Modelling and analysis of modal behaviour in SOI slot waveguides

Mode behaviour for SOI slot waveguides is modelled and analysed using a numerical full vectorial method based on the film mode matching method (MMM). Only the quasi-TE mode is investigated. Waveguide heights and slot widths, as well as silicon widths are properly chosen with respect to the single mode behaviour in the slot region. Comparison between the effective index method and our side loss method shows that our single mode condition is creditable. The optical power confinement in slot region for the quasi-TE mode is also studied and presented. We demonstrate that the maximum achievable optical power confinement P-slot and the maximum normalized average optical intensity I-slot are 42% and 26 mu m(-2), respectively.

Research on the influence of fabrication parameters on the performance of buried ion-exchanged glass waveguides using the variational method

The variational method is proposed to analyze the influence of the fabrication parameters on the performance of buried K+-Na+ ion-exchanged Er3+-Yb3+ ions co-doped glass waveguide. The unknown parameters of the Hermite-Gaussian functions as the trial field distribution are determined based on the scalar variational principle. It is demonstrated that the results calculated in this paper agree with those measured in the experiment. The mode dimensions, the effective refractive index, and the overlap factor as the functions of the fabrication parameters are investigated. These results of the variational analysis are useful for the design and optimization of Er3+-Yb3+ ions co-doped waveguides.

Paired interference 3-dB coupler based on SOI rib waveguides with anisotropic chemical wet etching

A 3-dB paired interference (PI) optical coupler in silicon-on-insulator (SOI) based on rib waveguides with trapezoidal cross section was designed with simulation by a modified finite-difference beam propagation method (FD-BPM) and fabricated by potassium hydroxide (KOH) anisotropic chemical wet etching. Theoretically, tolerances of width, length, and port distance are more than 1, 100, and 1 mu m, respectively. Smooth interface was obtained with the propagation loss of 1.1 dB/cm at the wavelength of 1.55 mu m. The coupler has a good uniformity of 0.2 dB and low excess loss of less than 2 dB.

Dielectric relaxation and giant dielectric constant of Nb-doped CaCu3Ti4O12 ceramics under dc bias voltage

CaCu3Ti(4-x)Nb(x)O(12) (x = 0, 0.01, 0.08, 0.2) ceramics were fabricated by a conventional solid-state reaction method. The ceramics showed the body-centered cubic structure without any foreign phases and the grain size decreases with Nb doping. Two Debye-type relaxations were observed for the Nb-doped samples at low frequency and high frequency, respectively. The complex electric modulus analysis revealed that the surface layer, grains and grain boundaries contributed to the dielectric constant. The low-frequency dielectric constant relative to the surface layer decreased to a minimum and then increased with the dc bias voltage at 100 Hz, which were well explained in terms of a model containing two metal oxide semiconductors in series, confirming the surface layer in the ceramics. The shift voltage V-B corresponding to the minimal capacitance increased with increase of the composition x. (C) 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Blue-violet Lasing of Optically Pumped GaN-Based Vertical Cavity Surface-Emitting Laser With Dielectric Distributed Bragg Reflectors

Optically pumped GaN-based vertical cavity surface-emitting laser (VCSEL) with two Ta2O5/SiO2 dielectric distributed Bragg reflectors (DBRs) was fabricated via a simplifled procedure direct deposition of the top DBR onto the GaN surface exposed after substrate removal and no use of etching and polishing processes. Blue-violet lasing action was observed at a wavelength of 397.3 ran under optical pumping at room temperature with a threshold pumping energy density of about 71.5 mJ/cm(2). The laser action was further confirmed by a narrow emission linewidth of 0.13 nm and a degree of polarization of about 65%. The result suggests that practical blue-violet GaN-bsaed VCSEL can be realized by optimizing the laser lift-off technique for substrate removal.

Anisotropic transport in quantum waveguides due to the spin-orbit interactions

We theoretically investigate the charge transport in the quantum waveguides in the presence of the Rashba spin-orbit interaction and the Dresselhaus spin-orbit interaction. We find that the interplay between the Rashba spin-orbit interaction and Dresselhaus spin-orbit interaction can induce a symmetry breaking and consequently leads to the anisotropic charge transport in the quantum waveguides, the conductance through the quantum waveguides depends sensitively on the crystallographic orientations of the quantum waveguides. The anisotropy of the charge transport can even survive in the presence of disorder effect in realistic systems.

An investigation of the mode characteristics of SOI submicron rib waveguides using the film mode matching method

The mode characteristics of SOI (silicon-on-insulator) submicron rib waveguides are very different from those of micrometer-sized ones. Using the full-vector film mode matching method, we propose a simple criterion to determine whether a waveguide mode is guided or not. The single-mode condition for deep-etched waveguides is obtained using this criterion. We also obtain the inherent TM mode leakage and sharp cancelation effects due to TE-TM mode coupling in shallow-etched rib waveguides from numerical simulations, which agree well with the analytical results based on total internal reflection and interference theories.

Effects of waveguide length and pump power on the efficiency of wavelength conversion in silicon nanowire waveguides

We point out the use of a wrong definition for conversion efficiency in the literature and analyze the effects of the waveguide length and pump power on conversion efficiency according to the correct definition. The existence of the locally optimal waveguide length and pump power is demonstrated theoretically and experimentally. Further analysis shows that the extremum of conversion efficiency can be achieved by global optimization of the waveguide length and pump power simultaneously, which is limited by just the linear propagation loss and the effective carrier lifetime. (C) 2009 Optical Society of America

Properties of high k gate dielectric gadolinium oxide deposited on Si(100) by dual ion beam deposition (DIBD)

Gadolinium oxide thin films have been prepared on silicon (100) substrates with a low-energy dual ion-beam epitaxial technique. Substrate temperature was an important factor to affect the crystal structures and textures in an ion energy range of 100-500 eV. The films had a monoclinic Gd2O3 structure with preferred orientation ((4) over bar 02) at low substrate temperatures. When the substrate temperature was increased, the orientation turned to (202), and finally, the cubic structure appeared at the substrate temperature of 700 degreesC, which disagreed with the previous report because of the ion energy. The AES studies found that Gadolinium oxide shared Gd2O3 structures, although there were a lot of oxygen deficiencies in the films, and the XPS results confirmed this. AFM was also used to investigate the surface images of the samples. Finally, the electrical properties were presented. (C) 2004 Elsevier B.V. All rights reserved.

Single-mode condition for silicon rib waveguides with large cross sections

The single-mode condition for silicon rib waveguides with large cross sections is obtained using a numerical method based on the finite-difference beam propagation method (FD-BPM). An ultrawide computation window is used to contain the wide mode profile near cutoff. Comparison with previous results shows that the formula predicted by the mode-matching technique is in a better agreement with our results. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

Single-mode behaviour judgment of optical waveguides by imaginary-distance beam propagation method under perfectly matched layer boundary condition

Imaginary-distance beam propagation method under the perfectly matched layer boundary condition is applied to judge single-mode behaviour of optical waveguides, for the first time to our knowledge. A new kind of silicon-on-insulator-based rib structures with half-circle cross-section is presented. The single-mode behaviour of this kind of waveguide with radius 2mum is investigated by this method. It is single-mode when the slab height is not smaller than the radius.

Single-mode condition for silicon rib waveguides with trapezoidal cross-section

Single-mode condition for silicon rib waveguides with trapezoidal cross-section was obtained using a numerical method based on imaginary-distance beam propagation method with non-uniform discretization. Both quasi-transverse-electric and quasi-transverse-magnetic modes were investigated. Simulated single-mode condition is given by a modified equation. Comparison with reported results shows that the Marcatili's method is in a better agreement with our results. (C) 2003 Elsevier B.V. All rights reserved.

Multimode interference 3-dB coupler in silicon-on-insulator based on silicon rib waveguides with trapezoidal cross section

A 3-dB multimode interference optical coupler based on rib waveguides with trapezoidal cross section was designed and fabricated on silicon-on-insulator wafer. Potassium hydroxide (KOH) anisotropic chemical etching of silicon was used to fabricate the waveguides to obtain smooth interface. A modified finite-difference beam propagation method was used to simulate the multimode rib waveguide with slope interfaces. The rms roughness of etching interface is as small as 1.49 nm. The propagation loss of the waveguide is 1.3 dB/cm at wavelength of 1.55 mum. The fabricated 3-dB coupler has a good uniformity of 0.2 dB.

A novel design of grating couplers for efficient broadband coupling between silicon-on-insulator nanophotonic waveguides and fibres

A novel design of out-of-plane grating couplers is proposed for coupling between silicon-on-insulator nanophotonic waveguides and single-mode fibres. The coupler with the first-order diffraction coupling to the optical fibre is actually a second-order reflected grating with two times of period of the first-order grating. To enhance outcoupled power, a back hole is designed to form in the silicon substrate and a kind of metals is placed on the top acting as a reflection layer. The coupler is optimized using coupled-mode- based simulations, showing that, the coupling efficiency to and from tapered optical fibre can be as high as 85% with 1 dB bandwidth about 23nm.

Birefringence of UV-written channel waveguides

The combination of the effective index method and the transfer matrix method is adopted to calculate the indices of quasi-TE and quasi-TM modes in a UV-written channel waveguide, and the difference between the indices is used to characterize its birefringence. The dimensions, the ratio of width to thickness, the original index of the core layer, the index of the cladding, and the index profile are all taken into account. The simulation results indicate that the birefringence decreases with increasing dimensions, ratio of width to thickness, and indices of the cladding; on the contrary, increases of the original index of the core layer and of the vertical index gradient intensified the birefringence. (c) 2005 Society of Photo-Optical Instrumentation Engineers.