20 Gb/s QPSK transmission using an electro-optically modulated vertical-cavity surface-emitting laser

20 Gb/s QPSK transmission over 100 m of OM3 fibre using an EOM VCSEL under QPSK modulation is reported. Bit-error-ratio measurements are carried out to express the quality of the transmission scheme. © 2011 OSA.

Evaluation of external anchor tags for estimation of growth and survival in tilapia (Oreochromis shiranus chilwae Trewavas)

The effects of tagging with Roy FD-68B T-bar anchor tags on estimates of growth in Tilapia (Oreochromis shiranus chilwae) were investigated in a pond and in a field experiment. In the pond experiment, mean length increments of tagged and marked fish were compared. In the field experiment growth of tagged and "untouched" individual wild fish were compared by measuring scale circuli spacing (Circ.), which is correlated to instantaneous growth rate. Length increments of tagged and untagged/marked fish were not significantly different in either experiment. In the pond experiment, the total mortality rate in the small tagged fish was significantly higher than in the marked fish. The recoveries of tagged fish in the pond experiment increased with fish size. Recoveries exceeded 80% at lengths over 13 cm TL. The ratios of tagged to marked recoveries were 1.02 and 0.74 for large and small fish respectively. The study shows that tagging of Tilapia with Roy anchor tags does not in general alter the growth rates of the fish.

Test on prestressed concrete beam with AFRP spiral confinement and external aramid tendons

This paper describes an experimental study of a new form of prestressed concrete beam. Aramid Fiber Reinforced Polymers (AFRPs) are used to provide compression confinement in the form of interlocking circular spirals, while external tendons are made from parallel-lay aramid ropes. The response shows that the confinement of the compression flange significantly increases the ductility of the beam, allowing much better utilization of the fiber strength. The failure of the beam is characterized by rupture of spiral confinement reinforcement.

External corporate venture capital investment: Towards a framework for capturing and measuring strategic value

This paper presents the initial results of on-going research in the field of external Corporate Venture Capital (CVC) investments, i.e. equity investments of large corporations in entrepreneurial ventures which originated outside the corporation. The research is motivated by the fact that external CVC plays an increasingly important role within the strategy of corporations. Driven by a general trend towards a more open approach to innovation, companies see particular value in external corporate venturing as a tool to gain, for example, access to complementary technologies and a general window on technology developments. The review of literature in the field of external corporate venturing clearly reveals that theoretical gaps exist in understanding mechanisms for capturing value and measurements of this value. To help close these gaps, the research addresses the underlying question "How do corporations and start-ups capture and measure strategic value through external CVC investments" by using embedded, multiple case studies. Following an initial set of case studies, steps towards the development of a framework for capturing and measuring strategic value from CVC investments are outlined within this paper and the resulting preliminary framework is presented. The paper closes with an outlook on ongoing and future research steps. © 2009 PICMET.

Numerical computation of laminar flow in a heated rotating cavity with an axial throughflow of air

A heated rotating cavity with an axial throughflow of cooling air is used as a model for the flow in the cylindrical cavities between adjacent discs of a high-pressure gas-turbine compressor. In an engine the flow is expected to be turbulent, the limitations of this laminar study are fully realised but it is considered an essential step to understand the fundamental nature of the flow. The three-dimensional, time-dependent governing equations are solved using a code based on the finite volume technique and a multigrid algorithm. The computed flow structure shows that flow enters the cavity in one or more radial arms and then forms regions of cyclonic and anticyclonic circulation. This basic flow structure is consistent with existing experimental evidence obtained from flow visualization. The flow structure also undergoes cyclic changes with time. For example, a single radial arm, and pair of recirculation regions can commute to two radial arms and two pairs of recirculation regions and then revert back to one. The flow structure inside the cavity is found to be heavily influenced by the radial distribution of surface temperature imposed on the discs. As the radial location of the maximum disc temperature moves radially outward, this appears to increase the number of radial arms and pairs of recirculation regions (from one to three for the distributions considered here). If the peripheral shroud is also heated there appear to be many radial arms which exchange fluid with a strong cyclonic flow adjacent to the shroud. One surface temperature distribution is studied in detail and profiles of the relative tangential and radial velocities are presented. The disc heat transfer is also found to be influenced by the disc surface temperature distribution. It is also found that the computed Nusselt numbers are in reasonable accord over most of the disc surface with a correlation found from previous experimental measurements. © 1994, MCB UP Limited.

Shroud heat transfer measurements from a rotating cavity with an axial throughflow of air

The paper discusses measurements of heat transfer obtained from the inside surface of the peripheral shroud. The experiments were carried out on a rotating cavity, comprising two 0.985-m-dia disks, separated by an axial gap of 0.065 m and bounded at the circumference by a carbon fiber shroud. Tests were conducted with a heated shroud and either unheated or heated disks. When heated, the disks had the same temperature level and surface temperature distribution. Two different temperature distributions were tested; the surface temperature either increased, or decreased with radius. The effects of disk, shroud, and air temperature levels were also studied. Tests were carried out for the range of axial throughflow rates and speeds: 0.0025 ≤ m ≤ 0.2 kg/s and 12.5 ≤ Ω ≤ 125 rad/s, respectively. Measurements were also made of the temperature of the air inside the cavity. The shroud Nusselt numbers are found to depend on a Grashof number, which is defined using the centripetal acceleration. Providing the correct reference temperature is used, the measured Nusselt numbers also show similarity to those predicted by an established correlation for a horizontal plate in air. The heat transfer from the shroud is only weakly affected by the disk surface temperature distribution and temperature level. The heat transfer from the shroud appears to be affected by the Rossby number. A significant enhancement to the rotationally induced free convection occurs in the regions 2 ≤ Ro ≤ 4 and Ro ≥ 20. The first of these corresponds to a region where vortex breakdown has been observed. In the second region, the Rossby number may be sufficiently large for the central throughflow to affect the shroud heat transfer directly. Heating the shroud does not appear to affect the heat transfer from the disks significantly.