The relationship between kurtosis- and envelope-based indexes for the diagnostic of rolling element bearings

The coupling of kurtosis based-indexes and envelope analysis represents one of the most successful and widespread procedures for the diagnostics of incipient faults on rolling element bearings. Kurtosis-based indexes are often used to select the proper demodulation band for the application of envelope-based techniques. Kurtosis itself, in slightly different formulations, is applied for the prognostic and condition monitoring of rolling element bearings, as a standalone tool for a fast indication of the development of faults. This paper shows for the first time the strong analytical connection which holds for these two families of indexes. In particular, analytical identities are shown for the squared envelope spectrum (SES) and the kurtosis of the corresponding band-pass filtered analytic signal. In particular, it is demonstrated how the sum of the peaks in the SES corresponds to the raw 4th order moment. The analytical results show as well a link with an another signal processing technique: the cepstrum pre-whitening, recently used in bearing diagnostics. The analytical results are the basis for the discussion on an optimal indicator for the choice of the demodulation band, the ratio of cyclic content (RCC), which endows the kurtosis with selectivity in the cyclic frequency domain and whose performance is compared with more traditional kurtosis-based indicators such as the protrugram. A benchmark, performed on numerical simulations and experimental data coming from two different test-rigs, proves the superior effectiveness of such an indicator. Finally a short introduction to the potential offered by the newly proposed index in the field of prognostics is given in an additional experimental example. In particular the RCC is tested on experimental data collected on an endurance bearing test-rig, showing its ability to follow the development of the damage with a single numerical index.

Report on a workshop to investigate the current status of environmental bio-acoustic monitoring

This workshop was supported by the Australian Centre for Ecological Analysis and Synthesis (ACEAS, http://www.aceas.org.au/), a facility of the Australian Government-funded Terrestrial Ecosystem Research Network (http://www.tern.org.au/), a research infrastructure facility established under the National Collaborative Research Infrastructure Strategy and Education Infrastructure Fund - Super Science Initiative, through the Department of Industry, Innovation, Science, Research and Tertiary Education. Hosted by: Queensland University of Technology, Brisbane, Queensland. (QUT, http://www.qut.edu.au/) Dates: 8-11 May 2012 Report Editors: Prof Stuart Parsons (Uni. Auckland, NZ) and Dr Michael Towsey (QUT). This report is a compilation of notes and discussion summaries contributed by those attending the Workshop. They have been assembled into a logical order by the editors. Another report (with photographs) can be obtained at: http://www.aceas.org.au/index.php?option=com_content&view=article&id=94&Itemid=96

The role of common but differentiated responsibility in the 2020 climate regime

The principle of common but differentiated responsibility (CBDR) will play a role in the 2020 Climate Regime. This Article starts by examining differential treatment within the international legal order, finding that it is ethically and practically difficult to implement an international climate instrument based on formal equality. There is evidence of state parties accepting differential responsibilities in a number of areas within the international legal order and the embedding of CBDR in the United Nations Framework Convention on Climate Change (UNFCCC), means that that differential commitments will lie at the heart of the 2020 climate regime. The UNFCCC applies the implementation method of differentiation, while the Kyoto Protocol applies both the obligation and implementation method of differentiation. It is suggested that the implementation model will be the differentiation model retained in the 2020 climate agreement. The Parties’ submissions under the Durban Platform are considered in order to gain an understanding of their positions on CBDR. While there are areas of contention including the role of principles in shaping obligations and the ongoing legal status of Annex I and Non-Annex I distinction, there is broad consensus among the parties in favour of differentiation by implementation with developed and major economies undertaking Quantified Emission Limitation and Reduction Objectives (economy wide targets) and developing countries that are not major economies undertaking sectoral targets.

The epidemiology of basal cell carcinoma

Basal cell carcinoma (BCC) is a skin cancer of particular importance to the Australian community. Its rate of occurrence is highest in Queensland, where 1% to 2% of people are newly affected annually. This is an order of magnitude higher than corresponding incidence estimates in European and North American populations. Individuals with a sun-sensitive complexion are particularly susceptible because sun exposure is the single most important causative agent, as shown by the anatomic distribution of BCC which is in general consistent with the levels of sun exposure across body sites. A distinguishing feature of BCC is the occurrence of multiple primary tumours within individuals, synchronously or over time, and their diagnosis and treatment costs contribute substantially to the major public health burden caused by BCC. A primary knowledge gap about BCC pathogenesis however was an understanding of the true frequency of multiple BCC occurrences and their body distribution, and why a proportion of people do develop more than one BCC in their life. This research project sought to address this gap under an overarching research aim to better understand the detailed epidemiology of BCC with the ultimate goal of reducing the burden of this skin cancer through prevention. The particular aim was to document prospectively the rate of BCC occurrence and its associations with constitutional and environmental (solar) factors, all the while paying special attention to persons affected by more than one BCC. The study built on previous findings and recent developments in the field but set out to confirm and extend these and propose more adequate theories about the complex epidemiology of this cancer. Addressing these goals required a new approach to researching basal cell carcinoma, due to the need to account for the phenomenon of multiple incident BCCs per person. This was enabled by a 20 year community-based study of skin cancer in Australians that provided the methodological foundation for this thesis. Study participants were originally randomly selected in 1986 from the electoral register of all adult residents of the subtropical township of Nambour in Queensland, Australia. On various occasions during the study, participants were fully examined by dermatologists who documented cumulative photodamage as well as skin cancers. Participants completed standard questionnaires about skin cancer-related factors, and consented to have any diagnosed skin cancers notified to the investigators by regional pathology laboratories in Queensland. These methods allowed 100% ascertainment of histologically confirmed BCCs in this study population. 1339 participants had complete follow-up to the end of 2007. Statistical analyses in this thesis were carried out using SAS and SUDAAN statistical software packages. Modelling methods, including multivariate logistic regressions, allowed for repeated measures in terms of multiple BCCs per person. This innovative approach gave new findings on two levels, presented in five chapters as scientific papers: 1. Incidence of basal cell carcinoma multiplicity and detailed anatomic distribution: longitudinal study of an Australian population The incidence of people affected multiple times by BCC was 705 per 100,000 person years compared to an incidence rate of people singly affected of 935 per 100,000 person years. Among multiply and singly affected persons alike, site-specific BCC incidence rates were far highest on facial subsites, followed by upper limbs, trunk, and then lower limbs 2. Melanocytic nevi and basal cell carcinoma: is there an association? BCC risk was significantly increased in those with forearm nevi (Odds Ratios (OR) 1.43, 95% Confidence Intervals (CI) 1.09-1.89) compared to people without forearm nevi, especially among those who spent their time mainly outdoors (OR 1.6, 95%CI 1.1-2.3) compared to those who spent their time mainly indoors. Nevi on the back were not associated with BCC. 3. Clinical signs of photodamage are associated with basal cell carcinoma multiplicity and site: a 16-year longitudinal study Over a 16-year follow-up period, 58% of people affected by BCC developed more than one BCC. Among these people 60% developed BCCs across different anatomic sites. Participants with high numbers of solar keratoses, compared to people without solar keratoses, were most likely to experience the highest BCC counts overall (OR 3.3, 95%CI 1.4-13.5). Occurrences of BCC on the trunk (OR 3.3, 95%CI 1.4-7.6) and on the limbs (OR 3.7, 95%CI 2.0-7.0) were strongly associated with high numbers of solar keratoses on these sites. 4. Occurrence and determinants of basal cell carcinoma by histological subtype in an Australian community Among 1202 BCCs, 77% had a single growth pattern and 23% were of mixed histological composition. Among all BCCs the nodular followed by the superficial growth patterns were commonest. Risk of nodular and superficial BCCs on the head was raised if 5 or more solar keratoses were present on the face (OR 1.8, 95%CI 1.2-2.7 and OR 4.5, 95%CI 2.1-9.7 respectively) and similarly on the trunk in the presence of multiple solar keratoses on the trunk (OR 4.2, 95%CI 1.5-11.9 and OR 2.2, 95%CI 1.1-4.4 respectively). 5. Basal cell carcinoma and measures of cumulative sun exposure: an Australian longitudinal community-based study Dermal elastosis was more likely to be seen adjacent to head and neck BCCs than trunk BCCs (p=0.01). Severity of dermal elastosis increased on each site with increasing clinical signs of cutaneous sun damage on that site. BCCs that occurred without perilesional elastosis per se, were always found in an anatomic region with signs of photodamage. This thesis thus has identified the magnitude of the burden of multiple BCCs. It does not support the view that people affected by more than one BCC represent a distinct group of people who are prone to BCCs on certain body sites. The results also demonstrate that BCCs regardless of site, histology or order of occurrence are strongly associated with cumulative sun exposure causing photodamage to the skin, and hence challenge the view that BCCs occurring on body sites with typically low opportunities for sun exposure or of the superficial growth pattern are different in their association with the sun from those on typically sun-exposed sites, or nodular BCCs, respectively. Through dissemination in the scientific and medical literature, and to the community at large, these findings can ultimately assist in the primary and secondary prevention of BCC, perhaps especially in high-risk populations.

A comparison of the gas phase acidities of phospholipid headgroups: Experimental and computational studies

Proton-bound dimers consisting of two glycerophospholipids with different headgroups were prepared using negative ion electrospray ionization and dissociated in a triple quadrupole mass spectrometer. Analysis of the tandem mass spectra of the dimers using the kinetic method provides, for the first time, an order of acidity for the phospholipid classes in the gas phase of PE < PA << PG < PS < PI. Hybrid density functional calculations on model phospholipids were used to predict the absolute deprotonation enthalpies of the phospholipid classes from isodesmic proton transfer reactions with phosphoric acid. The computational data largely support the experimental acidity trend, with the exception of the relative acidity ranking of the two most acidic phospholipid species. Possible causes of the discrepancy between experiment and theory are discussed and the experimental trend is recommended. The sequence of gas phase acidities for the phospholipid headgroups is found to (1) have little correlation with the relative ionization efficiencies of the phospholipid classes observed in the negative ion electrospray process, and (2) correlate well with fragmentation trends observed upon collisional activation of phospholipid \[M - H](-) anions. (c) 2005 American Society for Mass Spectrometry.

The implementation of a guideline of care for patients with a Sengstaken-Blakemore tube in situ in a general intensive care unit using transitional change theory

The use of the Sengstaken–Blakemore tube as a life-saving treatment for bleeding oesophageal varices is slowly becoming the least preferred method possibly due to the potential complications associated with its placement. Nursing practice pertaining to the care of this patient group appears ad hoc and reliant on local knowledge and experience as opposed to recognised evidence of best practice. Therefore, this paper focuses on the application of Lewin's transitional change theory used to introduce a change in nursing practice with the application of a guideline to enhance the care of patients with a Sengstaken–Blakemore tube in situ within a general intensive care unit. This method identified some of the complexities surrounding the change process including the driving and restraining forces that must be harnessed and minimised in order for the adoption of change to be successful.

Assessing exposure to polybrominated diphenyl ethers (PBDEs) for workers in the vicinity of a large recycling facility

Increased levels of polybrominated diphenyl ethers (PBDEs) can occur particularly in dust and soil surrounding facilities that recycle products containing PBDEs. This may be the source of increased exposure for nearby workers and residents. To investigate, we measured PBDE levels in soil, office dust and blood of workers at the closest workplace (i.e. within 100m) to a large automotive shredding and metal recycling facility in Brisbane, Australia. The workplace investigated in this study was independent of the automotive shredding facility and was one of approximately 50 businesses of varying types within a relatively large commercial/industrial area surrounding the recycling facility. Concentrations of PBDEs in soils were at least an order of magnitude greater than background levels in the area. Congener profiles were dominated by larger molecular weight congeners; in particular BDE-209. This reflected the profile in outdoor air samples previously collected at this site. Biomonitoring data from blood serum indicated no differential exposure for workers near the recycling facility compared to a reference group of office workers, also in Brisbane. Unlike air, indoor dust and soil sample profiles, serum samples from both worker groups were dominated by congeners BDE-47, BDE-153, BDE-99, BDE-100 and BDE-183 and was similar to the profile previously reported in the general Australian population. Estimated exposures for workers near the industrial point source suggested indoor workers had significantly higher exposure than outdoor workers due to their exposure to indoor dust rather than soil. However, no relationship was observed between blood PBDE levels and different roles and activity patterns of workers on-site. These comparisons of PBDE levels in serum provide additional insight into the inter-individual variability within Australia. Results also indicate congener patterns in the workplace environment did not match blood profiles of workers. This was attributed to the relatively high background exposures for the general Australian population via dietary intake and the home environment.

The salt dependence of DNA recognition by NF-kappaB p50 : a detailed kinetic analysis of the effects on affinityand specificity

The binding kinetics of NF-kappaB p50 to the Ig-kappaB site and to a DNA duplex with no specific binding site were determined under varying conditions of potassium chloride concentration using a surface plasmonresonance biosensor. Association and dissociation rate constants were measured enabling calculation of the dissociation constants. Under previously established high affinity buffer conditions, the k a for both sequences was in the order of 10(7) M-1s-1whilst the k d values varied 600-fold in a sequence-dependent manner between 10(-1) and 10(-4 )s-1, suggesting that the selectivity of p50 for different sequences is mediated primarily through sequence-dependent dissociation rates. The calculated K D value for the Ig-kappaB sequence was 16 pM, whilst the K D for the non-specific sequence was 9.9 nM. As the ionic strength increased to levels which are closer to that of the cellular environment, the binding of p50 to the non-specific sequence was abolished whilst the specific affinity dropped to nanomolar levels. From these results, a mechanism is proposed in which p50 binds specific sequences with high affinity whilst binding non-specific sequences weakly enough to allow efficient searching of the DNA.

General self-efficacy influences affective task reactions during a work simulation : the temporal effects of changes in workload at different levels of control

This study investigated the effects of workload, control, and general self-efficacy on affective task reactions (i.e., demands-ability fit, active coping, and anxiety) during a work simulation. The main goals were: (1) to determine the extent general self-efficacy moderates the effects of demand and control on affective task reactions, and; (2) to determine if this varies as a function of changes in workload. Participants (N=141) completed an inbox activity under conditions of low or high control and within low and high workload conditions. The order of trials varied so that workload increased or decreased. Results revealed individuals with high general self-efficacy reported better demands-abilities fit and active coping as well as less anxiety. Three interactive effects were found. First, it was found that high control increased demands-abilities fit from trial 1 to trial 2, but only when workload decreased. Second, it was found that low efficacious individuals active coping increased in trial 2, but only under high control. Third, it was found that high control helped high efficacious individuals manage anxiety when workload decreased. However, for individuals with low general self-efficacy, neither high nor low control alleviated anxiety (i.e., whether workload increased or decreased over time).

The collision induced loss of carbon monoxide from deprotonated benzyl benzoate in the gas phase. An anionic 1,2-Wittig type rearrangement

The ion PhCO2--CHPh, upon collision activation, undergoes competitive losses of CO and CO2 of which the former process produces the base peak of the spectrum. Product ion and substituent effect (Hammett) studies indicate that PhCO2--CHPh cyclises to a deprotonated hydroxydiphenyloxirane which ring opens to PhCOCH(O-)Ph. This anion then undergoes an anionic 1,2-Wittig type rearrangement {through [PhCO- (PhCHO)]} to form Ph2CHO- and CO. The mechanism of the 1,2-rearrangement has been probed by an ab initio study [at MP4(SDTQ)/6-31++G(d,p) level] of the model system HCOCH2O- →; MeO- + CO The analogous system RCO2--CHPh (R = alkyl) similarly loses CO, and the migratory aptitudes of the alkyl R groups in this reaction are Bu′ > Me > Et ∼Pri). This trend correlates with the order of anion basicities (i.e. the order of ΔG○acid values of RH), supporting the operation of an anion migration process. The loss of CO2 from PhCO2--CHPh yields Ph2CH- as the anionic product: several mechanistic scenarios are possible, one of which involves an initial ipso nucleophilic substitution.

A biomechanical analysis of growing rods used in the management of early onset scoliosis

INTRODUCTION Managing spinal deformities in young children is challenging, particularly early onset scoliosis (EOS). Surgical intervention is often required if EOS has been unresponsive to conservative treatment particularly with rapidly progressive curves. An emerging treatment option for EOS is fusionless scoliosis surgery. Similar to bracing, this surgical option potentially harnesses growth, motion and function of the spine along with correcting spinal deformity. Dual growing rods are one such fusionless treatment, which aims to modulate growth of the vertebrae. The aim of this study was to ascertain the extent to which semiconstrained growing rods (Medtronic, Sofamor, Danek, Memphis, TN) with a telescopic sleeve component, reduce rotational constraint on the spine compared with standard "constrained / rigid" rods and hence potentially provide a more physiological mechanical environment for the growing spine. METHODS Six 40-60kg English Large White porcine spines served as a model for the paediatric human spine. Each spine was dissected into a 7 level thoracolumbar multi-segment unit (MSU), removing all non-ligamentous soft tissues and leaving 3cm of ribs either side. Pure nondestructive axial rotation moments of ±4Nm at a constant rotation rate of 8deg.s-1 were applied to the mounted MSU spines using a biaxial Instron testing machine. Displacement of each vertebral level was captured using a 3D motion tracking system (Optotrak 3020, Northern Digital Inc, Waterloo, ON). Each spine was tested in an un-instrumented state first and then with appropriately sized semi-constrained growing rods and rigid rods in alternating sequence. The rods were secured by multi-axial pedicle screws (Medtronic CD Horizon) at levels 2 and 6 of the construct. The range of motion (ROM), neutral zone (NZ) size and stiffness (Nm.deg-1) were calculated from the Instron load-displacement data and intervertebral ROM was calculated through a MATLAB algorithm from Optotrak data. RESULTS Irrespective of the order of testing, rigid rods significantly reduced the total ROM compared with semi-constrained rods (p<0.05) with in a significantly stiffer spine for both left and right axial rotation (p<0.05). Analysing the intervertebral motion within the instrumented levels 2-6, rigid rods showed reduced ROM compared with semi-constrained growing rods and compared with un-instrumented motion segments. CONCLUSION Semi-constrained growing rods maintain similar stiffness in axial rotation to un-instrumented spines, while dual rigid rods significantly reduce axial rotation. Clinically the effect of semi-constrained growing rods as observed in this study is that they would be expected to allow growth via the telescopic rod components while maintaining the axial flexibility of the spine, which may reduce occurrence of the crankshaft phenomenon.

A quantification of the interaction and spatial ordering in nano-arrays

This paper reports on the use of a local order measure to quantify the spatial ordering of a quantum dot array (QDA). By means of electron ground state energy analysis in a quantum dot pair, it is demonstrated that the length scale required for such a measure to characterize the opto-electronic properties of a QDA is of the order of a few QD radii. Therefore, as local order is the primary factor that affects the opto-electronic properties of an array of quantum dots of homogeneous size, this order was quantified through using the standard deviation of the nearest neighbor distances of the quantum dot ensemble. The local order measure is successfully applied to quantify spatial order in a range of experimentally synthesized and numerically generated arrays of nanoparticles. This measure is not limited to QDAs and has wide ranging applications in characterizing order in dense arrays of nanostructures.

Third harmonic generation of the surface wave in the semiconductor-metal slowing-down structure

A nonlinear process is considered of the surface wave third harmonics generation in a slowing-down semiconductor-metal structure. The process is conditioned by non-parabolicity of the charge carrier dispersion law. It is shown that in narrow-gap semiconducting materials it is necessary to account for the process together with the surface wave second harmonics generation conditioned by nonlinearity of quasi-hydrodynamics and the Maxwell equations. The conclusion is made that the third harmonies amplitude in narrow-gap semiconductors may exceed substantially the signal amplitude at the 3w frequency in a gas plasma and be of the same order with the surface waves second harmonies amplitude.

Metal artifacts from titanium and steel screws in CT, 1.5T and 3T MR images of the tibial Pilon: A quantitative assessment in 3D

Radiographs are commonly used to assess articular reduction of the distal tibia (pilon) fractures postoperatively, but may reveal malreductions inaccurately. While Magnetic Resonance Imaging (MRI) and Computed Tomography (CT) are potential 3D alternatives they generate metal-related artifacts. This study aims to quantify the artifact size from orthopaedic screws using CT, 1.5T and 3T MRI data. Three screws were inserted into one intact human cadaver ankle specimen proximal to and along the distal articular surface, then CT, 1.5T and 3T MRI scanned. Four types of screws were investigated: titanium alloy (TA), stainless steel (SS) (Ø = 3.5 mm), cannulated TA (CTA) and cannulated SS (CSS)(Ø = 4.0 mm, Ø empty core = 2.6 mm). 3D artifact models were reconstructed using adaptive thresholding. The artifact size was measured by calculating the perpendicular distance from the central screw axis to the boundary of the artifact in four anatomical directions with respect to the distal tibia. The artifact sizes (in the order of TA, SS, CTA and CSS) from CT were 2.0 mm, 2.6 mm, 1.6 mm and 2.0 mm; from 1.5T MRI they were 3.7 mm, 10.9 mm, 2.9 mm, and 9 mm; and 3T MRI they were 4.4 mm, 15.3 mm, 3.8 mm, and 11.6 mm respectively. Therefore, CT can be used as long as the screws are at a safe distance of about 2 mm from the articular surface. MRI can be used if the screws are at least 3 mm away from the articular surface except SS and CSS. Artifacts from steel screws were too large thus obstructed the pilon from being visualised in MRI. Significant differences (P < 0.05) were found in the size of artifacts between all imaging modalities, screw types and material types, except 1.5T versus 3T MRI for the SS screws (P = 0.063). CTA screws near the joint surface can improve postoperative assessment in CT and MRI. MRI presents a favourable non-ionising alternative when using titanium hardware. Since these factors may influence the quality of postoperative assessment, potential improvements in operative techniques should be considered.

Force-deformation properties of the human heel pad during barefoot walking

Introduction: The plantar heel pad is a specialized fibroadipose tissue that attenuates and, in part, dissipates the impact energy associated with heel strike. Although near maximal deformation of the heel pad has been shown during running, in vivo measurement of the deformation and structural properties of the heel pad during walking remains largely unexplored. This study employed a fluoroscope, synchronized with a pressure platform, to obtain force–deformation data for the heel pad during walking. Methods: Dynamic lateral foot radiographs were acquired from 6 male and 10 female adults (age, 45 ± 10 yrs; height, 1.66 ± 0.10 m; and weight, 80.7 ± 10.8 kg), while walking barefoot at preferred speeds. The inferior aspect of the calcaneus was digitized and the sagittal thickness and deformation of the heel pad relative to the support surface calculated. Simultaneous measurement of the peak force beneath the heel was used to estimate the principal structural properties of the heel pad. Results: Transient loading profiles associated with walking induced rapidly changing deformation rates in the heel pad and resulted in irregular load–deformation curves. The initial stiffness (32 ± 11 N.mm-1) of the heel pad was an order of magnitude lower than its final stiffness (212 ± 125 N.mm-1) and on average, only 1.0 J of energy was dissipated by the heel pad with each step during walking. Peak deformation (10.3 mm) approached that predicted for the limit of pain tolerance (10.7 mm). Conclusion: These findings suggest the heel pad operates close to its pain threshold even at speeds encountered during barefoot walking and provides insight as to why barefoot runners may adopt ‘forefoot’ strike patterns that minimize heel loading.