Performance of a single liquid column damper for the control of dynamic responses of a tension leg platform

Tuned liquid column dampers have been proved to be successful in mitigating the dynamic responses of civil infrastructure. There have been some recent applications of this concept on wind turbines and this passive control system can help to mitigate responses of offshore floating platforms and wave devices. The control of dynamic responses of these devices is important for reducing loads on structural elements and facilitating operations and maintenance (O&M) activities. This paper outlines the use of a tuned single liquid column damper for the control of a tension leg platform supported wind turbine. Theoretical studies were carried out and a scaled model was tested in a wave basin to assess the performance of the damper. The tests on the model presented in this paper correspond to a platform with a very low natural frequency for surge, sway and yaw motions. For practical purposes, it was not possible to tune the liquid damper exactly to this frequency. The consequent approach taken and the efficiency of such approach are presented in this paper. Responses to waves of a single frequency are investigated along with responses obtained from wave spectra characterising typical sea states. The extent of control is quantified using peak and root mean squared dynamic responses respectively. The tests present some guidelines and challenges for testing scaled devices in relation to including response control mechanisms. Additionally, the results provide a basis for dictating future research on tuned liquid column damper based control on floating platforms.

Digital geometric-sequence control technique for bidirectional dual active bridge DC-DC converters used in future electric vehicles

Bidirectional DC-DC converters are widely used in different applications such as energy storage systems, Electric Vehicles (EVs), UPS, etc. In particular, future EVs require bidirectional power flow in order to integrate energy storage units into smart grids. These bidirectional power converters provide Grid to Vehicle (V2G)/ Vehicle to Grid (G2V) power flow capability for future EVs. Generally, there are two control loops used for bidirectional DC-DC converters: The inner current loop and The outer loop. The control of DAB converters used in EVs are proved to be challenging due to the wide range of operating conditions and non-linear behavior of the converter. In this thesis, the precise mathematical model of the converter is derived and non-linear control schemes are proposed for the control system of bidirectional DC-DC converters based on the derived model. The proposed inner current control technique is developed based on a novel Geometric-Sequence Control (GSC) approach. The proposed control technique offers significantly improved performance as compared to one for conventional control approaches. The proposed technique utilizes a simple control algorithm which saves on the computational resources. Therefore, it has higher reliability, which is essential in this application. Although, the proposed control technique is based on the mathematical model of the converter, its robustness against parameter uncertainties is proven. Three different control modes for charging the traction batteries in EVs are investigated in this thesis: the voltage mode control, the current mode control, and the power mode control. The outer loop control is determined by each of the three control modes. The structure of the outer control loop provides the current reference for the inner current loop. Comprehensive computer simulations have been conducted in order to evaluate the performance of the proposed control methods. In addition, the proposed control have been verified on a 3.3 kW experimental prototype. Simulation and experimental results show the superior performance of the proposed control techniques over the conventional ones.

Application of multivariable control using artificial neural networks in a debutanizer distillation column

LOPES, Jose Soares Batista et al. Application of multivariable control using artificial neural networks in a debutanizer distillation column.In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING - COBEM, 19, 5-9 nov. 2007, Brasilia. Anais... Brasilia, 2007

National Cancer Strategy 2006: a Strategy for Cancer Control in Ireland – Evaluation Panel Report

Review of ‘A Strategy for Cancer Control in Ireland’. The review was led by Professor Pádraig Warde of the Princess Margaret Cancer Centre, Toronto.  The evaluation panel was very impressed with the excellent progress in the cancer control system in Ireland since the publication of “A Strategy for Cancer Control in Ireland” in 2006.   Download the report here.

Central Stores Inventory: Employing the IBM 1410 Magnetic Tape Computer System

The Property and Equipment Department has a central supply of automotive parts, tools, and maintenance supplies. This central supply is used to supply the repair shop and also to supply parts to the various field garages and all departments of the Commission. The old procedure involved keeping track manually of all of the parts, which involved some 22,000 items. All records, billings, arid re-order points were kept manually. Mani times the re-order points were located by reaching into a bin and finding nothing there. Desiring to improve this situation, an inventory control system was established for use on the computer. A complete record of the supplies that are stored in the central warehouse was prepared and this information was used to make a catalog. Each time an item is issued or received, it is processed through the inventory program. When the re-order point is reached, a notice is given to reorder. The procedure for taking inventory has been improved. A voucher invoice is now prepared by the computer for all issues to departments. These are some of the many benefits that have been de rived from this system.

Application of multivariable control using artificial neural networks in a debutanizer distillation column

LOPES, Jose Soares Batista et al. Application of multivariable control using artificial neural networks in a debutanizer distillation column.In: INTERNATIONAL CONGRESS OF MECHANICAL ENGINEERING - COBEM, 19, 5-9 nov. 2007, Brasilia. Anais... Brasilia, 2007

Equipment quality control

Mammography equipment must be evaluated to ensure that images will be of acceptable diagnostic quality with lowest radiation dose. Quality Assurance (QA) aims to provide systematic and constant improvement through a feedback mechanism to address the technical, clinical and training aspects. Quality Control (QC), in relation to mammography equipment, comprises a series of tests to determine equipment performance characteristics. The introduction of digital technologies promoted changes in QC tests and protocols and there are some tests that are specific for each manufacturer. Within each country specifi c QC tests should be compliant with regulatory requirements and guidance. Ideally, one mammography practitioner should take overarching responsibility for QC within a service, with all practitioners having responsibility for actual QC testing. All QC results must be documented to facilitate troubleshooting, internal audit and external assessment. Generally speaking, the practitioner’s role includes performing, interpreting and recording the QC tests as well as reporting any out of action limits to their service lead. They must undertake additional continuous professional development to maintain their QC competencies. They are usually supported by technicians and medical physicists; in some countries the latter are mandatory. Technicians and/or medical physicists often perform many of the tests indicated within this chapter. It is important to recognise that this chapter is an attempt to encompass the main tests performed within European countries. Specific tests related to the service that you work within must be familiarised with and adhered too.

O sistema de controlo interno e a qualidade da auditoria

A qualidade da auditoria é uma preocupação crescente no sentido de credibilizar as demonstrações financeiras, pelo que muitos estudos têm sido desenvolvido nos últimos tempos com vista a avaliar quais serão os fatores que maior influência poderão ter na qualidade de uma auditoria. Sendo o Sistema de Controlo Interno (SCI) um elemento fundamental no aumento da fiabilidade da informação importa analisar o contributo do SCI para a qualidade da auditoria. Com base em questionários e entrevistas a Revisores Oficiais de Contas (ROC) procuramos perceber o que é um bom SCI numa entidade e quais os fatores de que depende, bem como o seu contributo para a qualidade da auditoria. Os nossos resultados mostram que os ROC dão grande importância ao SCI ao longo de todo o processo de auditoria, e em particular para a avaliação do risco de distorções relevantes e avaliação do risco de fraude. Mostram ainda que consideram o SCI entre os três fatores mais determinantes da qualidade da auditoria, considerando que o ambiente de controlo e a monitorização dos controlos são os componentes do SCI que mais contribuem para esse facto. Assim, os resultados obtidos evidenciam um contributo positivo do SCI para a qualidade da auditoria.

Idiotypic Immune Networks in Mobile Robot Control

Jerne's idiotypic network theory postulates that the immune response involves inter-antibody stimulation and suppression as well as matching to antigens. The theory has proved the most popular Artificial Immune System (AIS) model for incorporation into behavior-based robotics but guidelines for implementing idiotypic selection are scarce. Furthermore, the direct effects of employing the technique have not been demonstrated in the form of a comparison with non-idiotypic systems. This paper aims to address these issues. A method for integrating an idiotypic AIS network with a Reinforcement Learning based control system (RL) is described and the mechanisms underlying antibody stimulation and suppression are explained in detail. Some hypotheses that account for the network advantage are put forward and tested using three systems with increasing idiotypic complexity. The basic RL, a simplified hybrid AIS-RL that implements idiotypic selection independently of derived concentration levels and a full hybrid AIS-RL scheme are examined. The test bed takes the form of a simulated Pioneer robot that is required to navigate through maze worlds detecting and tracking door markers.

Controller system design using the coefficient diagram method

Coefficient diagram method is a controller design technique for linear time-invariant systems. This design procedure occurs into two different domains: an algebraic and a graphical. The former is closely paired to a conventional pole placement method and the latter consists on a diagram whose reading from the plotted curves leads to insights regarding closed-loop control system time response, stability and robustness. The controller structure has two degrees of freedom and the design process leads to both low overshoot closed-loop time response and good robustness performance regarding mismatches between the real system and the design model. This article presents an overview on this design method. In order to make more transparent the presented theoretical concepts, examples in Matlab®code are provided. The included code illustrates both the algebraic and the graphical nature of the coefficient diagram design method. © 2016, King Fahd University of Petroleum & Minerals.

Idiotypic Immune Networks in Mobile Robot Control

Jerne's idiotypic network theory postulates that the immune response involves inter-antibody stimulation and suppression as well as matching to antigens. The theory has proved the most popular Artificial Immune System (AIS) model for incorporation into behavior-based robotics but guidelines for implementing idiotypic selection are scarce. Furthermore, the direct effects of employing the technique have not been demonstrated in the form of a comparison with non-idiotypic systems. This paper aims to address these issues. A method for integrating an idiotypic AIS network with a Reinforcement Learning based control system (RL) is described and the mechanisms underlying antibody stimulation and suppression are explained in detail. Some hypotheses that account for the network advantage are put forward and tested using three systems with increasing idiotypic complexity. The basic RL, a simplified hybrid AIS-RL that implements idiotypic selection independently of derived concentration levels and a full hybrid AIS-RL scheme are examined. The test bed takes the form of a simulated Pioneer robot that is required to navigate through maze worlds detecting and tracking door markers.

Modelado orientado a objetos del sistema de control de la presión arterial en pacientes sometidos al tratamiento de hemodiálisis

Se ha realizado el modelado orientado a objetos del sistema de control cardiovascular en situaciones de diálisis aplicando una analogía eléctrica en el que se emplean componentes conectados mediante interconexiones. En este modelado se representan las ecuaciones diferenciales del sistema cardiovascular y del sistema de control barorreceptor así como las ecuaciones dinámicas del intercambio de fluidos y solutos del sistema hemodializador. A partir de este modelo se ha realizado experiencias de simulación en condiciones normales y situaciones de hemorragias, transfusiones de sangre y de ultrafiltración e infusión de fluido durante tratamiento de hemodiálisis. Los resultados obtenidos muestran en primer lugar la efectividad del sistema barorreceptor para compensar la hipotensión arterial inducida por los episodios de hemorragia y transfusión de sangre. En segundo lugar se muestra la respuesta del sistema de control ante diferentes tasas de ultrafiltración durante la hemodiálisis y se sugieren valores óptimos para la adecuada operación.

A future dynamically reconfigurable automotive software system

Embedded software systems in vehicles are of rapidly increasing commercial importance for the automotive industry. Current systems employ a static run-time environment; due to the difficulty and cost involved in the development of dynamic systems in a high-integrity embedded control context. A dynamic system, referring to the system configuration, would greatly increase the flexibility of the offered functionality and enable customised software configuration for individual vehicles, adding customer value through plug-and-play capability, and increased quality due to its inherent ability to adjust to changes in hardware and software. We envisage an automotive system containing a variety of components, from a multitude of organizations, not necessarily known at development time. The system dynamically adapts its configuration to suit the run-time system constraints. This paper presents our vision for future automotive control systems that will be regarded in an EU research project, referred to as DySCAS (Dynamically Self-Configuring Automotive Systems). We propose a self-configuring vehicular control system architecture, with capabilities that include automatic discovery and inclusion of new devices, self-optimisation to best-use the processing, storage and communication resources available, self-diagnostics and ultimately self-healing. Such an architecture has benefits extending to reduced development and maintenance costs, improved passenger safety and comfort, and flexible owner customisation. Specifically, this paper addresses the following issues: The state of the art of embedded software systems in vehicles, emphasising the current limitations arising from fixed run-time configurations; and the benefits and challenges of dynamic configuration, giving rise to opportunities for self-healing, self-optimisation, and the automatic inclusion of users’ Consumer Electronic (CE) devices. Our proposal for a dynamically reconfigurable automotive software system platform is outlined and a typical use-case is presented as an example to exemplify the benefits of the envisioned dynamic capabilities.

Design and construction of a two dimensional duct equipped with a wave generator and a variable coastal slope and an ocean wave energy conversion system (OWC)

The aims of this thesis were evaluation the type of wave channel, wave current, and effect of some parameters on them and identification and comparison between types of wave maker in laboratory situations. In this study, designing and making of two dimension channels (flume) and wave maker for experiment son the marine buoy, marine building and energy conversion systems were also investigated. In current research, the physical relation between pump and pumpage and the designing of current making in flume were evaluated. The related calculation for steel building, channels beside glasses and also equations of wave maker plate movement, power of motor and absorb wave(co astal slope) were calculated. In continue of this study, the servo motor was designed and applied for moving of wave maker’s plate. One Ball Screw Leaner was used for having better movement mechanisms of equipment and convert of the around movement to linear movement. The Programmable Logic Controller (PLC) was also used for control of wave maker system. The studies were explained type of ocean energies and energy conversion systems. In another part of this research, the systems of energy resistance in special way of Oscillating Water Column (OWC) were explained and one sample model was designed and applied in hydrolic channel at the Sheikh Bahaii building in Azad University, Science and Research Branch. The dimensions of designed flume was considered at 16 1.98 0. 57 m which had ability to provide regular waves as well as irregular waves with little changing on the control system. The ability of making waves was evaluated in our designed channel and the results were showed that all of the calculation in designed flume was correct. The mean of error between our results and theory calculation was conducted 7%, which was showed the well result in this situation. With evaluating of designed OWC model and considering of changes in the some part of system, one bigger sample of this model can be used for designing the energy conversion system model. The obtained results showed that the best form for chamber in exit position of system, were zero degree (0) in angle for moving below part, forty and five (45) degree in front wall of system and the moving forward of front wall keep in two times of height of wave.

H-infinity control design for time-delay linear systems: a rational transfer function based approach

The aim of this paper is to present new results on H-infinity control synthesis for time-delay linear systems. We extend the use of a finite order LTI system, called comparison system to H-infinity analysis and design. Differently from what can be viewed as a common feature of other control design methods available in the literature to date, the one presented here treats time-delay systems control design with classical numeric routines based on Riccati equations arisen from H-infinity theory. The proposed algorithm is simple, efficient and easy to implement. Some examples illustrating state and output feedback design are solved and discussed in order to put in evidence the most relevant characteristic of the theoretical results. Moreover, a practical application involving a 3-DOF networked control system is presented.