Gas transport properties of a series of cardo polyarylethers

Gas transport of H-2, CO2, O-2, N-2, and CH4 in a series of cardo polyarylethers were examined over a temperature range of 30 similar to 100 degreesC. These polymers include three poly(aryletherketone)s, two poly(arylethersulfone)s, and one poly(aryletherketoneketone). It was found that the large length/diameter ratio of the polymer repeat unit for cardo polyaryletherketoneketone (PEKK-C) and strong intermolecular interaction in hydrogen-bonded polyarylethersulfone (PES-H) and hydrogen-bonded polyaryletherketone (PEK-H) resulted in a considerable increase in gas permselectivity. Alkyl-substituted polyaryletherketone (PEK-A), bearing a pendant bulky propyl group on the cardo ring, simultaneously exhibited 62.5% higher H-2 permeability and 59.8% higher H-2/N-2 permselectivity than unmodified poly(aryletherketone) (PEK-C). The causes of the trend were interpreted in terms of chain packing density, segmental motion ability, steric factor, and intermolecular interaction of polymers, together with gas kinetic diameter and critical temperature data.

A study of the crystallographic equivalence of ether and ketone groups in poly(aryl ether ketone)s

Crystallographic equivalence of ether and ketone in all para-substituted PAEKs crystallized in form I was discussed in this paper. In a word, crystallographic equivalence between ether and ketone groups is tenable when polymer contains only phenyl rings in the repeat unit. If a polymer contains a diphenyl group in the repeat unit, two cases should be distinguished. In the case of PEDEKK and PEEKDK, crystallographic equivalence between ether and ketone linkages is untenable, However, in the case of PEDK and PEDEKDK, crystallographic equivalence between ether and ketone linkages is still tenable.

Poly(phenylene sulfide-tetraaniline): The soluble conducting polyaniline analogue with well-defined structures

A novel conducting polymer poly(phenylene sulfide-tetraaniline) (PPSTEA), with tetraaniline (TA) and phenylene sulfide (PS) segments in its repeat unit, has been synthesized through an acid-induced polycondensation reaction of 4-methylsulfinylphenyl-capped tetraaniline. The new polymer, which represents the first soluble conducting polyaniline analogue with well-defined structure, has high molecular weight, good solubility in common solvents, and good film-forming properties. Its electrical property is analogous to polyaniline. The conductivity of preliminarily, protonic-doping PPSTEA is up to 10 degrees S/cm. This synthetic strategy appears to be general for developing novel well-defined polyaniline analogue containing much longer fixed conjugation length.

Variation of crystallographic parameters in PEEKK with heat treatment temperature

Using the wide-angle X-ray diffraction method, the variation of crystallographic parameters of poly(aryl ether ether ketone ketone) (PEEKK) has been studied in different heat treatment temperatures. All the reflections and their intensities as well as their Miller indices are presented in detail according to an orthorhombic system. The investigation indicates that the unit cell parameters a, b, c and the unit cell volume V systematically decrease with increasing heat treatment temperature. This variation is interpreted by the change of conformation of polymer molecular chains during thermal treatment. The results calculated from the formula of degree of crystallinity (W-c,W-x) for PEEKK, which was derived based on X-ray scattering intensity theory and the graphic multipeak resolution method, are compatible with the density measurement (W-c,W-d) and calorimetry (W-c,W-h) values. (C) 1997 Elesevier Science Ltd.

Analysis of tandem repeats in the genome of Chinese shrimp Fenneropenaeus chinensis

Through random sequencing, we found a total of 884000 base-pairs (bp) of random genomic sequences in the genome of Chinese shrimp (Fenneropenaeus chinensis). Using bio-soft Tandem Repeat Finder (TRF) software, 2159 tandem repeats were found, in which there were 1714 microsatellites and 445 minisatellites, accounting for 79.4% and 20.6% of repeat sequences, respectively. The cumulative length of repeat sequences was found to be 116685 bp, accounting for 13.2% of the total DNA sequence; the cumulative length of microsatellites occupied 9.78% of the total DNA sequence, and that of minisatellites occupied 3.42%. In decreasing order, the 20 most abundant repeat sequence classes were as follows: AT (557), AC (471), AG (274), AAT (92), A (56), AAG (28), ATC (27), ATAG (27), AGG (18), ACT (15), C (11), AAC (11), ACAT (11), CAGA (10), AGAA (9), AGGG (7), CAAA (7), CGCA (6), ATAA (6), AGAGAA (6). Dinucleotide repeats, not only in the aspect of the number, but also in cumulative length, were the preponderant repeat type. There were few classes and low copy numbers of repeat units of the pentanucleotide repeat type, which included only three classes: AGAGA, GAGGC and AAAGA. The classes and copy numbers of heptanucleotide, eleven-nucleotide and thirteen-nucleotide primer-number-composed repeats were distinctly less than that of repeat types beside them.

油气勘探中的弱磁异常提取与区域场分析

Petroleum and natural gas is an important strategic resources. The short of the reserves will block the development of economy and threaten the safety of nation, along with the main oil fields of our country coming to the height of power and splendor of the exploitation and exploration. Therefore, it makes a great sense to inaugurate new explorative field and increase the reserves of petroleum and natural gas. Magnetic exploration is a main method of geophysics exploration. the developing observation apparatus and the perfect processing method provide wide space for magnetic exploration in these years. The method of magnetic bright spot is an application of magnetic exploration. The vertical migration of the hydrocarbon changes physical and chemical environment above the hydrocarbon reservoir, the new environment make tervalent iron translate into bivalent iron, that produce small scale magnetic anomaly, that is magnetic bright spot. The method of magnetic bright spot explores oil and gas field by the relation between the hydrocarbon and magnetic anomaly. This paper systemically research to pick-up and identify magnetic bright spot combining an oil field item, then point out advantaged area. In order to test the result, the author use the seismic information to superpose the magnetic bright spot, that prove the magnetic bright spot is reliable. then, the author complete a software to pick and identify the magnetic bright spot. The magnetic basement is very important to research forming and evolvement of the basin, especially, it is a crucial parameter of exploring residual basin in the research on pre-Cenozoic residual. This paper put forward a new method to inverse the interface of the magnetic layer on the basis of previous work, that is the method of separation of magnetic field step by step. The theory of this method is to translate the result of magnetic layer fluctuation to the result of magnetization density change, and the magnetic layer is flat, the paper choose thickness of magnetic layer as unit thickness, and define magnetic layer as a unit-thickness layer in order to convenient calculation, at the same time, define the variational magnetization density as equivalent magnetic density. Then we translate the relation between magnetic field and layer fluctuation to the relation between magnetic field and equivalent magnetic density, then, we can obtain the layer fluctuation through calculating equivalent magnetic density. Contrast to conventional parker method, model experimentation and example checkout prove this method is effective. The merit of this method is to avoid flat result in a strongly fluctuant area because of using a uniform average depth, the result of this method is closer to the fact, and this method is to inverse equivalent magnetic density, then translate equivalent magnetic density to layer fluctuation, this lays a foundation to inverse variational magnetic density in the landscape orientation and portrait.

Adaptive Resonance Associative Map: A Hierarchical ART System for Fast Stable Associative Learning

This paper introduces a new class of predictive ART architectures, called Adaptive Resonance Associative Map (ARAM) which performs rapid, yet stable heteroassociative learning in real time environment. ARAM can be visualized as two ART modules sharing a single recognition code layer. The unit for recruiting a recognition code is a pattern pair. Code stabilization is ensured by restricting coding to states where resonances are reached in both modules. Simulation results have shown that ARAM is capable of self-stabilizing association of arbitrary pattern pairs of arbitrary complexity appearing in arbitrary sequence by fast learning in real time environment. Due to the symmetrical network structure, associative recall can be performed in both directions.

Proper expression of the O-antigen of lipopolysaccharide is essential for the virulence of Yersinia enterocolitica O:8 in experimental oral infection of rabbits

The O-antigen of lipopolysaccharide (LPS) is required for virulence in Yersinia enterocolitica serotype O:8. Here we evaluated the importance of controlling the O-antigen biosynthesis using an in vivo rabbit model of infection. Y. enterocolitica O:8 wild-type strain was compared to three mutants differing in the O-antigen phenotype: (i) the rough strain completely devoid of the O-antigen, (ii) the wzy strain that lacks the O-antigen polymerase (Wzy protein) and expresses LPS with only one repeat unit, and (iii) the wzz strain that lacks the O-antigen chain length determinant (Wzz protein) and expresses LPS without modal distribution of O-antigen chain lengths. The most attenuated strain was the wzz mutant. The wzz bacteria were cleared from the tissues by day 30, the blood parameters were least dramatic and histologically only immunomorphological findings were seen. The level of attenuation of the rough and the wzy strain bacteria was between the wild-type and the wzz strain. Wild-type bacteria were highly resistant to killing by polymorphonuclear leukocytes, the wzz strain bacteria were most sensitive and the rough and wzy strain bacteria were intermediate resistant. These results clearly demonstrated that the presence of O-antigen on the bacterial surface is not alone sufficient for full virulence, but also there is a requirement for its controlled chain length.

Re-inoculation of autoclaved soil as a non-sterile treatment for xenobiotic sorption and biodegradation studies

Autoclaved soil is commonly used for the study of xenobiotic sorption and as an abiotic control in biodegradation experiments. Autoclaving has been reported to alter soil physico-chemical and xenobiotic sorption characteristics such that comparison of autoclaved with non-autoclaved treatments in soil aging and bioavailability studies may yield misleading results. Experiments could be improved by using autoclaved soil re-inoculated with indigenous microorganisms as an additional or alternative non-sterile treatment for comparison with the sterile, autoclaved control. We examined the effect of autoclaving (3 x 1 h, 121°C, 103.5 KPa) on the physico-chemical properties of a silt loam soil (pH 7.2, 2.3% organic carbon) and the establishment of indigenous microorganisms reintroduced after autoclaving. Sterilisation by autoclaving significantly (p ≤ 0.05) decreased pH (0.6 of a unit) and increased concentrations of water-soluble organic carbon (WSOC; nontreated = 75 mg kg^-1; autoclaved = 1526 mg kg^-1). The initial first-order rate of ¹⁴C-2,4-dichloro-UL-phenol (2,4-DCP) adsorption to non-treated, autoclaved and re-inoculated soil was rapid (K₁ = 16.8-24.4 h^-1) followed by a slower linear phase (K₂). In comparison with autoclaved soil (0.038% day^-1), K₂ values were higher for re-inoculated (0.095% day^-1) and nontreated (0.181% day^-1) soil. This was attributed to a biological process. The Freundlich adsorption coefficient (K(f)) for autoclaved soil was significantly (p ≤ 0.05) higher than for re-inoculated or non-treated soil. Increased adsorption was attributed to autoclaving-induced changes to soil pH and solution composition. Glucose-induced respiration of autoclaved soil after re-inoculation was initially twice that in the non-treated control, but it decreased to control levels by day 4. This reduction corresponded to a depletion of WSOC. 2,4-DCP mineralisation experiments revealed that the inoculum of nonsterile soil (0.5 g) contained 2,4-DCP-degrading microorganisms capable of survival in autoclaved soil. The lag phase before detection of significant 2,4-DCP mineralisation was reduced (from 7 days to ≤3 days) by pre-incubation of re-inoculated soils for 7 and 14 days before 2,4-DCP addition. This was attributed to the preferential utilisation of WSOC prior to the onset of 2,4-DCP mineralisation. Cumulative ¹⁴CO₂ evolved after 21 days was significantly lower (p ≤ 0.05) from non-treated soil (25.3%) than re-inoculated soils (ca 45%). Experiments investigating sorption-biodegradation interactions of xenobiotics in soil require the physico-chemical properties of sterile and non-sterile treatments to be as comparable as possible. For fundamental studies, we suggest using re-inoculated autoclaved soil as an additional or alternative non-sterile treatment.

Recent work on entropically-driven ring-opening polymerizations: some potential applications

The entropically-driven ring-opening polymerization of macrocyclic monomers (> ca. 14 ring atoms per repeat unit) and/or macrocyclic oligomers is a relatively new method of polymer synthesis that exploits the well-known phenomenon of ring-chain equilibria. It attracts interest because of its novel features. For example, these ring-opening polymerizations emit no volatiles and little or no heat. This review considers the principles of entropically-driven ring-opening polymerizations, gives selected examples and discusses potential applications. The latter include micromolding, high throughput syntheses and the synthesis of supramolecular polymers. Copyright (c) 2005 John Wiley T Sons, Ltd.

Microblock ionomers: a new concept in high temperature, swelling-resistant membranes for PEM fuel cells

A novel series of polyaromatic ionomers with similar equivalent weights but very different sulphonic acid distributions along the ionomer backbone has been designed and prepared. By synthetically organising the sequence-distribution so that it consists of fully defined ionic segments (containing singlets, doublets or quadruplets of sulphonic acid groups) alternating strictly with equally well-defined nonionic spacer segments, a new class of polymers which may be described as microblock ionomers has been developed. These materials exhibit very different properties and morphologies from analogous randomly substituted systems. Progressively extending the nonionic spacer length in the repeat unit (maintaining a constant equivalent weight by increasing the degree of sulphonation. of the ionic segment) leads to an increasing degree of nanophase separation between hydrophilic and hydrophobic domains in these materials. Membranes cast from ionomers with the more highly phase-separated morphologies show significantly higher onset temperatures for uncontrolled swelling in water. This new type of ionomer design has enabled the fabrication of swelling-resistant hydrocarbon membranes, suitable for fuel cell operation, with very much higher ion exchange capacities (>2 meq g(-1)) than those previously reported in the literature. When tested in a fuel cell at high temperature (120 degrees C) and low relative humidity (35% RH), the best microblock membrane matched the performance of Nafion 112. Moreover, comparative low load cycle testing of membrane -electrode assemblies suggests that the durability of the new membranes under conditions of high temperature and low relative humidity is superior to that of conventional perfluorinated materials.

Female chromosomes in cockerel ejaculates

We describe a polymerase chain reaction which amplifies part of the Eco RI repeat unit of the fowl W chromosome. The resulting 447 bp fragment enables DNA from female birds to be identified. The composition of this DNA is confirmed by a nested polymerase chain reaction which specifically amplifies a known internal 263 bp region in this fragment. Using this technique it is possible to follow the fate of female cells in male germline chimaeras. The polymerase chain reaction fragment can be traced in cells of the embryonic and hatchling gonad and in adult sperm implying that cells containing the W chromosome are capable of being processed through the avian testis.

Oxide surface modification: Synthesis and characterization of zirconia-coated alumina

Four aluminas were used as Supports for impregnation with a zirconium oxide with the aim to achieve a coating, without phase separation, between Support and modifier. The Supports were impregnated with different concentrations Of zirconium aqueous resin, obtained through the polymeric precursor method. After impregnation the samples were calcined and then characterized by XRD, which led to identification of crystalline zirconia in different concentrations from each support used. Using a simple geometric model the maximum amount Of Surface modifier Oxide required for the complete coating of a support with a layer of unit cells was estimated. According to this estimate, only the support should be identified below the limit proposed and crystalline zirconium oxide Should be identified above this limit when a complete coating is reached. The results obtained From XRD agree with the estimated values and to confirm the coating, the samples were also characterized by EDS/STEM, HRTEM, XPS, and XAS. The results showed that the zirconium oxide oil the Surface of alumina Support reached the coating in the limit of 15 Zr nm(-2), without the formation of the ZrO(2) phase. (c) 2009 Elsevier Inc. All rights reserved.

Oxide surface modification: Synthesis and characterization of zirconia-coated alumina

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Association and Structure of Thermosensitive Comblike Block Copolymers in Aqueous Solutions

The structures and association properties of thermosensitive block copolymers of poly(methoxyoligo( ethylene glycol) norbornenyl esters) in D2O were investigated by small angle neutron scattering (SANS). Each block is a comblike polymer with a polynorbornene (PNB) backbone and oligo ethylene glycol (OEG) side chains (one side chain per NB repeat unit). The chemical formula of the block copolymer is (OEG3NB) 79- (OEG6.6NB) 67, where subscripts represent the degree of polymerization (DP) of OEG and NB in each block. The polymer concentration was fixed at 2.0 wt % and the structural changes were investigated over a temperature range between 25 and 68°C. It was found that at room temperature polymers associate to form micelles with a spherical core formed by the block (OEG3NB) 79 and corona formed by the block (OEG6.6NB) 67 and that the shape of the polymer in the corona could be described by the form factor of rigid cylinders. At elevated temperatures, the aggregation number increased and the micelles became more compact. At temperatures around the cloud point temperature (CPT) T ) 60 °C a correlation peak started to appear and became pronounced at 68 °C due to the formation of a partially ordered structure with a correlation length ∼349 Å.