Transmission Electron Microscopy Characterization of Laser Welding Cast Ni-Based Superalloy K418 Turbo Disk And Alloy Steel 42Crmo Shaft

Microstructure characterization is important for controlling the quality of laser welding. In the present work, a detailed microstructure characterization by transmission electron microscopy was carried out on the laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft and an unambiguous identification of phases in the weldment was accomplished. It was found that there are gamma-FeCrNiC austenite solid solution dendrites as the matrix, (Nb, Ti) C type MC carbides, fine and dispersed Ni-3 Al gamma' phase as well as Laves particles in the interdendritic region of the seam zone. A brief discussion was given for their existence based on both kinetic and thermodynamic principles. (c) 2007 Elsevier B.V. All rights reserved.

Research on laser welding of cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft

Exploratory experiments of laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft were conducted. Microstructure of the welded seam was characterized by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy-dispersive spectrometer (EDS). Mechanical properties of the welded seam were evaluated by microhardness and tensile strength testing. The corresponding mechanisms were discussed in detail. Results showed that the laser-welded seam had non-equilibrium solidified microstructures consisting of FeCr0.29Ni0.16C0.06 austenite solid solution dendrites as the dominant and some fine and dispersed Ni3Al gamma' phase and Laves particles as well as little amount of MC short stick or particle-like carbides distributed in the interdendritic regions. The average microhardness of the welded seam was relatively uniform and lower than that of the base metal due to partial dissolution and suppression of the strengthening phase gamma' to some extent. About 88.5% tensile strength of the base metal was achieved in the welded joint because of a non-full penetration welding and the fracture mechanism was a mixture of ductility and brittleness. The existence of some Laves particles in the welded seam also facilitated the initiation and propagation of the microcracks and microvoids and hence, the detrimental effects of the tensile strength of the welded joint. The present results stimulate further investigation on this field. (c) 2006 Elsevier B.V. All rights reserved.

Effect of Surface Condition of Electrode on the Surface Melting of Material by Laser-Guided Micro-Arc Discharge

This paper studies the surface melting in the atmosphere by YAG laser-guided micro-arc discharge. In three kinds of surface conditions (free, oiled, and polyethylene covered), we try to control the diameter and the power density of discharge pit. It is found that the power density of 3 x 10(6) W/cm(2) of discharge pit on the oiled surface is moderate to form the melted layer thicker than that of the others, adapting to strengthen the surface of material, and the power density of 1.07 x 10(7) W/cm(2) of discharge pit on the polyethylene-covered surface is highest to form the deepest discharge pit among them, adapting to remove the material.

Diagnóstico de la brucelosis bovina por el método del "ring-test"

El presente trabajo se llevó a cabo entre los meses de Julio a Septiembre del año 1965, en los Laboratorios de la Escuela Nacional de Agricultura y Ganadería. Se recurrió a la prueba del Ring-Test, para diagnosticar la Brucelosis en hatos situados en los departamentos de Managua, León, Carazo, Masaya, Granada, Rivas y Boaco; se obtuvieron ciertos datos estadísticos al objeto de hacer un estudio de productividad de leche. Los resultados de este trabajo fueron: 1). Las fincas positivas se encuentran localizadas en los departamentos de Managua, Carazo, Granada y Rivas. 2). Los porcentajes de hatos Negativos, positivos y sospechosos por departamento fueron los siguientes: % de hatos N., Managua 80,76. % de hatos P. 9.62, % de hatos S. 3.91, Leon % de hatos N. 100.00, % de hatos P. 9.62, % de hatos S. 0, Granada % de hatos N. 86.66, % de Hatos P. 0, % de hatos S. 0, Rivas % de hatos N. 46.15, % de hatos P. 53.85, % de hatos S. 0. No se hace mención de los porcentajes de los departamentos de Masaya, Carazo y Boaco, debido a los pocos hatos examinados en ellos. 3). El porcentaje de vacas en producción del total de vacas adultas es de 54.10% en la cuenca lechera y la zona del pacifico y el 54% en los hatos examinados. 4). La cantidad de leche para la venta es de 3.22 litros por vaca.