Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

ISOLATION AND PROPERTIES OF A BLOOD-COAGULATION FACTOR-X ACTIVATOR FROM THE VENOM OF KING COBRA (OPHIOPHAGUS HANNAH)

A specific blood coagulation factor X activator was purified from the venom of Ophiophagus hannah by gel filtration and two steps of FPLC Mono-Q column ion-exchange chromatography. It showed a single protein band both in sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) and alkaline polyacrylamide gel electrophoresis. The mol. wt was estimated to be 62,000 in non-reducing conditions and 64,500 in reducing conditions by SDS-PAGE. The isoelectric point was found to be pH 5.6. The enzyme had weak amidolytic activities toward CBS 65-25, but it showed no activities on S-2266, S-2302, thrombin substrate S-2238, plasmin substrate S-2251 or factor Xa substrate S-2222. It had no arginine esterase activity toward substrate benzoylarginine ethylester (BAEE). The enzyme activated factor X in vitro and the effect was absolutely Ca2+ dependent, with a Hill coefficient of 6.83. It could not activate prothrombin nor had any effect on fibrinogen and thus appeared to act specifically on factor X. The procoagulant activity of the enzyme was almost completely inhibited by serine protease inhibitors like PMSF, TPCK and soybean trypsin inhibitor; partially inhibited by L-cysteine. Metal chelator EDTA did not inhibit its procoagulant activity. These results suggest that the factor X activator from O. hannah venom is a serine protease.

AN ACTIVATOR OF BLOOD-COAGULATION FACTOR-X FROM THE VENOM OF BUNGARUS-FASCIATUS

A specific activator of blood coagulation factor X was purified from the venom of Bungarus fasciatus by gel filtration and by ion-exchange chromatography on a Mono-Q column (FPLC). It consisted of a single polypeptide chain, with a mel. wt of 70,000 in reducing and non-reducing conditions. The enzyme had an amidolytic activity towards the chromogenic substrates S-2266 and S-2302 but it did not hydrolyse S-2238, S2251 or S-2222, which are specific substrates for thrombin, plasmin and factor Xa, respectively. The enzyme activated factor X in vitro and the effect was Ca2+ dependent with a Hill coefficient of 7.9. As with physiological activators, the venom activator cleaves the heavy chain of factor X, producing the activated factor Xa alpha. The purified factor X activator from B. fasciatus venom did not activate prothrombin, nor did it cleave or clot purified fibrinogen. The amidolytic activity and the factor X activation activity of the factor X activator from B. fasciatus venom were readily inhibited by serine protease inhibitors such as diisopropyl fluorophosphate (DFP), phenylmethanesulfonyl fluoride (PMSF), benzamidine and by soybean trypsin inhibitor but not by EDTA. These observations suggest that the factor X activator from B. fasciatus venom is a serine protease. It therefore differs from those of activators obtained from Vipera russelli and Bothrops atrox venoms, which are metalloproteinases.

Characterization of a fibrinogen-clotting enzyme from Trimeresurus stejnegeri venom, and comparative study with other venom proteases

Trimeresurus stejnegeri venom, which contains TSV-PA (a specific plasminogen activator sharing 60-70% sequence homology with venom fibrinogen-clotting enzymes), also possesses fibrinogen-clotting activity in vitro. A fibrinogen-clotting enzyme (stejnobin) has been purified to homogeneity by gel filtration and ion-exchange chromatography on a Mono-Q column. It is a single-chain glycoprotein with a mol. wt of 44,000. The NH2-terminal amino acid sequence of stejnobin shows great homology with venom fibrinogen-clotting enzymes and TSV-PA. Like TSV-PA, stejnobin was able to hydrolyse several chromogenic substrates. Comparative study of substrate specificities of stejnobin and other venom proteases purified in our laboratory was carried out on five chromogenic substrates. Stejnobin clotted human fibrinogen with a specific activity of 122 NIH thrombin-equivalent units/mg protein. However, stejnobin did not act on other blood coagulation factors, such as factor X, prothrombin and plasminogen. Diisopropyl fluorophosphate and phenylmethanesulfonyl fluoride inhibited its activity, whereas ethylenediamine tetracetic acid had no effect on it, indicating that it is a serine protease. Although stejnobin showed strong immunological cross-reaction with polyclonal antibodies raised against TSV-PA, it was interesting to observe that, unlike the case of TSV-PA, these antibodies did not inhibit the amidolytic and fibrinogen-clotting activities of stejnobin. (C) 1998 Elsevier Science Ltd. All rights reserved.

Effects of Pallas' viper (Agkistrodon halys pallas) venom on blood coagulation and characterization of a prothrombin activator

The action of Pallas' viper (Agkistrodon halys pallas) venom on blood coagulation was examined in vitro and a strong anticoagulant effect was observed. This action was abolished after treatment with a specific inhibitor of phospholipase A(2) activity (p-bromophenacyl bromide), revealing a procoagulant action in low concentrations of treated venom (around 1 mu g/ml). The effect of the venom an haemostasis was further characterized by measuring its ability to activate purified blood coagulation factors. It is concluded that A. halys pallas venom contains prothrombin activation activity. A prothrombin activator (aharin) was purified from the venom by Sephadex G-75 gel filtration and ion-exchange chromatography on a Mono-Q column. It consisted of a single polypeptide chain, with a mol. wt of 63,000. Purified aharin possessed no amidolytic activity on chromogenic substrates. It did not act on other blood coagulation factors, such as factor X and plasminogen, nor did it cleave or clot purified fibrinogen. The prothrombin activation activity of aharin was readily inhibited by ethylenediamine tetracetic acid (a metal chelator), but specific serine protease inhibitors such as diisopropyl fluorophosphate and phenylmethanesulfonyl fluoride had no effect on it. These observations suggest that, like those prothrombin activators from Echis carinatus and Bothrops atrox venoms, the prothrombin activator from A. halys pallas venom is a metalloproteinase. (C) 1998 Elsevier Science Ltd. All rights reserved.

Development of low cost feed using local ingredients for culture of freshwater prawn, Macrobrachium rosenbergii in ponds

Two experiments were conducted to formulate and evaluate test diets using locally available ingredients to find out suitable diets for mono and polyculture of Macrobrachium rosenbergii in ponds. The first experiment was conducted from 1 July 2003 to 29 September 2003 in 12 experimental ponds each measuring 30 square meters behind the Fisheries Faculty Building, BAU campus, Mymensingh. Three experimental diets containing 30% protein were formulated using fish meal, meat and bone meal, mustard oilcake, sesame meal and rice bran and assigned to treatments 1, 2 and 3, respectively. A special shrimp feed (Starter-II) from Saudi-Bangla Fish Feed Ltd. was assigned to treatment 4 (Control). Each treatment had three replications. Juveniles of M. rosenbergii (2.90±0.81g) were stocked at the rate of 4/square meter. Prawns were fed three times daily at the rate of 15% of their body weight at the beginning, which was gradually reduced to 10% and 5% for the last two months. There was no significant (P>0.05) difference between the weight gains of prawns fed diets 1 and 4 (control), but they were significantly (P<0.05) higher than those of diets 2 and 3. The FCR values of diets ranged between 2.61 to 3.36 with diets 1 and 4 showing significantly (P<0.05) lower FCR values. The survival rate of prawns ranged between 68 to 78% with prawns fed diets 1 and 4 showing significantly higher survival rate. The production of prawn ranged from 921 to 1,428 kg/ha/90 days and diet 1 gave the highest production. Treatment 1 gave the highest net profit ofTk. 161,980/ha/90 days. The second experiment was conducted from December, 2003 to April, 2004 to see the growth of over wintered M. rosenbergii juveniles in polyculture with indigenous major carps (catla and rohu) in ponds using formulated diets. Three isoenergetic experimental diets formulated using fish meal, meat and bone meal, mustard oil cake, rice bran, wheat bran and molasses, and a shrimp feed 'Golda special feed' from Saudi-Bangla Fish Feed Ltd. were assigned to treatments 1, 2, 3 and 4 (control), respectively, each treatment had two replications. Eight experimental ponds each measuring 80 square meters in the Field Laboratory Complex of the Faculty of Fisheries, BAU campus, Mymensingh were used. The mean initial weights of M. rosenbergii, catla and rohu were 1.60±0.01, 30.0±0.09 and 25.0±0.08 g, respectively. A total of 160 fish and prawn (20,000/ha) were stocked in each pond at the ratio of 2:1:1 (prawn: catla: rohu). Fish were fed at the rate of 3-5% of their body weight. Prawns fed diet 1, 2 and 4 showed higher weight gains compared to diet 3. The weight gain of catla was significantly higher in T1 while in case of rohu was higher in T1 and T4, respectively. There were no significant differences (P>0.05) in the survival rate of fish as obtained from different treatments. The overall total fish production ranged from 2196 to 2679 kg/ha/5 months. The highest production and the highest profit (Tk. 56,531/ha/5 months) was obtained from T1 and the lowest (Tk. 24,932/ha/5 months) from T4.

Tensile strength properties of polyethylene netting twines under exposure to out-door and artificial UV radiation

Photodegradation of three types of polyethylene twines namely, polyethylene fibrillated tape twine, polyethylene flat tape twine and polyethylene monofilament twines were studied by exposing them to sunlight and artificial UV radiation. The percentage residual strength varied in the samples, the monofilament with the highest residual strength followed by fibrillated tape twine and flat tape twine. A plot of the difference between the breaking strengths of the fibrillated tape twine and the mono filament twines against any given period of exposure exhibited a linear relationship

Polyculture of milkfish (Chanos chanos) and tiger prawn (Penaeus monodon Fab.) with and without supplemental feeding

Twelve 1,000 m super(2) earthen ponds were used to compare the growth rates, survival and production of milkfish (Chanos chanos)) and prawn (Penaeus monodon ) in monoculture and polyculture systems in shallow brackishwater ponds and without supplemental feeding. The low production and survival rates obtained were attributed to the lack of natural food; the high salinity during the first month of culture could be one of the causes of the high mortality of prawn observed in both mono and polyculture systems. Although the results of the trial were not ecouraging, it is possible that high yields may be obtained from the combination of the 2 species given enough natural food and favourable water conditions.

Impact of common carp, Cyprinus carpio (L.) and Nile tilapia, Oreochromis niloticus (L.) on arthropods population, zoobenthos and weeds in rice-fish culture

An experiment was carried out in the fields of the Agronomy Field Laboratory, Bangladesh Agricultural University, Mymensingh, Bangladesh to determine the impact of common carp (Cyprinus carpio) and tilapia (Oreochromis niloticus) culture on arthropod population, zoobenthos and weeds of rice field. The treatments were: (1) rice combined with mono sex tilapia, (2) rice combined with common carp, (3) rice combined with a mixed culture of mono sex tilapia and common carp and (4) rice alone. It was observed that tilapia significantly reduced the number of arthropods, green leafhoppers and white leafhoppers in the rice-fish production systems. Benthos analysis revealed significant effects of fish culture on the abundance of molluscs, oligochaete worms and chironomid larvae. Lowest number of benthos was obtained in the treatments with common carp and significant reduction of the weed biomass was observed, especially in the tilapia containing plots. Based on the results of the study it can be suggested that common carp may play an important role in controlling of benthic organisms, while tilapia might be more effective to control terrestrial arthropods and weeds.

Suitable stocking density of tilapia in an aquaponic system

An aquaponic system was studied through the integrated culture of mono-sex GIFT and two types of vegetables viz. morning glory, Ipomoea reptans and taro, Colocasia esculenta in a recirculating system for 15 weeks. Tilapia fry of uniform size of 0.76 g were released in three treatments (stocking densities): 106 fish/m³ (T1), 142 fish/m³ (T2) and 177 fish/m³ (T3) to assess the effect of stocking density on the growth performance of fish. Fish were fed with a commercial feed containing 25% protein. Weight gain (g) of tilapia ranged from 19.41 to 32.67 g and was inversely related with stocking density. Percent weight gain varied between 2553.99 and 4298.68% and was significantly different among the treatments. SGR ranged from 3.09 to 3.59% per day and varied significantly. FCR varied from 2.19 to 2.69 and had a positive correlation with stocking density. The highest survival rate (%) was achieved in T1 (99%) followed by T2 (98%) and T3 (96%). Production of fish ranged from 3.43 to 3.52 kg/m³ and was inversely related with stocking density. The present study demonstrated that 106 fish/m³ was the best stocking density in terms of growth, food conversion ratio, survival and production for tilapia culture in the aquaponic system.

The effect of Rosmarinus officinalis and Zataria multiflora extracts on the stability of poly unsaturated fatty acids in frozen silver carp minced

The purpose of this study, Evaluation the effect of Rosmarinus officinalis and Thymus vulgaris extracts on the stability of poly unsaturated fatty acids in frozen Silver carp minced. Treatments include: Treatment 1 - Control: frozen meat packaged in conventional Treatment 2: Frozen Silver carp minced+Thyme 300 mg/kg in normal packaging Treatment 3: Frozen Silver carp minced+Rosemary 200 mg/kg in normal packaging Treatment 4: Frozen Silver carp minced+Rosemary compound (100 mg/kg) and Thyme (100 mg/kg) in normal packaging After rapid freezing of samples in the spiral freezer by individual quick freezing method, to maintain the cold temperature (-18) °C were transferred. Sampling and measurements to determine the fatty acid profile of the zero phase beginning in the first month and then every ten days, and 15 days in the second month of the third month after the monthly test. Identifying, defining and measuring the fatty acid profile by gas chromatography was performed. In this study, levels of both saturated and unsaturated fatty acids in three experimental and one control were identified as follows: A: saturated fatty acids: Meristic C14: 0/Palmitic C16: 0/Hepta decaenoic C17: 0/Stearic C18: 0/Arashidic C20: 0/B:Mono unsaturated fatty acids: palmitoleic C16: 1-W7/Oleic C18: 1-W9/Gadoleic C20: 1-W9 C:Poly unsaturated fatty acids: Linoleic C18: 2-W6/α-Linolenic C18: 3-W3 D:High unsaturated fatty acids: Arachidonic C20: 4-W6 Eicosapentaenoic acid C20: 5-EPA/W3 Docosahexaenoic C22: 6-DHA/W3 Results of this study was to determine, Thyme and rosemary extracts containing silver carp minced stored in freezing conditions, Stability of different types of fatty acids, monounsaturated fatty acids, poly-unsaturated fatty acids, omega-3 and omega-6 fatty acids are. So that none of the fatty acids measured were not significant 100% increase or decrease, While changes in the fatty acid oxidation during storage time is minimized. The results obtained from the fatty acid profiles and indicators of their and statistical tests show that treatment with rosemary extract More stable during storage (-18) ° C In comparison with the control and other treatments are shown; And at relatively low compared to other treatments and control samples oleic acid and linoleic acid, palmitic more. According to studies,in Silver carp minced that containing rosemary extract, end of the storage period of six months. Were usable, so even rosemary extract the shelf-life examples to increase more than six months.

Growth rates of Tilapia esculenta (Graham) and Tilapia zillii (Gervais) under cultivation in ponds at Nyegezi, Tanzania

Aquaculture in Tanzania is still on a subsistence level and most of the ponds are maintained as part time job. The ponds are too small, shallow and over crowded with stunted Tilapia spp. In the present paper the results of experiments conducted in ponds at Nyegezi with T. esculenta and T. zillii are presented. This was part of an overall project of developing techniques of fish cultures with Tilapia under the limited existing conditions at Nyegezi. In a mono - species culture experiement with Tilapia zillii in nine month's time an average size of 172.8 mm/115.0 g was attained. In another experiment with T. zillii and T. esculenta in thirteen month's time, T. zillii attained an average size of 180.2mm/106.6 g and T. esculenta 193.6 mm/118.8 g. In another experiment with intensive feeding schedule an average size of 179.3 mm/126.6 g was attained by T. zillii and 191.0 mm/125.0 g by T. esculenta in four month's time. A locally prepared supplimentary feed with local Brewery Waste and Fish Meal (10:1) was readily accepted by both species of Tilapia. T. zillii voraciously fed on Cabbage leaves, Cauliflower leaves, Chinese cabbage leaves, Cassava leaves and on the common weed Comalina sp. Though all the items mentioned above were readily accepted by T. zillii feeding with Comaltna sp. was the easiest and most convenient because of its availability. In an intensive feeding experiment with vegetable leaves/Comalina sp. and the locally prepared supplimentary feed the fishes attained table size in four months time. Cement cistens of 5 X 3 X 1½ m size could be conveniently used for breeding both species of Tilapia. T. zillii had semi adhesive eggs and they were deposited on the sides of the cement wall. The number of young ones in a brood ranged from 160 to 314 in T. esculenta and 687 to 4,356 in T. zillii.

Red-Green-Blue 2D tuneable liquid crystal laser devices

In this paper, we review our recent experimental work on coherent and blue phase liquid crystal lasers.We will present results on thin-film photonic band edge lasing devices using dye-doped low molar mass liquid crystals in self-organised chiral nematic and blue phases. We show that high Q-factor lasers can be achieved in these materials and demonstrate that a single mode output with a very narrow line width can be readily achievable in well-aligned mono-domain samples. Further, we have found that the performance of the laser, i.e. the slope efficiency and the excitation threshold, are dependent upon the physical parameters of the low molar mass chiral nematic liquid crystals. Specifically, slope efficiencies greater than 60% could be achieved depending upon the materials used and the device geometry employed. We will discuss the important parameters of the liquid crystal host/dye guest materials and device configuration that are needed to achieve such high slope efficiencies. Further we demonstrate how the wavelength of the laser can be tuned using an in-plane electric field in a direction perpendicular to the helix axis via a flexoelectric mechanism as well as thermally using thermochromic effects. We will then briefly outline data on room temperature blue phase lasers and further show how liquid crystal/lenslet arrays have been used to demonstrate 2D laser emission of any desired wavelength. Finally, we present preliminary data on LED/incoherent pumping of RG liquid crystal lasers leading to a continuous wave output. © 2009 SPIE.

Jetting behaviour of polymer solutions in drop-on-demand inkjet printing

The jetting of dilute polymer solutions in drop-on-demand printing is investigated. A quantitative model is presented which predicts three different regimes of behaviour depending upon the jet Weissenberg number Wi and extensibility of the polymer molecules. In regime I (Wi < ½) the polymer chains are relaxed and the fluid behaves in a Newtonian manner. In regime II (½ < Wi < L) where L is the extensibility of the polymer chain the fluid is viscoelastic, but the polymer do not reach their extensibility limit. In regime III (Wi > L) the chains remain fully extended in the thinning ligament. The maximum polymer concentration at which a jet of a certain speed can be formed scales with molecular weight to the power of (1-3ν), (1-6ν) and -2ν in the three regimes respectively, where ν is the solvent quality coefficient. Experimental data obtained with solutions of mono-disperse polystyrene in diethyl phthalate with molecular weights between 24 - 488 kDa, previous numerical simulations of this system, and previously published data for this and another linear polymer in a variety of “good” solvents, all show good agreement with the scaling predictions of the model.

Regimes of Polymer Behaviour in Drop-on-Demand Ink-Jetting

Three regimes of fast DoD jetting behaviour for solutions of mono-disperse linear polymers have been linked to the underlying polymer molecular chains and their fully extended length L in good solvents. This allows scaling laws in molecular weight to be predicted and applied to experimental jetting results from different DoD print heads. The higher extensional flows encountered in high speed jetting in viscous solvents can fully stretch linear molecules outside the nozzle, permitting jetting of higher polymer content than for purely elastic behaviour. These results are significant for DoD printing at raised jet speeds and will apply to any DoD print head jetting linear polymer solutions.