Escape in a nonideal electro-mechanical system

In this work a particular system is investigated consisting of a pendulum whose point of support is vibrated along a horizontal guide by a two bar linkage driven from a DC motor, considered as a limited power source. This system is nonideal since the oscillatory motion of the pendulum influences the speed of the motor and vice-versa, reflecting in a more complicated dynamical process. This work comprises the investigation of the phenomena that appear when the frequency of the pendulum draws near a secondary resonance region, due to the existing nonlinear interactions in the system. Also in this domain due to the power limitation of the motor, the frequency of the pendulum can be captured at resonance modifying completely the final response of the system. This behavior is known as Sommerfeld effect and it will be studied here for a nonlinear system.

Magnesium hydroxide-based peroxide bleaching of high-brightness mechanical pulps

A high final brightness is desired in most paper and board products. This requires bleaching processes that are able to produce high-brightness pulps. Mechanical pulps are widely bleached for high brightness using alkaline hydrogen peroxide with traditional sodium hydroxide and sodium silicate as additives. With high doses however, peroxide bleaching causes high organic loads in the mill effluent and anionic trash carry-over to papermaking. To alleviate the problems that arise from the use of sodium-based additives in peroxide bleaching, interest in the use of alternative magnesium-based chemicals has increased. In this study, a new, technical high-purity magnesium hydroxide-based bleaching additive was evaluated on laboratory-scale, pilot-scale and mill-scale experiments and trials for its ability to produce a high brightness in peroxide bleaching without the known problems of sodium-based chemicals. The key findings of this study include: a high brightening potential of peroxide bleaching using the Mg(OH)2-based additive, significant reductions (40-70%) in all categories of environmental load, and cationic demand lowered by 60-70% in bleached pulp with no loss in strength properties or in sheet bulk. When used in TMP refiner bleaching, the Mg(OH)2-based additive resulted in savings in specific energy consumption and provided a good bleaching response.

[Energies]

Soitinnus: cembalo.

Action of laccase on mechanical softwood pulps

Träfibrernas naturliga egenskaper begränsar deras användning i många tillämpningar. Träfibrernas egenskaper kan modifieras genom att binda nya komponenter med önskade egenskaper till fiberns yta. DI Stina Grönqvist bevisade i sin avhandling att nya funktionella grupper kan bindas till ligninhaltiga träfibrer genom att aktivera ytligninet med lackasenzym. Resultaten kan utnyttjas till att förbättra de traditionella träfibrernas och fiberprodukternas egenskaper samt att hitta nya tillämpningar för träfibrerna. ”Om träfibrerna t.ex. modifieras så att de blir vattenavstötande kan de modifierade träfibrerna användas istället för plast i förpackningar” berättar Stina Grönqvist. Syftet med denna avhandling var att undersöka effekterna av lackasenzym på TMP (termomekanisk massa) och dess fraktioner. I Finland tillverkas TMP av gran och massan innehåller rikligt med lignin. När ytligninet på träfibrernas yta modifieras med hjälp av oxiderande enzymer, såsom lackas, bildas reaktiva radikaler i ligninen på fibrernas ytor. De bildade radikalerna kan utnyttjas till att binda komponenter med nya egenskaper till fiberytan. För att kunna utnyttja den fulla potentialen av den lackasbaserade modifieringsmetoden behövs mera information om så väl de faktorer som påverkar bildningen av radikaler som om mekanismerna hur de nya komponenterna binds till fibrerna ___________________________________ Puukuitujen luontaiset ominaisuudet rajoittavat niiden hyödyntämistä joissakin sovelluksissa. Ominaisuuksia voidaan kuitenkin muuttaa liittämällä kuidun pintaan uusia yhdisteitä. DI Stina Grönqvist osoitti väitöstyössään, että uusia kuitujen ominaisuuksia muuttavia funktionaalisia yhdisteitä voidaan sitoa ligniinipitoisiin puukuituihin aktivoimalla kuitujen pinnan ligniiniä lakkaasi-entsyymillä. Tutkimuksen tuloksia voidaan hyödyntää ligniinipitoisten puukuitujen ominaisuuksien parantamiseen ja jopa täysin uusien ominaisuuksien kehittämiseen. ”Jos kuituja muutetaan vettä hylkiväksi sitomalla kuituihin vettä hylkiviä yhdisteitä entsyymien avulla, voidaan puukuituja käyttää korvaamaan muovia pakkauksissa”, kertoo Stina Grönqvist. Väitöstyön kohteena oli TMP-massan eli kuumahiertämällä valmistetun mekaanisen puumassojen ja niiden fraktioiden muokkaaminen lakkaasi-entsyymillä (TMP, Thermomechanical pulp). Suomalainen TMP-massa valmistetaan kuusesta ja siinä on runsaasti muokkaamatonta ligniiniä. Kun puukuidun pinnan ligniiniä muokataan hapettavilla entsyymeillä, muodostuu kuidun pintaan reaktiivisia radikaaleja. Syntyneiden radikaalien avulla kuituihin voidaan liittää yhdisteitä, jotka antavat kuidulle uusia ominaisuuksia. Menetelmän tarjoamien mahdollisuuksien hyödyntämiseksi tarvitaan tietoa kuidun radikalisointiin ja yhdisteiden liittämiseen vaikuttavista tekijöistä.

Comparison study of two competing models of an all mechanical power transmission system

A comparison between two competing models of an all mechanical power transmission system is studied by using Dymola –software as the simulation tool. This tool is compared with Matlab/ Simulink –software by using functionality, user-friendliness and price as comparison criteria. In this research we assume that the torque is balanceable and transmission ratios are calculated. Using kinematic connection sketches of the two transmission models, simulation models are built into the Dymola simulation environment. Models of transmission systems are modified according to simulation results to achieve a continuous variable transmission ratio. Simulation results are compared between the two transmission systems. The main features of Dymola and MATLAB/ Simulink are compared. Advantages and disadvantages of the two softwares are analyzed and compared.

Mechanical design and analysis of modular active magnetic bearing test rig

Tässä työssä on tutkittu modulaarisen aktiivimagneettilaakeroidun koelaitteen mekaanista suunnittelua ja analysointia. Suurnopeusroottorin suunnittelun teoria on esitelty. Lisäksi monia analyyttisiä mallinnusmenetelmiä mekaanisten kuormitusten mallintamiseksi on esitelty. Koska kyseessä on suurnopeussähkökone, roottoridynamiikka ja sen soveltuvuus suunnittelussa on esitelty. Magneettilaakerien rakenteeseen ja toimintaan on tutustuttu osana tätä työtä. Kirjallisuuskatsaus nykyisistä koelaitteista esimerkiksi komponenttien ominaisuuksien tunnistamiseen ja roottoridynamiikan tutkimuksiin on esitelty. Työn rajauksena on konseptisuunnittelu muunneltavalle magneettilaakeroidulle (AMB) koelaitteelle ja suunnitteluprosessin dokumentointi. Muunneltavuuteen päädyttiin, koska se mahdollistaa erilaisten komponenttiasetteluiden testaamisen erilaisille magneettilaakerikokoonpanoille ja roottoreille. Pääpaino tässä työssä on suurnopeus induktiokoneen roottorin suunnittelussa ja mallintamisessa. Modulaaristen toimilaitteiden kuten magneettilaakerien ja induktiosähkömoottorin rakenne on esitelty ja modulaarisen rakenteen käytettävyyden hyödyistä koelaitekäytössä on dokumentoitu. Analyyttisiä ja elementtimenetelmään perustuvia tutkimusmenetelmiä on käytetty tutkittaessa suunniteltua suurnopeusroottoria. Suunnittelun ja analysoinnin tulokset on esitelty ja verrattu keskenään eri mallinnusmenetelmien välillä. Lisäksi johtopäätökset sähkömagneettisten osien liittämisen monimutkaisuudesta ja vaatimuksista roottoriin ja toimilaitteisiin sekä mekaanisten että sähkömagneettisten ominaisuuksien optimoimiseksi on dokumentoitu.

Microscopic variability in mechanical defence and herbivory response in microphyllous leaves of tropical herb species from Serra do Cipó, Brazil

Tropical high altitude grasslands present several species with both microphyllous and highly sclerophyllous leaves, and co-occur in specific soil patches, thus exposed to identical environments. In this article we describe herbivory among co-occurring microphyllous species in a tropical high altitude grassland ecosystem of Serra do Cipó, Minas Gerais state, and we tested the effect of variable anatomic traits on leaf herbivory patterns. Leaf anatomical traits were investigated for Baccharis imbricata Heering , Lavoisiera imbricata DC. and L. subulata Triana (focal species). Herbivory was measured from branches and leaves of individual plants and compared among co-occurring species within one multispecific shrub patch and among L. subulata individuals from this patch and an adjacent monospecific patch. For all present plant species and individuals we estimated the proportion of leaves with different levels of area lost. For the focal species, six leaves were sorted and taken for histological sectioning, in order to allow precise measures of defensive structures. Relative mean leaf area lost differed significantly among the six species found in the multispecific patch. Lavoisiera subulata individuals were more attacked in the multispecific than in the monospecific patch. Leaf margin protection traits in both B. imbricata and L. imbricata showed significant effect against herbivory. Data suggest that some anatomic traits have direct effect against herbivory but their effect are not clearly perceptible among branches within individual plants or among plants within the same species.

Presurgical ketoprofen, but not morphine, dipyrone, diclofenac or tenoxicam, preempts post-incisional mechanical allodynia in rats

The treatment of pain before it initiates may prevent the persistent pain-induced changes in the central nervous system that amplify pain long after the initial stimulus. The effects of pre- or postoperative intraperitoneal administration of morphine (2 to 8 mg/kg), dipyrone (40 and 80 mg/kg), diclofenac (2 to 8 mg/kg), ketoprofen (10 and 20 mg/kg), and tenoxicam (10 and 20 mg/kg) were studied in a rat model of post-incisional pain. Groups of 5 to 8 male Wistar rats (140-160 g) were used to test each drug dose. An incision was made on the plantar surface of a hind paw and the changes in the withdrawal threshold to mechanical stimulation were evaluated with Von Frey filaments at 1, 2, 6 and 24 h after the surgery. Tenoxicam was given 12 or 6 h preoperatively, whereas the remaining drugs were given 2 h or 30 min preoperatively. Postoperative drugs were all given 5 min after surgery. No drug abolished allodynia when injected before or after surgery, but thresholds were significantly higher than in control during up to 2 h following ketoprofen, 6 h following diclofenac, and 24 h following morphine, dipyrone or tenoxicam when drugs were injected postoperatively. Significant differences between pre- and postoperative treatments were obtained only with ketoprofen administered 30 min before surgery. Preoperative (2 h) intraplantar, but not intrathecal, ketoprofen reduced the post-incisional pain for up to 24 h after surgery. It is concluded that stimuli generated in the inflamed tissue, rather than changes in the central nervous system are relevant for the persistence of pain in the model of post-incisional pain.

Effect of ultrastructural features on mechanical properties of softwood fiber

The main objective of this study was to develop mathematical model capable to describe the effect of ultrastructural features on the longitudinal modulus of elasticity of softwood fiber. Another objective was to identify, based on ultrastructural features, a potential explanatory factor for the mechanical difference between Norway spruce and Scots pine fibers and to demonstrate its influence utilizing developed modelling tools. According to the literature, the main difference between the pine and spruce fibers is the pit structure, which is clearly different in these fibers. The spruce fiber contains a lot of tiny pits, whereas the pits of the pine fiber are larger and the total number of them is smaller. The effect of the pits on the longitudinal modulus of elasticity of fiber is studied with both the analytical and the numerical model. The results show that, although the spruce fiber seems to contain clearly more pits, larger pits appearing in the pine fiber turn out to have a stronger influence on the longitudinal modulus of elasticity of the fiber. The effect of local variation of microfibril angle which occurs near the pits seems to be minor. Moreover, the results suggest that spruce fibers may have higher ultimate strength due to the more uniform straining behavior.

Understanding the mechanisms of lung mechanical stress

Physical forces affect both the function and phenotype of cells in the lung. Bronchial, alveolar, and other parenchymal cells, as well as fibroblasts and macrophages, are normally subjected to a variety of passive and active mechanical forces associated with lung inflation and vascular perfusion as a result of the dynamic nature of lung function. These forces include changes in stress (force per unit area) or strain (any forced change in length in relation to the initial length) and shear stress (the stress component parallel to a given surface). The responses of cells to mechanical forces are the result of the cell's ability to sense and transduce these stimuli into intracellular signaling pathways able to communicate the information to its interior. This review will focus on the modulation of intracellular pathways by lung mechanical forces and the intercellular signaling. A better understanding of the mechanisms by which lung cells transduce physical forces into biochemical and biological signals is of key importance for identifying targets for the treatment and prevention of physical force-related disorders.

Inventive design and product development of a mechanical element

The thesis is dedicated to enhancement and development of a Mechanism in Company X in order to increase its key parameters and approve its workability. Current Mechanism model is described in details. The basis of various analysis, models and theories that are reflecting the working process of the Mechanism are included in the thesis. According to these three directions of enhancements are chosen: from mechanical, tribological and conceptual points of view. As the result the list of improvements is presented. The new models of Mechanism are built. The efficiency and lifetime value are obtained in accordance with corresponding estimations. The comparative analysis confirms the necessity of conducted changes. Recommendations for the Company X specialists are represented in the thesis. Proposals for deeper research are also suggested.

13CO2 recovery fraction in expired air of septic patients under mechanical ventilation

The continuous intravenous administration of isotopic bicarbonate (NaH13CO2) has been used for the determination of the retention of the 13CO2 fraction or the 13CO2 recovered in expired air. This determination is important for the calculation of substrate oxidation. The aim of the present study was to evaluate, in critically ill patients with sepsis under mechanical ventilation, the 13CO2 recovery fraction in expired air after continuous intravenous infusion of NaH13CO2 (3.8 µmol/kg diluted in 0.9% saline in ddH2O). A prospective study was conducted on 10 patients with septic shock between the second and fifth day of sepsis evolution (APACHE II, 25.9 ± 7.4). Initially, baseline CO2 was collected and indirect calorimetry was also performed. A primer of 5 mL NaH13CO2 was administered followed by continuous infusion of 5 mL/h for 6 h. Six CO2 production (VCO2) measurements (30 min each) were made with a portable metabolic cart connected to a respirator and hourly samples of expired air were obtained using a 750-mL gas collecting bag attached to the outlet of the respirator. 13CO2 enrichment in expired air was determined with a mass spectrometer. The patients presented a mean value of VCO2 of 182 ± 52 mL/min during the steady-state phase. The mean recovery fraction was 0.68 ± 0.06%, which is less than that reported in the literature (0.82 ± 0.03%). This suggests that the 13CO2 recovery fraction in septic patients following enteral feeding is incomplete, indicating retention of 13CO2 in the organism. The severity of septic shock in terms of the prognostic index APACHE II and the sepsis score was not associated with the 13CO2 recovery fraction in expired air.

Streptozotocin-induced mechanical hypernociception is not dependent on hyperglycemia

Since streptozotocin (STZ)-induced diabetes is a widely used model of painful diabetic neuropathy, the aim of the present study was to design a rational protocol to investigate whether the development of mechanical hypernociception induced by STZ depends exclusively on hyperglycemia. Male Wistar rats (180-200 g; N = 6-7 per group) received a single intravenous injection of STZ at three different doses (10, 20, or 40 mg/kg). Only the higher dose (40 mg/kg) induced a significant increase in blood glucose levels, glucose tolerance and deficiency in weight gain. However, all STZ-treated rats (hyperglycemic or not) developed persistent (for at least 20 days) and indistinguishable bilateral mechanical hypernociception that was not prevented by daily insulin treatment (2 IU twice a day, sc). Systemic morphine (2 mg/kg) but not local (intraplantar) morphine treatment (8 µg/paw) significantly inhibited the mechanical hypernociception induced by STZ (10 or 40 mg/kg). In addition, intraplantar injection of STZ at doses that did not cause hyperglycemia (30, 100 or 300 µg/paw) induced ipsilateral mechanical hypernociception for at least 8 h that was inhibited by local and systemic morphine treatment (8 µg/paw or 2 mg/kg, respectively), but not by dexamethasone (1 mg/kg, sc). The results of this study demonstrate that systemic administration of STZ induces mechanical hypernociception that does not depend on hyperglycemia and intraplantar STZ induces mechanical sensitization of primary sensory neurons responsive to local morphine treatment.

Mechanical cardiac remodeling and new-onset atrial fibrillation in long-term follow-up of subjects with chronic Chagas' disease

Atrial fibrillation (AF) affects subjects with Chagas' disease and is an indicator of poor prognosis. We investigated clinical, echocardiographic and electrocardiographic variables of Chagas' disease in a long-term longitudinal study as predictors of a new-onset AF episode lasting >24 h, nonfatal embolic stroke and cardiac death. Fifty adult outpatients (34 to 74 years old, 62% females) staged according to the Los Andes classification were enrolled. During a follow-up of (mean ± SD) 84.2 ± 39.0 months, 9 subjects developed AF (incidence: 3.3 ± 1.0%/year), 5 had nonfatal stroke (incidence: 1.3 ± 1.0%/year), and nine died (mortality rate: 2.3 ± 0.8%/year). The progression rate of left ventricular mass and left ventricular ejection fraction was significantly greater in subjects who experienced AF (16.4 ± 20.0 g/year and -8.6 ± 7.6%/year, respectively) than in those who did not (8.2 ± 8.4 g/year; P = 0.03, and -3.0 ± 2.5%/year; P = 0.04, respectively). In univariate analysis, left atrial diameter ≥3.2 cm (P = 0.002), pulmonary arterial hypertension (P = 0.035), frequent premature supraventricular and ventricular contraction counts/24 h (P = 0.005 and P = 0.007, respectively), ventricular couplets/24 h (P = 0.002), and ventricular tachycardia (P = 0.004) were long-term predictors of AF. P-wave signal-averaged ECG revealed a limited long-term predictive value for AF. In chronic Chagas' disease, large left atrial diameter, pulmonary arterial hypertension, frequent supraventricular and ventricular premature beats, and ventricular tachycardia are long-term predictors of AF. The rate of left ventricular mass enlargement and systolic function deterioration impact AF incidence in this population.