Reciclagem química de Polietileno utilizando Sílica Mesoporosa tipo SBA-15 avalizada por Termogravimetriae Espectrometria de Massas

The chemical recycling of polyolefins has been the focus of increasing attention owing potential application as a fuel and as source chemicals. The use of plastic waste contributes to the solution of pollution problems.The use of catalysts can enhance the thermal degradation of synthetic polymers, which may be avaliated by Themogravimetry (TG) and mass spectrometry (MS) combined techniques. This work aims to propose alternatives to the chemistry recycling of low-density polyethylene (LDPE) on mesoporous silica type SBA-15 and AlSBA-15.The mesoporous materials type SBA-15 and AlSBA-15 were synthesized through the hydrothermal method starting from TEOS, pseudobohemite, cloridric acid HCl and water. As structure template was used Pluronic P123. The syntheses were accomplished during the period of three days. The best calcination conditions for removal of the organic template (P123) were optimized by thermal analysis (TG/DTG) and through analyses of Xray diffraction (XRD), infrared spectroscopy (FT-IR), nitrogen adsorption and scanning electron microscopy (SEM) was verified that as much the hydrothermal synthesis method as the calcination by TG were promising for the production of mesoporous materials with high degree of hexagonal ordination. The general analysis of the method of Analog Scan was performed at 10oC/min to 500 oC to avoid deterioration of capillary with very high temperatures. Thus, with the results, we observed signs mass/charge more evident and, using the MID method, was obtained curve of evolution of these signals. The addition of catalysis produced a decrease in temperature of polymer degradation proportional to the acidity of the catalyst. The results showed that the mesoporous materials contributed to the formation of compounds of lower molecular weight and higher value in the process of catalytic degradation of LDPE, representing an alternative to chemical recycling of solid waste

Fatty acid composition of mid-trimester amniotic fluid in women of different ethnicities

Objective: To determine whether the fatty acid composition of mid-trimester amniotic fluid differs by ethnicity and pregnancy outcome. Methods: Fatty acid composition was analyzed by gas chromatography in 198 women undergoing amniocentesis at 15-19 weeks gestation. Cytokine levels were determined by ELISA in a subgroup of 52 subjects. Results: The major fatty acids detected were palmitic acid (31.8%) and stearic acid (31.5%). The n-6 polyunsaturated fatty acids (PUFA), linoleic acid (LA, 18: 2) and arachidonic acid (AA, 20: 4), were 11.3%, while the n-3 PUFA fatty acids, alpha linolenic acid (ALA, 18: 3) and docosahexaenoic acid (DHA, 22: 6), were 3.8% of the total. Palmitic acid was a higher percentage in Asians (40.5%) and Whites (34.5%) than in Blacks (22.2%) and Hispanics (23.7%) (p <= 0.0012). Oleic acid (18:1 n-9) was a higher percentage in Blacks (12.2%) and Hispanics (12.1%) than in Whites (9.2%) or Asians (7.5%) (<= 0.0002). LA and AA were higher in Blacks (9.0%, 5.4%) and Hispanics (8.6%, 4.1%) than in Whites (6.1%, 3.7%) and Asians (5.5%, 2.9%) (p <= 0.0002). DHA did not differ among the ethnic groups or according to pregnancy outcome. A reduced palmitic acid percentage was identified in the six women with preeclampsia (p = 0.0233). Tumor necrosis factor-alpha levels were inversely proportional to the palmitic acid percentage (p = 0.0275) and positively associated with the percentages of stearic (18:0) (p = 0.0132) and oleic (p = 0.0290) acids. Conclusions: Amniotic fluid fatty acid composition differed among the ethnic groups and may influence inflammatory mediator production and susceptibility to preeclampsia.

Association between IGF-I, IGF-IR and GHRH gene polymorphisms and growth and carcass traits in beef cattle

Molecular biology techniques are of help in genetic improvement since they permit the identification, mapping and analysis of polymorphisms of genes encoding proteins that act on metabolic pathways involved in economically interesting traits. The somatotrophic axis, which essentially consists of growth hormone releasing hormone (GHRH), growth hormone (GH), insulin-like growth factors I and II (IGF-I and IGF-II), and their associated binding proteins and receptors (GHRHR, GHR, IGF-IR and IGF-IIR), plays a key role in the metabolism and physiology of mammalian growth. The objectives of the present study were to estimate the allele and genotype frequencies of the IGF-I/SnaBI, IGF-IR/TaqI and GHRH/HaeIII gene polymorphisms in different genetic groups of beef cattle and to determine associations between these polymorphisms and growth and carcass traits. For this purpose, genotyping was performed on 79 Nellore animals, 30 Canchim (5/8 Charolais+3/8 Zebu) animals and 275 crossbred cattle originating from the crosses of Simmental (n=30) and Angus (n=245) sires with Nellore females. In the association studies, traits of interest were analyzed using the GLM procedure of SAS and least square means of the genotypes were compared by the Tukey test. Associations of IGF-I/SnaBI genotypes with body weight and subcutaneous backfat were significant (p < 0.05), and nearly significant for longissimus dorsi area (p=0.06), with the 1313 genotype being favorable compared to the AB genotype. No significant associations were observed between this polymorphism and weight gain or carcass yield (P > 0.05). The IGF-IR/TaqI and GHRH/HaeIII polymorphisms showed no association with production traits. (c) 2004 Elsevier B.V All rights reserved.

Structural description of humic substances from subtropical coastal environments using elemental analysis, FT-IR and C-13-solid state NMR data

Elemental composition and spectroscopic properties (FT-IR and CP/MAS C-13-NMR) of sedimentary humic substances (HS) from aquatic subtropical environments (a lake, an estuary and two marine sites) are investigated. Humic acids (HA) are relatively richer in nitrogen and in aliphatic chains than fulvic acids (FA) from the same sediments. Conversely, FA are richer in carboxylic groups and in ring polysaccharides than HA. Nitrogen is mostly present as amide groups and for lake and marine HS the FT-IR peaks around 1640 cm(-1) and 1540 cm(-1) identify polypeptides. Estuarine HS exhibit mixed continental-marine influences, these being highly influenced by site location. Overall, the data suggest that aquatic and mixed HS are more aliphatic than has been proposed in current models and also that amide linkages form an important part of their structural configuration.

A Survey of mid and large bodied mammals in Núcleo Caraguatatuba, Serra do Mar State Park, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Surface characterization of feldspathic ceramic using ATR FT-IR and ellipsometry after various silanization protocols

Objectives. This study characterized the feldspathic ceramic surfaces after various silanization protocols.Methods. Ceramic bars (2 mm x 4 mm x 10 mm) (N = 18) of feldpathic ceramic (VM7, VITA Zahnfabrik) were manufactured and finished. Before silane application, the specimens were ultrasonically cleaned in distilled water for 10 min. The ceramic specimens were randomly divided into nine groups (N = 2 per group) and were treated with different silane protocols. MPS silane (ESPE-Sil, 3M ESPE) was applied to all specimens and left to react at 20 degrees C for 2 min (G20). After drying, the specimens were subjected to heat treatment in an oven at 38 degrees C (G38), 79 degrees C (G79) or 100 degrees C (G100) for 1 min. Half of the specimens of each group were rinsed with water at 80 degrees C for 15 s (G20B, G38B, G79B, G100B). The control group (GC) received no silane. Attenuated total reflection infrared Fourier transform analysis (ATR FT-IR) was performed using a spectrometer. Thickness of silane layer was measured using a spectroscopic ellip-someter working in the lambda = 632.8 nm (He-Ne laser) at 70 degrees incidence angle. Surface roughness was evaluated using an optical profilometer. Specimens were further analyzed under the Scanning Electron Microscopy (SEM) to observe the topographic patterns.Results. ATR FT-IR analysis showed changes in Si-O peaks with enlarged bands around 940 cm(-1). Ellipsometry measurements showed that all post-heat treatment actions reduced the silane film thickness (30.8-33.5 nm) compared to G20 (40 nm). The groups submitted to rinsing in hot water (B groups) showed thinner silane films (9.8-14.4 nm) than those of their corresponding groups (without washing) (30.8-40 nm). Profilometer analysis showed that heat treatments (Ra approximate to 0.10-0.19 mu m; Rq approximate to 0.15-0.26 mu m) provided a smoother surface than the control group (Ra approximate to 0.48 mu m; Rq approximate to 0.65 mu m). Similar patterns were also observed in SEM images.Significance. Heat treatment after MPS silane application improved the silane layer network. Rinsing with boiling water eliminated the outmost unreacted regions of the silane yielding to thinner film thicknesses. (C) 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Simultaneous determination of Cu and Pb in fuel ethanol by graphite furnace AAS using tungsten permanent modifier with co-injection of Ir

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evaluation of Ir and Pd(NO3)(2)/Mg(NO3)(2) as Modifiers for the Simultaneous Determination of Mn, Ni, Pb, and Sb in Fuel Ethanol by Graphite Furnace MS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo eletroquímico de Fe[Fe(CN)5NO] em eletrodo de pasta de grafite

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação de chumbo em álcool combustível por voltametria de redissolução anódica utilizando um eletrodo de pasta de carbono modificado com resina de troca iônica Amberlite IR 120

Um método envolvendo a pré-concentração e redissolução anódica em condições de voltametria de pulso diferencial empregando um eletrodo de pasta de carbono modificado (EPCM) com uma resina de troca iônica Amberlite IR120 foi proposto para a determinação de íons chumbo em álcool combustível. O procedimento é baseado em um pico de oxidação do analito observado em -0,53 V(vs. Ag/AgCl) em solução de HCl. As melhores condições experimentais encontradas foram: 5% (m/m) da Amberlite IR120 para a construção do eletrodo, solução de HCl 0,1 mol L-1, velocidade de varredura de 10 mVs-1, tempo de pré-concentração de 15 min e amplitude de pulso de 100 mV. Utilizando essas condições, o EPCM apresentou uma resposta linear entre a corrente de pico anódica e a concentração de íons chumbo para o intervalo entre 9,9 x 10-9 e 1,2 x 10-6 mol L-1 e um limite de detecção de 7,2 x 10-9 mol L-1. Valores de recuperação entre 96 % e 102 % foram encontrados para amostras de álcool combustível enriquecidas com Pb2+ em níveis de 10-7 mol L-1. O efeito da presença de outros íons concomitantes sobre a resposta voltamétrica do eletrodo também foi avaliado.

Report on ticks collected in the Southeast and Mid-West regions of Brazil: analyzing the potential transmission of tick-borne pathogens to man

Foram coletados espécimes de carrapatos em 1993, 1996, 1997, e 1998, principalmente de animais selvagens e domésticos, nas Regiões Sudeste e Centro-oeste do Brasil. Nove espécies de Amblyommidae foram identificadas: Anocentor Nitens, Amblyomma cajennense, Amblyomma ovale, Amblyomma fulvum, Amblyomma striatum, Amblyomma rotundatum, Boophilus microplus, Boophilus annulatus e Rhipicephalus sanguineus. Analisou-se o potencial destas nove espécies de carrapatos como transmissores de patógenos para o homem. Um Flaviviridade Flavivirus foi isolado de espécimes de Amblyomma cajennense coletados de um capivara doente (Hydrochaeris hydrochaeris). Amblyomma cajennense é o transmissor principal da Rickettsia rickettsii (=R. rickettsi), o agente causador da febre maculosa no Brasil. Os mamíferos selvagens, principalmente capivaras e veados infestados por carrapatos vivem em próximo contato com gado, cavalos e cachorros, com quem compartilham os mesmos carrapatos, oferecendo risco de transmissão destas zoonoses silvestres aos animais domésticos e ao homem.

Evaluation of Ir, Ru, and W as permanent modifiers for the simultaneous determination of As, Bi, Pb, Sb, and Se in natural water by electrothermal atomic absorption spectrometry

Iridium-, Ru-, and W-coated platforms were prepared by thermal treatment of the transversely heated graphite atomizer and investigated for the simultaneous determination of As, Bi, Pb, Sb, and Se in tap water by electrothermal atomic absorption spectrometry. The maximum pyrolysis temperature for As and Bi increased in a modifier sequence W < Ru < Ir. For Pb, Sb, and Se, this sequence was W < Ru, It. Calculated characteristic masses in the presence of It, Ru, and W were 35, 33, and 35 pg for As; 63, 51, and 52 pg for Bi; 50, 32, and 34 pg for Pb; 40, 35, and 31 pg for Sb; and 39, 39, and 93 pg for Se, respectively. Ruthenium was elected as the optimum modifier.Repeatability of the measurements was typically < 6%. Recoveries of As, Bi, Pb, Sb, and Se added to tap water samples varied from 79 to 109%. Accuracy was also checked by analysis of five certified reference materials (CRMs) from the National Institute of Standards and Technology (NIST1640 - Trace Elements in Natural Water; NIST 1643d Trace Elements in Water) and High Purity Standards (Trace Metals in Drinking Water Standards, lots #812708, #591107, and #710710). A paired t-test showed that the results for the CRMs were in agreement at the 95% confidence level with the certified values. The graphite tube lifetime was about 650 firings. multi-element determination is particularly challenging due to the necessity of carefully optimizing compromise conditions.Based on the considerations listed above, the aim of this paper was to evaluate the behavior of Ir, Ru, and W as permanent modifiers for the simultaneous determination of As, Bi, Pb, Sb, and Se. The performance of the proposed procedure was also verified after the ETAAS analysis of tap waters and reference materials.

Electrochemical oxidation of an acid dye by active chlorine generated using Ti/Sn(1-x)Ir O-x(2) electrodes

The generation of active chlorine on Ti/Sn(1-x)Ir (x) O-2 anodes, with different compositions of Ir (x = 0.01, 0.05, 0.10 and 0.30 ), was investigated by controlled current density electrolysis. Using a low concentration of chloride ions (0.05 mol L-1) and a low current density (5 mA cm(-2)) it was possible to produce up to 60 mg L-1 of active chlorine on a Ti/Sn0.99Ir0.01O2 anode. The feasibility of the discoloration of a textile acid azo dye, acid red 29 dye (C.I. 16570), was also investigated with in situ electrogenerated active chlorine on Ti/Sn(1-x)Ir (x) O-2 anodes. The best conditions for 100% discoloration and maximum degradation (70% TOC reduction) were found to be: NaCl pH 4, 25 mA cm(-2) and 6 h of electrolysis. It is suggested that active chlorine generation and/or powerful oxidants such as chlorine radicals and hydroxyl radicals are responsible for promoting faster dye degradation. Rate constants calculated from color decay versus time reveal a zero order reaction at dye concentrations up to 1.0 x 10(-4) mol L-1. Effects of other electrolytes, dye concentration and applied density currents also have been investigated and are discussed.