The development of a scanning strategy for the manufacture of porous biomaterials by selective laser melting.

Porous structures are used in orthopaedics to promote biological fixation between metal implant and host bone. In order to achieve rapid and high volumes of bone ingrowth the structures must be manufactured from a biocompatible material and possess high interconnected porosities, pore sizes between 100 and 700 microm and mechanical strengths that withstand the anticipated biomechanical loads. The challenge is to develop a manufacturing process that can cost effectively produce structures that meet these requirements. The research presented in this paper describes the development of a 'beam overlap' technique for manufacturing porous structures in commercially pure titanium using the Selective Laser Melting (SLM) rapid manufacturing technique. A candidate bone ingrowth structure (71% porosity, 440 microm mean pore diameter and 70 MPa compression strength) was produced and used to manufacture a final shape orthopaedic component. These results suggest that SLM beam overlap is a promising technique for manufacturing final shape functional bone ingrowth materials.

Thermomechanical analyses of ultrasonic welding process using thermal and acoustic softening effects

Ultrasonic welding process is a rapid manufacturing process used to weld thin layers of metal at low temperatures and low energy consumption. Experimental results have shown that ultrasonic welding is a combination of both surface (friction) and volume (plasticity) softening effects. In the presented work, a very first attempt has been made to simulate the ultrasonic welding of metals by taking into account both of these effects (surface and volume). A phenomenological material model has been proposed which incorporates these two effects (i.e. surface and volume). The thermal softening due to friction and ultrasonic (acoustic) softening has been included in the proposed material model. For surface effects a friction law with variable coefficient of friction dependent upon contact pressure, slip, temperature and number of cycles has been derived from experimental friction tests. Thermomechanical analyses of ultrasonic welding of aluminium alloy have been performed. The effects of ultrasonic welding process parameters, such as applied load, amplitude of ultrasonic vibration, and velocity of welding sonotrode on the friction work at the weld interface are being analyzed. The change in the friction work at the weld interface has been explained on the basis of softening (thermal and acoustic) of the specimen during the ultrasonic welding process. In the end, a comparison between experimental and simulated results has been presented showing a good agreement. © 2008 Elsevier Ltd. All rights reserved.

Theoretical and FE analysis of ultrasonic welding of aluminum alloy 3003

Ultrasonic welding (consolidation) process is a rapid manufacturing process that is used to join thin layers of metal at low temperature and low energy consumption. Experimental results have shown that ultrasonic welding is a combination of both surface (friction) and volume (plasticity) softening effects. In the presented work, an attempt has been made to simulate the ultrasonic welding of metals by taking into account these effects (surface and volume). A phenomenological material model has been proposed, which incorporates these two effects (i.e., surface and volume). The thermal softening due to friction and ultrasonic (acoustic) softening has been included in the proposed material model. For surface effects, a friction law with variable coefficient of friction that is dependent on contact pressure, slip, temperature, and number of cycles has been derived from experimental friction tests. The results of the thermomechanical analyses of ultrasonic welding of aluminum alloy have been presented. The goal of this work is to study the effects of ultrasonic welding process parameters, such as applied load, amplitude of ultrasonic oscillation, and velocity of welding sonotrode on the friction work at the weld interface. The change in the friction work at the weld interface has been explained on the basis of softening (thermal and acoustic) of the specimen during the ultrasonic welding process. In the end, a comparison between experimental and simulated results has been presented, showing a good agreement. Copyright © 2009 by ASME.

Modelling and characterization of ultrasonic consolidation process of Aluminium alloys

Ultrasonic consolidation process is a rapid manufacturing process used to join thin layers of metal at low temperatures and low energy consumption. In this work, finite element method has been used to simulate the ultrasonic consolidation of Aluminium alloys 6061 (AA-6061) and 3003 (AA-3003). A thermomechanical material model has been developed in the framework of continuum cyclic plasticity theory which takes into account both volume (acoustic softening) and surface (thermal softening due to friction) effects. A friction model based on experimental studies has been developed, which takes into account the dependence of coefficient of friction upon contact pressure, amount of slip, temperature and number of cycles. Using the developed material and friction model ultrasonic consolidation (UC) process has been simulated for various combinations of process parameters involved. Experimental observations are explained on the basis of the results obtained in the present study. The current research provides the opportunity to explain the differences of the behaviour of AA-6061 and AA-3003 during the ultrasonic consolidation process. Finally, trends of the experimentally measured fracture energies of the bonded specimen are compared to the predicted friction work at the weld interface resulted from the simulation at similar process condition. Similarity of the trends indicates the validity of the developed model in its predictive capability of the process. © 2008 Materials Research Society.

Composition and cure temperature: The influence on properties of final flexible PU cold cure foam parts

Foams are cellular structures, produced by gas bubbles formed during the polyurethane polymerization mixture. Flexible PU foams meet the following two criteria: have a limited resistance to an applied load, being both permeable to air and reversibly deformable. There are two main types of flexible foams, hot and cold cure foams differing in composition and processing temperatures. The hot cure foams are widely applied and represent the main composition of actual foams, while cold cure foams present several processing and property advantages, e.g, faster demoulding time, better humid aging properties and more versatility, as hardness variation with index changes are greater than with hot cure foams. The processing of cold cure foams also is attractive due to the low energy consumption (mould temperature from 30 degrees to 65 degrees C) comparatively to hot cure foams (mould temperature from 30 degrees to 250 degrees C). Another advantage is the high variety of soft materials for low temperature processing moulds. Cold cure foams are diphenylmethane diisocyanate (MDI) based while hot cure foams are toluene diisocyanate (TDI) based. This study is concerned with Viscoelastic flexible foams MDI based for medical applications. Differential Scanning Calorimetry (DSC) was used to characterize the cure kinetics and Dynamical Mechanical Analisys to collect mechanical data. The data obtained from these two experimental procedures were analyzed and associated to establish processing/properties/operation conditions relationships. These maps for the selection of optimized processing/properties/operation conditions are important to achieve better final part properties at lower costs and lead times.

The effect of thermal conductivity of RIM moulds in kinetics cure

Reaction Injection Moulding (RIM) is a moulding technology used for the production of large size and complex plastic parts. The RIM process is characterized essentially by the injection of a highly reactive chemical system (usually polyurethane) and fast cure, in a mould properly closed and thermally controlled. Several studies show that rapid manufacturing moulds obtained in epoxy resins for Thermoplastic Injection Moulding (TIM) affect the moulding process and the final properties of parts. The cycle time and mechanical properties of final parts are reduced, due to a low thermal conductivity of epoxy materials. In contrast, the low conductivity of materials usually applied for the rapid manufacturing of RIM moulds, increase the mechanical properties of final injected parts and reduce the cycle time. This study shows the effect of the rapid manufacturing moulds material during the RIM process. Several materials have been tested for rapid manufacturing of RIM moulds and the analysis of both, temperature profile of moulded parts during injection and the cure data experimentally obtained in a mixing and reaction cell, allow to determine and model the real effect of the mould material on the RIM process.

Geometric and material constraints in parametric modelling : the design to fabrication process

Parametric modelling, commonly used in the automotive and aerospace industries, has recently been adopted in the architecture and construction fields. The ability to design small repeatable components and apply them to a larger governing surface geometry is one area of parametric modelling that has great design potential. This two level modelling control, of component and overall surface, can allow designers to explore new types of form generation subject to parametric constraints. This paper reports on the design to fabrication process using repeatable components over a governing or carrier surface. The paper reports on our study of the requirements and possible solutions for successfully controlling a repeatable element, known as a Representative Volumetric Element (RVE), using geometric parameters of a larger governing surface geometry and material properties. This modelling process, coupled with Rapid
Manufacturing (RM) and Computer Numerically Controlled (CNC) machines has the potential to significantly reduce the interface between design and fabrication.

Metodologia de design mediada por protótipos

Pós-graduação em Design - FAAC

O design industrial e as engenharias: uma possibilidade de integração por intermédio da engenharia reversa

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Anisotropic Mechanical Properties of ABS Parts Fabricated by Fused Deposition Modelling

In recent years, layered manufacturing (LM) processes have begun to progress from rapid prototyping techniques towards rapid manufacturing methods, where the objective is now to produce finished components for potential end use in a product (Caulfield et al., 2007). LM is especially promising for the fabrication of specific need, low volume products such as replacement parts for larger systems. This trend accentuates the need for a thorough understanding of the associated mechanical properties and the resulting behavior of parts produced by layered methods. Not only must the base material be durable, but the mechanical properties of the layered components must be sufficient to meet in-service loading and operational requirements, and be reasonably comparable to parts produced by more traditional manufacturing techniques. This chapter presents the details of a study completed to quantitatively analyze the potential of fused deposition modelling to fully evolve into a rapid manufacturing tool. The project objective is to develop an understanding of the dependence of the mechanical properties of FDM parts on raster orientation and to assess whether these parts are capable of maintaining their integrity while under service loading. The study examines the effect of fiber orientation, i.e. the direction of the polymer beads relative to the loading direction of the part, on a variety of important mechanical properties of ABS components fabricated by fused deposition modeling. Tensile, compressive, flexural, impact, and fatigue strength properties of FDM specimens are examined, evaluated, and placed in context in comparison with the properties of injection molded ABS parts.

Optimierung der Eigenschaften von thermoplastischen Lasersinter-Bauteilen

Das Lasersintern (LS) hat sich als generatives Verfahren zur schichtweisen Fertigung von Modellen und Prototypen aus CAD-Daten etabliert. Die Möglichkeit werkzeuglos beliebig komplexe Bauteile zu erstellen birgt großes Potential für die zukünftige Fertigung von Einzelstücken und Kleinserien. Da die verfügbare Technologie starke Schwankung der Qualität mit sich bringt, stellt sich jedoch die Frage nach der prinzipiellen Leistungsfähigkeit des Verfahrens. Die Professur Fertigungstechnik an der Universität Duisburg-Essen verfügt über eine Sinterstation 2000 und hat sich näher mit dieser Problematik befasst um zu untersuchen, welche Qualität bei gegebener Anlagentechnik unter Verwendung eines gängigen Lasersinter-Werkstoffes erreichbar ist.

Zukunftspotential durch Design und RM

Im Bereich Medical Design spielen eine hohe Funktionalität und eine angenehme Handhabung eine grosse Rolle. In den Engineering-Projekten der Erdmann Design AG werden kühne Ideen in den Raum gesetzt die das Klima für Innovationen fördern. „Innovation entsteht aus elementarer Neugier und Lust auf eine bessere Zukunft“, sagt Raimund Erdmann. „Wir beraten mit unseren Feed Forward Methoden Start-up Firmen, Kleinunternehmen wie auch etliche, börsenkotierte, international aktive Unternehmen. Und das für excellentes Industrial Design, Corporate Design und Design Management“ mit den überzeugenden Möglichkeiten des Rapid Manufacturing.Im Bereich Medical Design spielen eine hohe Funktionalität und eine angenehme Handhabung eine grosse Rolle. In den Engineering-Projekten der Erdmann Design AG werden kühne Ideen in den Raum gesetzt die das Klima für Innovationen fördern. „Innovation entsteht aus elementarer Neugier und Lust auf eine bessere Zukunft“, sagt Raimund Erdmann. „Wir beraten mit unseren Feed Forward Methoden Start-up Firmen, Kleinunternehmen wie auch etliche, börsenkotierte, international aktive Unternehmen. Und das für excellentes Industrial Design, Corporate Design und Design Management“ mit den überzeugenden Möglichkeiten des Rapid Manufacturing.

SLM von Polylactiden zur Herstellung von resorbierbaren Implantaten

Rapid Manufacturing von individuellen Implantaten mittels Selective Laser Melting (SLM) wurde für metallische Standardwerkstoffe in der Medizintechnik (Titanlegierungen, Kobalt-Chrom-Legierungen, Stahl) realisiert. Dies sind permanente Implantate, die entweder dauerhaft im Körper verbleiben oder in einer zweiten Operation entfernt werden. Eine vom ILT mittels SLM hergestellte Hüftpfanne aus TiAl6V4 konnte bereits erfolgreich im Patienten implantiert werden. Die regenerative Therapie ist jedoch die klinisch bevorzugte Strategie. Das bedeutet, dass der Selbstheilungsprozess des menschlichen Körpers für die Heilung von großen Knochendefekten genutzt wird. Ein neuer Ansatz zur Implantatfertigung folgt dieser Strategie. Der SLM-Prozess wird für die Verarbeitung von bioresorbierbaren Werkstoffen entwickelt um individuelle Implantate zu fertigen, die im Körper abgebaut und durch körpereigenes Knochengewebe ersetzt werden. Diese Arbeit beschreibt die Qualifizierung des SLM Verfahrens für die Verarbeitung von einem Kompositmaterial aus Polylactid / β-Tricalciumphosphat (PDLLA/β-TCP).

„Pulverbettbasiertes Strahlschmelzen – neue Forschungserkenntnisse“

Auf dem Weg vom Rapid Prototyping zum Rapid Manufacturing ist erhöhte Prozesssicherheit sowie die Beherrschung verfahrensspezifischer Phänomene notwendig, um die immer weiter steigenden und konkreteren Bauteilanforderungen zu erfüllen. Dazu wurden diverse im SLM-Prozess auftretende Effekte untersucht. Basis der vorgestellten Entwicklungen sind grundlegende Erkenntnisse zur Oberflächenqualität von SLM-Bauteilen und Einflussgrößen auf Dichte und mechanische Eigenschaften der Bauteile verschiedener Werkstoffe. Ergebnis sind verschiedene Weiterentwicklungen der Standardbelichtungsstrategie, wodurch etwa Eigenspannungseffekte und Spritzerbildung positiv beeinflusst werden können.