Shear Bond Strength of A Sealant to Contaminated-Enamel Surface: Influence of Erbium : Yttrium-Aluminum-Garnet Laser Pretreatment

Salivary contamination is one of the factors that can disturb the sealing process and interfere in the longevity of pit and fissure sealants. Erbium : yttrium-aluminum-garnet (Er : YAG) laser could influence the bond strength of enamel and increase the acid resistance. To evaluate the influence of Er : YAG laser on the shear bond strength of a sealant to a salivary contaminated enamel surface. Twenty-four third molars had the roots sectioned 2 mm coronal to the cementoenamel junction. The crowns were mesiodistally sectioned providing 48 halves that were embedded in polyester resin. Enamel was flattened and a 2-mm diameter bonding area was demarcated. Specimens were randomly assigned to two groups according to the superficial pretreatment-37% phosphoric acid (A) and Er : YAG laser (80 mJ/2 Hz) + phosphoric acid (L), which were subdivided into two groups (N = 12), without salivary contamination (C) and with salivary contamination (SC). To contaminate the specimens, 0.25 mL of human fresh saliva was applied for 20 seconds and then dried. Fluroshield sealant was applied in all specimens. After storage, shear bond strength of samples were tested in a universal testing machine. Means in MPa were: AC-14.61 (+/- 2.52); ASC-6.66 (+/- 2.34); LC-11.91 (+/- 1.34); and LSC-2.22 (+/- 0.66). Statistical analysis revealed that surfaces without salivary contamination and with acid treatment had the highest mean (p < 0.05). The group with salivary contamination treated by Er : YAG laser followed by phosphoric acid application presented the lowest bond values (p < 0.05). The phosphoric acid etching under dry condition yielded better bonding performance. Er : YAG laser was not able to increase the effectiveness of conventional acid etching of enamel in the bond of sealants in both dry and wet conditions. Under the conditions of this study, the conventional etching protocol (phosphoric acid without salivary contamination) is still preferable to laser-conditioning enamel surface prior to sealant application.

Evaluation of the Abrasiveness of Dentifrices for Complete Dentures

Purpose: This study analyzed the surface roughness and weight loss in Plex Glass specimens caused by dentifrices, one conventional (Sorriso) and three specific for dentures. Materials and Methods: Specimens (n = 6) of Plex Glass were divided into 5 groups including: negative control (water); positive control 1 (Sorriso) and 2 (Corega Brite); Experimental 1 (containing Chloramine T, antimicrobial agent); and Experimental 2 (containing Zonyl, detergent). Brushing was performed in a toothbrushing machine (Pepsodent) with a soft brush and a suspension of toothpaste and distilled water for 300 minutes, representing 6 years of brushing. Weight was measured initially and after the trial period; roughness was measured after the trial period only. The results of roughness and weight loss were analyzed using ANOVA and Tukey tests at 5%. Results: The negative control (2.82 +/- 4.41 mg) showed the lowest weight loss. Experimental 1 (13.62 +/- 4.29 mg) and Experimental 2 (15.4 +/- 5.80 mg) were equal statistically, and Sorriso (23.22 +/- 7.23 mg) and Corega (28.83 +/- 6.34 mg) produced the greatest weight loss. Concerning roughness, the negative control group (0.03 +/- 0.01 mu m) showed the lowest value. No significant differences were found between Corega (13.43 +/- 1.65 mu m), Experimental 1 (12.28 +/- 0.85 mu m), and Experimental 2 (10.68 +/- 2.56 mu m). The Sorriso toothpaste produced the greatest amount of surface roughness (19.15 +/- 2.36 mu m). Conclusion: Of the tested dentifrices, the experimental preparations proved to be the least abrasive and resulted in the lowest weight loss after brushing of the acrylic. Based on these findings, the use of these experimental dentifrices is advocated. Further evaluation based on the ability of these preparations to remove biofilms is required.

Effects of Ethanol on the Surface and Bulk Properties of a Microwave-Processed PMMA Denture Base Resin

Purpose: This study evaluated the effect of different concentrations of ethanol on hardness, roughness, flexural strength, and color stability of a denture base material using a microwave-processed acrylic resin as a model system. Materials and Methods: Sixty circular (14 x 4 mm) and 60 rectangular microwave-polymerized acrylic resin specimens (65 x 10 x 3 mm(3)) were employed in this study. The sample was divided into six groups according to the ethanol concentrations used in the immersion solution, as follows: 0% (water), 4.5%, 10%, 19%, 42%, and 100%. The specimens remained immersed for 30 days at 37 degrees C. The hardness test was performed by a hardness tester equipped with a Vickers diamond penetrator, and a surface roughness tester was used to measure the surface roughness of the specimens. Flexural strength testing was carried out on a universal testing machine. Color alterations (Delta E) were measured by a portable spectrophotometer after 12 and 30 days. Variables were analyzed by ANOVA/Tukey`s test (alpha = 0.05). Results: For the range of ethanol-water solutions for immersion (water only, 4.5%, 10%, 19.5%, 42%, and 100%), the following results were obtained for hardness (13.9 +/- 2.0, 12.1 +/- 0.7, 12.9 +/- 0.9, 11.2 +/- 1.5, 5.7 +/- 0.3, 2.7 +/- 0.5 VHN), roughness (0.13 +/- 0.01, 0.15 +/- 0.07, 0.13 +/- 0.05, 0.13 +/- 0.02, 0.23 +/- 0.05, 0.41 +/- 0.19 mu m), flexural strength (90 +/- 12, 103 +/- 18, 107 +/- 16, 90 +/- 25, 86 +/- 22, 8 +/- 2 MPa), and color (0.8 +/- 0.6, 0.8 +/- 0.3, 0.7 +/- 0.4, 0.9 +/- 0.3, 1.3 +/- 0.3, 3.9 +/- 1.5 Delta E) after 30 days. Conclusions: The findings of this study showed that the ethanol concentrations of tested drinks affect the physical properties of the investigated acrylic resin. An obvious plasticizing effect was found, which could lead to a lower in vivo durability associated with alcohol consumption.

Physical Properties of an Acrylic Resin after Incorporation of an Antimicrobial Monomer

Purpose: This study evaluated the effect of the incorporation of the antimicrobial monomer methacryloyloxyundecylpyridinium bromide (MUPB) on the hardness, roughness, flexural strength, and color stability of a denture base material. Materials and Methods: Ninety-six disk-shaped (14-mm diameter x 4-mm thick) and 30 rectangular (65 x 10 x 3.3 mm(3)) heat-polymerized acrylic resin specimens were divided into three groups according to the concentration of MUPB (w/w): (A) 0%, (B) 0.3%, (C) 0.6%. Hardness was assessed by a hardness tester equipped with a Vickers diamond penetrator. Flexural strength and surface roughness were tested on a universal testing machine and a surface roughness tester, respectively. Color alterations (Delta E) were measured by a portable spectrophotometer after 12 and 36 days of immersion in water, coffee, or wine. Variables were analyzed by ANOVA/Tukey HSD test (alpha = 0.05). Results: The following mean results (+/-SD) were obtained for hardness (A: 15.6 +/- 0.6, B: 14.6 +/- 1.7, C: 14.8 +/- 0.8 VHN; ANOVA: p = 0.061), flexural strength (A: 111 +/- 17, B: 105 +/- 12, C: 88 +/- 12 MPa; ANOVA: p = 0.008), and roughness (A: 0.20 +/- 0.11, B: 0.20 +/- 0.11, C: 0.24 +/- 0.08 mu m; ANOVA: p = 0.829). Color changes of immersed specimens were significantly influenced by solutions and time (A: 9.1 +/- 3.1, B: 14.8 +/- 7.5, C: 13.3 +/- 6.1 Delta E; ANOVA: p < 0.05). Conclusions: The incorporation of MUPB affects the mechanical properties of a denture base acrylic resin; however, the only significant change was observed for flexural strength and may not be critical. Color changes were slightly higher when resin containing MUPB was immersed in wine for a prolonged time; however, the difference has debatable clinical relevance.

The Effect of Polymerization Cycles on Color Stability of Microwave-Processed Denture Base Resin

Purpose: This study evaluated the effect of different microwave polymerization cycles on the color changes of a microwave-processed denture base resin after accelerated aging and immersion in beverages. Materials and Methods: Specimens of light pink acrylic resin were divided into three groups according to polymerization cycle: (A) 500 W for 3 minutes, (B) 90 W for 13 minutes + 500 W for 90 seconds, and (C) 320 W for 3 minutes + 0 W for 4 minutes + 720 W for 3 minutes. Control groups were a heat-processed acrylic resin (T) and a chemically activated denture repair resin (Q). Eight specimens per group were aged in an artificial aging chamber and evaluated at 20, 192, and 384 hours. Another series of 40 specimens per group were immersed in water, coffee, tea, cola, or red wine and evaluated at 1, 12, and 36 days. Color was measured by a spectrophotometer before and after aging or immersion. Color changes (Delta E) were analyzed by ANOVA/Bonferroni t-test (alpha = 0.05). Results: Mean Delta E (+/- SD) after 384 hours of accelerated aging were (A) 2.51 +/- 0.50; (B) 3.16 +/- 1.09; (C) 2.89 +/- 1.06; (T) 2.64 +/- 0.34; and (Q) 9.03 +/- 0.40. Group Q had a significantly higher Delta E than the other groups. Color changes of immersed specimens were significantly influenced by solutions and time, but the five groups showed similar values. Mean Delta E at 36 days were (water) 1.4 +/- 0.8; (coffee) 1.3 +/- 0.6; (tea) 1.7 +/- 0.5; (cola) 1.4 +/- 0.7; and (red wine) 10.2 +/- 2.7. Results were similar among the five test groups. Conclusions: Color changes of the microwave-polymerized denture base resin tested were not affected by different polymerization cycles after accelerated aging or immersion in beverages. These changes were similar to the conventional heat-polymerized acrylic resin test, but lower than the repair resin after accelerated aging.

Effect of methyl methacrylate monomer on bond strength of denture base resin to acrylic teeth

Bond failures at the acrylic teeth and denture base resin interface are still a common clinical problem in prosthodontics. The effect of methyl methacrylate (MMA) monomer on the bond strength of three types of denture base resins (Acron MC, Lucitone 550 and QC-20) to two types of acrylic teeth (Biotone and Trilux) was evaluated. Twenty specimens were produced for each denture base resin/acrylic tooth combination and were randomly divided into control (acrylic teeth received no surface treatment) and experimental groups (MMA was applied to the surface of the acrylic teeth for 180 s) and were submitted to shear tests (1 mm/mm). Data (MPa) were analyzed using three-way ANOVA/Student`s test (alpha = 0.05). MMA increased the bond strength of Lucitone denture base resins and decreased the bond strength of QC-20. No difference was detected for the bond strength of Acron MC base resin after treatment with MMA. (C) 2008 Elsevier Ltd. All rights reserved.

Developing biodegradable mulch films from starch-based polymers

This paper examines the development of starch-based plastics for use as biodegradable mulch film. A variety of starch-based polymers are blended with high performance biodegradable polyester polymers in order to determine the applicability of films to be processed on a film blowing line and to perform well in mulch film field trials. The process of material formulation, film blowing processing and scale-up and performance properties are highlighted for a successful material. Insights into future developments of starch-derived biodegradable polymers are given.

Pulpal heat changes with newly developed resin photopolymerisation systems

Composite resin is a widely-used direct tooth coloured restorative material. Photoactivation of the polymerisation reaction can be achieved by visible blue light from a range of light sources, including halogen lamps, metal halide lamps, plasma arc lamps, and Light Emitting Diode (LED) lights. Concerns have been raised that curing lights may induce a temperature rise that could be detrimental to the vitality of the dental pulp during the act of photoactivation. The present study examined heat changes associated with standardised class V restorations on the buccal surface of extracted premolar teeth, using a curing time of 40 seconds. The independent effects of type of light source, resin shade and remaining tooth thickness were assessed using a matrix experimental design. When a conventional halogen lamp, a metal halide lamp and two different LED lights were compared, it was found that both LED lamps elicited minimal thermal changes at the level of the dental pulp, whereas the halogen lamp induced greater changes and the metal halide lamp caused the greatest thermal insult of all the light sources. These thermal changes were influenced by resin shade, with different patterns for LED versus halogen or halide sources. Thermal stress reduced as the remaining thickness of tooth structure between the pulp and the cavity floor increased. From these results, it is concluded that LED lights produce the least thermal insult during photopolymerisation of composite resins.

Towards synthetic vaccines built on carbohydrate cores

Lipophilic polyfunctional carbohydrate core/templates have been designed and developed for drug/vaccine delivery. Three carbohydrate-based templates containing four protected N-terminal arms were synthesised from glucose and galactose. Methyl alpha-D-glucopyranoside was converted to two derivatives bearing a carboxylic acid handle for attachment to solid supports, spacer arms of differing hydrophilicity, and phthaloyl-protected amino groups suitable for peptide chain extension. beta-D-Galactopyranosyl azide was converted to a template bearing a carboxylic acid handle and four BOC-protected amines. All the templates were found to be suitable for attachment to solid supports and subsequent cleavage from resins, using either BOC- or FMOC-methodologies.

Preparation and characterisation of biodegradable starch-based nanocomposite materials

Different formulations of biodegradable starch-polyester blend nanocomposite materials have been film blown on a pilot scale film blowing tower. The physical properties of different films have been examined by thermal and mechanical analysis and X-ray diffraction. The results show that the addition of an organoclay (from 0 to 5 wt%) significantly improves both the processing and tensile properties over the original starch blends. Wide angle X-ray diffraction (WAXD) results indicate that the best results were obtained for 30wt% starch blends, and the level of delamination depends on the ratio of starch to polyester and amount of organoclay added. The crystallisation temperature of the nanocomposite blends is significantly lower than the base blend. This is probably due to the platelets inhibiting order, and hence crystallisation, of the starch and polyester. The mechanical and thermal properties of the blends are also sensitive to the way the clay particles are dispersed. (C) 2003 Society of Chemical Industry.

Genotoxicity biomarkers in occupational to formaldehyde in pathology anatomy laboratories

Formaldehyde (FA) the most simple and reactive of all aldehydes, is a colorless, reactive and readily polymerizing gas at normal temperature. It has a pungent, suffocating odour that is recognized by most human subjects at concentrations below 1ppm. According to the Report on Carcinogens, FA ranks 25th in the overall U.S. chemical production with more than 11 billion pounds (5 million tons) produced each year. Is an important industrial compound that is used in the manufacture of synthetic resins and chemical compounds such as lubricants and adhesives. It has also applications as a disinfectant, preservative and is used in cosmetics. Estimates of the number of persons who are occupationally exposed to FA indicate that, at least at low levels, may occur in a wide variety of industries. The occupational settings with most extensive use of formaldehyde is in the production of resins and in anatomy and pathology laboratories. Several studies reported a carcinogenic effect in humans after inhalation of FA, in particular an increased risk for nasopharyngeal cancer. Nowadays, the International Agency for Research on Cancer (IARC) classifies FA as carcinogenic to humans (group 1), on the basis of sufficient evidence in humans and sufficient evidence in experimental animals. Manifold in vitro studies clearly indicated that FA is genotoxic. FA induced various genotoxic effects in proliferatin cultured mammalian cells. A variety of evidence suggests that the primary DNA alterations after FA exposure are DNA-protein crosslinks. Incomplete repair of DPX can lead to the formation of mutations.

Occupational exposure to formaldehyde: effects of years of exposure in the frequency of micronucleus

Formaldehyde: an important industrial compound used in the manufacture of synthetic resins and chemical compounds such as lubricants and adhesives; also applied as a disinfectant, preservative and in cosmetics productions; relevant workplace exposure to FA also occurs in anatomy, pathology and in mortuaries; classified by IARC as carcinogenic to humans (Group 1), based on sufficient evidence in humans and experimental animals; manifold in vitro studies indicated that FA can induce genotoxic effects in proliferating cultured mammalian cells. Aim of the study: to evaluate if years of exposure induced a genotoxic biomarkers increase, namely MN in lymphocytes and buccal cells, in workers occupationally exposed to FA (factory and pathology anatomy laboratory).

Micronuclei in peripheral blood lymphocytes in formaldehyde occupationally exposed workers

Formaldehyde (CH2O) the most simple and reactive of all aldehydes, is a colorless, reactive and readily polymerizing gas at normal temperature. It has a pungent, suffocating odour that is recognized by most human subjects at concentrations below 1 ppm. According to the Report on Carcinogens, formaldehyde (FA) ranks 25th in the overall U.S. chemical production with more than 11 billion pounds (5 million tons) produced each year. Is an important industrial compound that is used in the manufacture of synthetic resins and chemical compounds such as lubricants and adhesives. It has also applications as a disinfectant, preservative and is used in cosmetics. Estimates of the number of persons who are occupationally exposed to FA indicate that, at least at low levels, may occur in a wide variety of industries. The occupational settings with most extensive use of formaldehyde is in the production of resins and in anatomy and pathology laboratories. Several studies reported a carcinogenic effect in humans after inhalation of FA, in particular an increased risk for nasopharyngeal cancer. Nowadays, the International Agency for Research on Cancer (IARC) classifies FA as carcinogenic to humans (group 1), on the basis of sufficient evidence in humans and sufficient evidence in experimental animals. Manifold in vitro studies clearly indicated that FA is genotoxic. FA induced various genotoxic effects in proliferatin cultured mammalian cells. A variety of evidence suggests that the primary DNA alterations after FA exposure are DNA-protein crosslinks (DPX). Incomplete repair of DPX can lead to the formation of mutations.

Wells turbine: fiberglass flanges

A introdução desta tese começa por realizar um enquadramento do projecto em mão, apresentando a central de energia das ondas em que se encontram os componentes em fibra de vidro a projectar. Esta central usa o princípio de variação de coluna de água, e encontra-se localizada na ilha do Pico, Açores. São de seguida apresentados os objectivos deste trabalho, que consistem na selecção de materiais de fabrico dos componentes, desenvolvimento de uma metodologia para projectar juntas aparafusadas em materiais compósitos, dimensionamento e comparação de duas juntas concorrentes em materiais compósitos: junta solicitada à tracção e junta solicitada ao corte, validação da análise e estudo das causas dos vários tipos de falha destas juntas. A parte I deste trabalho é o resultado da pesquisa bibliográfica efectuada para levar a cabo os objectivos definidos. Assim, começa por se fazer uma descrição dos materiais e processos de fabrico que mais se adequam ao presente projecto, nomeadamente fibra de vidro, resinas, tecidos, impregnação manual, RTM e infusão por vácuo. Daqui resultou que os materiais mais adequados para esta aplicação são fibra de vidro do tipo E e resina polyester devido ao seu baixo custo e larga utilização em aplicações estruturais marinhas. O processo de fabrico mais eficiente é a infusão por vácuo devido á sua vocação para pequenas séries de produção, a poupança que permite em termos de mão-de-obra, a complacência com normas de emissão de voláteis e as boas propriedades das partes produzidas. No capítulo II da parte I são discutidos os tópicos relacionados com juntas em materiais compósitos. Da pesquisa levada a cabo conclui-se que as grandes vantagens das juntas aparafusadas são a sua facilidade de montagem e desmontagem, facilidade de inspecção e capacidade de ligar quaisquer tipos de materiais. Quanto à furação de compósitos é importante referir a necessidade de utilizar ferramentas resistentes e parâmetros de maquinação que minimizem o dano infligido aos laminados. Isto é possível através da selecção de ferramentas com passos baixos que reduzam igualmente a dimensão do seu centro estático responsável pela força axial exercida sobre o laminado - principal factor causador de dano. Devem-se igualmente utilizar baixas velocidades de avanço e elevadas velocidades de rotação. É importante salientar a importância da realização de pré-furação, de utilização de um prato de suporte na superfície de saída do laminado e a existência de ferramentas especialmente concebidas para a furação de compósitos. Para detectar e quantificar o dano existente num furo destacam-se os métodos de inspecção ultrasónica e a radiografia. Quanto aos parâmetros que influenciaram o comportamento de juntas aparafusadas destacam-se os rácios largura/diâmetro, distância ao bordo/diâmetro, espessura/diâmetro, pré-tensão, fricção, sequência de empilhamento e respectivas proporções, dimensão das anilhas e folga entre o parafuso e o furo. A pesquisa efectuada visando metodologias de projecto fiáveis ditou a necessidade de utilizar métodos que permitiram determinar o parafuso mais carregado de uma junta, efectuar o cálculo de tensões no mesmo, e ainda métodos que permitam determinar a primeira falha que ocorre no laminado bem como a falha final no mesmo. O capítulo III da primeira parte descreve os métodos de análise de tensões necessários para as metodologias de projecto utilizadas. Aqui é apresentada a teoria clássica da laminação, um método para determinação do parafuso mais carregado, um método analítico baseado na teoria da elasticidade anisotrópica de um corpo e o método dos elementos finitos. O método para determinar o parafuso mais carregado - análise global - consiste num modelo bidimensional de elementos finitos em que 2 laminados coincidentes são modelados com elementos lineares de casca com 4 nós, sendo a extremidade de um laminado restringida em todos os graus de liberdade e a extremidade oposta do segundo laminado carregada com a carga pretendida. Os laminados são ligados através de elementos mola que simulam os parafusos, sendo a sua constante de rigidez previamente calculada para este fim. O método analítico modela o contacto assumindo uma distribuição de pressão cosinoidal ao longo de metade do furo, e é válido para laminados simétricos e quasi-isotrópicos. O método dos elementos finitos é o que mais factores permite ter em conta, sendo os modelos tridimensionais com um elemento por camada os que melhor modelam o estado de tensões experienciado por uma junta aparafusada em materiais compósitos. O tópico de análise de falha é abordado no capítulo 4 da primeira parte. Aqui são apresentados os resultados do world wide failure exercice que compara vários critérios de falha existentes até 2004, fazendo-se referência a desenvolvimentos recentes que têm ocorrido nesta área. O critério de Puck surge como aquele que permite previsões de falha mais exactas. O critério de falha de Hashin 3D foi o escolhido para o presente trabalho, devido à sua facilidade de implementação num modelo de elementos finitos, à sua capacidade para detectar modos de falha subcríticos e à sua utilização em trabalhos anteriores que apresentaram previsões de falha muito próximas dos dados experimentais. Também neste capítulo se apresentaram os vários tipos de falha de uma junta aparafusada em materiais compósitos, apresentando as causas de cada uma. Por fim, na última secção, apresenta-se o método de dano progressivo que se desenvolveu para prever a primeira falha final do laminado. Este é muito interessante tendo permitido previsões de falha muito próximas dos resultados experimentais em trabalhos anteriores. Este método é iterativo e encontra-se dividido em 3 passos: Análise de tensões, análise de falha utilizando o critério de Hashin 3D e degradação de propriedades, de acordo com o tipo de falha detectada. Para além dos passos referidos, existe ainda um quarto responsável pelo fim da análise que consiste na aferição da existência ou não de falha final e respectivo tipo de falha (por pressão de contacto, por tensão ou por esforços de corte). No capítulo V da primeira parte é apresentado o resultado de uma pesquisa das normas de teste necessárias para obter as propriedades dos materiais requeridas para a aplicação dos métodos descritos neste trabalho. A parte II deste trabalho consiste na aplicação dos métodos apresentados na parte I ao caso concreto em estudo. Os softwares Microsoft Excel, Matlab e ANSYS foram utilizados para este fim. A junta começa por ser dimensionada estimando a espessura necessária do componente e o número e características dos parafusos. De seguida foi feita uma análise global à flange em estudo determinando a força suportada pelo parafuso mais carregado. Após esta análise desenvolveu-se um modelo tridimensional de elementos finitos da zona em que se encontra o parafuso mais carregado, utilizando elementos sólidos lineares e isoparamétricos de 8 nós e uma malha gerada pelo método directo. Aplicou-se a este modelo o algoritmo de dano progressivo descrito na primeira parte. Começou por se incluir explicitamente o parafuso, anilhas, pré-tensão e a modelação dos vários contactos com fricção posteriormente simplificado o modelo restringindo radialmente os nós da porção carregada do furo, excluindo os factores mencionados inicialmente. Procurou-se validar o modelo utilizando o método de cálculo de tensões descrito na primeira parte, desenvolvendo um programa em Matlab para o efeito. Tal não foi possível tendo-se incluído a tentativa realizada em anexo. Para efeitos de dimensionamento, desenvolveu-se um modelo de elementos finitos de duas dimensões da junta em causa, utilizando elementos de casca lineares de quatro nós isoparamétricos com uma espessura unitária. Através da análise de tensões efectuada com este modelo, e utilizando um método combinado programado em linguagem paramétrica, foi possível dimensionar as duas juntas concorrentes pretendidas. Este método combinado consistiu no cálculo de tensões em pontos localizados sobre uma curva característica e utilização de um critério de falha quadrático para cálculo da espessura necessária para a junta. O dimensionamento ditou que a junta solicitada à tensão necessita de pelo menos 127% das camadas e do custo de uma junta solicitada ao corte equivalente.

Caracterização da exposição e eventuais efeitos para a saúde da exposição profissional ao estireno nos ortoprotésicos

Mestrado em Segurança e Higiene do Trabalho.