Desenvolvimento de filmes nanocompósitos de isolado protéico de corvina (micropogonias furnieri) e argila organofílica

O desenvolvimento de filmes e coberturas é um processo de transformação que utiliza polímeros capazes de formar uma matriz contínua. As proteínas de pescado apresentam propriedades que são vantajosas no preparo de biofilmes, como habilidade para formar redes, plasticidade e elasticidade, apresentando boa barreira ao oxigênio, mas sua barreira ao vapor de água é baixa devido à sua natureza hidrofílica. Estas propriedades podem ser melhoradas aplicando nanotecnologia, incluindo materiais como as nanoargilas. O objetivo do presente trabalho foi desenvolver filmes nanocompósitos a partir de biopolímeros protéicos provenientes de isolados protéicos de corvina (Micropogonias furnieri) e argilas organofílicas. O isolado protéico de corvina (IPC) foi obtido utilizando processo de variação de pH para solubilizar e isolar proteína. Os filmes poliméricos foram desenvolvidos pela técnica de “casting”. Para o desenvolvimento de filmes nanocompósitos de isolado protéico de corvina (IPC) e montmorilonita foi executado um planejamento experimental de 3 níveis e 3 fatores com 3 réplicas no ponto central. Os resultados foram submetidos à metodologia de superfície de resposta (MSR) para estudar os efeitos simultâneos das variáveis independentes, concentração de IPC (IPC = 2; 3,5 e 5 g/100 g de solução filmogênica); concentração de montmorilonita (MMT = 0,3; 0,5 e 0,7 g/100 g de solução filmogênica); e plastificante glicerol (G = 25, 30 e 35 g/100 g de IPC em base seca) sobre as respostas resistência à tração (MPa), elongação (%), força na ruptura (N), permeabilidade ao vapor de água (g mm m-2 d -1 KPa-1 ) e solubilidade (%). O isolado protéico obtido de carne mecanicamente separada de corvina apresentou 97,87% de proteína (em base seca), boa capacidade de retenção de água e solubilidade. Os valores de resistência à tração variaram entre 7,2 e 10,7 MPa e os valores de elongação de 39,6 a 45,8%. Os valores encontrados para PVA no presente trabalho encontram-se entre 3,2 e 5,5 g mm m-2 d -1 KPa-1 . Os filmes nanocompósitos produzidos a partir de IPC e MMT foram promissores, do ponto de vista das propriedades mecânicas, aparência visual e fácil manuseio, bem como baixa permeabilidade ao vapor de água e a baixa solubilidade. Com relação às propriedades mecânicas, a concentração de IPC e MMT foi o principal fator que influenciou no desenvolvimento dos filmes nanocompósitos. O planejamento experimental utilizado determinou que 3,5 g de IPC; 0,5 g de MMT e 30 (g/100g de IPC) de glicerol seriam os parâmetros ideais para desenvolvimento de filmes nanocompósitos utilizando a técnica de “casting”. As coberturas de isolado protéico de corvina (IPC) e as coberturas de IPC e MMT foram aplicadas em mamão minimamente processado para avaliar sua vida- útil. O revestimento com cobertura de isolado protéico de corvina e montmorilonita aplicado em mamão minimamente processado apresentou menor perda de massa 5,26%, menor crescimento microbiano e menor diminuição de firmeza, luminosidade e pH conseqüentemente apresentou os melhores resultados na cobertura de mamão minimamente processado, quando comparados com a amostra controle sem cobertura.

Produção de carboidratos a partir do efluente de laticínios tratado por cianobactéria

Nesta tese foi demonstrado o potencial de produção de carboidratos por Aphanothece microscopica Nägeli cultivada no efluente oriundo de uma indústria de laticínios. Para tanto, o trabalho é composto de quatro artigos que objetivaram avaliar a produção de carboidratos em função da temperatura, inóculo e razões C/N e N/P do elfluente, bem como a possibilidade de reúso da água residuária. Foram utilizadas temperaturas de (10, 20 e 30ºC) e inóculo (100, 200 e 300 mg.L-1). A melhor condição indicada foi quando utilizou-se a temperatura de 30°C e 200 mg.L-1 de inóculo. Na sequência, considerando a temperatura e a concentração celular selecionada, foi estudada a influência das razões C/N e N/P na produção de carboidratos. Para tal, C/N (20, 40 e 60) e N/P (5, 10 e 15) na produção de carboidratos extracelulares foram avaliadas em cultivos a 30°C, tendo como inóculo 200 mg.L-1. Os melhores resultados obtidos, foram quando foi utilizado C/N 60 e N/P 10. Uma vez definidas as melhores condições de produção de carboidratos, foi estudado o processo de separação de biomassa do meio de cultivo, a partir dos coagulantes FeCl3, Al2(SO4)3 e tanino. O efeito dos coagulantes na separação da biomassa foram estudados, quanto ao pH (6,0, 7,0 e 8,0) e concentração de coagulantes (50, 300 e 550 mg.L-1), utilizando como parâmetro de medida, a eficiência de remoção de DQO, turbidez e sólidos suspensos (SS). Os resultados demonstraram que as concentrações de coagulantes influenciaram significativamente ao nível de significância de 5 %, na separação da biomassa, com eficiência significativa na remoção da DQO, turbidez e SS. A melhor condição avaliada foi a que utilizou tanino na concentração de 300 mg.L-1 e pH 7,0, o que resultou em uma água residuária com remoção média de 96 % da turbidez, com potencial de ser reutilizada. Por fim, foi realizada a identificação de carboidratos gerados por Aphanothece microscopica Nägeli. Os resultados evidenciaram uma biomassa com até 33,5 % de carboidratos totais, perfazendo uma fração de carboidratos extracelulares, na fase estacionária de crescimento celular, de aproximadamente 25 % e 8 % os carboidratos da parede celular. Ficou demonstrado ainda que a composição dos carboidratos extracelulares do microorganismo em estudo é constituído por mono e dissacarídeos perfazendo concentrações na ordem de 12,88 % de glicose, 3,54 % de rafinose, 3,43 % sacarose, 2,13 % de frutose e 2,45 % de ribose. Ficou demonstrado o potencial de produção de carboidratos por Aphanothece microscopica Nägeli quando cultivada no efluente da indústria de laticínios.

Adsorção de corantes têxteis aniônicos e catiônicos em resíduos do processamento de fios de algodão modificados quimicamente

The textile industry generates a large volume of high organic effluent loading whoseintense color arises from residual dyes. Due to the environmental implications caused by this category of contaminant there is a permanent search for methods to remove these compounds from industrial waste waters. The adsorption alternative is one of the most efficient ways for such a purpose of sequestering/remediation and the use of inexpensive materials such as agricultural residues (e.g., sugarcane bagasse) and cotton dust waste (CDW) from weaving in their natural or chemically modified forms. The inclusion of quaternary amino groups (DEAE+) and methylcarboxylic (CM-) in the CDW cellulosic structure generates an ion exchange capacity in these formerly inert matrix and, consequently, consolidates its ability for electrovalent adsorption of residual textile dyes. The obtained ionic matrices were evaluated for pHpcz, the retention efficiency for various textile dyes in different experimental conditions, such as initial concentration , temperature, contact time in order to determine the kinetic and thermodynamic parameters of adsorption in batch, turning comprehensive how does occur the process, then understood from the respective isotherms. It was observed a change in the pHpcz for CM--CDW (6.07) and DEAE+-CDW (9.66) as compared to the native CDW (6.46), confirming changes in the total surface charge. The ionized matrices were effective for removing all evaluated pure or residual textile dyes under various tested experimental conditions. The kinetics of the adsorption process data had best fitted to the model a pseudosecond order and an intraparticle diffusion model suggested that the process takes place in more than one step. The time required for the system to reach equilibrium varied according to the initial concentration of dye, being faster in diluted solutions. The isotherm model of Langmuir was the best fit to the experimental data. The maximum adsorption capacity varied differently for each tested dye and it is closely related to the interaction adsorbent/adsorbate and dye chemical structure. Few dyes obtained a linear variation of the balance ka constant due to the inversion of temperature and might have influence form their thermodynamic behavior. Dyes that could be evaluated such as BR 18: 1 and AzL, showed features of an endothermic adsorption process (ΔH° positive) and the dye VmL presented exothermic process characteristics (ΔH° negative). ΔG° values suggested that adsorption occurred spontaneously, except for the BY 28 dye, and the values of ΔH° indicated that adsorption occurred by a chemisorption process. The reduction of 31 to 51% in the biodegradability of the matrix after the dye adsorption means that they must go through a cleaning process before being discarded or recycled, and the regeneration test indicates that matrices can be reused up to five times without loss of performance. The DEAE+-CDW matrix was efficient for the removal of color from a real textile effluent reaching an UV-Visible spectral area decrease of 93% when applied in a proportion of 15 g ion exchanger matrix L-1 of colored wastewater, even in the case of the parallel presence of 50 g L-1 of mordant salts in the waste water. The wide range of colored matter removal by the synthesized matrices varied from 40.27 to 98.65 mg g-1 of ionized matrix, obviously depending in each particular chemical structure of the dye upon adsorption.

Photocatalytic Degradation of Anthracene in Closed System Reactor

Polycyclic aromatic hydrocarbons (PAHs) represent a large class of persistent organic pollutants in an environment of special concern because they have carcinogenic and mutagenic activity. In this paper, we focus on and discuss the effect of different parameters, for instance, initial concentration of Anthracene, temperature, and light intensity, on the degradation rate. These parameters were adjusted at pH 6.8 in the presence of the semiconductor materials (TiO2) as photocatalysts overUVlight. The main product of Anthracene photodegradation is 9,10-Anthraquinone which isidentified and compared with the standard compound by GC-MS. Our results indicate that the optimum conditions for the best rate of degradation are 25 ppm concentration of Anthracene, regulating the reaction vessel at 308.15 K and 2.5 mW/cm(2) of light intensity at 17 5mg/100 mL of titanium dioxide (P25).

Equilibrium Sorption Studies of Hg (II) Ions from Aqueous Solution using Powdered Swamp Arum ( Lasimorpha senegalensis ) Seeds.

The potential of swamp arum ( Lasimorpha senegalensis ) seeds as a low-cost adsorbent for the removal of Hg (II) ions from aqueous solution was investigated in this study. The influence of initial metal concentration on the percent adsorption of Hg (II) ions onto powdered swamp arum seeds was studied in a batch system and the filtrate was analyzed using Atomic Absorption Spectrometry (AAS). The percent adsorbed for 10, 20, 40, 60 and 80 mg/L of the aqueous solution were 97.7, 98.9, 99.3, 99.7, and 96.5% respectively. Three isotherms; Langmuir, Freundlich, and BET were used to model the equilibrium sorption of Hg (II) ions onto powdered swamp arum seeds, with a correlation coefficient of 0.998, 0.784 and0.842 respectively. The Langmuir model fitted the equilibrium data best, with a correlation coefficient of 0.998 and a maximum adsorption capacity qm, of 5.917 mg/g. Thus, indicating monolayer coverage on the adsorbent. The results showed that swamp arum seed have the potential to be applied as alternative lowcost biosorbent in the remediation of heavy metal contamination in waste water.

Aproveitamento de resíduos minerais na formulação de argamassas para a construção civil

Current environmental concerns include the excessive consumption and inefficient use of non-renewable natural resources. The construction industry is considered one of the largest consumers of natural raw materials, significantly contributing to the environmental degradation of the planet. The use of calcareous quarry (RPPC) and porcelain tile polishing residues (RPP) as partial replacements of the cement in mortars is an interesting alternative to minimize the exploration of considerably large amounts of natural resources. The present study aimed at investigating the properties of fresh and hardened mortars produced using residues to replace cement. The residues used were fully characterized to determine their specific mass, unitary mass, particle size distribution and morphology, and composition. The performance of the mortars was compared to that of reference compositions, prepared without residues. A total of 18 compositions were prepared, 16 using residues and 2 reference ones. The mortars were prepared using Portland CP II F 32 cement, CH I hydrated lime, river sand and tap water. The compositions of the mortars were 1:1:6 and 1:0.5:4.5 (vol%), and water to cement ratios of 1.87 and 1.45 were used, respectively. The mortars in the fresh state were evaluated by consistency index, water retention, density of mass and incorporated air content tests. In their hardened state, the mortars were evaluated by apparent mass density, modulus of elasticity, flexural tensile strength, compressive strength and water absorption by capillarity. The mortars were also analyzed by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and fluorescence. Finally, they were classified according to NBR 13281 standards. The mortars prepared using residues partially replacing the cement exhibited lower modulus of elasticity compared to the reference compositions, thus improving the performance in their intended use. On the downside, the water absorption by capillarity was affected by the presence of residues and both the tensile and compressive strength were reduced. However, from the overall standpoint, the replacement of cement by calcareous quarry or porcelain tile polishing residues did not result in significant changes in the properties of the mortars. Therefore, compositions containing these residues can be used in the construction industry

Síntese, estudo cinético e análise microestrutural do sistema cério-níquel obtido pelo método pechini

The cerium oxide has a high potential for use in removing pollutants after combustion, removal of organic matter in waste water and the fuel-cell technology. The nickel oxide is an attractive material due to its excellent chemical stability and their optical properties, electrical and magnetic. In this work, CeO2-NiO- systems on molars reasons 1:1(I), 1:2(II) e 1:3(III) metal-citric acid were synthesized using the Pechini method. We used techniques of TG / DTG and ATD to monitor the degradation process of organic matter to the formation of the oxide. By thermogravimetric analysis and applying the dynamic method proposed by Coats-Redfern, it was possible to study the reactions of thermal decomposition in order to propose the possible mechanism by which the reaction takes place, as well as the determination of kinetic parameters as activation energy, Ea, pre-exponential factor and parameters of activation. It was observed that both variables exert a significant influence on the formation of complex polymeric precursor. The model that best fitted the experimental data in the dynamic mode was R3, which consists of nuclear growth, which formed the nuclei grow to a continuous reaction interface, it proposes a spherical symmetry (order 2 / 3). The values of enthalpy of activation of the system showed that the reaction in the state of transition is exothermic. The variables of composition, together with the variable temperature of calcination were studied by different techniques such as XRD, IV and SEM. Also a study was conducted microstructure by the Rietveld method, the calculation routine was developed to run the package program FullProf Suite, and analyzed by pseudo-Voigt function. It was found that the molar ratio of variable metal-citric acid in the system CeO2-NiO (I), (II), (III) has strong influence on the microstructural properties, size of crystallites and microstrain network, and can be used to control these properties

Desenvolvimento de membranas porosas de alumina para fins de tratamento de efluente industrial têxtil

Textile production has been considered as an activity of high environmental impact due to the generation of large volumes of waste water with high load of organic compounds and strongly colored effluents, toxic and difficult biodegradability. This thesis deals with obtaining porous alumina ceramic membranes for filtration of textile effluent in the removal of contaminants, mainly color and turbidity. Two types of alumina with different particle sizes as a basis for the preparation of formulation for mass production of ceramic samples and membranes. The technological properties of the samples were evaluated after using sintering conditions: 1,350ºC-2H, 1,450ºC-30M, 1,450ºC-2H, 1,475ºC-30M and 1,475ºC-2H. The sintered samples were characterized by XRD, XRF, AG, TG, DSC, DL, AA, MEA, RL, MRF-3P, SEM and Intrusion Porosimetry by Mercury. After the characterization, a standard membrane was selected with their respective sintering condition for the filterability tests. The effluent was provided by a local Textile Industry and characterized at the entry and exit of the treatment plant. A statistical analysis was used to study the effluent using the following parameters: pH, temperature, EC, SS, SD, oil and grease, turbidity, COD, DO, total phosphorus, chlorides, phenols, metals and fecal coliform. The filtered effluent was evaluated by using the same parameters. These results demonstrate that the feasibility of the use of porous alumina ceramic membranes for removing contaminants from textile effluent with improved average pore size of 0.4 micrometre (distribution range varying from 0,025 to 2.0 micrometre), with total porosity of 29.66%, and average percentages of color removal efficiency of 89.02%, 92.49% of SS, turbidity of 94.55%, metals 2.70% (manganese) to 71.52% (iron) according to each metal and COD removal of 72.80%

Eutrofização e qualidade da água na piscicultura: consequências e recomendações

The eutrophication (cultural or anthropogenic) is induced by man and can have different origins, such as domestic sewage, industrial and agricultural activities, including the effluent still breeding systems of aquatic organisms. The expansion of aquaculture, with production of biomass and increase of nutrients in water may cause acceleration of productivity of algae, changing the ecology of aquatic systems. In addition, these waste water may present a risk to health through the transfer of pathogens from manure, plant residues, composted material, among others that are major sources of organic waste in some farming systems. Depending on the trophic level of fish ponds, which are dynamic environments, different planktonic species with short reproductive cycle and adapted to the changes contained in these systems can appear in high abundance. Water quality in the systems for raising fish is related to several factors, such as water source, management (liming, fertilizing, cleaning), cultivated species and quantity and composition of exogenous food. In order to minimize environmental impacts, there are techniques to improve the quality of water in fish farming systems and thus satisfactory answers can be obtained through the application of management practices. This paper aims to review the subject that deals with changes in water quality resulting from the activity of freshwater fish culture in Brazil. Search also recommend techniques of good management practices to minimize the impact generated by the activity.

Immobilized Microalgae for Nutrient Recovery from Source Separated Urine

Shortages in supply of nutrients and freshwater for a growing human population are critical global issues. Traditional centralized sewage treatment can prevent eutrophication and provide sanitation, but is neither efficient nor sustainable in terms of water and resources. Source separation of household wastes, combined with decentralized resource recovery, presents a novel approach to solve these issues. Urine contains within 1 % of household waste water up to 80 % of the nitrogen (N) and 50 % of the phosphorus (P). Since microalgae are efficient at nutrient uptake, growing these organisms in urine might be a promising technology to concomitantly clean urine and produce valuable biomass containing the major plant nutrients. While state-of-the-art suspension systems for algal cultivation have mayor shortcomings in their application, immobilized cultivation on Porous Substrate Photobioreactors (PSBRs) might be a feasible alternative. The aim of this study was to develop a robust process for nutrient recovery from minimally diluted human urine using microalgae on PSBRs. The green alga Desmodesmus abundans strain CCAC 3496 was chosen for its good growth, after screening 96 algal strains derived from urine-specific isolations and culture collections. Treatment of urine, 1:1 diluted with tap water and without addition of nutrients, was performed at a light intensity of 600 μmol photons m-2 s-1 with 2.5 % CO2 and at pH 6.5. A growth rate of 7.2 g dry weight m-² day-1 and removal efficiencies for N and P of 13.1 % and 94.1 %, respectively, were determined. Pre-treatment of urine with activated carbon was found to eliminate possible detrimental effects of pharmaceuticals. These results provide a basis for further development of the technology at pilot-scale. If found to be safe in terms human and environmental health, the biomass produced from three persons could provide the P for annual production of 31 kg wheat grain and 16 kg soybean, covering the caloric demand in food for almost one month of the year for such a household. In combination with other technologies, PSBRs could thus be applied in a decentralized resource recovery system, contributing to locally close the link between sanitation and food production.

MATURE FINE TAILINGS (MFTs): A STUDY OF COMPRESSIVE STRENGTH AND RHEOLOGICAL PROPERTIES OF ATHABASCA OIL SANDS PETROLEUM MINING WASTE APPLIED IN CONCRETE MIXTURES

This study investigates the compressive properties of concrete incorporating Mature Fine Tailings (MFTs) waste stream from a tar sands mining operation. The objectives of this study are to investigate material properties of the MFT material itself, as well as establish general feasibility of the utilization of MFT material in concrete mixtures through empirical data and visual observations. Investigations undertaken in this study consist of moisture content, materials finer than No. 200 sieve, Atterburg Limits as well as visual observations performed on MFT material as obtained. Control concrete mixtures as well as MFT replacement mixture designs (% by wt. of water) were guided by properties of the MFT material that were experimentally established. The experimental design consists of compression testing of 4”-diameter concrete cylinders of a control mixture, 30% MFT, 50% MFT and 70% MFT replacement mixtures with air-entrainer additive, as well as a control mixture and 30% MFT replacement mixture with no air-entrainer. A total of 6 mixtures (2 control mixtures, 4 replacement mixtures) moist-cured in lime water after 24 hours initial curing were tested for ultimate compressive strength at 7 days and 28 days in accordance to ASTM C39. The test results of fresh concrete material show that the addition of air-entrainer to the control mixture increases slump from 4” to 5.5”. However, the use of MFT material in concrete mixtures significantly decreases slump as compared to controls. All MFT replacement mixtures (30%, 50%, and 70%) with air-entrainer present slumps of 1”. 30% MFT with no air-entrainer presents a slump of 1.5”. It was found that 7-day ultimate compressive stress was not a good predictor of 28-day ultimate compressive stress. 28-day results indicate that the use of MFT material in concrete with air-entrainer decreases ultimate compressive stress for 30%, 50% and 70% MFT replacement amounts by 14.2%, 17.3% and 25.1% respectively.

Effect of cement type and water storage time on the push-out bond strength of a glass fiber post

This study investigated the effects of the cement type and the water storage time on the push-out bond strength of a glass fiber post. Glass fiber posts (Fibrekor, Jeneric Pentron) were luted to post spaces using a self-cured resin cement (C&B Cement [CB]), a glass ionomer cement (Ketac Cem [KC]) or a resin-modified glass ionomer cement (GC FujiCEM [FC]) according to the manufacturers’ instructions. For each luting agent, the specimens were exposed to one of the following water storage times (n=5): 1 day (T1), 7 days (T7), 90 days (T90) and 180 days (T180). Push-out tests were performed after the storage times. Control specimens were not exposed to water storage, but subjected to the push-out test 10 min after post cementation. Data (in MPa) were analyzed by Kruskal-Wallis and Dunn`s test (α=0.05). Cement type and water storage time had a significant effect (p<0.05) on the push-out bond strength. CB showed significantly higher values of retention (p<0.05) than KC and FC, irrespective of the water storage time. Water storage increased significantly the push-out bond strength in T7 and T90, regardless of the cement type (p<0.05). The results showed that fiber posts luted to post spaces with the self-cured resin cement exhibited the best bonding performance throughout the 180-day water storage period. All cements exhibited a tendency to increase the bond strength after 7 and 90 days of water storage, decreasing thereafter.

Mechanical properties of concrete produced with a composite of water treatment sludge and sawdust

In developing countries such as Brazil, the wastes generated in the decanters and filters of water treatment plants are discharged directly into the same rivers and streams that supply water for treatment. Another environmental problem is the unregulated discard of wood wastes. The lumber and wood products industry generates large quantities of this waste, from logging to the manufacture of the end product. Brazil has few biomass plants and therefore only a minor part of these wastes are reused. This paper presents the results of the first study involving a novel scientific and technological approach to evaluate the possibility of combining these two types of wastes in the production of a light-weight composite for concrete. The concrete produced with cement:sand:composite:water mass ratios of 1:2.5:0.67:0.6 displayed an axial compressive strength of 11.1 MPa, a compressive and diametral tensile strength of 1.2 MPa, water absorption of 8.8%, and a specific mass of 1.847 kg/m(3). The mechanical properties obtained with this concrete render it suitable for application in non-structural elements. (C) 2010 Elsevier Ltd. All rights reserved.