A CMOS variable width short-pulse generator circuit for UWB RADAR applications

IEEE International Symposium on Circuits and Systems, pp. 2713 – 2716, Seattle, EUA

Low-cost vibration sensors: tendencies and applications in condition monitoring of machines and structures

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Applications of Fourier methods to the analysis of some stochastic processes

Dissertação de Doutoramento em Matemática: Processos Estocásticos

Collaborative web applications

Trabalho apresentado no âmbito do Mestrado em Engenharia Informática, como requisito parcial para obtenção do grau de Mestre em Engenharia Informática

Transcranial magnetic resonance guided focused ultrasound: neurosurgery applications

Mestrado em Radiações Aplicadas às Tecnologias da Saúde

Effect of temperature on the shear strength of aluminium single lap bonded joints for high temperature applications

An experimental and numerical investigation into the shear strength behaviour of adhesive single lap joints (SLJs) was carried out in order to understand the effect of temperature on the joint strength. The adherend material used for the experimental tests was an aluminium alloy in the form of thin sheets, and the adhesive used was a high-strength high temperature epoxy. Tensile tests as a function of temperature were performed and numerical predictions based on the use of a bilinear cohesive damage model were obtained. It is shown that at temperatures below Tg, the lap shear strength of SLJs increased, while at temperatures above Tg, a drastic drop in the lap shear strength was observed. Comparison between the experimental and numerical maximum loads representing the strength of the joints shows a reasonably good agreement.

25 kV bipolar solid-state Marx generator for industrial food applications

The preliminary results from a bipolar industrial solidstate based Marx generator, developed for the food industry, capable of delivering 25 kV/250 A positive and negative pulses with 12 kW average power, are presented and discussed. This modular topology uses only four controlled switches per cell, 27 cells in total that can be charged up to 1000V each, the two extra cells are used for droop compensation. The triggering signals for all the switches are generated by a FPGA. Considering that biomaterials are similar to resistive type loads, experimental results from this new bipolar 25 kV modulator into resistive loads are presented and discussed.

Spent coffee grounds for biodiesel production and other applications

This work evaluates the possibility of using spent coffee grounds (SCG) for biodiesel production and other applications. An experimental study was conducted with different solvents showing that lipid content up to 6 wt% can be obtained from SCG. Results also show that besides biodiesel production, SCG can be used as fertilizer as it is rich in nitrogen, and as solid fuel with higher heating value (HHV) equivalent to some agriculture and wood residues. The extracted lipids were characterized for their properties of acid value, density at 15 °C, viscosity at 40 °C, iodine number, and HHV, which are negatively influenced by water content and solvents used in lipid extraction. Results suggest that for lipids with high free fatty acids (FFA), the best procedure for conversion to biodiesel would be a two-step process of acid esterification followed by alkaline transesterification, instead of a sole step of direct transesterification with acid catalyst. Biodiesel was characterized for its properties of iodine number, acid value, and ester content. Although these quality parameters were not within the limits of NP EN 14214:2009 standard, SCG lipids can be used for biodiesel, blended with higher-quality vegetable oils before transesterification, or the biodiesel produced from SCG can be blended with higher-quality biodiesel or even with fossil diesel, in order to meet the standard requirements.

Acute schistosomiasis: clinical, diagnostic and therapeutic features

Three distinct syndromes caused by schistosomiasis have been described: cercarial dermatitis or swimmer's itch, acute schistosomiasis or Katayama fever, and chronic schistosomiasis. Complications of acute schistosomiasis have also been reported. The absence of a serological marker for the acute stage has hindered early diagnosis and treatment. Recently, an ELISA test using KLH (keyhole limpet haemocyanin) as antigen, has proved useful in differentiating acute from chronic schistosomiasis mansoni. Clinical and experimental evidence indicate that steroids act synergistically with schistosomicides in the treatment of Katayama syndrome. In this paper, clinical, diagnostic and therapeutic features of acute schistosomiasis are updated.

Nocardia infection in renal transplant recipient: diagnostic and therapeutic considerations

In the present report the authors discuss the diagnostic difficulties, therapeutic measures and the clinical course of Nocardia infection which occurred among renal transplant recipients at the University Hospital of the Faculty of Medicine of Ribeirão Preto, University of São Paulo (UH-FRP), from 1968 to 1991. Among 500 individuals submitted to renal transplant, 9 patients developed Nocardiosis at varying times after transplant (two months to over two years). All the patients had pulmonary involvement and their most common symptoms were fever, cough and pleural pain. Dissemination of the process is common and three patients presented cutaneous abscesses, four CNS involvement and one had pericarditis due to Nocardia. The diagnostic is quite difficult since there is no specific clinical picture, concomitant infections are frequent and the microorganism presents slow growth in culture (ranging from four to forty days, in our experience). In this report, three cases were only diagnosed by necropsy. The treatment of choice is a combination of Sulfamethoxazole and Trimethoprim (SMX-TMP). In the present series, overall mortality was 77% (7 cases) and in five of the patients who died the diagnosis was late. All the patients who had CNS involvement died.

Some pioneers of the applications of fractional calculus

In the last decades fractional calculus (FC) became an area of intensive research and development. This paper goes back and recalls important pioneers that started to apply FC to scientific and engineering problems during the nineteenth and twentieth centuries. Those we present are, in alphabetical order: Niels Abel, Kenneth and Robert Cole, Andrew Gemant, Andrey N. Gerasimov, Oliver Heaviside, Paul Lévy, Rashid Sh. Nigmatullin, Yuri N. Rabotnov, George Scott Blair.

Creating and optimizing client-server applications on mobile devices

Mobile devices are embedded systems with very limited capacities that need to be considered when developing a client-server application, mainly due to technical, ergonomic and economic implications to the mobile user. With the increasing popularity of mobile computing, many developers have faced problems due to low performance of devices. In this paper, we discuss how to optimize and create client-server applications for in wireless/mobile environments, presenting techniques to improve overall performance.

Dual-phase inkjet printed electrochromic layers based on PTA and WOX/TiO2 nanoparticles for electrochromic applications

Thesis submitted in Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa for the degree of Master in Materials Engineering

Processing and characterization of 3D dense chitosan pieces, for orthopedic applications, by adding plasticizers

In this work, plasticizer agents were incorporated in a chitosan based formulation, as a strategy to improve the fragile structure of chitosan based-materials. Three different plasticizers: ethylene glycol, glycerol and sorbitol, were blended with chitosan to prepare 3D dense chitosan specimens. The properties of the obtained structures were assessed for mechanical, microstructural, physical and biocompatibility behavior. The results obtained revealed that from the different specimens prepared, the blend of chitosan with glycerol has superior mechanical properties and good biological behavior, making this chitosan based formulation a good candidate to improve robust chitosan structures for the construction of bioabsorbable orthopedic implants.