Integrating on-line process control and imperfect corrective maintenance: An economical design

Existing studies of on-line process control are concerned with economic aspects, and the parameters of the processes are optimized with respect to the average cost per item produced. However, an equally important dimension is the adoption of an efficient maintenance policy. In most cases, only the frequency of the corrective adjustment is evaluated because it is assumed that the equipment becomes "as good as new" after corrective maintenance. For this condition to be met, a sophisticated and detailed corrective adjustment system needs to be employed. The aim of this paper is to propose an integrated economic model incorporating the following two dimensions: on-line process control and a corrective maintenance program. Both performances are objects of an average cost per item minimization. Adjustments are based on the location of the measurement of a quality characteristic of interest in a three decision zone. Numerical examples are illustrated in the proposal. (c) 2012 Elsevier B.V. All rights reserved.

Automated system of seedling image analysis (SVIS) and electrical conductivity to assess sun hemp seed vigor

The development of new procedures for quickly obtaining accurate information on the physiological potential of seed lots is essential for developing quality control programs for the seed industry. In this study, the effectiveness of an automated system of seedling image analysis (Seed Vigor Imaging System - SVIS) in determining the physiological potential of sun hemp seeds and its relationship with electrical conductivity tests, were evaluated. SVIS evaluations were performed three and four days after sowing and data on the vigor index and the length and uniformity of seedling growth were collected. The electrical conductivity test was made on 50 seed replicates placed in containers with 75 mL of deionised water at 25 ºC and readings were taken after 1, 2, 4, 8 and 16 hours of imbibition. Electrical conductivity measurements at 4 or 8 hours and the use of the SVIS on 3-day old seedlings can effectively detect differences in vigor between different sun hemp seed lots.

Assessment of physiological potential of cucumber seeds using the software Seedling Vigor Imaging System® (SVIS®)

The software Seed Vigor Imaging System (SVIS®), has been successfully used to evaluate seed physiological potential by automated analyses of scanned seedlings. In this research, the efficiency of this system was compared to other tests accepted for assessing cucumber (Cucumis sativus L.) seed vigor of distinct seed lots of Supremo and Safira cultivars. Seeds were subjected to germination, traditional and saturated salt accelerated aging, seedling emergence, seedling length and SVIS analyses (determination of vigor indices and seedling growth uniformity, lengths of primary root, hypocotyl and whole seedlings). It was also determined whether the definition of seedling growth/uniformity ratios affects the sensitivity of the SVIS®. Results showed that analyses SVIS have provided consistent identification of seed lots performance, and have produced information comparable to those from recommended seed vigor tests, thus demonstrating a suitable sensitivity for a rapid and objective evaluation of physiological potential of cucumber seeds. Analyses of four-days-old cucumber seedlings using the SVIS® are more accurate and growth/uniformity does not affect the precision of results.

Architectures and design patterns for functional design of logic control and diagnostics in industrial automation

Recently in most of the industrial automation process an ever increasing degree of automation has been observed. This increasing is motivated by the higher requirement of systems with great performance in terms of quality of products/services generated, productivity, efficiency and low costs in the design, realization and maintenance. This trend in the growth of complex automation systems is rapidly spreading over automated manufacturing systems (AMS), where the integration of the mechanical and electronic technology, typical of the Mechatronics, is merging with other technologies such as Informatics and the communication networks. An AMS is a very complex system that can be thought constituted by a set of flexible working stations, one or more transportation systems. To understand how this machine are important in our society let considerate that every day most of us use bottles of water or soda, buy product in box like food or cigarets and so on. Another important consideration from its complexity derive from the fact that the the consortium of machine producers has estimated around 350 types of manufacturing machine. A large number of manufacturing machine industry are presented in Italy and notably packaging machine industry,in particular a great concentration of this kind of industry is located in Bologna area; for this reason the Bologna area is called “packaging valley”. Usually, the various parts of the AMS interact among them in a concurrent and asynchronous way, and coordinate the parts of the machine to obtain a desiderated overall behaviour is an hard task. Often, this is the case in large scale systems, organized in a modular and distributed manner. Even if the success of a modern AMS from a functional and behavioural point of view is still to attribute to the design choices operated in the definition of the mechanical structure and electrical electronic architecture, the system that governs the control of the plant is becoming crucial, because of the large number of duties associated to it. Apart from the activity inherent to the automation of themachine cycles, the supervisory system is called to perform other main functions such as: emulating the behaviour of traditional mechanical members thus allowing a drastic constructive simplification of the machine and a crucial functional flexibility; dynamically adapting the control strategies according to the different productive needs and to the different operational scenarios; obtaining a high quality of the final product through the verification of the correctness of the processing; addressing the operator devoted to themachine to promptly and carefully take the actions devoted to establish or restore the optimal operating conditions; managing in real time information on diagnostics, as a support of the maintenance operations of the machine. The kind of facilities that designers can directly find on themarket, in terms of software component libraries provides in fact an adequate support as regard the implementation of either top-level or bottom-level functionalities, typically pertaining to the domains of user-friendly HMIs, closed-loop regulation and motion control, fieldbus-based interconnection of remote smart devices. What is still lacking is a reference framework comprising a comprehensive set of highly reusable logic control components that, focussing on the cross-cutting functionalities characterizing the automation domain, may help the designers in the process of modelling and structuring their applications according to the specific needs. Historically, the design and verification process for complex automated industrial systems is performed in empirical way, without a clear distinction between functional and technological-implementation concepts and without a systematic method to organically deal with the complete system. Traditionally, in the field of analog and digital control design and verification through formal and simulation tools have been adopted since a long time ago, at least for multivariable and/or nonlinear controllers for complex time-driven dynamics as in the fields of vehicles, aircrafts, robots, electric drives and complex power electronics equipments. Moving to the field of logic control, typical for industrial manufacturing automation, the design and verification process is approached in a completely different way, usually very “unstructured”. No clear distinction between functions and implementations, between functional architectures and technological architectures and platforms is considered. Probably this difference is due to the different “dynamical framework”of logic control with respect to analog/digital control. As a matter of facts, in logic control discrete-events dynamics replace time-driven dynamics; hence most of the formal and mathematical tools of analog/digital control cannot be directly migrated to logic control to enlighten the distinction between functions and implementations. In addition, in the common view of application technicians, logic control design is strictly connected to the adopted implementation technology (relays in the past, software nowadays), leading again to a deep confusion among functional view and technological view. In Industrial automation software engineering, concepts as modularity, encapsulation, composability and reusability are strongly emphasized and profitably realized in the so-calledobject-oriented methodologies. Industrial automation is receiving lately this approach, as testified by some IEC standards IEC 611313, IEC 61499 which have been considered in commercial products only recently. On the other hand, in the scientific and technical literature many contributions have been already proposed to establish a suitable modelling framework for industrial automation. During last years it was possible to note a considerable growth in the exploitation of innovative concepts and technologies from ICT world in industrial automation systems. For what concerns the logic control design, Model Based Design (MBD) is being imported in industrial automation from software engineering field. Another key-point in industrial automated systems is the growth of requirements in terms of availability, reliability and safety for technological systems. In other words, the control system should not only deal with the nominal behaviour, but should also deal with other important duties, such as diagnosis and faults isolations, recovery and safety management. Indeed, together with high performance, in complex systems fault occurrences increase. This is a consequence of the fact that, as it typically occurs in reliable mechatronic systems, in complex systems such as AMS, together with reliable mechanical elements, an increasing number of electronic devices are also present, that are more vulnerable by their own nature. The diagnosis problem and the faults isolation in a generic dynamical system consists in the design of an elaboration unit that, appropriately processing the inputs and outputs of the dynamical system, is also capable of detecting incipient faults on the plant devices, reconfiguring the control system so as to guarantee satisfactory performance. The designer should be able to formally verify the product, certifying that, in its final implementation, it will perform itsrequired function guarantying the desired level of reliability and safety; the next step is that of preventing faults and eventually reconfiguring the control system so that faults are tolerated. On this topic an important improvement to formal verification of logic control, fault diagnosis and fault tolerant control results derive from Discrete Event Systems theory. The aimof this work is to define a design pattern and a control architecture to help the designer of control logic in industrial automated systems. The work starts with a brief discussion on main characteristics and description of industrial automated systems on Chapter 1. In Chapter 2 a survey on the state of the software engineering paradigm applied to industrial automation is discussed. Chapter 3 presentes a architecture for industrial automated systems based on the new concept of Generalized Actuator showing its benefits, while in Chapter 4 this architecture is refined using a novel entity, the Generalized Device in order to have a better reusability and modularity of the control logic. In Chapter 5 a new approach will be present based on Discrete Event Systems for the problemof software formal verification and an active fault tolerant control architecture using online diagnostic. Finally conclusive remarks and some ideas on new directions to explore are given. In Appendix A are briefly reported some concepts and results about Discrete Event Systems which should help the reader in understanding some crucial points in chapter 5; while in Appendix B an overview on the experimental testbed of the Laboratory of Automation of University of Bologna, is reported to validated the approach presented in chapter 3, chapter 4 and chapter 5. In Appendix C some components model used in chapter 5 for formal verification are reported.

Development of a microgrid with renewable energy sources and electrochemical storage system integration

Beside the traditional paradigm of "centralized" power generation, a new concept of "distributed" generation is emerging, in which the same user becomes pro-sumer. During this transition, the Energy Storage Systems (ESS) can provide multiple services and features, which are necessary for a higher quality of the electrical system and for the optimization of non-programmable Renewable Energy Source (RES) power plants. A ESS prototype was designed, developed and integrated into a renewable energy production system in order to create a smart microgrid and consequently manage in an efficient and intelligent way the energy flow as a function of the power demand. The produced energy can be introduced into the grid, supplied to the load directly or stored in batteries. The microgrid is composed by a 7 kW wind turbine (WT) and a 17 kW photovoltaic (PV) plant are part of. The load is given by electrical utilities of a cheese factory. The ESS is composed by the following two subsystems, a Battery Energy Storage System (BESS) and a Power Control System (PCS). With the aim of sizing the ESS, a Remote Grid Analyzer (RGA) was designed, realized and connected to the wind turbine, photovoltaic plant and the switchboard. Afterwards, different electrochemical storage technologies were studied, and taking into account the load requirements present in the cheese factory, the most suitable solution was identified in the high temperatures salt Na-NiCl2 battery technology. The data acquisition from all electrical utilities provided a detailed load analysis, indicating the optimal storage size equal to a 30 kW battery system. Moreover a container was designed and realized to locate the BESS and PCS, meeting all the requirements and safety conditions. Furthermore, a smart control system was implemented in order to handle the different applications of the ESS, such as peak shaving or load levelling.

Die Regulation der Ubiquitinligase CHIP durch das Cochaperon BAG2 im zellulären System und im Kontext der replikativen Seneszenz

Eine funktionierende Proteinqualitätskontrolle ist essenziell für die Vitalität einer Zelle. Das dynamische Gleichgewicht zwischen Proteinfaltung und -degradation wird von molekularen Chaperonen aufrechterhalten, deren Aktivität wiederum durch die Interaktion mit zahlreichen Cochaperonen moduliert wird. Das Cochaperon CHIP ist ein zentraler Faktor in Proteintriage-Entscheidungsprozessen, da es als Ubiquitinligase Chaperonsubstrate dem Abbau zuführt und somit die Chaperonmaschinerie direkt mit den Systemen der Proteindegradation verbindet. Um Polypeptide vor einem vorzeitigen Abbau zu schützen, wird die destruktive Aktivität von CHIP durch weitere Cochaperone reguliert. rnIn dieser Arbeit konnte die Hemmung der Ligaseaktivität von CHIP durch das Cochaperon BAG2 mechanistisch erstmals in einem zellulären System nachgewiesen werden. Dazu wurde die humane IMR-90 Fibroblasten Zelllinie verwendet. Die Ubiquitinierungsaktivität von CHIP wurde anhand von HSP72 als Modell-CHIP-Substrat untersucht. Durch die verringerte Ubiquitinierung, und damit dem reduzierten Abbau von HSP72, regulierte BAG2 dessen intrazelluläre Proteinspiegel, ohne dabei selbst eine Hitzeschockantwort zu induzieren. Überexprimiertes BAG2 wirkte sich trotz stabilisierter HSP72-Spiegel bei einem appliziertem Hitzestresses negativ auf die Zellvitalität aus, vermutlich da BAG2 durch die Inhibition von CHIP-vermittelter Ubiquitinierung massiv in das Gleichgewicht zwischen Substratfaltung und -degradation eingreift.rnDa sich die Mechanismen der Proteinqualitätskontrolle in der Alterung stark verändern und sich den wandelnden Bedingungen in der Zelle anpassen, wurde in einem zweiten Teil dieser Arbeit mit Hilfe des IMR-90 Zellsystems als etabliertes Modell zellulärer Seneszenz analysiert, inwieweit sich die Aktivität und die Regulation von CHIP durch BAG2 in der zellulären Alterung ändern. In seneszenten Zellen war HSP72 erheblich weniger ubiquitiniert als in jungen Fibroblasten, was auf eine reduzierte CHIP-Aktivität hinweist. Diese blieb jedoch durch BAG2 weiterhin modulierbar. Die Funktion von BAG2 als Inhibitor der Ubiquitinligase CHIP blieb demnach in seneszenten Zellen bestehen. In gealterten Fibroblasten regulierte BAG2 außerdem die Proteinspiegel des CHIP-Substrates und Seneszenzinitiators p53, was BAG2 eine mögliche Rolle in der Etablierung des Seneszenz-Phänotyps zuspricht. Weiterhin unterlagen die Proteinspiegel der beiden funktionell redundanten CHIP-Modulatoren BAG2 und HSPBP1 in der zellulären Alterung einer reziproken Regulation. In gealterten Mäusen trat die gegenläufige Veränderung der beiden Cochaperone gewebsspezifisch in der Lunge auf. Außerdem waren die BAG2-Proteinspiegel im Hippocampus gealterter Tiere signifikant erhöht.rnZusammenfassend konnte anhand der erzielten Ergebnisse die Funktion von BAG2 als Inhibitor von CHIP im zellulären System bestätigt werden. Außerdem durchlaufen die Aktivität und die Regulation von CHIP einen seneszenzspezifischen Adaptationsprozess, welcher für die Erhaltung der Proteostase in der Alterung relevant sein könnte und in welchem die Funktion von BAG2 als CHIP-Modulator möglicherweise eine wichtige Rolle spielt.rnZukünftige Studien könnten die komplexen Mechanismen weiterführend aufklären, mit denen CHIP-Aktivität reguliert wird. Dies kann helfen, der altersbedingten Abnahme an proteostatischer Kontrolle entgegenzuwirken und aberrante Proteinaggregation in altersassoziierten Erkrankungen vorzubeugen.rn

Chances and risks of publication of quality data - the perspectives of Swiss physicians and nurses

Background The release of quality data from acute care hospitals to the general public is based on the aim to inform the public, to provide transparency and to foster quality-based competition among providers. Due to the expected mechanisms of action and possibly the adverse consequences of public quality comparison, it is a controversial topic. The perspective of physicians and nurses is of particular importance in this context. They are mainly responsible for the collection of quality-control data, and are directly confronted with the results of public comparison. The research focus of this qualitative study was to discover what the views and opinions of the Swiss physicians and nurses were regarding these issues. It was investigated as to how the two professional groups appraised the opportunities as well as the risks of the release of quality data in Switzerland. Methods A qualitative approach was chosen to answer the research question. For data collection, four focus groups were conducted with physicians and nurses who were employed in Swiss acute care hospitals. Qualitative content analysis was applied to the data. Results The results revealed that both occupational groups had a very critical and negative attitude regarding the recent developments. The perceived risks were dominating their view. In summary, their main concerns were: the reduction of complexity, the one-sided focus on measurable quality variables, risk selection, the threat of data manipulation and the abuse of published information by the media. An additional concern was that the impression is given that the complex construct of quality can be reduced to a few key figures, and it that it is constructed from a false message which then influences society and politics. This critical attitude is associated with the different value system and the professional self-concept that both physicians and nurses have, in comparison to the underlying principles of a market-based economy and the economic orientation of health care business. Conclusions The critical and negative attitude of Swiss physicians and nurses must, under all conditions, be heeded to and investigated regarding its impact on work motivation and identification with the profession. At the same time, the two professional groups are obligated to reflect upon their critical attitude and take a proactive role in the development of appropriate quality indicators for the publication of quality data in Switzerland.

A Measurement System Experiment to Evaluate the Nosing-to-nosing Method for Measuring Dimensions of Steps

Non-uniformity of steps within a flight is a major risk factor for falls. Guidelines and requirements for uniformity of step risers and tread depths assume the measurement system provides precise dimensional values. The state-of-the-art measurement system is a relatively new method, known as the nosing-to-nosing method. It involves measuring the distance between the noses of adjacent steps and the angle formed with the horizontal. From these measurements, the effective riser height and tread depth are calculated. This study was undertaken for the purpose of evaluating the measurement system to determine how much of total measurement variability comes from the step variations versus that due to repeatability and reproducibility (R&R) associated with the measurers. Using an experimental design quality control professionals call a measurement system experiment, two measurers measured all steps in six randomly selected flights, and repeated the process on a subsequent day. After marking each step in a flight in three lateral places (left, center, and right), the measurers took their measurement. This process yielded 774 values of riser height and 672 values of tread depth. Results of applying the Gage R&R ANOVA procedure in Minitab software indicated that the R&R contribution to riser height variability was 1.42%; and to tread depth was 0.50%. All remaining variability was attributed to actual step-to-step differences. These results may be compared with guidelines used in the automobile industry for measurement systems that consider R&R less than 1% as an acceptable measurement system; and R&R between 1% and 9% as acceptable depending on the application, the cost of the measuring device, cost of repair, or other factors.

Distributed Control Nodes for Material Flow System Controls on the Example of Unit Load Conveyor and Sorter Facilities

The Chair of Transportation and Ware-housing at the University of Dortmund together with its industrial partner has developed and implemented a decentralized control system based on embedded technology and Internet standards. This innovative, highly flexible system uses autonomous software modules to control the flow of unit loads in real-time. The system is integrated into Chair’s test facility consisting of a wide range of conveying and sorting equipment. It is built for proof of concept purposes and will be used for further research in the fields of decentralized automation and embedded controls. This presentation describes the implementation of this decentralized control system.

Control estadístico de calidad en bibliotecología : Aplicación de gráficos de control en los procesos técnicos

A partir de la aceptación de la biblioteca como parte del ciclo de creación, organización y diseminación del conocimiento cambió el concepto de la misma de una entidad cerrada hacia un sistema dinámico en constante interacción con su entorno. Así se la reconoció como una institución social más que como una colección de documentos. Desde entonces se percibió a la biblioteca como una entidad en la que se podía aplicar los principios de gestión. Desde entonces se utilizaron distintas herramientas de gestión para la toma de decisiones en el ámbito de las bibliotecas. Entre estas herramientas son de gran importancia en el control estadístico de procesos los gráficos de control, utilizados para medir la estabilidad de un proceso a través del tiempo. Han tenido amplia aplicación en el control estadístico de la calidad, comenzando en el ámbito industrial. Hoy su aplicación se ha extendido a una gran variedad de disciplinas incluyen empresas de servicios y unidades administrativas. Aquí se presentan a los gráficos de control como una importante herramienta de gestión aplicada a los procesos técnicos permitiendo su evaluación y el monitoreo de su desempeño a partir de la utilización de indicadores y otros datos de carácter diagnóstico

Control estadístico de calidad en bibliotecología : Aplicación de gráficos de control en los procesos técnicos

A partir de la aceptación de la biblioteca como parte del ciclo de creación, organización y diseminación del conocimiento cambió el concepto de la misma de una entidad cerrada hacia un sistema dinámico en constante interacción con su entorno. Así se la reconoció como una institución social más que como una colección de documentos. Desde entonces se percibió a la biblioteca como una entidad en la que se podía aplicar los principios de gestión. Desde entonces se utilizaron distintas herramientas de gestión para la toma de decisiones en el ámbito de las bibliotecas. Entre estas herramientas son de gran importancia en el control estadístico de procesos los gráficos de control, utilizados para medir la estabilidad de un proceso a través del tiempo. Han tenido amplia aplicación en el control estadístico de la calidad, comenzando en el ámbito industrial. Hoy su aplicación se ha extendido a una gran variedad de disciplinas incluyen empresas de servicios y unidades administrativas. Aquí se presentan a los gráficos de control como una importante herramienta de gestión aplicada a los procesos técnicos permitiendo su evaluación y el monitoreo de su desempeño a partir de la utilización de indicadores y otros datos de carácter diagnóstico

Control estadístico de calidad en bibliotecología : Aplicación de gráficos de control en los procesos técnicos

A partir de la aceptación de la biblioteca como parte del ciclo de creación, organización y diseminación del conocimiento cambió el concepto de la misma de una entidad cerrada hacia un sistema dinámico en constante interacción con su entorno. Así se la reconoció como una institución social más que como una colección de documentos. Desde entonces se percibió a la biblioteca como una entidad en la que se podía aplicar los principios de gestión. Desde entonces se utilizaron distintas herramientas de gestión para la toma de decisiones en el ámbito de las bibliotecas. Entre estas herramientas son de gran importancia en el control estadístico de procesos los gráficos de control, utilizados para medir la estabilidad de un proceso a través del tiempo. Han tenido amplia aplicación en el control estadístico de la calidad, comenzando en el ámbito industrial. Hoy su aplicación se ha extendido a una gran variedad de disciplinas incluyen empresas de servicios y unidades administrativas. Aquí se presentan a los gráficos de control como una importante herramienta de gestión aplicada a los procesos técnicos permitiendo su evaluación y el monitoreo de su desempeño a partir de la utilización de indicadores y otros datos de carácter diagnóstico

A database of multi-year (2004-2010) quality-assured surface solar hourly irradiation measurements for the Egyptian territory

A database containing the global and diffuse components of the surface solar hourly irradiation measured from 1 January 2004 to 31 December 2010 at eight stations of the Egyptian Meteorological Authority is presented. For three of these sites (Cairo, Aswan, and El-Farafra), the direct component is also available. In addition, a series of meteorological variables including surface pressure, relative humidity, temperature, wind speed and direction is provided at the same hourly resolution at all stations. The details of the experimental sites and instruments used for the acquisition are given. Special attention is paid to the quality of the data and the procedure applied to flag suspicious or erroneous measurements is described in details. Between 88 and 99% of the daytime measurements are validated by this quality control. Except at Barrani where the number is lower (13500), between 20000 and 29000 measurements of global and diffuse hourly irradiation are available at all sites for the 7-year period. Similarly, from 9000 to 13000 measurements of direct hourly irradiation values are provided for the three sites where this component is measured. With its high temporal resolution this consistent irradiation and meteorological database constitutes a reliable source to estimate the potential of solar energy in Egypt. It is also adapted to the study of high-frequency atmospheric processes such as the impact of aerosols on atmospheric radiative transfer. In the next future, it is planned to complete regularly the present 2004-2010 database.

Food quality awareness : cases from shrimp producers in Thailand and vegetable producers in Vietnam

The high number of import rejections of food commodities suggests that producers in exporting countries are not complying with established standards. To understand why this is the case, we explore the behavior of producers and consumers in developing countries. First, we examine the successful transformation of production practices adopted by shrimp producers in Thailand. In support of the dramatic change in practices, we observe an important role played by the public sector in providing a means to visualize chemical residues and to control processes upstream of the supply chain via a registration system and a traceability system called Movement Document. Furthermore, very active information sharing by the private sector contributes to the dissemination of useful technical and market information among producers. We also examine the knowledge and perceptions of consumers with respect to food safety in Vietnam. We find that consumers in Hanoi and Ho Chi Minh City behave differently toward the third-party certification VietGAP, probably owing to differences in the history of market mechanisms between the two cities.

NetCDF based data archiving system applied to ITER Fast Plant System Control prototype

EURATOM/CIEMAT and Technical University of Madrid (UPM) have been involved in the development of a FPSC [1] (Fast Plant System Control) prototype for ITER, based on PXIe (PCI eXtensions for Instrumentation). One of the main focuses of this project has been data acquisition and all the related issues, including scientific data archiving. Additionally, a new data archiving solution has been developed to demonstrate the obtainable performances and possible bottlenecks of scientific data archiving in Fast Plant System Control. The presented system implements a fault tolerant architecture over a GEthernet network where FPSC data are reliably archived on remote, while remaining accessible to be redistributed, within the duration of a pulse. The storing service is supported by a clustering solution to guaranty scalability, so that FPSC management and configuration may be simplified, and a unique view of all archived data provided. All the involved components have been integrated under EPICS [2] (Experimental Physics and Industrial Control System), implementing in each case the necessary extensions, state machines and configuration process variables. The prototyped solution is based on the NetCDF-4 [3] and [4] (Network Common Data Format) file format in order to incorporate important features, such as scientific data models support, huge size files management, platform independent codification, or single-writer/multiple-readers concurrency. In this contribution, a complete description of the above mentioned solution is presented, together with the most relevant results of the tests performed, while focusing in the benefits and limitations of the applied technologies.