Bioconversion of Cellulose to Hydrogen by dark fermentation

Hydrogen is known as a clean energy resource. The biological production of hydrogen has been attracting attention as an environmentally friendly processs that does not consume fossil fuels. Cellulosic plant and waste materials are potential resources for fermentative hydrogen production. Cellulose is a linear biopolymer of glucose molecules, connected by β-1,4-glycosidic bonds. Enzymatic hydrolysis of cellulose requires the presence of cellulase. The present study aimed to investigate the efficiency of acid pretreatment on ruminal fluid in order to enrich H2 producing bacteria consortia to enhance biohydrogen rate and substrate removal efficiency. In this study, fermentative hydrogen producers were enriched on cellulose (2g/L) in a modificated Del Nery medium (DNM) at 37ºC and initial pH 7.0 using rumen fluid (10% v/v) as inoculum. To increase the hydrogen production it was added cellulose (10mL) to the medium. The gas products (mainly H2 and CO2) was analyzed by gas chromatography (Shimadzu GC 2010) using a thermal conductivity detector. The volatile fatty acids and ethanol were also detected by GC using a flame ionization detector. Cellulose degradation was quantified by using the phenolsulfuric acid method. Analysis showed that the biogas produced from the anaerobic fermentation contained only hydrogen and carbon dioxide, without detectable methane after acid pretreatment test. On DNM the hydrogen production started with 4 h (5,3 x 105 mmol H2/L) of incubation, and the maximum H2 concentration was observed with 34 h (7,1 x 106 mmol H2/L) of incubation. During the process, it was observed a predominance of acetic acid and butyric acid as well as a low production of acetone, ethanol and nbutanol in all experimental phases. Butyrate accounted for more than 77% of total. As a result of the accumulation of volatile fatty acids (VFAs), the pH value in anaerobic digestion system was reduced to 4,0. On microscopy analyses there were observed rods with endospores. The batch anaerobic fermentation assays performed on anaerobic mixed inoculum from rumen fluid demonstrated the feasibility of H2 generation utilizing cellulose as substrate. Based on the results, it can be concluded that the acid treatment was efficient to inhibit the methanogenic archaea cells present in rumen fluid. The rumen fluid cells present a potential route in converting renewable biomass such as cellulose into hydrogen energy.

Biological Hydrogen production from environmental sample in tropical countries

The hydrogen gas is regarded as clean and renewable energy source, since it generates only water during combustion when used as fuel. It shows 2.75 times more energy content than any hydrocarbon and it can be converted into electrical, mechanical energy or heat. Inoculum sources have been successfully tested for hydrogen biological production in temperate climate countries as sludge treatment plants sewage, sludge treatment plant wastewater, landfill sample, among others. However, hydrogen biologic production with inoculum from environmental samples such as sediment reservoirs, especially in tropical countries like Brazil, is rarely investigated. Reservoirs and fresh water lake sediment may contain conditions for the survival of a wide variety of microorganisms which use different carbon sources mainly glucose and xylose, in the fermentation. Glucose is an easily biodegradable, present in most of the industrial effluents and can be obtained abundantly from agricultural wastes. A wide variety of wastewater resulting from agriculture, industry and pulp and paper processed from wood may contain xylose in its constitution. Such effluent contains glucose and xylose concentrations of about 2 g/L. In this sense, this work verified hydrogen biological production in anaerobic batch reactor (1L), at 37 ° C, initial pH 5.5, headspace with N2 (100%), Del Nery medium, vitamins and peptone (1 g/L), fed separately with glucose (2g/L) and xylose (2 g/L). The inoculum was taken from environmental sample (sediment reservoir Itupararanga - Ibiúna - SP-Brazil). It was previously purified in serial dilutions at H2 generation (10-5, 10-7, 10-10), and heat treated (90º C - 10 min) later to inhibited the H2 consumers. The maximum H2 generations obtained in both tests were observed at 552 h, as described below. At the reactors fed with glucose and xylose were observed, respectively, 9.1 and 8.6 mmol H2/L, biomass growth (0.2 and 0.2 nm); consumption of sugar concentrations 53.6% (1.1 glucose g/L) and 90.5% (1.8 xylose g/L); acetic acid generation (124.7 mg/L and 82.7 mg/L), butyric acid (134.0 mg/L and 230.4 mg/L) and there wasn’t methane generation in the reactors. Microscopic analysis of biomass in anaerobic reactors showed the predominance of Gram positive rods and rods with endospores, whose morphology is characteristic of H2-generating bacteria, in both tests. These species were selected from the natural environment. In DGGE analysis performed difference were observed between populations from inoculum and in tests. This analysis confirmed that some species of bacteria were selected which remained under the conditions imposed on the experiment. The efficiency of the pre-treatment of inoculum and the imposition of pH 5.5 inhibited methane-producing microorganisms and the consumers of H2. Therefore, the experimental conditions imposed allowed the attainment of bacterial consortium of producer H2 taken from an environmental sample with concentration of xylose and glucose similar to the ones of the industrial effluents.

Comparação de junta soldada aço carbono/ aço inox utilizando como metal de adição aço carbono e aço inox

In contemporary industrial, welding processes are widely used, this is the most important process of joining metals used industrially. The welding can be used to build simple structures, like doors and gates for instance, in the same way can be used in situations of high responsibility, such as the nuclear industry and oil industry. Dissimilar welding is a case of welded joints, is characterized by the junction between different materials, for this case, stainless steel and carbon steel that are widely used in steam lines, power plants, nuclear reactors, petrochemical plants. Because their different mechanical and corrosive properties, the join, stainless steel with carbon steel, not only meets environmental requirements and also reduces cost. By using penetrating liquid tests, macrograph, hardness and tensile test was compared the possibility of replacing the current use of 309 rods as filler metal in dissimilar welding between carbon steel and stainless steel by add-on material carbon steel essentially, in this case E7018 coated electrode was used, but without the coating. After analysis of the results and for comparison, was proposed with some certainty that it is possible to replace the addition of materials, thus leading economy in this process widely used in the modern industry

Análise metalográfica do titânio puro submetido à soldagem laser Nd: YAG e TIG

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Disposição construtiva aplicada em cadeira antropométrica

Disposição construtiva aplicada em cadeira antropométrica. Patente de modelo de utilidade para uma cadeira antropométrica constituída de uma estrutura (1) que sustenta uma pluralidade de instrumentos de medição, sendo que a parte posterior da cadeira é provida de dois instrumentos de medição compostos por duas hastes, sendo uma delas para medida da altura tronco-encefálica (2) e a outra para a medida do assento até a região renal (4), de modo que cada uma dessas hastes possui uma escala numérica, sendo ora interna (3), ora externa (5). O assento (6) da cadeira (1) é composto por um anteparo com uma canaleta interna e dois cursores laterais deslizantes para a direita e para a esquerda, que possuem escala numérica.; O assento é provido de referências métricas sendo uma no sentido da largura do assento (8) e outra no sentido da profundidade do assento (9), sendo a escala (8) dividida em duas escalas, onde o ponto zero é exatamente o meio do assento. O assento (6) também possui acoplada uma haste frontal, com deslizamento no sentido antero-posterior (10), a qual contém uma escala interna embutida na peça, de modo que a soma entre a medida da profundidade do assento com a medida obtida pela haste deslizante horizontal (10) totalizam a medida sacro-poplítea. Para a tomada da medida da altura poplítea, há uma outra haste (11), integrada à superfície anterior da cadeira, cujo deslizamento é vertical, sendo que essa haste (11) possui uma escala numérica interna uma externa (12).; A base da cadeira (13) possui um dispositivo de acionamento lateral com o pé (16), que é conectado ao assento (6) por meio de um macaco hidráulico, permitindo a elevação do assento, sendo que a outra alavanca (17), ao ser girada, realiza a descida do assento (6).

Toxicidade do cloridrato de doxorrubicina na dose de 120mg/m², em cadelas com tumor venéreo transmissível

Pós-graduação em Cirurgia Veterinária - FCAV

Orange pectin mediated growth and stability of aqueous gold and silver nanocolloids

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Identification and characterization of regions of difference between the Salmonella Gallinarum biovar Gallinarum and the Salmonella Gallinarum biovar Pullorum genomes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Bacterial diversity from environmental sample applied to bio-hydrogen production

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Resistance to tetracycline and β-lactams and distribution of resistance markers in enteric microorganisms and pseudomonads isolated from the oral cavity

This study evaluated the occurrence of enteric bacteria and pseudomonads resistant to tetracycline and beta-lactams in the oral cavity of patients exhibiting gingivitis (n=89); periodontitis (n=79), periodontally healthy (n=50) and wearing complete dentures (n=41). Microbial identification and presence of resistance markers associated with the production of beta-lactamases and tetracycline resistance were performed by using biochemical tests and PCR. Susceptibility tests were carried out in 201 isolates of enteric cocci and rods. Resistance to ampicillin, amoxicillin/clavulanic acid, imipenem, meropenem and tetracycline was detected in 57.4%, 34.6%, 2.4%, 1.9% and 36.5% of the isolates, respectively. beta-lactamase production was observed in 41.2% of tested microorganisms, while the most commonly found beta-lactamase genetic determinant was gene bla(TEM). Tetracycline resistance was disseminated and a wide scope of tet genes were detected in all studied microbial genus.

Evaluation of the bleached human enamel by scanning electron microscopy

Since bleaching has become a popular procedure, the effect of peroxides on dental hard tissues is of great interest in research. Purpose: The aim of this in vitro study was to perform a qualitative analysis of the human enamel after the application of in-office bleaching agents, using Scanning Electron Microscopy (SEM). Materials and Methods: Twenty intact human third molars extracted for orthodontic reasons were randomly divided into four groups (n=5) treated as follows: G1- storage in artificial saliva (control group); G2- four 30-minute applications of 35% carbamide peroxide (total exposure: 2h); G3- four 2-hour exposures to 35% carbamide peroxide (total exposure: 8h); G4- two applications of 35% hydrogen peroxide, which was light-activated with halogen lamp at 700mW/cm2 during 7min and remained in contact with enamel for 20min (total exposure: 40min). All bleaching treatments adopted in this study followed the application protocols advised by manufacturers. Evaluation of groups submitted to 35% carbamide peroxide was carried out after two time intervals (30 minutes and 2 hours per session), following the extreme situations recommended by the manufacturer. Specimens were prepared for SEM analysis performing gold sputter coating under vacuum and were examined using 15kV at 500x and 2000x magnification. Results: Morphological alterations on the enamel surface were similarly detected after bleaching with either 35% carbamide peroxide or 35% hydrogen peroxide. Surface porosities were characteristic of an erosive process that took place on human enamel. Depression areas, including the formation of craters, and exposure of enamel rods could also be detected. Conclusion: Bleaching effects on enamel morphology were randomly distributed throughout enamel surface and various degrees of enamel damage could be noticed. Clinical significance: In-office bleaching materials may adversely affect enamel morphology and therefore should be used with caution.

The effect of self-adhesive and self-etching resin cements on the bond strength of nonmetallic posts in different root thirds

The purpose of this study was to evaluate the effect of self-adhesive and self-etching resin cements on the bond strength of nonmetallic posts in different root regions. Sixty single-rooted human teeth were decoronated, endodontically treated, post-space prepared, and divided into six groups. Glass-fiber (GF) posts (Exacto, Angelus) and fiber-reinforced composite (FRC) posts (EverStick, StickTeck) were cemented with self-adhesive resin cement (Breeze) (SA) (Pentral Clinical) and self-etching resin cement (Panavia-F) (SE) (Kuraray). Six 1-mm-thick rods were obtained from the cervical (C), middle (M), and apical (A) regions of the roots. The specimens were then subjected to microtensile testing in a special machine (BISCO; Schaumburg, IL, USA) at a crosshead speed of 0.5 mm/min. Microtensile bond strength data were analyzed with two-way ANOVA and Tukey's tests. Means (and SD) of the MPa were: GF/SA/C: 14.32 (2.84), GF/SA/M: 10.69 (2.72), GF/SA/A: 6.77 (2.17), GF/SE/C: 11.56 (4.13), GF/SE/M: 6.49 (2.54), GF/SE/A: 3.60 (1.29), FRC/SA/C: 16.89 (2.66), FRC/SA/M: 13.18 (2.19), FRC/SA/A: 8.45 (1.77), FRC/SE/C: 13.69 (3.26), FRC/SE/M: 9.58 (2.23), FRC/SE/A: 5.62 (2.12). The difference among the regions was statistically significant for all groups (p < 0.05). The self-adhesive resin cement showed better results than the self-etching resin cement when compared to each post (p < 0.05). No statistically significant differences in bond strengths of the resin cements when comparable to each post (p > 0.05). The bond strength values were significantly affected by the resin cement and the highest values were found for self-adhesive resin cement.

Polymerization kinetics and polymerization stress in resin composites after accelerated aging as a function of the expiration date

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evidence-based medicine: an update on treatments for peritoneal dialysis-related peritonitis

Peritonitis continues to be a major complication of peritoneal dialysis (PD), and adequate treatment is crucial for a favorable outcome. There is no consensus regarding the optimal therapeutic regimen, and few prospective controlled studies have been published. The objective of this manuscript is to review the results of PD peritonitis treatment reported in narrative reviews, systematic reviews, and proportional meta-analyses. Two narrative reviews, the only existing systematic review and its update published between 1991 and 2014 were included. In addition, we reported the results of a proportional meta-analysis published by our group. Results from systematic reviews of randomized control trials (RCT) and quasi-RCT were not able to identify any optimal antimicrobial treatment, but glycopeptide regimens were more likely to achieve a complete cure than a first generation cephalosporin. Compared to urokinase, simultaneous catheter removal and replacement resulted in better outcomes. Continuous and intermittent IP antibiotic use had similar outcomes. Intraperitoneal antibiotics were superior to intravenous antibiotics in reducing treatment failure. In the proportional meta-analysis of RCTs and the case series, the resolution rate (86%) of ceftazidime plus glycopeptide as initial treatment was significantly higher than first generation cephalosporin plus aminoglycosides (66%) and glycopeptides plus aminoglycosides (75%). Other comparisons of regimens used for either initial treatment or treatment of gram-positive rods or gram-negative rods did not show statistically significant differences. The superiority of a combination of a glycopeptide and a third generation cephalosporin was also reported by a narrative review study published in 1991, which reported an 88% resolution rate.

Antibioticoterapia para o tratamento de periotonite em diálise peritoneal: redicão sostemática de estudo clínicos controlados e série de casos

Pós-graduação em Fisiopatologia em Clínica Médica - FMB