New Courthouse at El Ejido

The courthouse at El Ejido has a trapezoid floor plan (47 m × 55/26 m) and comprises two distinct volumes that are structurally connected at the basement level and by the footbridges on the upper storeys. A third trapezoid unit featuring a glazed curtain wall facade cantilevers 8 m off the main facade of the front volume. This facade is a structural diaphragm wall, constituted by nine rows of vertical precast concrete members separated by horizontal cast-in-place, self-compacting concrete chords. The location of the courthouse in a seismic area and the small number of horizontal supports for the facade make this wall potentially vulnerable. The high risk, in particular, during construction required careful planning based on a detailed analysis of the interaction between the structure and the ancillary resources used to build it

Refuerzo de vigas de hormigón armado mediante la aplicación de fuerzas exteriores introducidas por predeformación de perfiles metálicos

Una técnica de refuerzo de elementos flectados en general y, en particular, de vigas y forjados de hormigón armado, consiste en la disposición de perfiles metálicos por debajo de los elementos a reforzar y retacados a ellos. En muchos casos este refuerzo se diseña con un planteamiento pasivo, es decir, los perfiles no entran en carga hasta que no se incrementan las acciones sobre el elemento reforzado, o lo hacen sólo ligeramente y de forma cuantitativamente no controlada efectuando el retacado mediante cuñas metálicas. En el presente trabajo se estudia la alternativa del refuerzo de vigas de hormigón armado frente a momentos flectores con un planteamiento activo, introduciendo unas fuerzas (por ejemplo, mediante gatos o barras roscadas) entre el perfil y el elemento a reforzar, y retacando posteriormente el perfil a la viga en los puntos de introducción de las fuerzas, mediante cuñas metálicas, mortero, etc. La propuesta que formulamos en el presente trabajo de investigación para el control de las fuerzas introducidas consiste en la medida de las flechas que se producen en el perfil metálico al hacerlo reaccionar contra la viga. Esto permite el empleo de procedimientos sencillos para la predeformación del perfil que no dispongan de dispositivos de medida de la carga introducida, o bien controlar la veracidad de las medidas de las fuerzas que dan tales dispositivos. La gran fiabilidad que tiene el cálculo de flechas en jácenas metálicas hace que con este procedimiento se puedan conocer con gran precisión las fuerzas introducidas. Las medidas de las flechas se pueden llevar a cabo mediante los procedimientos de instrumentación habituales en pruebas de carga, con una precisión más que suficiente para conocer y controlar con fiabilidad el valor de las fuerzas que el perfil ejerce sobre la viga. Los perfiles necesarios para el refuerzo con esta técnica son netamente inferiores a los que se precisarían con el planteamiento pasivo antes indicado. En el trabajo de investigación se recoge un estudio sobre el número, posición y valor de las fuerzas de refuerzo a introducir, en función de la carga para la que se diseña el refuerzo y la capacidad resistente del elemento a reforzar, y se analizan los valores máximos que pueden tener dichas fuerzas, en función de la capacidad de la pieza frente a momentos de signo contrario a los debidos a las cargas gravitatorias. A continuación se analiza la interacción viga-perfil al incrementarse las cargas sobre la viga desde el instante de la ejecución del refuerzo, interacción que hace variar el valor de las fuerzas que el perfil ejerce sobre la viga. Esta variación permite contar con un incremento en las fuerzas de refuerzo si, con las cargas permanentes presentes al reforzar, no podemos introducirlas inicialmente con el valor necesario, o si se producen pérdidas en las propias fuerzas. Este es uno de los criterios a la hora de seleccionar las características del perfil. Por el contrario, dicha variación puede suponer que en algunos puntos a lo largo del vano se supere la capacidad a flexión frente a momentos de signo contrario a los debidos a las cargas gravitatorias, lo que también debe ser tenido en cuenta. Seguidamente se analizan diferentes aspectos que producen una variación en el valor de las fuerzas de refuerzo, como son las deformaciones diferidas del hormigón (fluencia y retracción), los gradientes de temperatura en la pieza, o la actuación de sobrecargas en los vanos adyacentes. Se concluye los efectos de estos fenómenos, que en ocasiones tienen gran influencia, pueden ser cuantificados por el proyectista, recogiéndose propuestas sencillas para su consideración en casos habituales. Posteriormente recogemos una propuesta de metodología de comprobación del refuerzo, en cuanto a cómo considerar la fisuración y evolución del módulo de deformación de la viga, la introducción de la seguridad, la influencia de las tolerancias de laminación en el perfil sobre el valor calculado de las flechas necesarias en el perfil para introducir las fuerzas iniciales proyectadas, o la situación accidental de fuego, entre otros aspectos. Por último, se exponen las conclusiones más relevantes de la investigación realizada, y se proponen futuras líneas de investigación. One technique for strengthening flexural members in general, and reinforced concrete beams and slabs in particular, entails caulking the underside of these members with steel shapes. This sort of strengthening is often designed from a passive approach; i.e., until the load is increased, the shapes are either not loaded or are only slightly loaded to some unquantified extent by caulking with steel shims. The present study explored the possibility of actively strengthening the capacity of reinforced concrete beams to resist bending moments by applying forces (with jacks or threaded bars, for instance) between the shape and the member to be strengthened. The shape is subsequently caulked under the beam at the points where the forces are applied with steel shims, mortar or similar. The proposal put forward in the present study to monitor the forces applied consists in measuring the deflection on the steel shape as it reacts against the beam. With this technique, the shape can be pre-strained using simple procedures that do not call for devices to measure the force applied, or the accurancy of the respective measurements can be verified. As deflection calculations in steel girders are extremely reliable, the forces applied with this procedure can be very precisely determined. Standard instrumental procedures for load testing can be used to measure deflection with more than sufficient precision to reliably determine and monitor the value of the forces exerted on the beam by the shape. Moreover, the shapes required to strengthen members with this technique are substantially smaller than the ones needed in the aforementioned passive approach. This study addressed the number, position and value of the strengthening forces to be applied in terms of the load for which strengthening was designed and the bearing capacity of the member to be strengthened. The maximum value of such forces was also analysed as a function of the capacity of the member to resist counter-gravity moments. An analysis was then conducted of beam-shape interaction when the load on the beam raises since the instant that strengthening is applied, interaction that alters the forces applied to the beam by the shape. This variation can provide an increment in the forces if we cannot introduce them initially with the value calculated as necessary because they were limited by the permanent loads existing when strengthening, or if losses occur in the forces themselves. This is one of the criteria for defining shape specifications. Conversely, such variation may cause the forces to exceed beam counter-gravity bending strength at some points in the span, a development that must also be taken into consideration. Other factors inducing variations in the strengthening force values were then analysed, including deferred concrete strain (creep and shrinkage), temperature gradients in the member and the live loads acting on adjacent spans. The inference drawn was that these developments, which may on occasion have a heavy impact, can be quantified by the design engineer, particularly in ordinary situations, for which simple procedures are proposed. Methodology is likewise proposed for verifying strength in terms of how to appraise beam's cracking and variations in modulus of deformation; safety concerns; the effect of shape lamination tolerance on the calculated deflection necessary for the shape to apply the design forces; and fire-induced situations, among others. Lastly, the most prominent conclusions are discussed and future lines of research are suggested.

Comportamiento, para el terremoto de Lorca de 11-05-2011, de edificios de vigas planas proyectados sin tener en cuenta la acción sísmica

(SPA) El terremoto de Lorca (11-05-2011) fue el movimiento sísmico más destructivo registrado en España, a pesar de su moderada magnitud. Este artículo describe la simulación numérica de la respuesta dinámica, al registro principal del terremoto de Lorca, de seis edificios de tres y seis plantas con forjados unidireccionales de hormigón con vigas planas; estos edificios fueron proyectados sin tener en cuenta la acción sísmica. Se ha elegido esta tipología constructiva por presentar, potencialmente, una elevada vulnerabilidad sísmica. Los seis edificios han sido seleccionados para representar un número importante de edificios de este tipo existentes en zonas de sismicidad baja o media (como Lorca) de España y correspondientes a los años 1974-1994, posteriores a la PDS-1 1974 y previos a la NCSE-94. Los resultados obtenidos muestran que estos edificios, aun contando con la cooperación de los muros, no poseen capacidad para resistir la componente más intensa del registro de Lorca. (ENG)The recent earthquake in Lorca (11-05-2011) was the most destructive recorded event in Spain, despite its moderate magnitude. This paper describes the numerical simulation of the dynamic response to the main record of the Lorca earth-quake of six 3 and 6-story buildings with one-way concrete slabs with wide beams; these buildings were designed without any seismic consideration. We have chosen this type of construction because it is potentially highly vulnerable. The six considered buildings were selected to represent a large number of buildings of this type in areas of low-to-medium seismicity (as Lorca) of Spain along the period 1974-1994. The results show that these buildings, even with the cooperation of the walls, do not have sufficient capacity to withstand the most severe component of the Lorca record.

A methodology to calibrate structural finite element models for reinforced concrete structures subject to blast loads

Civil buildings are not specifically designed to support blast loads, but it is important to take into account these potential scenarios because of their catastrophic effects, on persons and structures. A practical way to consider explosions on reinforced concrete structures is necessary. With this objective we propose a methodology to evaluate blast loads on large concrete buildings, using LS-DYNA code for calculation, with Lagrangian finite elements and explicit time integration. The methodology has three steps. First, individual structural elements of the building like columns and slabs are studied, using continuum 3D elements models subjected to blast loads. In these models reinforced concrete is represented with high precision, using advanced material models such as CSCM_CONCRETE model, and segregated rebars constrained within the continuum mesh. Regrettably this approach cannot be used for large structures because of its excessive computational cost. Second, models based on structural elements are developed, using shells and beam elements. In these models concrete is represented using CONCRETE_EC2 model and segregated rebars with offset formulation, being calibrated with continuum elements models from step one to obtain the same structural response: displacement, velocity, acceleration, damage and erosion. Third, models basedon structural elements are used to develop large models of complete buildings. They are used to study the global response of buildings subjected to blast loads and progressive collapse. This article carries out different techniques needed to calibrate properly the models based on structural elements, using shells and beam elements, in order to provide results of sufficient accuracy that can be used with moderate computational cost.

New courthouse at El Ejido

The courthouse at El Ejido has a trapezoid floor plan (47 m. x 55 / 26 m.) and comprises two distinct volumes that are structurally connected at basement level and by footbridges on the upper storeys. A third trapezoid unit featuring a glazed curtain wall façade cantilevers 8 m. off the main façade of the front volume. This façade is a structural diaphragm wall, constituted by nine rows of vertical precast concrete members separated by horizontal cast-in-place, self-compacting concrete chords. The location of the courthouse in a seismic area and the short number of horizontal supports for the façade make this wall potentially vulnerable. The particularly high risk during construction called for careful planning based on a detailed analysis of the interaction between the structure and the ancillary resources used to build it

Comparison of the seismic behaviour between three building tests, all based on a two storey model house

Integral Masonry System consisting of intersecting steel trusses alo ng each of the three dimensional directions of space on walls and slabs using any masonry material, had yet been backed up by the previous adobe test for seismic areas. This paper presents the comparison this last test and the adaptation of the IMS using h ollow brick. A prototype based on a two storey model house (6mx6mx6m) has being also built in two different scales in order to maximize the load and size of the shake table: the first one half size the whole building (3mx3mx3m) and the second, a quarter of the real size (3mx3mx6m). Both tests have suffered some mild to moderate damages while supporting the higher seismic action subjected by the shake table, without even fissuring the first test and with very few damages the second one. The thickness of the hollow brick wall and the diameter of the tree - dimensional truss reinforcement were scaled to the real size test in order to ascertain its great structural behaviour in relation to the previous structural model calculations. The aim of this study is to sum marize the results of the research collaboration between the ETSAM - UPM and the PUCP in whose laboratory these tests were carried out.

Differences brick facade design to horizontal loads between the Spanish and European standards

Brick facades are a construction type, strongly linked to local construction characteristics and methods. In Spain, particularly in Castilla, the facades have been built since the '80s with Castilian half foot (11.5 cm), resting on the edge of slabs. The design of these facades, to horizontal loads from wind, depending on the codes used, can lead to completely different valid solutions. Applying same loads, the facades studied with current European standard (Eurocode 6), have a maximum length of 7.1 m between supports, while the Spanish code, Technical Building Code - Structural Safety Masonry, (CTE SE-F), 8.4 m can be achieved. This represents an increase of flexural strength, depending on the calculation model used, which can reach until 8 times. This is due to the difference of the calculation method and the structural model in one and another standard, depending on if this facade is analyzed as a vertical or horizontal beam or by formation of a vertical or horizontal archh. This paper analyzes the constructive solution of the brick facades that results from applying Spanish or European standards and how it affects the model applied in the safety of the resulting facade.

Modal analysis of buildings : quantification of uncertainties and model updating

Una estructura vibra con la suma de sus infinitos modos de vibración, definidos por sus parámetros modales (frecuencias naturales, formas modales y coeficientes de amortiguamiento). Estos parámetros se pueden identificar a través del Análisis Modal Operacional (OMA). Así, un equipo de investigación de la Universidad Politécnica de Madrid ha identificado las propiedades modales de un edificio de hormigón armado en Madrid con el método Identificación de los sub-espacios estocásticos (SSI). Para completar el estudio dinámico de este edificio, se ha desarrollado un modelo de elementos finitos (FE) de este edificio de 19 plantas. Este modelo se ha calibrado a partir de su comportamiento dinámico obtenido experimentalmente a través del OMA. Los objetivos de esta tesis son; (i) identificar la estructura con varios métodos de SSI y el uso de diferentes ventanas de tiempo de tal manera que se cuantifican incertidumbres de los parámetros modales debidos al proceso de estimación, (ii) desarrollar FEM de este edificio y calibrar este modelo a partir de su comportamiento dinámico, y (iii) valorar la bondad del modelo. Los parámetros modales utilizados en esta calibración han sido; espesor de las losas, densidades de los materiales, módulos de elasticidad, dimensiones de las columnas y las condiciones de contorno de la cimentación. Se ha visto que el modelo actualizado representa el comportamiento dinámico de la estructura con una buena precisión. Por lo tanto, este modelo puede utilizarse dentro de un sistema de monitorización estructural (SHM) y para la detección de daños. En el futuro, podrá estudiar la influencia de los agentes medioambientales, tales como la temperatura o el viento, en los parámetros modales. A structure vibrates according to the sum of its vibration modes, defined by their modal parameters (natural frequencies, damping ratios and modal shapes). These parameters can be identified through Operational Modal Analysis (OMA). Thus, a research team of the Technical University of Madrid has identified the modal properties of a reinforced-concrete-frame building in Madrid using the Stochastic Subspace Identification (SSI) method and a time domain technique for the OMA. To complete the dynamic study of this building, a finite element model (FE) of this 19-floor building has been developed throughout this thesis. This model has been updated from its dynamic behavior identified by the OMA. The objectives of this thesis are to; (i) identify the structure with several SSI methods and using different time blocks in such a way that uncertainties due to the modal parameter estimation are quantified, (ii) develop a FEM of this building and tune this model from its dynamic behavior, and (iii) Assess the quality of the model, the modal parameters used in this updating process have been; thickness of slabs, material densities, modulus of elasticity, column dimensions and foundation boundary conditions. It has been shown that the final updated model represents the structure with a very good accuracy. Thus, this model might be used within a structural health monitoring framework (SHM). The study of the influence of changing environmental factors (such as temperature or wind) on the model parameters might be considered as a future work.

Modelos de elementos finitos explícitos para explosiones en estructuras reticuladas de hormigón armado : aplicaciones al estudio del colapso de edificios

La frecuencia con la que se producen explosiones sobre edificios, ya sean accidentales o intencionadas, es reducida, pero sus efectos pueden ser catastróficos. Es deseable poder predecir de forma suficientemente precisa las consecuencias de estas acciones dinámicas sobre edificaciones civiles, entre las cuales las estructuras reticuladas de hormigón armado son una tipología habitual. En esta tesis doctoral se exploran distintas opciones prácticas para el modelado y cálculo numérico por ordenador de estructuras de hormigón armado sometidas a explosiones. Se emplean modelos numéricos de elementos finitos con integración explícita en el tiempo, que demuestran su capacidad efectiva para simular los fenómenos físicos y estructurales de dinámica rápida y altamente no lineales que suceden, pudiendo predecir los daños ocasionados tanto por la propia explosión como por el posible colapso progresivo de la estructura. El trabajo se ha llevado a cabo empleando el código comercial de elementos finitos LS-DYNA (Hallquist, 2006), desarrollando en el mismo distintos tipos de modelos de cálculo que se pueden clasificar en dos tipos principales: 1) modelos basados en elementos finitos de continuo, en los que se discretiza directamente el medio continuo mediante grados de libertad nodales de desplazamientos; 2) modelos basados en elementos finitos estructurales, mediante vigas y láminas, que incluyen hipótesis cinemáticas para elementos lineales o superficiales. Estos modelos se desarrollan y discuten a varios niveles distintos: 1) a nivel del comportamiento de los materiales, 2) a nivel de la respuesta de elementos estructurales tales como columnas, vigas o losas, y 3) a nivel de la respuesta de edificios completos o de partes significativas de los mismos. Se desarrollan modelos de elementos finitos de continuo 3D muy detallados que modelizan el hormigón en masa y el acero de armado de forma segregada. El hormigón se representa con un modelo constitutivo del hormigón CSCM (Murray et al., 2007), que tiene un comportamiento inelástico, con diferente respuesta a tracción y compresión, endurecimiento, daño por fisuración y compresión, y rotura. El acero se representa con un modelo constitutivo elastoplástico bilineal con rotura. Se modeliza la geometría precisa del hormigón mediante elementos finitos de continuo 3D y cada una de las barras de armado mediante elementos finitos tipo viga, con su posición exacta dentro de la masa de hormigón. La malla del modelo se construye mediante la superposición de los elementos de continuo de hormigón y los elementos tipo viga de las armaduras segregadas, que son obligadas a seguir la deformación del sólido en cada punto mediante un algoritmo de penalización, simulando así el comportamiento del hormigón armado. En este trabajo se denominarán a estos modelos simplificadamente como modelos de EF de continuo. Con estos modelos de EF de continuo se analiza la respuesta estructural de elementos constructivos (columnas, losas y pórticos) frente a acciones explosivas. Asimismo se han comparado con resultados experimentales, de ensayos sobre vigas y losas con distintas cargas de explosivo, verificándose una coincidencia aceptable y permitiendo una calibración de los parámetros de cálculo. Sin embargo estos modelos tan detallados no son recomendables para analizar edificios completos, ya que el elevado número de elementos finitos que serían necesarios eleva su coste computacional hasta hacerlos inviables para los recursos de cálculo actuales. Adicionalmente, se desarrollan modelos de elementos finitos estructurales (vigas y láminas) que, con un coste computacional reducido, son capaces de reproducir el comportamiento global de la estructura con una precisión similar. Se modelizan igualmente el hormigón en masa y el acero de armado de forma segregada. El hormigón se representa con el modelo constitutivo del hormigón EC2 (Hallquist et al., 2013), que también presenta un comportamiento inelástico, con diferente respuesta a tracción y compresión, endurecimiento, daño por fisuración y compresión, y rotura, y se usa en elementos finitos tipo lámina. El acero se representa de nuevo con un modelo constitutivo elastoplástico bilineal con rotura, usando elementos finitos tipo viga. Se modeliza una geometría equivalente del hormigón y del armado, y se tiene en cuenta la posición relativa del acero dentro de la masa de hormigón. Las mallas de ambos se unen mediante nodos comunes, produciendo una respuesta conjunta. En este trabajo se denominarán a estos modelos simplificadamente como modelos de EF estructurales. Con estos modelos de EF estructurales se simulan los mismos elementos constructivos que con los modelos de EF de continuo, y comparando sus respuestas estructurales frente a explosión se realiza la calibración de los primeros, de forma que se obtiene un comportamiento estructural similar con un coste computacional reducido. Se comprueba que estos mismos modelos, tanto los modelos de EF de continuo como los modelos de EF estructurales, son precisos también para el análisis del fenómeno de colapso progresivo en una estructura, y que se pueden utilizar para el estudio simultáneo de los daños de una explosión y el posterior colapso. Para ello se incluyen formulaciones que permiten considerar las fuerzas debidas al peso propio, sobrecargas y los contactos de unas partes de la estructura sobre otras. Se validan ambos modelos con un ensayo a escala real en el que un módulo con seis columnas y dos plantas colapsa al eliminar una de sus columnas. El coste computacional del modelo de EF de continuo para la simulación de este ensayo es mucho mayor que el del modelo de EF estructurales, lo cual hace inviable su aplicación en edificios completos, mientras que el modelo de EF estructurales presenta una respuesta global suficientemente precisa con un coste asumible. Por último se utilizan los modelos de EF estructurales para analizar explosiones sobre edificios de varias plantas, y se simulan dos escenarios con cargas explosivas para un edificio completo, con un coste computacional moderado. The frequency of explosions on buildings whether they are intended or accidental is small, but they can have catastrophic effects. Being able to predict in a accurate enough manner the consequences of these dynamic actions on civil buildings, among which frame-type reinforced concrete buildings are a frequent typology is desirable. In this doctoral thesis different practical options for the modeling and computer assisted numerical calculation of reinforced concrete structures submitted to explosions are explored. Numerical finite elements models with explicit time-based integration are employed, demonstrating their effective capacity in the simulation of the occurring fast dynamic and highly nonlinear physical and structural phenomena, allowing to predict the damage caused by the explosion itself as well as by the possible progressive collapse of the structure. The work has been carried out with the commercial finite elements code LS-DYNA (Hallquist, 2006), developing several types of calculation model classified in two main types: 1) Models based in continuum finite elements in which the continuous medium is discretized directly by means of nodal displacement degrees of freedom; 2) Models based on structural finite elements, with beams and shells, including kinematic hypothesis for linear and superficial elements. These models are developed and discussed at different levels: 1) material behaviour, 2) response of structural elements such as columns, beams and slabs, and 3) response of complete buildings or significative parts of them. Very detailed 3D continuum finite element models are developed, modeling mass concrete and reinforcement steel in a segregated manner. Concrete is represented with a constitutive concrete model CSCM (Murray et al., 2007), that has an inelastic behaviour, with different tension and compression response, hardening, cracking and compression damage and failure. The steel is represented with an elastic-plastic bilinear model with failure. The actual geometry of the concrete is modeled with 3D continuum finite elements and every and each of the reinforcing bars with beam-type finite elements, with their exact position in the concrete mass. The mesh of the model is generated by the superposition of the concrete continuum elements and the beam-type elements of the segregated reinforcement, which are made to follow the deformation of the solid in each point by means of a penalty algorithm, reproducing the behaviour of reinforced concrete. In this work these models will be called continuum FE models as a simplification. With these continuum FE models the response of construction elements (columns, slabs and frames) under explosive actions are analysed. They have also been compared with experimental results of tests on beams and slabs with various explosive charges, verifying an acceptable coincidence and allowing a calibration of the calculation parameters. These detailed models are however not advised for the analysis of complete buildings, as the high number of finite elements necessary raises its computational cost, making them unreliable for the current calculation resources. In addition to that, structural finite elements (beams and shells) models are developed, which, while having a reduced computational cost, are able to reproduce the global behaviour of the structure with a similar accuracy. Mass concrete and reinforcing steel are also modeled segregated. Concrete is represented with the concrete constitutive model EC2 (Hallquist et al., 2013), which also presents an inelastic behaviour, with a different tension and compression response, hardening, compression and cracking damage and failure, and is used in shell-type finite elements. Steel is represented once again with an elastic-plastic bilineal with failure constitutive model, using beam-type finite elements. An equivalent geometry of the concrete and the steel is modeled, considering the relative position of the steel inside the concrete mass. The meshes of both sets of elements are bound with common nodes, therefore producing a joint response. These models will be called structural FE models as a simplification. With these structural FE models the same construction elements as with the continuum FE models are simulated, and by comparing their response under explosive actions a calibration of the former is carried out, resulting in a similar response with a reduced computational cost. It is verified that both the continuum FE models and the structural FE models are also accurate for the analysis of the phenomenon of progressive collapse of a structure, and that they can be employed for the simultaneous study of an explosion damage and the resulting collapse. Both models are validated with an experimental full-scale test in which a six column, two floors module collapses after the removal of one of its columns. The computational cost of the continuum FE model for the simulation of this test is a lot higher than that of the structural FE model, making it non-viable for its application to full buildings, while the structural FE model presents a global response accurate enough with an admissible cost. Finally, structural FE models are used to analyze explosions on several story buildings, and two scenarios are simulated with explosive charges for a full building, with a moderate computational cost.

Criterios técnicos del proyecto con módulos tridimensionales ligeros: las casas del Solar Decathlon 2005 y 2007

Este trabajo se ocupa de la construcción modular ligera de viviendas unifamiliares, más concretamente aborda el problema de la definición constructiva de las mismas, habida cuenta de lo poco conocido y publicado de este aspecto en particular. Dado que la construcción es fruto de la evolución, resulta de gran importancia el estudio de los antecedentes para comprender la situación actual, por ello para documentar como corresponde el estado de la técnica y de la investigación se estudiaron los antecedentes desde sus primeras manifestaciones a finales del siglo XIX hasta nuestros días. Contrariamente a las profecías de Le Corbusier y otros, la industrialización no ha llegado a la construcción ni en la forma ni en la medida que era de esperar a principios del siglo XX. Sin embargo y a pesar del relativo “fracaso” de la industrialización en convertirse en la forma mayoritaria de producir edificios, lo cierto es que algunos sistemas altamente industrializados, como lo es la construcción modular ligera, han logrado un lugar en el mercado, que en algunos países resulta cuanto menos significativo. Delimitar el estado de la técnica y la situación actual es crucial en este trabajo, toda vez que la construcción industrializada la realizan empresas, y situarse al margen de las mismas y de su producción, nos guste o no, resulta contrario al sentido común. De este modo se han identificado y documentado ejemplos como el de EE.UU. y Japón, entre otros, que resultan muy ilustrativos tanto desde la evolución como del estado actual. Del estado de la técnica y la investigación también resulta la escasez de publicación de detalles constructivos específicos de la construcción modular ligera. Es obvio que los fabricantes intentan blindarse mediante el secreto industrial, logrando que las soluciones constructivas más interesantes queden fuertemente protegidas dentro del conocimiento reservado de la empresa. De este modo un sistema que alcanza grados de prefabricación del 95%, tan atractivo e interesante para el arquitecto queda reservado al conocimiento de unos pocos dentro de las empresas. La búsqueda de mayor información sobre estos sistemas encuentra un filón indiscutible en los proyectos de las casas del concurso Solar Decathlon. En efecto, debido a las condiciones particulares de este concurso, las casas que compiten deben ser instaladas en un plazo corto, por lo que en su mayoría recurren al método de construcción modular ligera, para lograr correctamente este objetivo. Adicionalmente todos los planos de proyecto incluidos los de detalle, así como memorias de especificaciones técnicas, quedan colgadas en la Web, a libre disposición del público. De este modo se ha considerado interesante, conveniente y útil, aprovechar como fuente documental de este trabajo, aparte de lo obtenido en el estado de la técnica y la investigación, los proyectos de las casas de los concursos 2005 y 2007, que fueron las dos últimas ediciones celebradas cuando se inició esta tesis. De modo similar a esta carencia de detalles publicados se observa igualmente una falta de investigación y de metodologías adecuadas a la misma sobre soluciones y detalles constructivos propios de la construcción modular ligera. Por eso y ante la dificultad de manejar adecuadamente una información disponible pero farragosa, este trabajo ha dedicado una parte importante de su esfuerzo a la creación de una metodología adecuada a este tipo de situación. Hay que destacar que cada proyecto puede constar fácilmente de 60 a casi 200 planos, sin contar las memorias técnicas y otros documentos, tales como galerías de imágenes, etc. Por otra parte resulta útil establecer esta metodología, no solo para esta tesis, sino para futuros trabajos de investigación sobre el tema, toda vez que con posterioridad a 2007 se han celebrado nuevas ediciones del concurso con su correspondiente volumen de información disponible. La metodología del análisis de los proyectos se basa en el diseño y creación de siete fichas tipo que resumen los aspectos fundamentales del proyecto desde el punto de vista constructivo, permitiendo de este modo su rápida visualización y comprensión sin pretender exhaustividad, ya que en caso de querer profundizar en el detalle de la información siempre está el proyecto original para ello. Tras estudiar la información obtenida de los proyectos de las casas de concurso, se contrastan y discuten los resultados para obtener conocimientos de interés para el objetivo propuesto en la tesis. Se comparan los resultados procedentes del estado de la técnica y de la investigación y se obtienen las conclusiones correspondientes. De este modo ha sido posible identificar una serie de criterios técnicos de proyecto de viviendas unifamiliares realizadas mediante construcción modular ligera, que además se organizan en varios niveles, por lo que el resultado es un conjunto de criterios como germen de una futura guía o manual. Como conclusiones fundamentales de la tesis hay que destacar las metodológicas, que habilitan la extensión de este estudio a otros trabajos y la aportación original al conocimiento con la definición de una serie de criterios técnicos de proyecto de viviendas realizadas mediante construcción modular ligera, que además de mejorar esta parte del saber constructivo serán de gran ayuda a los arquitectos de cara a la reducción de errores, que a menudo derivan en mayores costes y plazos, cuando no directamente al abandono del sistema constructivo. El trabajo de la tesis se estructura en siete capítulos a saber: Capítulo 1: Introducción, donde se explica el tema de la tesis, el objetivo principal, las limitaciones y se aportan algunas definiciones. Capítulo 2: Estado de la técnica y la investigación, dentro del cual se presentan los antecedentes desde sus inicios pasando por la primera y segunda mitad del siglo XX y finalizando con el estado actual que recorre los sistemas de EE.UU, Japón, Europa, Escandinavia, centro Europa, Francia, España y algunos ejemplos de Latinoamérica. En el estado de la investigación se presentan las publicaciones tanto en revistas científicas indexadas en el JCR, como publicaciones no indexadas en las que se muestran artículos científicos, comunicaciones a congresos, documentación sobre el concurso Solar Decathlon, libros específicos y libros genéricos sobre construcción modular ligera, tesis doctorales tanto generales como específicas sobre el concurso Solar Decathlon, documentos de idoneidad técnica, páginas Web del concurso Solar Decathlon y finalmente páginas Web de empresas de construcción modular ligera y patentes. También se expresan las conclusiones parciales del capítulo así también como la justificación y los objetivos particulares. Capítulo 3: Metodología, se expone en primer lugar el planteamiento del problema, para luego desarrollar los métodos utilizados para el estudio y clasificación del transporte y de la organización modular, la relación entre la organización modular y distribución espacial, el diseño y contenido de las fichas resumen de los 38 proyectos presentados al SD2005 y SD2007, así también como la información consultada para su realización. Se explica asimismo como se realizaron las tablas comparativas partiendo de la información de las fichas. Finalmente se expresa la manera en que se trató el estudio particular de la junta entre módulos. Capítulo 4: Discusión de resultados, dónde en primer lugar se presenta la clasificación y las estrategias del transporte así también como una clasificación de la organización modular, en segundo lugar se estudian las relaciones que existen entre el sistema modular y la organización espacial. A partir de aquí se muestra el estudio de la estructura de todas las casas del SD2005 y SD2007, según el tipo y material de las zapatas, mostrando tanto tablas cuantitativas como tablas gráficas con fotos. De la misma manera se tratan los forjados, los pilares y las vigas y las cubiertas. Se estudia además el cerramiento opaco y acristalado, la cubierta y el forjado según las capas que lo componen. En el caso de las instalaciones se estudian las que son especiales, descartando las normales en este tipo de casas, como son los paneles fotovoltaicos, placas térmicas o tubos de vacío y los sistemas de almacenamiento de energía, como las baterías, presentando tablas numéricas y gráficas con fotos. El transporte se analiza según corresponda al traslado de la vivienda o al transporte de apoyo, según el tipo y la cantidad utilizado. Con respecto al montaje se diferencia en si se usó grúa o no, y en el caso de no utilizarse se muestran los métodos alternativos. Con respecto a la exploración de la organización modular se presentan la cantidad de módulos que utilizó cada casa, así como también la cuantificación de los sistemas híbridos como son elementos lineales 1D, paneles 2D. Por último se muestra el estudio detallado de la junta entre módulos 3D. Finalmente se realiza la propuesta de un conjunto de criterios técnicos de proyecto organizado en cuatro niveles: 1º nivel de criterios generales, 2º nivel sobre sistemas constructivos, 3º nivel de detalles constructivos y el 4º nivel llamado logística obras previas, transporte y montaje. Capítulo 5: Conclusiones y líneas futuras de investigación, se exponen las conclusiones generales, metodológicas, documentales y por último las de construcción modular. Finalmente se realiza una propuesta de líneas futuras de investigación. Capítulo 6: Bibliografía. Capítulo 7: Anexos, en el que se presentan todas las fichas resumen de las casas realizadas por el autor de esta tesis. Además se incluyen los casos concretos de Voisin en Francia y la TVA (Tennessee Valley Authority) en EE.UU., así como referencias de manuales genéricos de construcción ligera, medidas de transporte en España e información sobre estadísticas de viviendas en la Unión Europea. ABSTRACT This paper deals with Light Modular Construction of houses, and specifically addresses the problem of the constructive definition of the same, given how little known and published this subject has been. Since building construction is the result of evolution, it is of great importance to study its background for understanding the current situation, therefore to document the state of the art and research, its history was studied from its origins dating to the end nineteenth century to our days. Contrary to the prophecies of Le Corbusier and others, industrialization has not reached the construction neither in the form nor to the extent that it was expected in the early twentieth century. However, despite the relative "failure" of industrialization to become the major form of production for buildings, the fact is that some highly industrialized systems, such as the so called Lightweight Modular Construction, have achieved a place in the market, which in some countries is at least significant. To outline the state of the art and the current situation is crucial in this work, since industrialized construction is carried out by companies, and to step away from them and their production, whether we like it or not, it is contrary to common sense. So that, several cases have been identified and documented, such as the US and Japan examples, among others, which are very illustrative both from evolution and the current status. The state of the art and research shows also a shortage of publication of specific construction details of light modular construction. Obviously, manufacturers try to shield themselves by trade secret, making the most interesting constructive solutions remain heavily protected within the reserved knowledge of the company, so a system that reaches levels of 95% prefabrication, so attractive and interesting for the architect It is reserved to the knowledge of a few people inside the companies. The search for more information on these systems finds an invaluable reef in the projects of the Solar Decathlon houses. Indeed, due to the particular conditions of this contest, houses competing must be installed in a short time, so mostly turn to modular construction methods for this purpose to achieve properly this goal. Additionally all levels of project, including detailed and technical specifications reports are published on the Web, freely available to the general public. Thus it was considered interesting, convenient and useful to take advantage as a documentary source of this work, apart from what it were obtained in the state of the art and research, the projects of the houses of the 2005 and 2007 contests, which were the last two editions already held before this thesis was started. Similar to this lack of published details it is also observed a lack of research and methodologies adapted to the solutions and construction details of lightweight modular construction. So that, and facing the difficulty of adequately manage the available but bulky information, this work has devoted a significant part of its effort to create an appropriate methodology for this type of situation. It is noteworthy that each project can easily consist of 60 to almost 200 blueprints, not including technical reports and other documents, such as photo galleries, etc. The methodology of the analysis of the projects is based on the design and creation of seven record sheets that summarize key aspects of the project from a construction point of view, thus allowing quick watching and understanding of the project, without claiming completeness, always keeping for further information the blueprints themselves. After studying the information obtained from the projects of the competition houses, the results are compared and discussed to obtain relevant knowledge according to the objective proposed in the thesis. The results from the state of the art and research are also compared and the conclusions so obtained make possible to identify a number of technical design criteria for single family homes made using lightweight modular construction, which also have been organized at various levels, so the result is a set of criteria as a seed for a future guide or manual. Among the main conclusions of the thesis must be noted the methodological ones, that enable the extension of this study to other works and are an original contribution to knowledge with the definition of a number of technical criteria for housing projects made by light modular construction, what in addition to improving this part of the constructive knowledge will be of great help for the architects to reduce errors that often result in higher costs and delays, if not in abandonment of the construction system itself. The work of the thesis is divided into seven chapters as follows: Chapter 1: Introduction, where the topic of the thesis, the main objective, limitations and the provided definitions is explained. Chapter 2: State of the art and research, within which history is presented from the beginning through the first and second half of the twentieth century and ending with the current systems, that spans from the USA to Japan, Europe, Scandinavia, Central Europe, France, Spain and some Latin American examples. In the state of research publications are presented both on scientific journals indexed in the JCR, and non-indexed publications in which scientific articles, conference papers, information about the Solar Decathlon competition, generic and specific books on light modular construction, articles both general and specific on the Solar Decathlon competition, technical approval documents, dissertations, the Solar Decathlon Web pages and finally lightweight modular construction companies Web pages and patents. The partial conclusions of the chapter as well as the rationale and specific objectives are also expressed. Chapter 3: Methodology first of all exposes the problem statement and then develops the methods used for the study and classification of transportation and modular organization, the relationship between the modular organization and spatial distribution, design and content summary records of the 38 projects submitted to the SD2005 and SD2007, as well as information consulted for its realization. It explains equally how the comparative tables based on information from the chips were made. Finally, the way the particular study of the joint between modules is carried out is also treated. Chapter 4: Discussion, first sorting a classification of transport strategies as well as of modular organization, secondly the relationship between the modular system and the spatial organization studied is presented. From then on, the study of the structure of every house Moreover, to establish this methodology is useful not only for this thesis, but for future research on the subject, since after 2007 there have been held new editions of the contest with a corresponding volume of information available. shown in the SD2005 and SD2007 contests, depending on the type and material of the shoe, showing both quantitative tables as graphic boards with pictures is carried out. Similarly slabs, columns and beams and roofs are treated. Furthermore, the opaque and transparent façades, as well as roof and floor enclosure, according to the layers that compose them are studied. In the case of facilities there have been only addressed that which are of a special type, discarding that considered usual in this type of houses such as photovoltaic panels, thermal panels or vacuum tubes and energy storage systems such as batteries, presenting numerical and graphical tables with photos .The transportation is analyzed depending on it is used to move the house or for additional support, depending on the type and quantity of items used. Regarding assembly it has been made a difference if crane is or not used and if not, what the alternative methods are. With respect to the exploration of the modular organization, the amount of modules used in each house is presented, as well as the quantification of hybrid systems such as linear members as well as 1D, 2D panels. Finally, it has been carried out the detailed study of the joint between 3D modules. Finally it is proposed a set of technical criteria organized into four levels, 1st level of general criteria, 2nd level on building systems, 3rd level construction details and 4th level called previous works and logistics, transportation and assembly. Chapter 5: Conclusions and future research, where general, methodological, documentary and finally modular construction findings are presented. A proposal for further research is done. Chapter 6: Bibliography. Chapter 7: Annexes, in which all the record sheets of houses made by the author of this thesis are presented. Besides the specific cases of Voisin in France and TVA (Tennessee Valley Authority) in the USA, as well as general reference manuals on lightweight construction, transportation dimensions in Spain, and information on housing statistics in the European Union are included.

Leading role of thalamic over cortical neurons during postinhibitory rebound excitation

The postinhibitory rebound excitation is an intrinsic property of thalamic and cortical neurons that is implicated in a variety of normal and abnormal operations of neuronal networks, such as slow or fast brain rhythms during different states of vigilance as well as seizures. We used dual simultaneous intracellular recordings of thalamocortical neurons from the ventrolateral nucleus and neurons from the motor cortex, together with thalamic and cortical field potentials, to investigate the temporal relations between thalamic and cortical events during the rebound excitation that follows prolonged periods of stimulus-induced inhibition. Invariably, the rebound spike-bursts in thalamocortical cells occurred before the rebound depolarization in cortical neurons and preceded the peak of the depth-negative, rebound field potential in cortical areas. Also, the inhibitory-rebound sequences were more pronounced and prolonged in cortical neurons when elicited by thalamic stimuli, compared with cortical stimuli. The role of thalamocortical loops in the rebound excitation of cortical neurons was shown further by the absence of rebound activity in isolated cortical slabs. However, whereas thalamocortical neurons remained hyperpolarized after rebound excitation, because of the prolonged spike-bursts in inhibitory thalamic reticular neurons, the rebound depolarization in cortical neurons was prolonged, suggesting the role of intracortical excitatory circuits in this sustained activity. The role of intrathalamic events in triggering rebound cortical activity should be taken into consideration when analyzing information processes at the cortical level; at each step, corticothalamic volleys can set into action thalamic inhibitory neurons, leading to rebound spike-bursts that are transferred back to the cortex, thus modifying cortical activities.

Comportamento de chumbadores embutidos em concreto com fibras de aço para ligações viga-pilar de concreto pré-moldado

O presente trabalho trata do estudo do comportamento de chumbadores grauteados inseridos em concreto com fibras de aço em ligações viga-pilar de estruturas de concreto pré-moldado. Este estudo é importante para se entender e poder quantificar a influência da rigidez deste componente no comportamento de ligações semirrígidas de estruturas de concreto pré-moldado. O objetivo do trabalho é estudar o mecanismo do chumbador no concreto com fibras de aço em ensaios específicos e avaliar também o comportamento de uma ligação viga-pilar de concreto pré-moldado utilizando estas fibras no consolo e no dente da viga. Nesta pesquisa foi realizado um programa experimental no Laboratório de Estruturas da EESC, uma análise numérica com o emprego do software DIANA® e uma comparação com formulações analíticas existentes para o cálculo da força última destes componentes. Foram ensaiados nove modelos experimentais para avaliar especificamente o mecanismo resistente do chumbador, variando-se os diâmetros das barras, sua inclinação e a porcentagem de fibras de aço no concreto. Além destes modelos, foi realizado ensaio de uma ligação viga-pilar de concreto pré-moldado para avaliar a rigidez da ligação com chumbador inserido em concreto com fibras de aço. Nos ensaios experimentais dos chumbadores observou-se que modelos com concreto com fibras de aço apresentam rigidez até 25% maior se comparado ao modelo com concreto convencional. Verificou-se que o graute utilizado para solidarizar os chumbadores exerce significativa influência na capacidade última do modelo, podendo diminuir em cerca de 30% a capacidade de carga. A ligação viga-pilar de concreto pré-moldado utilizando concreto com fibras de aço no consolo e no dente da viga se comportou de maneira satisfatória, não apresentando fissuração na interface dos diferentes concretos. Na comparação dos modelos ensaiados com as formulações teóricas extraídas de trabalhos de referência verificou-se que, para os modelos específicos de chumbador, a formulação existente é representativa. Para a ligação viga-pilar, alguns ajustes na formulação analítica se fizeram necessários para considerações de efeitos de grupo e de borda observados e decorrentes da utilização de dois chumbadores na ligação proposta neste trabalho.

Novo procedimento para a realização de análise capwap no ensaio de carregamento dinâmico em estacas pré-moldadas.

Desde a década de 1980 diversos autores apresentaram correlações entre provas de carga estática e ensaios de carregamento dinâmico em estacas. Para uma boa correlação é fundamental que os testes sejam bem executados e que atinjam a ruptura segundo algum critério, como o de Davisson, por exemplo, além de levar em conta o intervalo de tempo entre a execução da prova de carga estática e do ensaio dinâmico, face ao efeito \"set up\". Após a realização do ensaio dinâmico realiza-se a análise CAPWAP que permite a determinação da distribuição do atrito lateral em profundidade, a carga de ponta e outros parâmetros dos solos tais como quakes e damping. A análise CAPWAP é realizada por tentativas através do procedimento \"signal matching\", isto é, o melhor ajuste entre os sinais de força medido pelos sensores e o calculado. É relativamente fácil mostrar que a mesma solução pode ser obtida através de dados de entrada diferentes. Isso significa que apesar de apresentarem cargas mobilizadas próximas o formato da curva da simulação de prova de carga estática, obtida pelo CAPWAP, assim como a distribuição do atrito lateral, podem ser diferentes, mesmo que as análises apresentem \"match quality\" (MQWU) satisfatórios. Uma forma de corrigir o formato da curva simulada do CAPWAP, assim como a distribuição do atrito lateral, é através da comparação com provas de carga estática (PCE). A sobreposição das duas curvas, a simulada e a \"real\", permite a determinação do quake do fuste através do trecho inicial da curva carga-recalque da prova de carga estática, que por sua vez permite uma melhor definição da distribuição do atrito lateral e da reação de ponta. Neste contexto surge o conceito de \"match quality de recalques\" (MQR). Quando a PCE não está disponível, propõe-se efetuar um carregamento estático utilizando o peso próprio do martelo do bate-estaca (CEPM). Mostra-se, através de dois casos de obra, em que estavam disponíveis ensaios de carregamento dinâmico e PCEs, que esse procedimento permite obter uma melhor solução do ponto de vista físico, isto é consistente com as características do subsolo e com a curva carga-recalque da PCE, e não apenas matemático, através da avaliação do \"match quality\" (MQWU).

Mathematical modeling of drying process of unripe banana slices

Unripe banana flour (UBF) production employs bananas not submitted to maturation process, is an interesting alternative to minimize the fruit loss reduction related to inappropriate handling or fast ripening. The UBF is considered as a functional ingredient improving glycemic and plasma insulin levels in blood, have also shown efficacy on the control of satiety, insulin resistance. The aim of this work was to study the drying process of unripe banana slabs (Musa cavendishii, Nanicão) developing a transient drying model through mathematical modeling with simultaneous moisture and heat transfer. The raw material characterization was performed and afterwards the drying process was conducted at 40 ºC, 50 ºC e 60 ºC, the product temperature was recorded using thermocouples, the air velocity inside the chamber was 4 m·s-1. With the experimental data was possible to validate the diffusion model based on the Fick\'s second law and Fourier. For this purpose, the sorption isotherms were measured and fitted to the GAB model estimating the equilibrium moisture content (Xe), 1.76 [g H2O/100g d.b.] at 60 ºC and 10 % of relative humidity (RH), the thermophysical properties (k, Cp, ?) were also measured to be used in the model. Five cases were contemplated: i) Constant thermophysical properties; ii) Variable properties; iii) Mass (hm), heat transfer (h) coefficient and effective diffusivity (De) estimation 134 W·m-2·K-1, 4.91x10-5 m-2·s-1 and 3.278?10-10 m·s-2 at 60 ºC, respectively; iv) Variable De, it presented a third order polynomial behavior as function of moisture content; v) The shrinkage had an effect on the mathematical model, especially in the 3 first hours of process, the thickness experienced a contraction of about (30.34 ± 1.29) % out of the initial thickness, finding two decreasing drying rate periods (DDR I and DDR II), 3.28x10-10 m·s-2 and 1.77x10-10 m·s-2, respectively. COMSOL Multiphysics simulations were possible to perform through the heat and mass transfer coefficient estimated by the mathematical modeling.

Influência da substituição de matérias primas nas propriedades dos fluxantes para lingotamento contínuo de aços médio carbono

O fluxante é uma escória sintética que influencia na qualidade superficial do aço e na estabilidade do processo de lingotamento contínuo. Este produto é aplicado diretamente sobre o aço líquido na região do molde de cobre refrigerado a água e atua diretamente no resfriamento primário do aço. O fluxante tem as propriedades físico-químicas adaptadas para cada tipo de aço e também para as condições de lingotamento. Na superfície do aço líquido, o fluxante funde e forma uma poça líquida, atuando como isolante térmico, protegendo o aço da reoxidação e absorvendo inclusões principalmente de Al2O3. A poça líquida escoa, lubrificando e controlando a transferência de calor na interface entre o molde e a pele de aço em solidificação. O problema de qualidade superficial do aço, quando relacionado ao fluxante, se resume a alarmes de colamento, trincas de quina, marcas de oscilação profundas e trincas longitudinais, sendo este último um problema particular do aço médio carbono. Neste trabalho, foram analisados diferentes fluxantes baseados inicialmente no fluxante comercial aplicado no lingotamento contínuo de placas de aço médio carbono. Todos os fluxantes foram desenvolvidos com composições químicas similares. O objetivo foi avaliar o impacto da substituição de fontes de matérias-primas em diferentes composições de modo a avaliar as propriedades físico-químicas com base no fluxante comercial de referência. Como resultado, de todas as propriedades físico-químicas, foi a temperatura de cristalização que sofreu a alteração mais significativa.