On crack path stability in a layered material

Crack paths in an elastic layer on top of a substrate are considered. Crack growth is initiated from an edge crack in the layer. The plane of the initially straight crack forms an angle to the free surface. The load consists of a pair of forces applied at the crack mouth and parallel to the interface. Crack paths are calculated using a boundary element method. Crack growth is assumed to proceed along a path for which the mode II stress intensity factor vanishes. The inclination and the length of the initial crack are varied. The effect of two different substrates on the crack path evolution is demonstrated. A crack path initially leading perpendicularly to the interface is shown to be directionally unstable for a rigid substrate. Irrespective of its initial angle, the crack does not reach the interface, but reaches the free surface if the layer is infinitely long. At finite layer length the crack reaches the upper free surface if the initial crack inclination to the surface is small enough. For an inextendable flexible substrate, on the other hand, the crack reaches the interface if its initial inclination is large enough. For the flexible substrate an unstable path parallel with the sides of an infinitely long layer is identified. The results are compared with experimental results and discussed in view of characterisation of directionally unstable crack paths. The energy release rate for an inclined edge crack is determined analytically.

Parameter-transformation relations for traveling-wave solutions of kdv-burgers equation

 Burgers suggested that the main properties of free-turbulence in the boundless area without basic flow might be understood with the aid of the following equation, which was much simpler than those of fluid dynamics, 更多还原

Effect of phase-transformation on mechanical-behavior of dual-phase steel plate

The mechanical behavior of dual phase steel plates is affected by internal stresses created during martensite transformation. Analytical modelling of this effect is made by considering a unit cell made of martensite inclusion in a ferrite matrix. A large strain finite element analysis is then performed to obtain the plane stress deformation state. Displayed numerically are the development of the plastic zone and distribution of local state of stress and strain. Studied also are the shape configuration of the martensite (hard-phase) that influences the interfacial condition as related to stress transmission and damage. Internal stresses are found to enhance the global flow stress after yield initiation in the ferrite matrix. Good agreement is obtained between the analytical results and experimental observations.

Temperature transformation in relativistic thermodynamics

This paper reviews conflicting results on relativistic transformation formula for tem-perature obtained by different authors in the last half century, discusses the proper expres-sion for elementary work done under reversible processes, and presents a correct derivationof the transformation formula, rather similar in spirit to that of Einstein. It is pointed outthat the point of view adopted by Eddington, Ott, Mφller and Landsberg are erroneous,and that by correctly carrying out detailed analysis for Mφller's working model, which wasoriginally proposed to disprove Planck-Einstein result, we have arrived instead at a result incomplete agreement with that of Planck-Einstein. Thercupon this long standing controversyover the temperature transformation dilemma for relativistic thermodynamics is clarified.

Path Planner for Intelligent Laser Surface Modification

An optimal algorithm of manufacturing path planner for intelligent laser surface modification is presented. Elements included in the optimal objective have been analyzed. A 6-D manufacture trace that satisfies the requirements of special craft and 5-axis laser processing robot system has been generated from the path planner by method of parallel section in which combinations of modification spots size with curvature of processing surfaces and modification craft parameters are considered. Related experiments have been successfully carried out with the computer integrated multifunctional laser manufacturing system.

Numerical Simulation of Pulsed Laser Transformation Hardening

A novel pulsed laser surface processing technology is introduced, which can make use of the spatial and temporal profile of laser pulse to obtain ideal hardening parameters. The intensity distribution of laser pulse is spatially and temporally controlled by using laser shape transformation technology. A 3D numerical model including multi-phase transformations is established to explore material microstructure evolution induced by temperature field evolution. The influences of laser spatial-temporal profiles on hardening parameters are investigated. Different from the continuous laser processing technology, results indicate that spatial and temporal profiles are important factors in determining processing quality during pulsed laser processing method.

Using forecasts to protect Federal facilities in the path of Hurricane Isabel

Hurricane Isabel made landfall as a Category 2 Hurricane on 18 September 2003, on the North Carolina Outer Banks between Cape Lookout and Cape Hatteras, then coursed northwestward through Pamlico Sound and west of Chesapeake Bay where it downgraded to a tropical storm. Wind damage on the west and southwest shores of Pamlico Sound and the western shore of Chesapeake Bay was moderate, but major damage resulted from the storm tide. The NOAA, National Ocean Service, National Centers for Coastal Ocean Sciences, Center for Coastal Fisheries and Habitat Research at Beaufort, North Carolina and the Center for Coastal Environmental Health and Biomedical Research Branch at Oxford, Maryland have hurricane preparedness plans in place. These plans call for tropical storms and hurricanes to be tracked carefully through NOAA National Weather Service (NWS) watches, warnings, and advisories. When a hurricane watch changes to a hurricane warning for the areas of Beaufort or Oxford, documented hurricane preparation plans are activated. Isabel exacted some wind damage at both Beaufort and Oxford. Storm tide caused damage at Oxford, where area-wide flooding isolated the laboratory for many hours. Storm tide also caused damage at Beaufort. Because of their geographic locations on or near the open ocean (Beaufort) or on or near large estuaries (Beaufort and Oxford), storm tide poses a major threat to these NOAA facilities and the safety of federal employees. Damage from storm surge and windblown water depends on the track and intensity of a storm. One tool used to predict storm surge is the Sea, Lake, and Overland Surges from Hurricanes (SLOSH) model of the NWS, which provides valuable surge forecasts that aid in hurricane preparation.

Assisting blog publication: annotation, model transformation, and crossblogging techniques

Although blogs exist from the beginning of the Internet, their use has considerablybeen increased in the last decade. Nowadays, they are ready for being used bya broad range of people. From teenagers to multinationals, everyone can have aglobal communication space.Companies know blogs are a valuable publicity tool to share information withthe participants, and the importance of creating consumer communities aroundthem: participants come together to exchange ideas, review and recommend newproducts, and even support each other. Also, companies can use blogs for differentpurposes, such as a content management system to manage the content of websites,a bulletin board to support communication and document sharing in teams,an instrument in marketing to communicate with Internet users, or a KnowledgeManagement Tool. However, an increasing number of blog content do not findtheir source in the personal experiences of the writer. Thus, the information cancurrently be kept in the user¿s desktop documents, in the companies¿ catalogues,or in another blogs. Although the gap between blog and data source can be manuallytraversed in a manual coding, this is a cumbersome task that defeats the blog¿seasiness principle. Moreover, depending on the quantity of information and itscharacterisation (i.e., structured content, unstructured content, etc.), an automaticapproach can be more effective.Based on these observations, the aim of this dissertation is to assist blog publicationthrough annotation, model transformation and crossblogging techniques.These techniques have been implemented to give rise to Blogouse, Catablog, andBlogUnion. These tools strive to improve the publication process considering theaforementioned data sources.