Mudanças químicas e fitodisponibilidade de zinco estimada por método isotópico, em solo tratado com lodo de esgoto

Zn availability in Red Latossol (Rhodic Ferralsol) of different pH amended with different rates of sewage sludge was studied by the isotopic 65Zn L value method. Soil chemical properties were found to be altered by SS addition. Zn concentration and Zn derived from SS (ZnpfSS) in plant, and Zn phytoavailability (L value), were increased with increasing SS rates. The linear correlation coefficient of plant Zn with SS rates and with L value was significant at 1% probability. The L value proved an efficient method for predicting Zn phytoavailability in sewage sludge-amended soil with different pH under the soil conditions studied.

Lodo de esgoto como fonte de nitrogênio: concentração no perfil do solo e em plantas de milho

O objetivo deste trabalho foi avaliar a concentração de nitrogênio em plantas de milho e ao longo do perfil de um Latossolo Vermelho eutroférrico submetido a doses de lodo de esgoto e fertilizante mineral. O experimento foi instalado em delineamento experimental em blocos casualizados com 4 tratamentos (0,0; 55,0; 110,0 e 167,5 Mg.ha-1 de lodo de esgoto em doses acumuladas) e 5 repetições para um período de avaliação de 1 ano. A amostragem de solo foi realizada aos 60 dias após a emergência (d.a.e.) das plantas nas profundidades 0,0-0,1, 0,1-0,2, 0,2-0,4, 0,4-0,6, 0,6-0,8 e 0,8-1,0 m. Também aos 60, 80 e 128 d.a.e. foram coletadas, respectivamente, folha diagnose, planta inteira e grão. As maiores doses de lodo de esgoto proporcionaram maiores quantidades de nitrogênio no solo. O nitrogênio do solo, após a profundidade de 0,6 m, não diferiu entre as camadas avaliadas. Quanto maior a dose de lodo de esgoto, menor a proporção de nitrogênio em profundidade.

Produção de milho adubado residualmente com composto de lodo de esgoto e fosfato de Gafsa

Objetivou-se, com este trabalho, avaliar o efeito residual da adubação com composto de lodo de esgoto e fosfato natural de Gafsa sobre os teores de nutrientes no solo, na planta e na produtividade do milho. O trabalho foi realizado em Cambissolo Háplico. Os tratamentos, em esquema fatorial 2 x 4, corresponderam a 2 doses de fosfato de Gafsa (0 e 90 kg ha-1 de P2O5) e 4 doses de composto de lodo de esgoto (0; 25; 50 e 75 t ha-1, em base seca). O delineamento experimental utilizado foi em blocos casualizados, com 3 repetições. Em geral, a produtividade e os teores de nutrientes no solo e na planta no segundo cultivo sucessivo de milho não foram influenciados pela adubação com fosfato natural reativo. Entretanto, a produtividade de milho e os teores de nutrientes no solo e nas folhas de milho aumentaram com a dose de composto de lodo de esgoto ao solo, sendo a dose de 75 Mg ha-1, a de maior efeito residual. A produtividade do milho é menor no segundo cultivo sucessivo em razão do empobrecimento do solo em fósforo e potássio, recomendando-se novas adubações com lodo de esgoto, a cada cultivo realizado.

Fertilidade do solo, estado nutricional e produtividade de girassol, em função da aplicação de lodo de esgoto

O lodo de esgoto é um resíduo urbano-industrial que tem causado preocupação, quanto ao uso agrícola. Sua utilização pode ser viável, após a devida suplementação potássica, em substituição a fertilizantes minerais, especialmente em culturas como a do girassol. O presente trabalho objetivou avaliar a produtividade e nutrição mineral do girassol cv. CATISSOL 01, além da fertilidade de um Latossolo Vermelho eutroférrico adubado com lodo de esgoto, em comparação à adubação mineral, por dois anos consecutivos. O experimento utilizou delineamento em blocos casualizados, com 4 tratamentos (fertilização mineral, 5 t ha-1 ano-1, 10 t ha-1 ano-1 e 20 t ha-1 ano-1 de lodo de esgoto) e 5 repetições. Foram analisadas a produtividade de grãos de girassol, a concentração de macro e micronutrientes na folha diagnóstico e a fertilidade do solo. A produtividade de sementes do girassol adubado com o resíduo, em todas as doses, foi equivalente à adubação mineral, e os teores foliares situaram-se na faixa adequada, tanto para macro quanto para micronutrientes. O uso de lodo de esgoto, com suplementação potássica, mostrou-se eficiente na substituição total ou parcial da adubação mineral, sem prejudicar a produtividade da cultura do girassol.

Phytostabilisation : use of wetland plants to treat mine tailings

Mine tailings can be rich in sulphide minerals and may form acid mine drainage (AMD) through reaction with atmospheric oxygen and water. AMD contains elevated levels of metals and arsenic (As) that could be harmful to animals and plants. An oxygen-consuming layer of organic material and plants on top of water-covered tailings would probably reduce oxygen penetration into the tailings and thus reduce the formation of AMD. However, wetland plants have the ability to release oxygen through the roots and could thereby increase the solubility of metals and As. These elements are released into the drainage water, taken up and accumulated in the plant roots, or translocated to the shoots. The aim was to examine the effects of plant establishment on water-covered mine tailings by answering following questions: A) Is plant establishment on water-covered mine tailings possible? B) What are the metal and As uptake and translocation properties of these plants? C) How do plants affect metal and As release from mine tailings, and which are the mechanisms involved? Carex rostrata Stokes, Eriophorum angustifolium Honck., E. scheuchzeri Hoppe, Phragmites australis (Cav.) Steud., Salix phylicifolia L. and S. borealis Fr. were used as test plants. Influences of plants on the release of As, Cd, Cu, Pb, Zn and in some cases Fe in the drainage water, and plant element uptake were studied in greenhouse experiments and in the field. The results obtained demonstrate that plant establishment are possible on water-covered unweathered mine tailings, and a suitable amendment was found to be sewage sludge. On acidic, weathered tailings, a pH increasing substance such as ashes should be added to improve plant establishment. The metal and As concentrations of the plant tissue were found to be generally higher in roots than in shoots. The uptake was dependent on the metal and As concentrations of the tailings and the release of organic acids from plant roots may have influenced the uptake. The metal release from tailings into the drainage water caused by E. angustifolium was found to depend greatly on the age and chemical properties of the tailings. However, no effects of E. angustifolium on As release was found. Water from old sulphide-, metal- and As-rich tailings with low buffering capacity were positively affected by E. angustifolium by causing higher pH and lower metal concentrations. In tailings with relatively low sulphide, metal and As contents combined with a low buffering capacity, plants had the opposite impact, i.e. a reduction in pH and elevated metal levels of the drainage water. The total release of metal and As from the tailings, i.e. drainage water together with the contents in shoots and roots, was found to be similar for C. rostrata, E. angustifolium and P. australis, except for Fe and As, where the release was highest for P. australis. The differences in metal and As release from mine tailings were mainly found to be due to the release of O2 from the roots, which changes the redox potential. Release of organic acids from the roots slightly decreased the pH, although did not have any particular influence on the release of metal and As. In conclusion, as shown here, phytostabilisation may be a successful technique for remediation of mine tailings with high element and sulphide levels, and low buffering capacity.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Spurenanalyse von Uran und Plutonium sowie Speziationsuntersuchungen an Plutonium mit massenspektrometrischen und kapillarelektrophoretischen Methoden

Die Elemente Uran und Plutonium besitzen seit Entdeckung der Kernspaltung und der technischen Nutzung der Kernenergie eine globale Bedeutung. So trägt Pu hauptsächlich zur Radiotoxizität von abgebrannten Brennelementen bei und erfordert im Falle einer Endlagerung in einer tiefen geologischen Formation einen sicheren Verschluss für bis zu einer Million Jahre. Das Wissen über die vorliegenden chemischen Spezies ist dabei entscheidend für das Verständnis der chemisch-physikalischen Wechselwirkungen im jeweiligen geochemischen System, insbesondere mit dem Wirtsgestein (hier Ton) und den allgegenwärtigen Huminstoffen (hier Fulvinsäure). Längerfristig sind so Vorhersagen über einen Transport des hochradioaktiven Abfalls nach Auslaugung und Austritt aus einem Endlager bis in die Biosphäre möglich. Gerade der Ultraspurenbereich, im Fernfeld eines Endlagers zu erwarten, ist dabei von besonderem Interesse. Darüber hinaus machen nuklearforensische Untersuchungen – in Hinblick auf illegal benutztes Nuklearmaterial, Schmuggel oder Nuklearterrorismus – zur Bestimmung der Herkunft, des Alters oder der Radiotoxizität isotopenselektive Nachweismethoden im Ultraspurenbereich notwendig. Im Rahmen dieser Arbeit wurden hierfür die Resonanzionisationsmassenspektrometrie (RIMS) zur isotopenselektiven Spuren- und Ultraspurenanalyse von U und Pu sowie die Kapillarelektrophorese (CE) gekoppelt an die induktiv gekoppelte Plasma (ICP)-Massenspektrometrie (CE-ICP-MS) zur Speziation von Pu eingesetzt. Für den isotopenselektiven Nachweis von Ultraspurenmengen von Uran mittels RIMS wurden vorbereitende Studien durchgeführt und mehrere zweifach resonante Anregungsleitern mit nicht-resonanter Ionisation untersucht. Eine Effizienz von ca. 10^-10 bei einer Nachweisgrenze von 10^12 Atomen U-238 konnte erzielt werden. In Zusammenarbeit mit dem Institut für Radiochemie, TU München, wurde mittels RIMS die Isotopenzusammensetzung von Plutonium, abgetrennt aus einem panzerbrechenden Urangeschoss aus dem Kosovokonflikt, bestimmt und dieses als Waffenplutonium mit einem Gehalt von 15 pg Pu-239/g Uran identifiziert. Rückschlüsse über Herkunft und Alter des Plutoniums konnten daraus gewonnen werden. Für Studien zur Umweltüberwachung von Plutonium in Rheinland-Pfalz wurden Grund-, Oberflächen- und Klärwasserproben mittels RIMS untersucht. Oberhalb der Nachweisgrenze von ca. 10^7 Atomen Pu-239/500 mL konnte kein signifikanter Gehalt bestimmt werden. Zusätzlich wurden Klärschlammproben untersucht, wobei in einer Probe 5,1*10^7 Atome Pu-239/g gemessen wurde, was auf eine Anreicherung von Pu im Klärschlamm aus großen Wasservolumina hindeuten könnte. Speziationsuntersuchungen von Plutonium in Kontakt mit Fulvinsäure und dem Tonmineral Kaolinit wurden in Hinblick auf die Wechselwirkungen im Umfeld eines nuklearen Endlagers durchgeführt. Die Redoxkinetik von Pu(VI) in Kontakt mit Gorleben-Fulvinsäure zeigt eine mit steigendem pH zunehmend schnellere und vollständige Reduktion und ein vergleichbares Verhalten zur Huminsäure. Für ein Plutoniumgemisch aus allen vier umweltrelevanten Oxidationsstufen in Kontakt mit Gorleben-Fulvinsäure konnte nach ca. 1 Monat Kontaktzeit eine fasst vollständige Reduktion zum tri- und tetravalenten Pu beobachtet werden. Sorptionsuntersuchungen der stabilsten Oxidationsstufe, Pu(IV), in Kontakt mit Kaolinit bei pH = 0 bis 13 im Konzentrationsbereich 10^-7 bis 10^-9 mol/L verdeutlichen das ausgeprägte Sorptionsverhalten von Pu(IV) (ca. 60% bis 90% Sorption) im umweltrelevanten pH-Bereich bei einem Einsetzen der Sorption bei pH = 0 bis 2. Im Rahmen des "Colloid and Radionuclide Retardation" (CRR) Experiments im Felslabor Grimsel, Schweizer Alpen, wurde in Zusammenarbeit mit dem Institut für Nukleare Entsorgung, Karlsruhe, die kolloidgetragene Migration von Pu(IV) in einem Grundwasserstrom durch Scherzonen im Granitgestein unter umweltrelevanten Bedingungen untersucht. Bei Zugabe von im Grundwasser stabilen Bentonitkolloiden – Bentonit wird als ein geeignetes Verschlussmaterial für nukleare Abfälle erforscht – konnte ein erhöhter Transport des Pu(IV) beobachtet werden, der durch Sorption des Pu an die mobilen Kolloide hervorgerufen wird. Zur Speziation von Plutonium im Ultraspurenbereich wurde im Rahmen dieser Arbeit an der Entwicklung der Kopplung der CE mit der sehr sensitiven RIMS gearbeitet. Das Prinzip der offline-Kopplung basiert auf dem Sammeln der zu unterschiedlichen Zeiten am Ende der Kapillare eluierten Oxidationsstufen in einzelnen Fraktionen. Aus jeder Fraktion wird ein eigenes Filament hergestellt und mit RIMS auf seinen Plutoniumgehalt untersucht. Eine erste Validierung der Methode konnte durch Bestimmung der Oxidationsstufenzusammensetzung eines bekannten Gemischs erfolgreich für einen Gehalt von ca. 6*10^9 Atome Pu-239 durchgeführt werden. Dies stellt einen möglichen Zugang zu dem erwarteten Konzentrationsbereich im Fernfeld eines Endlagers dar.

Factors driving the carbon mineralization priming effect in a sandy loam soil amended with different types of biochar

The effect of biochar on the soil carbon mineral- ization priming effect depends on the characteristics of the raw materials, production method and pyrolysis conditions. The goal of the present study is to evaluate the impact of three different types of biochar on physicochemical properties and CO2 emissions of a sandy loam soil. For this purpose, soil was amended with three different biochars (BI, BII and BIII) at a rate of 8 wt % and soil CO2 emissions were measured for 45 days. BI is produced from a mixed wood sieving from wood chip production, BII from a mixture of paper sludge and wheat husks and BIII from sewage sludge. Cumulative CO2 emissions of biochars, soil and amended soil were well fit to a simple first-order kinetic model with correlation coef- ficients (r 2 ) greater than 0.97. Results show a negative prim- ing effect in the soil after addition of BI and a positive prim- ing effect in the case of soil amended with BII and BIII. These results can be related to different biochar properties such as carbon content, carbon aromaticity, volatile matter, fixed carbon, easily oxidized organic carbon or metal and phenolic substance content in addition to surface biochar properties. Three biochars increased the values of soil field capacity and wilting point, while effects over pH and cation exchange capacity were not observed.

Optimización de la gasificación de lodos de estaciones depuradoras de aguas residuales urbanas para minimizar la formación de alquitranes

La gasificación de lodos de depuración es una alternativa atractiva para generar gases combustibles como H2 y CO. A su vez, estos gases pueden emplearse como materias primas para la obtención de productos químicos orgánicos y combustibles líquidos. Sin embargo, la gasificación no está exenta de problemas como el ligado a la generación de residuos sólidos y alquitrán. El alquitrán en el gas puede ser un inconveniente para emplear el gas como combustible por las obstrucciones y corrosión en los equipos. Dado que las condiciones de gasificación influyen en la producción de alquitrán, este trabajo de investigación se ha centrado en analizar la influencia de parámetros como la temperatura, la carga de alimentación, el tamaño de partícula, el agente gasificante y la utilización de catalizadores en la gasificación en lecho fluidizado de lodos de depuración. Adicionalmente a la medición del efecto de los anteriores parámetros en la producción y composición del alquitrán, también se ha cuantificado su influencia en la producción y composición del gas y en producción del residuo carbonoso. Los resultados muestran que el incremento de la carga de alimentación (kg/h.m2) provoca el descenso de la producción de gas combustible y el incremento del residuo carbonoso y del alquitrán debido a la reducción del tiempo de residencia del gas lo que supone un menor tiempo disponible para las reacciones gas-gas y gas-sólido ligadas a la conversión del alquitrán y del residuo carbonoso en gases combustibles. También se ha comprobado que, el aumento del tamaño de partícula, al incrementar el tiempo de calentamiento de ésta, tiene un efecto similar en los productos de la gasificación que el derivado del incremento en la carga de alimentación. La utilización de una temperatura de gasificación alta (850 ºC), el empleo de aire-vapor como agente gasificante y/o catalizadores primarios como la dolomía consiguen reducir la producción de alquitrán. ABSTRACT Gasification of sewage sludge is an attractive alternative for generating of fuel gases such as H2 and CO. These gases, in turn, can be used as raw materials for the production of organic chemicals and liquid fuel. However, gasification is not without problems as the linked ones to production of char and tar. The tar in the gas can be an inconvenience for to use it as fuel by the problems of blockage and corrosion in the equipments. Since the gasification conditions affect the production of tar, this research has focused on analysing the influence of parameters such as temperature, throughput, the particle size, the gasifying agent and the use of catalysts in the fluidized bed gasification of sewage sludge. In addition to measuring the effect of the above parameters on the production and composition of the tar, it has also been quantified their influence on the yield and composition of the gas and char production. The results show that higher throughput (kg/h.m2) leads to a reduction of fuel gas production and an increase in the production of char and tar, this owes to a lower of gas residence time or what is the same thing less time available for gas-solid and gas-gas reactions attached to the conversion of tar and char to fuel gases. There has also been proven that the rising in particle size, by the increasing heating time of it, has a similar effect in the products of gasification that the results by the rise in the throughput. The applications a high gasification temperature (850 ° C), the use of air-steam as gasifying agent and/or dolomite as primary catalysts are able to reduce the production of tar.

Determinación de propiedades de inflamabilidad de mezclas para co-combustión

La recuperación de energía a partir de biomasa y residuos no reciclables por la combustión está cobrando una notable importancia actualmente. Una de las técnicas más utilizadas para esta propuesta es la co-combustión de mezclas de residuos y biomasa. Con esta nueva tecnología, mezclas de diferentes materiales han aparecido en las instalaciones industriales y tienen que ser reconocidas como nuevos combustibles, debido a que a sus propiedades son aún desconocidas. Estas propiedades incluyen las energéticas, que son el objetivo del proceso de mezcla, y también las propiedades de inflamabilidad. Residuos y biomasa en forma de polvos tienen propiedades de ignición que se han de tener en cuenta a la hora de diseñar las medidas de prevención y protección en una instalación industrial. El objetivo principal de este estudio es determinar el riesgo de ignición de las mezclas de residuos / biomasa en capas y cómo, mediante la adición de diferentes cantidades de estos materiales, este riesgo puede cambiar. Para desarrollar este estudio, se utiliza la temperatura mínima de ignición en la capa. Tres muestras diferentes han sido analizadas, lodos con secado térmico de depuradora, paja de trigo y virutas de madera, Abstract Energy recovery from biomass and non-recyclable waste products by combustion has become important. One of the most used techniques for this proposal is the co-firing of waste and biomass mixtures, With this new technology, mixtures of different materials have appeared in the industrial facilities and they have to be treated as new fuels because their properties are unknown. Among this properties we include energetic properties that are the objective of the mixing process, and also the ignitability properties. Waste and biomass dusts have ignition properties that have to be taken into account in the design but also in the, prevention and protection process of an industrial facility.. The main objective of this research is to determine the risk of ignition of waste / biomass mixtures layers and how, by adding different quantities of these materials, this risk may vary. To develop this, the minimum ignition temperature on layer is used. Three different samples have been analysed, thermally dried sewage sludge, wheat straw and wood chips.

Effects of biochar prepared from organic waste on soil properties

Biochar is a carbon-rich solid obtained by the thermal decomposition of organic matter under a limited supply of oxygen and at relatively low temperatures. Biochar can be prepared from the pyrolysis of different organic feed- stocks, such as wood and biomass crops, agricultural by-products, different types of waste or paper industry waste materials . The pyrolysis procedure of waste, i.e. sewage sludge, has mainly two advantages, firstly, it removes pathogens from waste and, secondly, biochar can reduce the leaching of heavy metals present in raw sewage sludge. This trend of the use of waste material as feedstocks to the preparation of biochar is increasing in the last years due to industrial development and economic growth imply an increase in waste generation. The application of biochar may have positive effects on soil physical properties as water holding capacity and structure or on soil biological activity and soil quality. Also, biochar can be used to remove water pollutants and can be used in multiple ways in soil remediation due to its adsorption of pesticides or metals. Also, biochar contribute to carbon sequestration due to carbon stability of biochar materials. The objective of this presentation is to review the positive effects of the biochar prepared from organic waste on soil properties.

Plant development effects of biochars from different raw materials

Biochar can provide multiple benefits in the ecosystem. However, the presence of phytotoxic compounds in some biochars is an important concern that needs to be addressed and that depends on the raw material and the pyrolysis conditions used in biochar production. For example, sewage sludge biochars can have elevated heavy metal con- tents as they were present in the feedstock and were enriched during pyrolysis. Also during carbonization, some phytotoxic compounds such as polycyclic aromatic hydrocarbons (PAHs), polyphenols or volatile organic com- pounds (VOCs) could be formed representing a risk of contamination to soils and crops. In this work we report the results from seed germination and plant development for three biochars prepared from wood, paper sludge plus wheat husks and sewage sludge. Five higher plant species (cress, lentils, cucumber, tomato and lettuce) were studied. Biochar from wood shows seed inhibition in several species and the paper sludge biochar on lettuce. For the rest, the effect on seed germination was positive. No inhibition of root growth was detected, but in some cases leaves and stems growth were inhibited. Our results are significant in terms of advancing or current understanding on the impacts of biochar on vegetative growth and linking those effects to biochar properties.

Hybridizing concentrated solar power (CSP) with biogas and biomethane as an alternative to natural gas: Analysis of environmental performance using LCA

Concentrating Solar Power (CSP) plants typically incorporate one or various auxiliary boilers operating in parallel to the solar field to facilitate start up operations, provide system stability, avoid freezing of heat transfer fluid (HTF) and increase generation capacity. The environmental performance of these plants is highly influenced by the energy input and the type of auxiliary fuel, which in most cases is natural gas (NG). Replacing the NG with biogas or biomethane (BM) in commercial CSP installations is being considered as a means to produce electricity that is fully renewable and free from fossil inputs. Despite their renewable nature, the use of these biofuels also generates environmental impacts that need to be adequately identified and quantified. This paper investigates the environmental performance of a commercial wet-cooled parabolic trough 50 MWe CSP plant in Spain operating according to two strategies: solar-only, with minimum technically viable energy non-solar contribution; and hybrid operation, where 12 % of the electricity derives from auxiliary fuels (as permitted by Spanish legislation). The analysis was based on standard Life Cycle Assessment (LCA) methodology (ISO 14040-14040). The technical viability and the environmental profile of operating the CSP plant with different auxiliary fuels was evaluated, including: NG; biogas from an adjacent plant; and BM withdrawn from the gas network. The effect of using different substrates (biowaste, sewage sludge, grass and a mix of biowaste with animal manure) for the production of the biofuels was also investigated. The results showed that NG is responsible for most of the environmental damage associated with the operation of the plant in hybrid mode. Replacing NG with biogas resulted in a significant improvement of the environmental performance of the installation, primarily due to reduced impact in the following categories: natural land transformation, depletion of fossil resources, and climate change. However, despite the renewable nature of the biofuels, other environmental categories like human toxicity, eutrophication, acidification and marine ecotoxicity scored higher when using biogas and BM.

Optimización de la aplicación de lodos de depuración de aguas residuales al abonado o mejora de suelos

El objetivo de este trabajo de investigación fue evaluar el efecto de la aplicación de lodos residuales procedentes de una planta de tratamiento de aguas residuales acondicionados como biosólido para el abonado de tres cultivos agrícolas. Esto se realizó a través del estudio de las variables de producción (desarrollo vegetal de cada cultivo) y de la comparación de las características de los suelos utilizados antes y después de los ensayos experimentales. A través de la investigación se confirmó la mejora en la calidad del suelo y mejor rendimiento de cultivo debido a los biosólidos procedentes de tratamiento de aguas residuales. Este trabajo de investigación de tipo descriptivo y experimental, utilizó lodos optimizados que fueron aplicados a tres cultivos agrícolas de ciclo corto. Fueron evaluados dos cultivos (sandía y tomate) bajo riego y un cultivo (arroz) en secano. En la primera fase del trabajo se realizó la caracterización de los lodos, para ellos se realizaron pruebas físico químicas y microbiológicas. Fue utilizado el método de determinación de metales por espectrometría de emisión atómica de plasma acoplado inductivamente, (ICP-AES) para conocer las concentraciones de metales. La caracterización microbiológica para coliformes totales y fecales se realizó utilizando la técnica del Número más probable (NMP), y para la identificación de organismos patógenos se utilizó el método microbiológico propuesto por Kornacki & Johnson (2001), que se fundamenta en dos procesos: pruebas presuntivas y prueba confirmativa. Tanto los resultados para la determinación de metales y elementos potencialmente tóxicos; como las pruebas para la determinación de microorganismos potencialmente peligrosos, estuvieron por debajo de los límites considerados peligrosos establecidos por la normativa vigente en Panama (Reglamento Técnico COPANIT 47-2000). Una vez establecido la caracterización de los lodos, se evalúo el potencial de nutrientes (macro y micro) presentes en los biosólidos para su potencial de uso como abono en cultivos agrícolas. El secado de lodos fue realizado a través de una era de secado, donde los lodos fueron deshidratados hasta alcanzar una textura pastosa. “La pasta de lodo” fue transportada al área de los ensayos de campo para continuar el proceso de secado y molida. Tres ensayos experimentales fueron diseñados al azar con cinco tratamientos y cuatro repeticiones para cada uno de los tres cultivos: sandía, tomate, arroz, en parcelas de 10m2 (sandía y tomate) y 20 m2 (arroz) para cada tratamiento. Tres diferentes dosis de biosólidos fueron evaluadas y comparadas con un tratamiento de fertilizante comercial y un tratamiento control. La dosis de fertilizante comercial utilizada en cada cultivo fue la recomendada por el Instituto de Investigación Agropecuaria de Panamá. Los ensayos consideraron la caracterización inicial del suelo, la preparación del suelo, semilla, y arreglo topográfico de los cultivos siguiendo las recomendaciones agronómicas de manejo de cultivo establecida por el Instituto de Investigación Agropecuaria. Para los ensayos de sandía y tomate se instaló el sistema de riego por goteo. Se determinaron los ácidos húmicos presentes en los cultivos, y se estudiaron las variables de desarrollo de cada cultivo (fructificación, cosecha, peso de la cosecha, dimensiones de tamaño y color de las frutas, rendimiento, y la relación costo – rendimiento). También se estudiaron las variaciones de los macro y micro nutrientes y las variaciones de pH, textura de suelo y MO disponible al inicio y al final de cada uno de los ensayos de campo. Todas las variables y covariables fueron analizadas utilizando el programa estadístico INFOSAT (software para análisis estadístico de aplicación general) mediante el análisis de varianza, el método de comparaciones múltiples propuesto por Fisher (LSD Fisher) para comparar las medias de los cultivares y el coeficiente de correlación de Pearson que nos permite analizar si existe una asociación lineal entre dos variables. En la evaluación de los aportes del biosólido a los cultivos se observó que los macronutrientes N y P se encontraban de los límites requeridos en cada uno de los cultivos, pero que los niveles de K estuvieron por debajo de los requerimientos de los cultivos. A nivel de la fertilización tradicional con fertilizante químico se observó que la dosis recomendada para cada uno de los cultivos del estudio estaba sobreestimada en los tres principales macronutrientes: Nitrógeno, Fosforo y Potasio. Contenían concentraciones superiores de N, P y K a las requeridas teóricamente por el cultivo. El nutriente que se aporta en exceso es el Fósforo. Encontramos que para el cultivo de sandía era 18 veces mayor a lo requerido por el cultivo, en tomate fue 12 veces mayor y en el cultivo de arroz, 34 veces mayor. El fertilizante comercial tuvo una influencia en el peso final y rendimiento final en cada uno de los cultivos del estudio. A diferencia, los biosólidos tuvieron una influencia directa en el desarrollo de los cultivos (germinación, coloración, tamaño, longitud, diámetro, floración y resistencia a enfermedades). Para el caso de la sandía la dosis de biosólido más cercana al óptimo para el cultivo es la mayor dosis aplicada en este ensayo (97.2 gramos de biosólido por planta). En el caso de tomate, el fertilizante comercial obtuvo los mejores valores, pero las diferencias son mínimas con relación al tratamiento T1, de menor dosis de biosólido (16.2 gramos de biosólido por planta). Los resultados generales del ensayo de tomate estuvieron por debajo del rendimiento esperado para el cultivo. Los tratamientos de aplicación de biosólidos aportaron al desarrollo del cultivo en las variables tamaño, color y resistencia a las enfermedades dentro del cultivo de tomate. Al igual que el tomate, en el caso del arroz, el tratamiento comercial obtuvo los mejores resultados. Los resultados finales de peso y rendimiento del cultivo indican que el tratamiento (T2), menor dosis de biosólido (32.4 gramos por parcela), no tuvo diferencias significativas con los resultados obtenidos en las parcelas con aplicación de fertilizante comercial (T1). El tratamiento T4 (mayor dosis de biosólido) obtuvo los mejores valores para las variables germinación, ahijamiento y espigamiento del cultivo, pero al momento de la maduración obtuvo los menores resultados. Los biosólidos aportan nutrientes a los cultivos y al final del ensayo se observó que permanecen disponibles en el suelo, aportando a la mejora del suelo final. En los tres ensayos, se pudo comprobar que los aportes de los biosólidos en el desarrollo vegetativo de los cultivos. También se encontró en todos los ensayos que no hubo diferencias significativas (p > 0.05) entre los tratamientos de biosólidos y fertilizante comercial. Para obtener mejores resultados en estos tres ensayos se requeriría que a la composición de biosólidos (utilizada en este ensayo) se le adicione Potasio, Calcio y Magnesio en las cantidades requeridas por cada uno de los cultivos. ABSTRACT The objective of this investigation was to evaluate the effect of residual sewage sludge obtained from the residual water of a treatment plant conditioned as Biosolid used on three reliable agricultural crops. The effect of the added sewage sludge was evaluated through the measurement of production variables such as crop plant development and the comparison of the soil characteristics used before and after the experimental tests. This investigation confirmed that biosolids from wastewater treatment can contribute to the growth of these crops. In this experimental approach, optimized sludge was applied to three short-cycle crops including two low-risk crops (watermelon and tomato) and one high-risk crop (rice) all grown on dry land. In the first phase of work, the characteristics of the sludge were assessed using chemical, physical and microbiological tests. The concentrations of metals were determined by atomic emission spectrometry inductively coupled plasma, (ICP-AES). Microbiological characterization was performed measuring total coliform and fecal count using the most probable number technique (NMP) and microbiological pathogens were identified using Kornacki & Johnson (2001) method based on two processes: presumptive and confirmatory tests. Both the results for the determination of metals and potentially toxic elements, as testing for the determination of potentially dangerous microorganisms were below the limits established by the applicable standard in Panama (Technical Regulate COPANIT 47-2000). After the metal and bacterial characterization of the sludge, the presence of macro or micronutrients in biosolids was measured to evaluate its potential for use as fertilizer in the growth of agricultural crops. The sludge was dehydrated via a drying process into a muddy slurry. The pulp slurry was transported to the field trial area to continue the process of drying and grinding. Three randomized experimental trials were designed to test with five treatment regimens and four replications for each of the crops: watermelon, tomato, rice. The five treatment regimens evaluated were three different doses of bio solid with commercial fertilizer treatment control and no fertilizer treatment control. Treatment areas for the watermelon and tomato were 10m2 plots land and for rice was 20m2. The amount of commercial fertilizer used to treat each crop was based on the amount recommended by Agricultural Research Institute of Panama. The experimental trials considered initial characterization of soil, soil preparation, seed, and crop topographical arrangement following agronomic crop management recommendations. For the tests evaluating the growth of watermelons and tomatoes and drip irrigation system was installed. The amount of humic acids present in the culture were determined and developmental variable of each crop were studied (fruiting crop harvest weight, size dimensions and color of the fruit, performance and cost effectiveness). Changes in macro and micronutrients and changes in pH, soil texture and OM available were measured at the beginning and end of each field trial. All variables and covariates were analyzed using INFOSAT statistical program (software for statistical analysis of general application) by analysis of variance, multiple comparisons method as proposed by Fisher (LSD Fisher) to compare the means of cultivars and the Pearson ratio that allows us to analyze if there is a linear association between two variables. In evaluating the contribution of biosolids to agricultural crops, the study determined that the macronutrients N & P were within the requirements of crops, but K levels were below the requirements of crops. In terms of traditional chemical fertilizer fertilization, we observed that the recommended dose for each study crop was overestimated for the three major nutrients: nitrogen, phosphorus and potassium. Higher concentrations containing N, P and K to the theoretically required by the crop. The recommended dose of commercial fertilizer for crops study contained greater amounts of phosphorus, crops that need. The level of phosphorous was found to be18 times greater than was required for the cultivation of watermelon; 12 times higher than required for tomato, and 34 times higher than required for rice cultivation. Phosphorus inputs of commercial fertilizer were a primary influence on the weight and performance of each crop. Unlike biosolids had a direct influence on crop development (germination, color, size, length, diameter, flowering and disease resistance). In the case of growth of watermelons, the Biosolid dose closest to the optimum for cultivation was applied the highest dose in this assay (97.2 grams of bio solids per plant). In the case of tomatoes, commercial fertilizer had the best values but the differences were minimal when compared to treatment T1, the lower dose of sewage sludge (Biosolid 16.2 grams per plant). The overall results for the tomato crop yield of the trial were lower than expected. Additionally, the application of biosolids treatment contributed to the development of fruit of variable size, color and disease resistance in the tomato crops. Similar to the tomato crop, commercial fertilizer treatment provided the best results for the rice crop. The final results of weight and crop yield for rice indicated that treatment with T2 amount of biosolids (34.2 grams per plot) was not significantly different from the result obtained in the application plot given commercial fertilizer (T1). The T4 (higher dose of bio solid) treatment had the best values for the germination, tillering and bolting variables of the rice crop but for fruit ripening yielded lower results. In all three trials, biosolids demonstrated the ability to contribute in the vegetative growth of crops. It was also found in all test no significant differences (p>0.05) between treatment of bio solid and commercial fertilizer. Biosolids provided nutrients to the crops and even at the end of the trial remained available in the ground soil, contributing to the improvement of the final ground. The best results from these three trials is that the use of bio solids such as those used in this assay would require the addition of potassium, calcium and magnesium in quantities required for each crop.

Caracterização microbiológica, química e presença de poluentes orgânicos em amostras de lodo de esgoto de São Paulo

Objetivou-se com este trabalho avaliar o potencial agrícola do lodo de esgoto produzido no estado de São Paulo, bem como, verificar a possibilidade de interação entre a composição química e a abundância relativa de bactérias no lodo. Foram realizadas coletas de amostra de lodo de esgoto em 19 estações de tratamento de esgoto, em três épocas distintas. Nas amostras provenientes das três épocas foram determinados as concentrações dos 16 hidrocarbonetos policíclicos aromáticos (HPAs) listados como prioritários no monitoramento ambiental pela USEPA (acenafteno, acenaftileno, antraceno, benzo(a)antraceno, benzo(a)pireno, benzo(b)fluoranteno, benzo(ghi)perileno, benzo(k)fluoranteno, criseno, dibenzo(a,h)antraceno, fenantreno, fluoranteno, fluoreno, indeno(1,2,3-cd)pireno, naftaleno e pireno). Nas amostras da segunda época de coleta, além da presença de HPAs, determinou-se as concentrações de poluentes orgânicos emergentes (hormônios, produtos farmacêuticos e produtos de uso industrial), realizou-se a caracterização completa segundo a Resolução CONAMA 375/2006 (umidade, pH, N-Kjeldahl e inorgânico, carbono orgânico, cálcio, potássio, fósforo, magnésio, enxofre, boro, cobre, ferro, níquel, manganês, molibdênio, selênio, zinco, alumínio, arsênio, bário, cádmio, cromo, chumbo, mercúrio e sódio) e a caracterização da comunidade bacteriana através de metodologia independente de cultivo (sequenciamento illumina). Os macronutrientes em maiores concentrações no lodo de esgoto são: N > Ca > S > P > Mg > K. Os elementos inorgânicos Ni e Zn apresentaram concentração superior à máxima permitida para utilização agrícola pela resolução Conama 375/2006 em 1 e 3 amostras, respectivamente. A substância inorgânica que mais limita o enquadramento do lodo de esgoto como adubo orgânico (Instrução Normativa 27/2006) é o Hg. Os compostos benzilparabeno, bisfenol AF (BPAF), ácido perfluorooctanoico (PFOA) e tetrabromobisfenol A (TBBPA) não foram detectados. Por outro lado, cimetidina, metilparabeno, bisfenol A (BPA) e triclocarban foram detectados nas 19 amostras avaliadas. O composto presente em maior concentração é o triclocarban. As concentrações de hidrocarbonetos policíclicos aromáticos são baixas, de acordo com a norma Europeia. Os filos Proteobacteria e Bacteroidetes estão presentes em maior abundância relativa. Existe uma comunidade bacteriana núcleo nas estações de tratamento de esgoto do estado de São Paulo, composta por 81 gêneros, presentes nas 19 ETEs avaliadas, dos quais, os que estão em maior abundância relativa são Treponema, Clostridium, Propionibacterium, Syntrophus e Desulfobulbus. A elevação do pH a valores próximos de 12 reduz a diversidade microbiana. Considerando a abundância relativa e a composição química do lodo de esgoto, as estações podem ser agrupadas em três grupos distintos, sendo que um deles é influenciado principalmente pelos teores de Ca, Zn e Cu, o outro pelos teores de Fe e S e o terceiro grupo que foi influenciado pelos demais fatores avaliados.