Formation and characterization of soy bean oil/surfactant/water microemulsions

Pseudoternary phase diagrams, at 25 degrees C, were constructed for the systems soy bean oil (SBO)/surfactant/water, with single anionic sodium bis(2-ethylhexyl)sulfosuccinate (AOT), nonionic monoolein (MO) and mixtures of these surfactants, showing the isotropic phase of W/O microemulsions (MEs). The area of ME formation in the phase diagrams was shown to be dependent of the relative amount of surfactants, being larger for MO:AOT equals to 2:1. Rheological and dynamic light scattering (DLS) studies indicated that the viscosity of the isotropic ME phase exhibited two different behaviors depending on composition. The viscosity of dry MEs initially decreased with increasing amount of water following a dilution line in the phase diagram, i.e., a constant surfactant:SBO percentage ratio. As the water content increased the relative viscosity attained a minimum and then increased. This minimum could be related to the transition between two ME regions, L-2 and L'(2), having different characteristics. DLS measurements confirm the existence of ordinary W/O ME droplets in the L-2 region and suggest the existence of another structure in the L'(2) region. The size of the MEs droplets in L-2 phase ranges from 3.6 to 16.5 nm, depending on composition of SBO, surfactant and water. Small angle X-ray scattering (SAXS) also indicates the existence of structures with different characteristics, for the SAXS curves exhibit a typical micelle asymmetrical peak at low scattering vector q for MEs in L-2 but a symmetrical correlation peak at higher q vector in L'(2). (c) 2006 Elsevier B.V. All rights reserved.

beta-ZnMoO4 microcrystals synthesized by the surfactant-assisted hydrothermal method: Growth process and photoluminescence properties

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Highly swollen liquid crystals as new reactors for the synthesis of nanomaterials

Synthesis and self-assembly of nanomaterials can be controlled by the properties of soft matter. on one hand, dedicated nanoreactors such as reverse microemulsions or miniemulsions can be designed. on the other hand, direct shape control can be provided by the topology of liquid crystals that confine the reacting medium within a specific geometry. In the first case, the preparation of micro- or miniemulsions generally requires energetic mechanical stirring. The second approach uses thermodynamically stable systems, but it remains usually limited to binary (water + surfactant) systems. We report the preparation of different families of materials in highly ordered quaternary mediums that exhibit a liquid crystal structure with a high cell parameter. They were prepared with the proper ratios of salted water, nonpolar solvent, surfactant. and cosurfactants that form spontaneously swollen hexagonal phases. These swollen liquid crystals can be prepared from all classes of surfactants (cationic, anionic, and nonionic). They contain a regular network of parallel cylinders, whose diameters can be swollen with a nonpolar solvent, that are regularly spaced in a continuous aqueous salt solution. We demonstrate in the present report that both aqueous and organic phases can be used as nanoreactors for the preparation of materials. This property is illustrated by various examples such as the synthesis of platinum nanorods prepared in the aqueous phase or zirconia needles or the photo- or gamma-ray-induced polymerization of polydiacetylene in the organic phase. In all cases, materials can be easily extracted and their final shapes are directed by the structure-directing effect imposed by the liquid crystal.

Efeitos tóxicos de surfactantes fitossanitários para o peixe mato grosso (Hyphessobrycon eques)

Toxic effects of phytosanitary surfactants for jewel tetra (Hyphessobrycon eques). Surfactants are amphipatic molecules that reduce the surface tension of water and make up the inert components of pesticide formulations. Thus, the objectives of this study were: to estimate the lethal concentration (LC(I)50;96h); classify and evaluate water quality during testing of the following surfactants: Agral[registered trademark], Aterbane[registered trademark]BR, Ag-bem[registered trademark], Energic[registered trademark], Fixade[registered trademark] and Gotafix[registered trademark] for jewel tetra (Hyphessobrycon eques); and the signs of intoxication in the animals. For this, the fish were acclimated for ten days in the bioassay room. The animals were exposed to the surfactants in an entirely randomized design with three replications. The LC(I)(50;96h) of surfactant Agral[registered trademark] was 3.29 mg L-1; Aterbane[registered trademark] BR 8.21 mg L-1; Energic[registered trademark] 2.34 mg L-1; Gotafix[registered trademark] 4.37 mg L-1; Fixade[registered trademark] 3.38 mg L-1; and Ag-bem[registered trademark] 34.95 mg L-1. The variables of water quality were unchanged. The fish showed an increase in the opercular beating after exposure; 4 and 24 hours, loss of gasping ability; 48 hours, slow opercular beating; and 72 and 96 hours later, recovery. The surfactants Energic[registered trademark], Agral[registered trademark], Gotafix[registered trademark], Aterbane[registered trademark] BR and Fixade[registered trademark] can be classified as moderately toxics, and Ag-Bem[registered trademark] as slightly toxic for H. eques; this organism shows similar intoxication signs for all surfactants.

EFEITO DE SURFACTANTES NA ESTABILIDADE DE COMPOSTOS DE USO TERAPEUTICO

A critical revision of literature as regards to the drug stability in the presence of surfactants were realized. The functional groups envolved in the drug decomposition were used to the development of the discussion. The analysis indicated that the detergent effect can be used to control the rates and mechanisms of drug decomposition and to obtain specific information about the drug reactivity in the environment of pharmacological action.

Effect of micelles, microemulsions and other supramolecular aggregates on the hydrolysis of β-lactam antibiotics

A critical revision of the literature was made regarding the stability of β-lactam antibiotics in the presence of surfactants. The factors involved in the drug decomposition were analyzed in the development of the discussion. The analysis has indicated that some organized systems obtained from surfactants can be used to control rates and mechanisms of antibiotic decomposition. These organized systems can also be used to obtain specific information about the drug reactivity in a microenvironment similar to the site of pharmacological effect.

Different doses of exogenous surfactant for treatment of meconium aspiration syndrome in newborn rabbits.

OBJECTIVE: To evaluate the effects of 2 different doses of exogenous surfactant on pulmonary mechanics and on the regularity of pulmonary parenchyma inflation in newborn rabbits. METHOD: Newborn rabbits were submitted to tracheostomy and randomized into 4 study groups: the Control group did not receive any material inside the trachea; the MEC group was instilled with meconium, without surfactant treatment; the S100 and S200 groups were instilled with meconium and were treated with 100 and 200 mg/kg of exogenous surfactant (produced by Instituto Butantan) respectively. Animals from the 4 groups were mechanically ventilated during a 25-minute period. Dynamic compliance, ventilatory pressure, tidal volume, and maximum lung volume (P-V curve) were evaluated. Histological analysis was conducted using the mean linear intercept (Lm), and the lung tissue distortion index (SDI) was derived from the standard deviation of the means of the Lm. One-way analysis of variance was used with a = 0.05. RESULTS: After 25 minutes of ventilation, dynamic compliance (mL/cm H2O.kg) was 0.87 +/- 0.07 (Control); 0.49 +/- 0.04 (MEC*); 0.67 +/- 0.06 (S100); and 0.67 +/- 0.08 (S200), and ventilatory pressure (cm H2O) was 9.0 +/- 0.9 (Control); 16.5 +/- 1.7 (MEC*); 12.4 +/- 1.1 (S100); and 12.1 +/- 1.5 (S200). Both treated groups had lower Lm values and more homogeneity in the lung parenchyma compared to the MEC group: SDI = 7.5 +/- 1.9 (Control); 11.3 +/- 2.5 (MEC*), 5.8 +/- 1.9 (S100); and 6.7 +/- 1.7 (S200) (*P < 0.05 versus all the other groups). CONCLUSIONS: Animals treated with surfactant showed significant improvement in pulmonary mechanics and more regularity of the lung parenchyma in comparison to untreated animals. There was no difference in results after treatment with either of the doses used.

On the specific filtration mechanism of a mesoporous silica membrane, prepared with non-connecting parallel pores

We report the singular filtration properties of an ultrafiltration membrane made with mesoporous silica that exhibits cylindrical pores aligned mostly normal to the support. This membrane supported on tubular commercial macroporous alumina supports was prepared by the interfacial growth mechanism between stable silica-surfactant hybrid micelles made of the association of silica oligomers with polyethyleneoxide-based (PEO) surfactants and sodium fluoride, a well-known silica condensation catalyst [Boissière et al., An ultrafiltration membrane made with mesoporous MSU-X silica, Chem. Mater. 15 (2003) 460-463]. It appears that the combined effect of the silica nature of the membrane, whose surface charge can be easily adjusted by changing the pH and the non-connected cylindrical shape of the pores provides a new behavior in the retention properties, as proved by the filtration of polyoxyethylene polymers (PEO) with different molecular weights. Depending on the filtration conditions, a rejection rate of 80% and a steep cut-off at 2000 Da can be obtained or, on the reverse, polymers three times bigger than the pore diameter can diffuse through the membrane. This new filtration mechanism, which opens up new modes of separation modes, is explained in the light of both topology of the porous network and pH-dependent interactions between PEO polymers and silica porous media. © 2004 Elsevier B.V. All rights reserved.

An ultrafiltration membrane, prepared with MSU-type mesoporous silica: Preparation and specific filtration behavior

We report preparation and the singular filtration properties of an ultrafiltration membrane made with MSU-type mesoporous silica that exhibits cylindrical pores aligned mostly normal to the support. This membrane supported on tubular commercial macroporous alumina supports was prepared by the interfacial growth mechanism between stable silica-surfactant hybrid micelles made of the association of silica oligomers with polyethyleneoxide-based (PEO) surfactants and sodium fluoride, a well-known silica condensation catalyst. It appears that the combined effect of the silica nature of the membrane, whose surface charge can be easily adjusted by changing the pH and the non-connected cylindrical shape of the pores provides a new behavior in the retention properties, as proved by the filtration of polyoxyethylene polymers (PEO) with different molecular weights. Depending on the filtration conditions, a rejection rate of 80 % and a steep cut-off at 2,000 Da can be obtained or, on the reverse, polymers three times bigger than the pore diameter can diffuse through the membrane. This new filtration mechanism, which opens up new modes of separation modes, is explained in the light of both topology of the porous network and pH-dependent interactions between PEO polymers and silica porous media. © 2005 Elsevier B.V. All rights reserved.

Liposomes and micro/nanoparticles as colloidal carriers for nasal drug delivery

The use of the nasal route for drug delivery has attracted much interest in recent years in the pharmaceutical field. Local and principally systemic drug delivery can be achieved by this route of administration. But the nasal route of delivery is not applicable to all drugs. Polar drugs and some macromolecules are not absorbed in sufficient concentration due to poor membrane permeability, rapid clearance and enzymatic degradation into the nasal cavity. Thus, alternative means that help overcome these nasal barriers are currently in development. Absorption enhancers such as phospholipids and surfactants are constantly used, but care must be taken in relation to their concentration. Drug delivery systems including liposomes, cyclodextrins, micro- and nanoparticles are being investigated to increase the bioavailability of drugs delivered intranasally. This review article discusses recent progress and specific development issues relating to colloidal drug delivery systems in nasal drug delivery. © 2006 Bentham Science Publishers Ltd.

Microemulsão: Um promissor carreador para moléculas insolúveis

Microemulsions (ME) are thermodynamically stable and isotropic systems of two immiscible liquids (oil/water), stabilized by an interfacial film of surfactants, discovered by Hoar and Schulman in 1943. The study of ME formation is based on three areas of theory: (1) solubilization, (2) interfacial tension and (3) thermodynamics. ME structures are influenced by the physicochemical properties and proportions of their ingredients. The goal of this review is to assess the state of the art of microemulsified systems, from a theoretical viewpoint. Also, recent progress on their clinical application and use as carriers for insoluble compounds is discussed.

Dispersing carbon nanotubes in phenolic resin using an aqueous solution

The ability to control the carbon nanotube (CNT) dispersion in polymers is considered the key to most applications of nanotube/polymer composites. The carbon nanotube dispersion into water with different surfactants, as well as its incorporation into phenolic resins, was investigated. Ultrasonication of liquid suspensions was used to prepare stable dispersions. In order to evaluate the best surfactant to be used, light scattering and UV-Visible spectroscopy were employed. The structure of CNT reinforced of phenolic resin was analyzed in function of the concentration and type of surfactant, sonication power and time. It was also evaluated the influence in the dispersion by using the glass temperature transition properties being obtained by dynamic mechanical analyses and impact energy. © 2011 Sociedade Brasileira de Química.

Purification, characterization, and specificity determination of a new serine protease secreted by penicillium waksmanii

The purpose of this work was to purify a protease from Penicillium waksmanii and to determine its biochemical characteristics and specificity. The extracellular protease isolated that was produced by P. waksmanii is a serine protease that is essential for the reproduction and growth of the fungus. The protease isolated showed 32 kDa, and has optimal activity at pH 8.0 and 35 C towards the substrate Abz-KLRSSKQ-EDDnp. The protease is active in the presence of CaCl2, KCl, and BaCl, and partially inhibited by CuCl2, CoCl2 and totally inhibited by AlCl3 and LiCl. In the presence of 1 M urea, the protease remains 50 % active. The activity of the protease increases 60 % when it is exposed to 0.4 % nonionic surfactant-Triton X-100 and loses 10 % activity in the presence of 0.4 % Tween-80. Using fluorescence resonance energy transfer analysis, the protease showed the most specificity for the peptide Abz-KIRSSKQ-EDDnp with k cat/K m of 10,666 mM-1 s-1, followed by the peptide Abz-GLRSSKQ-EDDnp with a k cat/K m of 7,500 mM -1 s-1. Basic and acidic side chain-containing amino acids performed best at subsite S1. Subsites S2, S3, S′ 2, and S′ 1, S ′ 3 showed a preference for binding for amino acids with hydrophobic and basic amino acid side chain, respectively. High values of k cat/K m were observed for the subsites S2, S3, and S′ 2. The sequence of the N-terminus (ANVVQSNVPSWGLARLSSKKTGTTDYTYD) showed high similarity to the fungi Penicillium citrinum and Penicillium chrysogenum, with 89 % of identity at the amino acid level. © 2012 Springer Science+Business Media New York.

Nanostructured materials based on mesoporous silica and mesoporous silica/apatite as osteogenic growth peptide carriers

The aim of this work was the preparation of inorganic mesoporous materials from silica, calcium phosphate and a nonionic surfactant and to evaluate the incorporation and release of different concentrations of osteogenic growth peptide (OGP) for application in bone regeneration. The adsorption and release of the labeled peptide with 5,6-carboxyfluorescein (OGP-CF) from the mesoporous matrix was monitored by fluorescence spectroscopy. The specific surface area was 880 and 484 m2 g- 1 for pure silica (SiO) and silica/apatite (SiCaP), respectively; the area influenced the percentage of incorporation of the peptide. The release of OGP-CF from the materials in simulated body fluid (SBF) was dependent on the composition of the particles, the amount of incorporated peptide and the degradation of the material. The release of 50% of the peptide content occurred at around 4 and 30 h for SiCaP and SiO, respectively. In conclusion, the materials based on SiO and SiCaP showed in vitro bioactivity and degradation; thus, these materials should be considered as alternative biomaterials for bone regeneration. © 2013 Elsevier B.V.

Matrix Effects on Water Analysis for Alkylphenols Using Solid Phase Extraction Gas Chromatography-Mass Spectrometry

Gas chromatography with mass spectrometry is frequently used for the quantification of many classes of substances, including alkylphenols. Alkylphenol polyethoxylates are nonionic surfactants used in a wide variety of industrial and consumer applications. Alkylphenol polyethoxylates can degrade to alkylphenols, which are endocrine disruptors. In analytical validation procedures, the most common parameters studied are the detection and quantification limits, linearity, and recovery; however, the matrix effects are sometimes neglected. Although some investigators have evaluated matrix effects, there is no consensus on how to evaluate them during method validation. In this study, the matrix effects of alkylphenol polyethoxylates (nonylphenol monoethoxylate, nonylphenol diethoxylate, octylphenol monoethoxylate, octylphenol diethoxylate) and alkylphenols (nonylphenol and octylphenol) were studied using solid phase extraction and gas chromatography-mass spectrometry analysis. For alkylphenol polyethoxylates, the matrix effects ranged from 16 to 4692%, whereas for alkylphenols (nonylphenol and octylphenol), the effects were insignificant. Therefore, constructing an analytical curve in the matrix for alkylphenol polyethoxylates is essential. © 2013 Copyright Taylor and Francis Group, LLC.