Effect of coagulants on the fouling and performance of ultrafiltration (UF) membranes

The combined coagulation and ultrafiltration (UF) system (C-UF system) is an advanced technology to treat natural organic matter (NOM) present in water. Traditional coagulants — prehydrolyzed inorganic coagulants, organic coagulants and composite coagulants were chosen to treat synthetic water containing humic acid (HA) in order to find an efficient coagulant that could remove NOM from the water effectively. The fouling, removal efficiency of UF and the chlorine decay in the permeate were used to evaluate the effectiveness of the coagulants. The initial UV254 absorption of the tested water samples were from 0.208 to 0.234, and the UV254 after coagulation was from 0.05 to 0.184. The UV254 did not increase after coagulation. Since the humic acid used was soluble, the initial turbidity of the tested water samples were very close to zero. The turbidity increased after coagulation, as the coagulants react with humic acid to form micro-flocs, which cannot be removed fully by sedimentation. The results showed that polyferric chloride could not remove humic acid efficiently during coagulation process, but removed the humic acid well when used in the C-UF system. Moreover, for polyferric chloride and UF system, the concentration of organic compounds in permeates were minimal indicating very low levels of disinfection by-product formation, if chlorinated.

Effect of operating parameters and cleaning on the performance of ceramic membranes treating partially clarified sugar cane juice

The performance of ceramic membranes with pore sizes of 0.05 and 0.10 mm in purifying limed and partially clarified sugar cane juice was investigated under different operating conditions. From various operating conditions and strategies, switching off the permeate for 5 seconds for every 5 minutes (S5sT5 m) by an automated control valve provided higher flux. From the three pH experiments conducted on the 0.05 mm membrane, the best performance was observed at a pH of 7.5. Amongst the four fouling models tested, the cake filtration model fitted the performance of both membranes with higher accuracy at a transmembrane pressure of 0.5 bar. Filtering the cane juice through the membrane reduced the turbidity by 99.7%, color by 15%, and the starch concentration by 80% as well as increased the purity by 1.4%. The effective cleaning chemical composition from experimental results showed that 1% NaOH and 3000 ppm NaOCl solution performed the best but only for the experiments that were treating limed and partially clarified juice at pH 7.5.

Performance evaluation of different ultrafiltration membranes for the reclamation and reuse of secondary effluent

This study investigates and compares the performance of two different types of ultrafiltration (UF) membranes in the recovery of water from secondary treated wastewater. Filtration experiments were carried out on a pilot scale cross-flow unit using synthetic wastewater similar to the quality of secondary treated wastewater by varying the operating parameters such as transmembrane pressure (TMP), feed composition and membrane configuration. The filtration experiments demonstrated that the flux recovery through spiral polymeric UF membrane was more sensitive to the variation in TMP compared to the tubular ceramic UF membrane over the range of TMP studied. The resistance in series model was used for the evaluation of the resistance to the permeate flux. The fouling resistance, particularly irreversible resistance compared to reversible resistance plays a major role in the total resistance for the tubular ceramic membrane. In contrast clean membrane resistance is the major contributor for the total resistance of the spiral polymeric membrane. Finally, the effectiveness of the filtration treatment was determined by evaluating the rejection coefficients for various pollution indices of the wastewater. Significant differences in the performance of the membrane types were observed which are likely to impact on the selection, operation and maintenance of the membrane system.

Diatoms : self assembled silica nanostructures, and templates for bio/chemical sensors and biomimetic membranes

In this review we highlight recent advances in the understanding of biosilica production, biomodification of diatom frustules and their subsequent applications in bio/chemical sensors, and as a model membrane for filtration and separation.

Drug release rate and anti-microbial effect of controlled-diffusion biopolymer membranes

In this study, a series of fibrous membranes made from cellulose acetate (CA) and polyester urethane (PEU) by co-electrospining or blend-electrospining were evaluated for drug release kinetics, in vitro anti-microbial activity and in vivo would healing performance when used as wound dressings. To stop common clinical infections, an antibacterial agent, Polyhexamethylene Biguanide (PHMB) was incorporated into e-spun fibres. The presence of CA in the wound healing membrane was found to improve hydrophilicity and permeability to air and moisture. The in vivo tests indicated that the addition of PHMB and CA considerably improved the wound healing efficiency. CA fibres became slightly swollen upon contacting with the wound exudates. It can not only speed up the liquid evaporation but also create a moisture environment for wound recovery. The drug release dynamics of membranes was controlled by the structure of membranes and component rations within membranes. The lower ration of CA:PEU retained the sound mechanical properties of membranes, and also reduced the boost release effectively and slowed down diffusion of antibacterial agent during in vitro tests. The controlled-diffusion membranes exert long-term anti-infective effect.

Electrospinning of continuous nanofiber bundles and twisted nanofiber yarns

Spinning is a prehistoric technology in which endless filaments, shorter fibers or twisted fibers are put together to produce yarns that serve as key element to assemble multifarious structural designs for diverse functions. Electrospinning has been regarded as the most effective and versatile technology to produce nanofibers with controlled fiber morphology, dimension and functional components from various polymeric materials (Dersch et al., 2007, Frenot and Chronakis, 2003, Schreuder-Gibson et al., 2002). However, most electrospun fibers are produced in the form of randomly-oriented nonwoven fiber mats (Doshi and Reneker, 1995, Madhavamoorthi, 2005). The relatively low mechanical strength and difficulty in tailoring the fibrous structure have restricted their applications. With the rapid development in nanoscience and nanotechnology, yarns composed of nanofibers may uncover new opportunities for development of well-defined three dimensional nano fibrous architectures. This chapter focuses on recent research and advancement in electrospinning of nanofiber bundles and nanofiber yarns. The preparation, morphology, mechanical properties and potential applications of these fibrous materials are discussed in details.

Toughening of a carbon-fibre composite using electrospun poly(Hydroxyether of Bisphenol A) nanofibrous membranes through inverse phase separation and inter-domain etherification

The interlaminar toughening of a carbon fibre reinforced composite by interleaving a thin layer (~20 microns) of poly(hydroxyether of bisphenol A) (phenoxy) nanofibres was explored in this work. Nanofibres, free of defect and averaging several hundred nanometres, were produced by electrospinning directly onto a pre-impregnated carbon fibre material (Toray G83C) at various concentrations between 0.5 wt % and 2 wt %. During curing at 150 °C, phenoxy diffuses through the epoxy resin to form a semi interpenetrating network with an inverse phase type of morphology where the epoxy became the co-continuous phase with a nodular morphology. This type of morphology improved the fracture toughness in mode I (opening failure) and mode II (in-plane shear failure) by up to 150% and 30%, respectively. Interlaminar shear stress test results showed that the interleaving did not negatively affect the effective in-plane strength of the composites. Furthermore, there was some evidence from DMTA and FT-IR analysis to suggest that inter-domain etherification between the residual epoxide groups with the pendant hydroxyl groups of the phenoxy occurred, also leading to an increase in glass transition temperature (~7.5 °C).

Transport properties of multi-layer fabric based on electrospun nanofiber mats as a breathable barrier textile material

Layered fabric systems with an electrospun nanofiber web layered onto a sandwich of woven fabric were developed toexamine the feasibility of developing breathable barrier textile materials. Some parameters of nanofiber mats, including thetime of electrospinning and the polymer solution concentration, were designed to change and barrier properties ofspecimens were compared. Air permeability, water vapor transmission, and water repellency (Bundesmann and hydrostaticpressure tests) were assessed as indications of comfort and barrier performance of different samples. These performancesof layered nanofiber fabrics were compared with a well-known water repellent breathable multi-layered fabric(Gortex).Multi-layered electrospun nanofiber mats equipped fabric (MENMEF) showed better performance in windproof propertythan Gortex fabric. Also, water vapor permeability of MENMEF was in a range of normal woven sport and work clothing.Comparisons of barrier properties of MENMEF and the currently available PTFE coated materials showed that, thoseproperties could be achieved by layered fabric systems with electrospun nanofiber mats.

Effect of cellulose nanofiber dimensions on sheet forming through filtration

Four different cellulose nanofibers samples were prepared from northern bleached softwood kraft fibers. Fiber diameter distributions were measured from SEM images. Fiber aspect ratios ranging from 84 to 146 were estimated from fiber suspension sedimentation measurements. Three samples had heterogeneous distributions of fiber diameters, while one sample was more homogeneous. Sheet forming experiments using filters with pores ranging from 150 to 5 μm showed that the samples with a heterogeneous distribution of fiber dimensions could be easily formed into sheets at 0. 2% initial solids concentration with all filter openings. On the other hand, sheets could only be formed from the homogenous sample by using 0. 5% or more initial solids content and a lower applied vacuum and smaller filter openings. The forming data and estimated aspect ratios show reasonable agreement with the predictions of the crowding number and percolation theories for the connectivity and rigidity thresholds for fiber suspensions.