrochemical studies, Analysis of Variance (ANOVA) and Principal Component Analysis (PCA) were used, characterization of the nanoemulsion tested systems and adsorption studies, respectively, which confirmed the results observed in the experimental analyses using diluted NE-OS samples in lower concentrations of Tween 80 (0.5 1.75 ppm)

Hidrogeneoftalato de potássio como molécula modelo para estudos de adsorção sobre TiO2

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudos de adsorção do ácido clavulânico

Pós-graduação em Biotecnologia - IQ

Síntese e caracterização de nanopartículas de ZrO2 por rota hidrotérmica

Pós-graduação em Ciência e Tecnologia de Materiais - FC

Síntese e caracterização de materiais híbridos (PCHs e Organoargilas) com aplicabilidade na adsorção de fenol, benzeno e tolueno

Este estudo avalia o uso de argila do Estado do Acre de natureza esmectítica (argila original) como precursora na síntese de PCHs (Porous Clay Heterostructure) e na organofuncionalização com mercaptopropiltrimetoxisilano (MPTS-Arg) e aplicabilidade desses materiais como adsorventes de fenol, benzeno e tolueno em fase líquida. A síntese de PCHs envolve as seguintes etapas: preparação de organoargila com hexadeciltrimetilamônio (HDTMA-Argila); aumento do espaçamento basal (d₀₀₁) da organoargila usando o cosurfactante octilamina e adição concomitante de uma fonte de Si, como o tetraetilortosilicato (TEOS); lavagens com etanol em HCl, secagem a 60 o C (PCH-60 A e B); calcinação a 500 o C e 700 º C (PCH 500 A/B e PCH 700), com a remoção do surfatante/co-surfactante e consequente substituição destas substâncias orgânicas por prótons que permanecem nas paredes das galerias de pilares de SiO₂ até novo tratamento porventura realizado no PCH. O material MPTS-Arg foi obtido a partir da intercalação de mercaptopropiltrimetoxisilano na argila original sob agitação durante 1 h (Arg-MPTS 1) e na argila original previamente tratada com HCl 1 mol L^-1 e sob agitação durante 2 h (Arg-MPOS 2). Os materiais (argila original, HDTMA-Argila, PCH-60, PCH-500/700 e MPTS-Arg) foram caracterizados por difração de raios-X (DRX), microscopia eletrônica de varredura acoplado a espectroscopia de raios X por dispersão de energia (MEV/ EDS), espectroscopia de absorção molecular IV com transformada de Fourier (FTIR), técnicas de análises térmicas (DTA_TG) e análises texturais, como as medidas de área superficial específica (ASEBET, ASE_Langmuir), volume total de poros (VTP) e diâmetro médio de poros (DMP). Caracterização complementar por ressonância nuclear magnética no estado sólido acoplada a espectrometria de massa (RMN-M AS) foi realizada para o PCH-500 A. Nos experimentos de adsorção de fenol, benzeno e tolueno foram utilizadas suspensões aquosas dos adsorventes contendo separadamente os adsorvatos. As concentrações de equilíbrio de fenol, tolueno e benzeno foram medidas por espectroscopia de absorção molecular na região ultravioleta, conforme método aceito e aplicado em outros estudos de adsorção. Foram obtidos os seguintes resultados: identificação do argilomineral esmectita na argila natural com espaçamento basal de 1,25nm; intercalação do HDTMA e do MPTS com expansão do d(001) para 1,95nm (HDTMA-Arg 5) e 2,1nm (MPTS-Argila 1h). Após a modificação observou-se através da análise de EDS um decréscimo das concentrações dos elementos Na, Si e Al (%) nas posições interlamelares e aumento na concentração de C. O espectro ²⁹Si MAS NMR do PCH-500 A apresentou sinais químicos dos centro Q₃ Si(OSi)₃OH e Q₄ Si(OSi)₄ que indicam a formação de sílica em sua estrutura. Os PCHs (60 e 500 A) foram classificados como mesoporosos, apresentando ASE_BET entre 417 a 446 m² g^-1 e volume total de poros (cm³ g^-1) = 0,367 - 0,369. O aumento da temperatura de calcinação do PCH 500 para 700 o C (PCH 700) propiciou decréscimos em SBET (305 m² g^-1) e diâmetro médio de poros (0.976 nm). Foi verificado a partir da avaliação das medidas dos diâmetro de poros em PCH 700 que 46% das medidas correspondem a microporos. No estudo do equilíbrio de adsorção foram obtidos os valores de K_L (L mg^-1), K_F (L mg^-1) e q_Max (mg g^-1) nos seguintes processos: (i) adsorção de fenol (1.40; 2.26 e 3.80) e tolueno (145, 7.18 e 135) em PCH-500 A; (ii) adsorção de benzeno (0.33, 41.49 e 69.81) em PCH 500 B; (iii) na adsorção de tolueno em argila-MPOS 1 (1.06, 118.9 e 146) e argila-MPOS 2 (2.1, 92 e 97); (iv) na adsorção de fenol (0.07, 0.48 e 4.44) e benzeno (0.11, 4.95 e 35.8) em HDTA-Arg 5, respectivamente. Os dados obtidos sobre a caracterização dos materiais indicaram que a formação dos PCHs propiciou grande aumento nas concentrações de Si e decréscimo nas concentrações de Al, Fe e outros elementos, devido à delaminação- exfoliação da esmectita original. Foi verificado que os materiais são mais adequados para adsorção de tolueno e benzeno do que fenol.

Sílica gel organofuncionalizada com 4-amino-5-(4-piridil) 4H-1,2,4-triazol-3-tiol (aptt): Propriedades adsortivas e eletroanalíticas

Pós-graduação em Ciência dos Materiais - FEIS

Adsorção-fotodegradação do herbicida paraquate em água pela argila Na-Bentonita e por novos materiais TiO2-Bentonita, TiO2/ZnOBentonita, Al/Fe-Bentonita e Al/Fe.Cu-Bentonita

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Adsorção de cádmio em Latossolos sob vegetação de mata nativa e cultivados

Heavy metals are found naturally in soils at low concentrations, but their content may be increased by human activity, making them one of the barriers in management of tropical soils. These chemical elements can be found in the composition of organic and inorganic fertilizers, insecticides, fungicides, mine tailings, and urban waste, and may cause serious damage to the environment and human health. Thus, adsorption studies are essential in assessing the behavior of heavy metals in the soil. The objective of this study was to evaluate the influence of soil chemical, particle size, and mineralogical properties on adsorption of cadmium (Cd), evaluated by Langmuir and Freundlich models, in Latossolos (Oxisols) with or without human activity. Soil samples were collected from the surface layer, 0.00-0.20 m, and chemical, particle size, and mineralogical analyzes were performed. In the adsorption study, concentrations of 0, 5, 25, 50, 100, 200, 300, and 400 mu g L-1 of Cd were used in the form of Cd(NO3)(2). The empirical mathematical models of Langmuir and Freundlich were used for construction of adsorption isotherms. Data were analyzed by means of multivariate statistical techniques, Cluster Analysis and Principal Component Analysis. The data from the adsorption experiment showed a good fit to the Langmuir and Freundlich models. Soils with a lower goethite/hematite ratio and greater cation exchange capacity and pH, showed higher maximum adsorption capacity of Cd.