Avaliação da potencialidade de argilas do Rio Grande do Norte – Brasil

DUTRA, Ricardo Peixoto Suassuna ; SILVA, Jaquelígia Brito da ; MORAES, Márcio Luiz Varela Nogueira de ; NASCIMENTO, R. M. ; GOMES, Uilame Umbelino ; PASKOCIMAS, Carlos Alberto . Avaliação da potencialidade de argilas do Rio Grande do Norte. Cerâmica Industrial, v. 13, p. 47-50, 2008.

Estudo do comportamento plástico, mecânico, microestrutural e térmico do concreto produzido com resíduo de porcelanato

Population growth experienced in major cities, allied to society s need of infra-structure, especially ones related to habitational demands, increases the consumption of construction materials. As a consequence, consumption of natural resources itself. Thus, due to this process, concrete is one of the most produced materials in civil construction. This is also due to the great diversity of its application, easiness in its execution and adequate mechanical performance, as well as low production costs. Following the same tendencies in construction development, the ceramic industry has intensified the production of porcelain ceramic tiles and floors. These are achieved by a fine finishing and receive polishing at the end of the fabrication process. This work researched the use of porcelain residues in polishing for the production of concrete. All of which; due to economical and environmental issues. This process aims to prove adequate destiny for this type of residue, due to environmental issues, incorporating it to the concrete itself; all of which provides economy in consumption of the materials that constitute concrete. Thus, the main characteristics of concrete were investigated through the inclusion of different concentration of the porcelain residue as additional trait element. The residue rates incorporated to the trait varied from 10% to 50% in relation to the cement mass, in the traits with plastic additives and without plastic additives. It is observed that the inclusion of porcelain residue produced a meaningful alteration in the consistency of fresh concrete. This residue has a fine granulometry and it considerably absorbed the water used in the concrete spreading, influencing the way this material is dealt with. Thus, the value of cement striking decreases with the increase of residues present in trait. The maximal incorporation of the residue was of 50%, massively, for the same factor water/initial cement. The use of residues in concrete results in an 40% increase in the compression resistance. It is also proportional to residue concentration of porcelain in the trait. The microstructure was also favored once porosity and concrete absorption decreases with the use of this residue. The parameters demonstrate the quality and durability of the concrete produced with this residue. The use of porcelain residue in concrete composition has not produced meaningful thermal behavior changes. Thermal conductivity, heat capacity and thermal diffusivity have been maintained basically constant

Análise mecânica e microestrutural das ligas de cobalto-cromo de uso odontológico após sucessivas refundições

The cobalt-chromium alloy is extensively used in the Odontology for the confection of metallic scaffolding in partial removable denture. During the last few years, it has been reported an increasing number of premature imperfections, with a few months of prosthesis use. The manufacture of these components is made in prosthetic laboratories and normally involves recasting, using parts of casting alloy and parts of virgin alloy. Therefore, the objective of the present study was to analyze the mechanical properties of a commercial cobalt-chromium alloy of odontological use after successive recasting, searching information to guide the dental prosthesis laboratories in the correct manipulation of the cobalt-chromium alloy in the process of casting and the possible limits of recasting in the mechanical properties of this material. Seven sample groups were confectioned, each one containing five test bodies, divided in the following way: G1: casting only with virgin alloy; G2: casting with 50% of the alloy of the G1 + 50% of virgin alloy; G3: casting with 50% of the alloy of the G2 + 50% of virgin alloy; G4: casting with 50% of the alloy of the G3 + 50% of virgin alloy; G5: 50% of alloy of the G4 + 50% of virgin alloy; G6: 50% of alloy of the G5 + 50% of virgin alloy and finally the G7, only with recasting alloy. The modifications in the mechanical behavior of the alloy were evaluated. Moreover, it was carried the micro structural characterization of the material by optic and electronic scanning microscopy, and X ray diffraction.and fluorescence looking into the correlatation of the mechanical alterations with structural modifications of the material caused by successive recasting process. Generally the results showed alterations in the fracture energy of the alloy after successive recasting, resulting mainly of the increasing presence of pores and large voids, characteristic of the casting material. Thus, the interpretation of the results showed that the material did not reveal significant differences with respect to the tensile strength or elastic limit, as a function of successive recasting. The elastic modulus increased from the third recasting cycle on, indicating that the material can be recast only twice. The fracture energy of the material decreased, as the number of recasting cycles increased. With respect to the microhardness, the statistical analyses showedno significant differences. Electronic scanning microscopy revealed the presence of imperfections and defects, resulting of the recasting process. X ray diffraction and fluorescence did not show alterations in the composition of the alloy or the formation of crystalline phases between the analyzed groups. The optical micrographs showed an increasing number of voids and porosity as the material was recast. Therefore, the general conclusion of this study is that the successive recasting of of Co-Cr alloys affects the mechanical properties of the material, consequently leading to the failure of the prosthetic work. Based on the results, the best recommendadition is that the use of the material should be limited to two recasting cycles

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Aplicação da metodologia de planejamento de experimentos para formulação de massas cerâmicas para telhas

Rio Grande do Norte State stands out as one great producer of structural clay of the brazilian northeastern. The Valley Assu ceramic tiles production stands out obtained from ilitics ball clays that abound in the region under study. Ceramics formulation and the design of experiments with mixture approach, has been applied for researchers, come as an important aid to decrease the number of experiments necessary to the optimization. In this context, the objective of this work is to evaluate the effects of the formulation, temperature and heating rate in the physical-mechanical properties of the red ceramic body used for roofing tile fabrication of the Valley Assu, using design of mixture experiments. Four clays samples used in two ceramics industry of the region were use as raw material and characterized by X-ray diffraction, chemical composition, differential thermal analysis (DTA), thermogravimetric analysis (TGA), particle size distribution analysis and plasticity techniques. Afterwards, they were defined initial molded bodies and made specimens were then prepared by uniaxial pressing at 25 MPa before firing at 850, 950 and 1050 ºC in a laboratory furnace, with heating rate in the proportions of 5, 10 e 15 ºC/min. The following tecnologicals properties were evaluated: linear firing shrinkage, water absorption and flexural strength. Results show that the temperature 1050 ºC and heating rate of 5 ºC/min was the best condition, therefore presented significance in all physical-mechanical properties. The model was accepted as valid based of the production of three new formulations with fractions mass diferents of the initial molded bodies and heated with temperature at 1050 ºC and heating rate of 5 ºC/min. Considering the formulation, temperature and heating rate as variables of the equations, another model was suggested, where from the aplication of design of experiments with mixtures was possible to get a best formulation, whose experimental error is the minor in relation to the too much formulations

Pastas compósitas cimento/sílica/polímero para cimentação de poços de baixa profundidade sujeitas à injeção de vapor

The production of heavy oil fields, typical in the Northeastern region, is commonly stimulated by steam injection. High bottom hole temperatures are responsible not only for the development of deleterious stresses of the cement sheath but also for cement strength retrogression. To overcome this unfavorable scenario, polymeric admixtures can be added to cement slurries to improve its fracture energy and silica flour to prevent strength retrogression. Therefore, the objective of the present study was to investigate the effect of the addition of different concentrations of polyurethane (5-25%) to cement slurries containing 40% BWOC silica flour. The resulting slurries were characterized using standard API (American Petroleum Institute) laboratory tests. In addition to them, the mechanical properties of the slurries, including elastic modulus and microhardness were also evaluated. The results revealed that density, free water and stability of the composite cement/silica/polyurethane slurries were within acceptable limits. The rheological behavior of the slurries, including plastic viscosity, yield strength and gel strength increased with the addition of 10% BWOC polyurethane. The presence of polyurethane reduced the fluid loss of the slurries as well as their elastic modulus. Composite slurries also depicted longer setting times due to the presence of the polymer. As expected, both the mechanical strength and microhardness of the slurries decreased with the addition of polyurethane. However, at high bottom hole temperatures, the strength of the slurries containing silica and polyurethane was far superior than that of plain cement slurries. In summary, the use of polyurethane combined with silica is an interesting solution to better adequate the mechanical behavior of cement slurries to heavy oil fields subjected to steam injection

Avaliação dos parâmetros genéticos em progênies de meio-irmãos de uma sub-população de milho composto Flint para resistência à lagarta-da-espiga Helicoverpa zea (Bod.)

Foram estudadas 100 progênies de meio-irmãos de uma sub-população de milho (Zea mays L.) Composto Flint com o objetivo de avaliar a resistência de genótipos à lagarta-da-espiga Helicoverpa zea (Bod.). Foram obtidos os valores de danos médios da lagarta-da-espiga de 1,14 cm de comprimento na espiga determinado pela escala de Widstrom e coeficiente de variação experimental (CVE) de 23,4%. Dos parâmetros genéticos avaliados, a estimativa de herdabilidade (h²) foi de 6%, variância genética (VG) de 0,0015 cm² e variância fenotípica (VF) de 0,025 cm² para danos de H. zea. No entanto, o comprimento da ponta da bráctea e compactação da bráctea alcançaram resultados de herdabilidade de 75% e 72% respectivamente. Essa sub-população de milho apresenta variabilidade genética suficiente para utilização em programas de melhoramento, sendo que a resistência à lagarta-da-espiga pode ser obtida através da melhoria dos caracteres morfológicos diretamente relacionados à praga, como a compactação e comprimento da bráctea.

Biologia populacional comparada de duas espécies de heliconius (Lepidoptera: Nymphalidae) em um ambiente sazonal de floresta atlântica do nordeste brasileiro

Tropical environments often face strong seasonal variations in climate, such as alternate periods of dry and rain, that may often be important influence in the annual X the organisms lives. Here we assess how population dynamics of two butterfly species (Heliconius erato and Heliconius mepomene) respond to environmental and seasonal variations. A mark-release-recapture study carried out in an Atlantic forest reserve, 15 Km from Natal, Rio Grande do Norte, Brazil, for 3 years, during the dry and rainy season, with three visits weekly done. Information such as species, wing lenght, site of capture, pollen load and phenotype (number of spots) (in H. erato only) were noted for each capture. Seasonal variation exists in capture rates of the two species, with great capture rates during the rainy season. Despite finding differences in the mean density of individuals of the two species among the different collection areas, this difference was only significant between floodplain and central areas, and no influence of seasonality was observed in the mean density between the areas. Seasonality in wing size was only observed for H. erato, with larger wings during the rainy season. Females carried larger pollen loads than males both species, but species were similar. Only males differed seasonally, with larger pollen loads during the rainy season. The distribution of the number of wing spots did not vary between the dry and rainy seasons, and the number of spots in males and females was similar. Therefore, we conclude that there was a strong influence of seasonal variation in the population dynamic of the two Heliconius species, as well as in several aspects of their biology

O Bumba meu boi como fenômeno estético

Cette étude propose d'articuler une discussion entre les définitions de corps, esthétique et éducation, tout en les plaçant dans le scénario des danses traditionnelles, surtout, le Bumba-meu-boi de l'État du Maranhão. On part de la proposition selon laquelle le Bumba-meu-boi ainsi que d'autres réjouissances traditionnelles, réunissent des éléments constitutifs qui se traduisent en langage esthétique et celui-ci exprime, par le biais des corps qui le cultivent, se constitue aussi, tout comme expression éducative des formes d'être et de vivre en société, dans l'espace et dans le temps, créant et récréant des structures, de modes d'être et de faire des sujets sociaux. À travers le chant, la danse, les actions organisatrices et d'autres aspects, on établit différentes stratégies de lecture du monde; tout en se mouvementant, se réorganisant, se renseignant à sur l'ambiance et de soi même. La recherche a, comme configuration méthodologique l'approche qualitative phénoménologique, dont la trajectoire du phénomène situé a été développée à partir des descriptions de l'expérience vécue par l'auteur dans le monde-vie du Bumba-meu-boi da Liberdade siégé à São Luis do Maranhão. C'est, donc, avec la compréhension de l'esthétique phénoménologique que nous nous sommes identifiés pour l'élaboration de cette étude. Cette conception est en rapport avec le domaine de l'appréhension sensible vinculée à la relation de sens de l'homme avec le monde, avec soi-même et avec les autres. La thèse présente la production de connaissance en tant que cathégorie esthétique et le phénomène éducatif configuré dans la condition corporelle de l'être humain. Nous comprenons que, dans l'expérience vécue et construite dans le scénario du Bumba-meu-boi, il y a une éducation qui se configure dans la plasticité du corps, dans sa capacité de donner des sens et de construire de significations

Construtivismo de marco teórico-pedagógico a grife: um estudo a partir das mensagens veiculadas na internet

This thesis is resulted of a research on propagated the social representations of constructivism in the Internet, which as had estimated basic the idea of Moscovici (1961) of that the media it has determinative paper in the popularization of the scientific theories, in formation e propagation of the social representations and in the construction of behaviors human beings. Understanding the Internet as latest space of circulation of social communications, therefore, privileged field (and still not explored) for studies of social representations, we choose this half midiático as investigative field of our research, it if it constitutes in the "great ocean of the new informational planet" (LEVY, 2000, p. 126), besides making possible the interaction with different forms of images, different individuals, different ' world ', configuring itself as important space of symbolic production e of analysis of the representational process in the world contemporary. Based in these questions, we trace as objective to analyze the circulating speech propagated on-line on the constructivism, searching to apprehend the social representations shared the respect. This objective was constructed in face of the insertion of the theory constructivist in the educational way has two decades more than, as well as of its consolidation as reference in different social contexts, mainly in midiático. The question that directed the research was: as this theory obtains to penetrate in some layers of our society, to influence the world readings e the behaviors of different people? That modifications it suffers in this trajectory and which the paper of the Internet in this process? The corpus of the research was constituted of the substances on the theory found in the Internet, in pages in Portuguese of Google, in the period of 27 of July of 2004 the 17 of August of 2004. The data they had been analyzed on the basis of the project of analysis of content elaborated for Moscovici (1961) and in the estimated theoreticians of the social communication, in special of the hypermedia. The results had disclosed that the Internet participates of determinative form in the process of popularization of the constructivism theory, not only spreading out its estimated theoretician- methodological for the domain public (diffusion), but propagating positive beliefs and images of its postulates (propagation) and using them it service of interests politicians e financiers (propaganda). The popularization of the constructivism in the Internet and social representations of this theory propagated configure one process in which the theory passes of pedagogical theoretical landmark for grief, assuming a commercial character extremely and the status of solution for problems of the education and the society, stirring up attitudes and behaviors in public, most general possible, that comes to take care of to the interests politicians e marketing. Recognizing the diversity, the permanent renewal of information and the negotiation of directions gifts in the Internet, as well as the innumerable ones forms of access to the information found by it, we consider results of the research as fruits of the inherent characteristics to this way midiático, to the time where we call the attention for relativity these results, for the plasticity of knowing them and sensible propagated on-line e for the great challenge that the hypermedia imposes to the study of communication phenomena, of the social representations and in educational quarrels and for the necessity of new research that they investigate the forms of socialization of the information and communication propitiated by hypermedia and its implications in the construction of the symbolic universes and in practical social

Weak phenotypic reversion of ivermectin resistance in a field resistant isolate of Haemonchus contortus by verapamil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Marcadores RAPD para detecção de resistência à ferrugem-asiática-da-soja

Os objetivos deste trabalho foram confirmar a herança da resistência da PI 459025 (Rpp4) à ferrugem-asiática-da-soja e identificar marcadores moleculares do tipo RAPD, ligados a este gene de resistência, em populações de soja. Pelo cruzamento dos genitores contrastantes PI 459025 x Coodetec 208 obteve-se uma população, cujas populações das gerações F2 e F2:3 foram artificialmente infectadas e avaliadas quanto à reação ao fungo Phakopsora pachyrhizi, pelo tipo de lesão (RB - resistente e TAN - suscetível). Com os resultados da avaliação fenotípica, dois bulks foram obtidos com DNA de plantas homozigóticas resistentes e suscetíveis, respectivamente, pela análise de bulks segregantes. de 600 iniciadores RAPD aleatórios, foram identificados três com fragmentos polimórficos entre os bulks e parentais contrastantes quanto à resistência. Pela análise do qui-quadrado, confirmaram-se: a herança monogênica, com dominância completa quanto à resistência ao patógeno, e a segregação 3:1 para a presença de banda dos três marcadores. Os três marcadores são ligados respectivamente a 5,1, 6,3 e 14,7 cM de distância do loco de resistência, em fase de repulsão no grupo de ligação G, o que foi confirmado pela utilização do marcador microssatélite Satt288. Estes marcadores são promissores na seleção assistida para resistência à ferrugem-asiática-da-soja.

Avaliação de populações de maracujazeiro-doce (Passiflora alata Curtis) obtidas de polinização aberta

Catorze características agronômicas de cinco populações de maracujazeiro-doce (Passiflora alata Curtis) foram avaliadas em Jaboticabal-SP, no período de abril de 2000 a março de 2001. Número de frutos por planta (NF), número de sementes/fruto (NS), massa do fruto (MF) e produção (PRO) foram caracteres que apresentaram os mais elevados índices de variabilidade entre plantas, possibilitando, assim, a seleção de plantas superiores quanto a estes caracteres. Médias dos caracteres produção (PRO), número de frutos/planta (NF), espessura da casca (EC), número de sementes/fruto (NS) e rendimento em polpa (%P), analisadas pelo teste de Tukey, a 5% de probabilidade, não apresentaram diferença significativa entre as populações. Observou-se considerável variabilidade entre plantas e baixa variabilidade entre as populações nestes caracteres.