Advances in the analysis of short span railway bridges for high-speed lines

The physical model based on moving constant loads is widely used for the analysis of railway bridges. Nevertheless, the moving loads model is not well suited for the study of short bridges (L⩽20–25 m) since the results it produces (displacements and accelerations) are much greater than those obtained from more sophisticated ones. In this paper two factors are analysed which are believed to have an influence in the dynamic behaviour of short bridges. These two factors are not accounted for by the moving loads model and are the following: the distribution of the loads due to the presence of the sleepers and ballast layer, and the train–bridge interaction. In order to decide on their influence several numerical simulations have been performed. The results are presented and discussed herein.

Identification of pressures and maintenance in railway tunnels

This paper describes an interactive set of tools used to determine the safety of tunnels and to provide data for the decision making of its mainteinance. Although, no doubt, there are still several drawbacks in the difficult procedures in use it is clear that the way is promising and future improvements both in experimental and analytical methods will increase our understanding of this matter.

The Dynamics of High-Speed Railway Bridges: A Review of Design Issues and New Research for Lateral Dynamics

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for the consideration of safe running conditions for the trains. In this work we start by reviewing the relevance of some basic design aspects. The significance of impact factor envelopes for moving loads is considered first. Resonance which may be achieved for high-speed trains requires dynamic analysis, for which some key aspects are discussed. The relevance of performing a longitudinal distribution of axle loads, the number of modes taken in analysis, and the consideration of vehicle-structure interaction are discussed with representative examples. The lateral dynamic effects of running trains on bridges is of importance for laterally compliant viaducts, such as some very tall structures erected in new high-speed lines. The relevance of this study is mainly for the safety of the traffic, considering both internal actions such as the hunting motion as well as external actions such as wind or earthquakes [1]. These studies require three-dimensional dynamic coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework [2]. The wheel-rail contact has been considered using a FastSim algorithm which provides a compromise between accuracy and computational cost, and captures the main nonlinear response of the contact interface. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the dynamic interaction between bridge and vehicle. The second application is to a real HS viaduct with a long continuous deck and tall piers and high lateral compliance [3]. The results show the safety of the traffic as well as the importance of considering features such as track alignment irregularities.

Efectos dinámicos laterales en vehículos y puentes ferroviarios sometidos a la acción de vientos transversales

En las últimas décadas el aumento de la velocidad y la disminución del peso de los vehículos ferroviarios de alta velocidad ha provocado que aumente su riesgo de vuelco. Además, las exigencias de los trazados de las líneas exige en ocasiones la construcción de viaductos muy altos situados en zonas expuestas a fuertes vientos. Esta combinación puede poner en peligro la seguridad de la circulación. En esta tesis doctoral se estudian los efectos dinámicos que aparecen en los vehículos ferroviarios cuando circulan sobre viaductos en presencia de vientos transversales. Para ello se han desarrollado e implementado una serie de modelos numéricos que permiten estudiar estos efectos de una forma realista y general. Los modelos desarrollados permiten analizar la interacción dinámica tridimensional tren-estructura, formulada mediante coordenadas absolutas en un sistema de referencia inercial, en un contexto de elementos _nitos no lineales. Mediante estos modelos se pueden estudiar de forma realista casos extremos como el vuelco o descarrilamiento de los vehículos. Han sido implementados en Abaqus, utilizando sus capacidades para resolver sistemas multi-cuerpo para el vehículo y elementos finitos para la estructura. La interacción entre el vehículo y la estructura se establece a través del contacto entre rueda y carril. Para ello, se han desarrollado una restricción, que permite establecer la relación cinemática entre el eje ferroviario y la vía, teniendo en cuenta los posibles defectos geométricos de la vía; y un modelo de contacto rueda-carril para establecer la interacción entre el vehículo y la estructura. Las principales características del modelo de contacto son: considera la geometría real de ambos cuerpos de forma tridimensional; permite resolver situaciones en las que el contacto entre rueda y carril se da en más de una zona a la vez; y permite utilizar distintas formulaciones para el cálculo de la tensión tangencial entre ambos cuerpos. Además, se ha desarrollado una metodología para determinar, a partir de formulaciones estocásticas, las historias temporales de cargas aerodinámicas debidas al viento turbulento en estructuras grandes y con pilas altas y flexibles. Esta metodología tiene cuenta la variabilidad espacial de la velocidad de viento, considerando la correlación entre los distintos puntos; considera las componentes de la velocidad del viento en tres dimensiones; y permite el cálculo de la velocidad de viento incidente sobre los vehículos que atraviesan la estructura. La metodología desarrollada en este trabajo ha sido implementada, validada y se ha aplicado a un caso concreto en el que se ha estudiado la respuesta de un tren de alta velocidad, similar al Siemens Velaro, circulando sobre el viaducto del río Ulla en presencia viento cruzado. En este estudio se ha analizado la seguridad y el confort de la circulación y la respuesta dinámica de la estructura cuando el tren cruza el viaducto. During the last decades the increase of the speed and the reduction of the weight of high-speed railway vehicles has led to a rise of the overturn risk. In addition, the design requests of the railway lines require some times the construction of very tall viaducts in strong wind areas. This combination may endanger the traffic safety. In this doctoral thesis the dynamic effects that appear in the railway vehicles when crossing viaducts under strong winds are studied. For this purpose it has been developed and implemented numerical models for studying these effects in a realistic and general way. The developed models allow to analyze the train-structure three-dimensional dynamic interaction, that is formulated by using absolute coordinates in an inertial reference frame within a non-linear finite element framework. By means of these models it is possible to study in a realistic way extreme situations such vehicle overturn or derailment. They have been implemented for Abaqus, by using its capabilities for solving multi-body systems for the vehicle and finite elements for the structure. The interaction between the vehicle and the structure is established through the wheel-rail contact. For this purpose, a constraint has been developed. It allows to establish the kinematic relationship between the railway wheelset and the track, taking into account the track irregularities. In addition, a wheel-rail contact model for establishing the interaction of the vehicle and the structure has been developed. The main features of the contact model are: it considers the real geometry During the last decades the increase of the speed and the reduction of the weight of high-peed railway vehicles has led to a rise of the overturn risk. In addition, the design requests of the railway lines require some times the construction of very tall viaducts in strong wind areas. This combination may endanger the traffic safety. In this doctoral thesis the dynamic effects that appear in the railway vehicles when crossing viaducts under strong winds are studied. For this purpose it has been developed and implemented numerical models for studying these effects in a realistic and general way. The developed models allow to analyze the train-structure three-dimensional dynamic interaction, that is formulated by using absolute coordinates in an inertial reference frame within a non-linear finite element framework. By means of these models it is possible to study in a realistic way extreme situations such vehicle overturn or derailment. They have been implemented for Abaqus, by using its capabilities for solving multi-body systems for the vehicle and finite elements for the structure. The interaction between the vehicle and the structure is established through the wheel-rail contact. For this purpose, a constraint has been developed. It allows to establish the kinematic relationship between the railway wheelset and the track, taking into account the track irregularities. In addition, a wheel-rail contact model for establishing the interaction of the vehicle and the structure has been developed. The main features of the contact model are: it considers the real geometry

Static Pressure Impact on Aerodynamics of High Speed Railway Tunnels

A pressure wave is generated when a high speed train enters a tunnel. This wave travels along the tunnel back and forth, and is reflected at the irregularities of the tunnel duct (section changes, chimneys and tunnel ends). The pressure changes are associated to these waves can have an effect on passengers if the trains are not suitably sealed or pressurized. The intensity of the waves depends mainly on the train speed, and on the blockage ratio (train-section-to- tunnel-section area ratio). As the intensity of the waves is limited by regulations, and also by the effects on passengers and infrastructures, the sizing of the tunnel section area is largely influenced by the maximum train speed allowed in the tunnel. The aim of this study is to analyse the increase in cost in a tunnel due to the existence of this difference in ground level, and evaluate the increase of construction costs that this elevation might involve.

Great marquee in the new railway station on Málaga

The commercial centre VIALIA and the new railway station of the AVE (high speed train) in Malaga was inaugurated in November 2006, just on the place of the former railway station. The new railway station with an investment of 134,7 million Euros occupies a surface of 51.377 m2, five times the surface of the former station. The enclosure is the biggest intermodal and commercial centre of Spain which comprises a parking of 21.000 m2 for 1300 parking places, one commercial area and a hotel with a total extension constructed of approximately 100.000 m2. The spaces of leisure contain cinemas, shops, restaurants, bowling, gymnasium, swimming pool and zones of passenger's traffic.

Bridges E-2 and E-3 in the new railway to the Northwest of Spain

During the years 2001 to 2007 it has been constructed in Spain the new railway line of high speed (L. H. S.)that connects Madrid with Valladolid with a length of 179.6 kilometres.

The effect of Windbreaks on Railway Overheads subject to Cross-Winds at O Eixo Viaduct

A measurement investigation, at ADIF's test site at the O Eixo viaduct which is on the Spanish Santiago-Ourense high speed railway line, has been carried out during the last year. The main goal of the investigation is to study the effect of the cross-wind on railway overheads (catenaries) and the influence of the presence of windbreaks on the wind-induced motion of the railway overhead. A description of the O Eixo viaduct test site is presented in this paper, including the installed windbreaks, the sensor and power supply systems. Three catenary spans has been instrumented at the center point of the catenary span contact wire with one ultrasonic anemometer and two unidirectional accelerometers. Additionally, another ultrasonic anemometer placed in the central catenary span has been installed to provide reference wind data. Wind roses of wind speed and standard deviation of the accelerometers are presented. As expected, the four wind roses look very similar and the two dominant directions close to the perpendicular to the bridge longitudinal axes, north and south have been identified. The wind roses of the standard deviation of the acceleration shows that the acceleration of the catenary contact wire is related to the directions of the two dominant winds. The vertical standard deviation of the acceleration is higher than the horizontal one for the spans with windbreaks. It has also been observed that the presence of the windbreaks modifies the wind flow leading to a wind-induced motion of the catenary contact wire which shows a higher variability than the corresponding unprotected case. On the one hand, the baseline southerly wind configuration (south wind, windbreaks in the windward side and catenary in the leeward side) influence both the mean speed at the catenary and the turbulence intensity. On the other hand, the northerly wind configuration, windbreaks in the leeward side and catenary in the windward side, provide a reference to the response of the catenary for an unprotected railway overhead, and, as it is expected, the windbreak influence is much more reduced compared to the southerly wind configuration. Both the height of the windbreak and the eaves contribute to the increase in the turbulence intensity at the catenary contact wire height. It can be seen that the height of the windbreak plays a crucial role in the increase of turbulence intensity, much more intense than the presence of the windbreak eave.

Dynamics of high-speed railway bridges: review of design issues and new research for lateral dynamics

Revisión y puesta al día de la publicaciones relacionadas con el diseño de puentes de ferrocarril de alta velocidad y nuevas investigaciones sobre dinámica lateral.

Analysis of lateral dynamics of railway vehicles on viaducts with coupled models

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models, and consideration of wheel to rail contact, a phenomenon which is complex and costly to model in detail. We describe here a fully nonlinear coupled model, described in absolute coordinates and incorporated into a commercial finite element framework. Two applications are presented, firstly to a vehicle subject to a strong wind gust traversing a br idge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle. The second application is to a real viaduct in a high-speed line, with a long continuous deck and tall piers with high lateral compliance. The results show the safety of the traffic as well as the relevance of considering the wind action and the nonlinear response.

Great marquee for high-speed trains in the new railway station of Malaga

The commercial centre VIALIA and the new railway station of the AVE (high speed train) in Malaga was inaugurated in November 2006, just on the place of the former railway station. The new railway station with an investment of 134,7 million Euros occupies a surface of 51.377 m2, five times the surface of the former station. The enclosure is the biggest intermodal and commercial centre of Spain which comprises a parking of 21.000 m2 for 1300 parking places, one commercial area and a hotel with a total extension constructed of approximately 100.000 m2. The spaces of leisure contain cinemas, shops, restaurants, bowling, gymnasium, swimming pool and zones of passenger's traffic.

Vibrations of Short Span Railway Bridges for High Speed Lines

The physical model based on moving constant loads is widely used for the analysis of railway bridges. Nevertheless, this model is not well-suited for the study of short span bridges (L<=15-20 m), and the results it produces (displacements and accelerations) are much greater than those obtained experimentally. In this paper two factors are analysed which are believed to have an influence in the dynamic behaviour of short bridges. These two factors are not accounted for by the moving loads model and are the following: the distribution of the loads due to the presence of the sleepers and ballast layer, and the train-bridge interaction. Several numerical simulations have been performed in order to decide on their influence, and the results are presented and discussed herein.

Measuring dynamic effects on underpasses of high-speed railway lines

Underpasses are common in modern railway lines. Wildlife corridors and drainage conduits often fall into this category of partially buried structures. Their dynamic behaviour has received far less attention than that of other structures such as bridges, but their large number makes their study an interesting challenge in order to achieve safe and cost-effective structures. As ballast operations are a key life cycle cost, and excessive vibrations increase the need of ballast regulation in order to ensure track geometry, special attention is paid to accelerations, the values of which should be limited to avoid track instability according to Eurocode. In this paper, the data obtained during on site measurements on culverts belonging to a Spanish high-speed train line are presented. A set of six rectangular-shaped, closed-frame underpasses were monitored under traffic loading. Acceleration records at different points of the structures are presented and discussed. They reveal a non-uniform dynamic response of the roof-slab, with the highest observed values below the occupied track. Also, they indicate that the dynamic response is important up to frequencies higher than those usually observed for standard simply supported bridges. Finally, they are used to obtain a heuristic rule to estimate acceleration levels on the roof-slab.

Moving loads on railway bridges: The Spanish Code approach

This paper presents the results of part of the research carried out by a committee in charge of the elaboration of the new Spanish Code of Actions in Railway Bridges. Following the work developed by the European Rail Research Institute (ERRI), the dynamic effects caused by the Spanish high-speed train TALGO have been studied and compared with other European trains. A simplified envelope of the impact coefficient is also presented. Finally, the train-bridge interactions has been analysed and the results compared with those obtained from simple models based on moving loads.

On the use of trenches and walls on the control of ground transmitted railway vibrations

An actual case of an underground railway in the neighbourhood of habitation buildings has been analyzed. The study has been based on a twodimensional BEM model including a tunnel and a typical building. The soil properties were obtained using geophysical techniques. After a sensitivity study, the model has been simplyfied and validated by comparison with "in situ" measurements. Using this simplyfied model, a parametric study has been done including trenches and walls of different materials and different depths at two different distances from the tunnel. The reductions obtained with the different solutions can then be compared.