Effect of the curing conditions of concrete on the behaviour under freeze-thaw cycles*

The aim of this work is to relate the curing conditions of concrete and the addition of an air-entraining admixture with the damage caused by freeze–thaw cycles. In countries with a continental climate, the curing of concrete in summer is performed under climatic conditions of high temperature and low humidity, and during the winter the concrete suffers conditions of freeze–thaw, often accompanied by the use of de-icing salts. This paper shows the experimental results of the behaviour of concrete specimens cured under climatic summer conditions (high temperature and low humidity) and then subjected to freeze–thaw cycles. Curing of the specimens includes conditions of good and bad practice in relation to wetting and protection of the concrete. It also examines the effectiveness of using an air-entraining admixture in both cases. The experimental programme includes an evaluation of the mechanical properties of the concrete, the study of the cement hydration and the measurement of the volume and pore sizes of the concrete. These tests were performed before and after the application of the freeze–thaw cycles. The results obtained showed that the specimens without air-entraining admixture show a deterioration of mechanical properties after the freeze–thaw test. However, the inclusion of air bubbles benefits the behaviour of concrete against freeze–thaw cycles so even better mechanical properties after the test were observed. This anomalous behaviour is because the cement hydration process continues over the freeze–thaw tests, closing the pore structure. This aspect has been confirmed with the DTA and TG tests performed

Effect of Initial On-Site Curing on 28-Day Cylinder Strength

The initial curing of concrete specimens for quality assurance is addressed in different ways in testing standards, which often specify requirements that are difficult to meet in practice unless very costly initial curing chambers are available. The failure to meet these requirements in many areas of the world does not appear to result in adverse consequences. This study analyzed six initial curing temperature schemes, all with cycles similar to natural conditions to avoid the simplifications inherent in constant temperature curing. Three strengths of concrete and two initial curing times (24 and 72 hours) were used in this study. The findings showed that initial curing time had no effect on 28-day strength. The 28-day strength also proved to be resilient to maximum and minimum initial curing temperatures outside the limits stated in the standards considered in this study

Recubrimientos recomendables por razones de durabilidad, a disponer en estructuras de hormigón sometidas a la clase específica de exposición Qb (ataque químico de intensidad media)

Es una realidad cada vez más aceptada que la durabilidad del hormigón es una propiedad igual de importante que la resistencia mecánica o la estabilidad de volumen. No es el objeto del presente trabajo ahondar en las causas de esta evidencia sino en contribuir a hacer del diseño de la durabilidad una materia incorporada al quehacer diario de los técnicos y especialistas. Solo si la durabilidad de una estructura se puede proyectar y verificar, será posible conseguir vidas útiles con una cierta garantía o seguridad en que se alcanzarán los periodos de servicio que se especifiquen. En el diseño de la durabilidad se ha dedicado mucho tiempo en el pasado a aclarar los mecanismos de ataque (por ejemplo: por sulfatos o por reacción árido-álcali) o como realizar ensayos acelerados en estos casos y también en el caso concreto de la corrosión de la armadura. En el caso de la corrosión, la envergadura de los costes de reparaciones ha estimulado la publicación de modelos y ensayos que, si bien necesitan todavía calibración, al menos suponen una cierta ayuda para el proyectista.

Evaluation of the mechanical properties of self compacting concrete using current estimating models. Estimating the modulus of elasticity, tensile strength, and modulus of rupture of self compacting concrete

This study includes an analysis of the applicability of current models used for estimating the mechanical properties of conventional concrete to self-compacting concrete. The mechanical properties evaluated are: modulus of elasticity, tensile strength, and modulus of rupture. An extensive database which included the dosifications and the mechanical properties of 627 mixtures from 138 different references, was used. The models considered are: ACI, EC-2, NZS 3101:2006 (New Zealand code) and the CSA A23.3-04 (Canadian code). The precision in estimating the modulus of elasticity and tensile strength is acceptable for all models; however, all models are less precise in estimating the modulus of rupture.

La crisis económica en las concesiones de autopistas de peaje

A los pocos años de entrar en explotación las concesiones de autopistas de peaje adjudicadas en España a partir de 1996, comenzó la crisis económica. Esos contratos de concesión asignaron la mayoría de los riesgos (expropiación, construcción y tráfico) al sector privado. En este trabajo analizamos el impacto de la crisis económica sobre el sector de autopistas, así como las medidas adoptadas por el Estado para evitar el concurso de las sociedades concesionarias. Las conclusiones obtenidas pueden ayudar a un mejor diseño y desarrollo de los contratos de concesión.

Electrooxidación del amonio en aguas residuales domésticas

La utilización de procesos electroquímicos para el tratamiento de aguas residuales está adquiriendo cada día más importancia por su versatilidad, reducido tamaño y capacidad de automatización. La operación es atractiva desde el punto de vista económico. Además, los tiempos de retención para el tratamiento son pequeños.

Evaluación del comportamiento de la interfase FRP-Hormigón en vigas de hormigón reforzadas con materiales compuestos

En el presente documento se analiza el uso de ensayos beam-test, análogos a los empleados comúnmente para medir la adherencia de barras, en el estudio de la adherencia FRP-Hormigón. Los resultados se trasladan a la comprobación del despegue en la zona entre fisuras de flexión en vigas de hormigón reforzadas con materiales compuestos de propiedades mecánicas similares. Finalmente se presenta una comparación con los modelos más relevantes de la literatura especializada.

Metodología de evaluación de las reglas de operación de embalses en avenidas

El avance de la presión antrópica sobre las márgenes de los cauces, y la creciente dificultad técnica, política y social para ejecutar nuevos proyectos de grandes presas, promueve la necesidad de utilizar más eficientemente los sistemas de control de avenidas existentes. En el presente trabajo se presenta una metodología de análisis para evaluar y comparar las estrategias de gestión de embalses, considerando su operación individual, a fin de establecer la más adecuada. En particular se comparan dos modos de gestión ante situación de avenidas: el Método de Evaluación Volumétrica (MEV) desarrollado por Girón (1988), de amplia difusión en España, y un modelo de optimización de la gestión mediante Programación Lineal Entera Mixta (PLEM). Para ello se ha implementado un entorno de cálculo con estructura modular. El primer módulo permite generar un conjunto representativo de hidrogramas de entrada a los embalses mediante simulación de Monte Carlo. Luego, dos módulos que funcionan en paralelo simulan la gestión del embalse según las dos estrategias mencionadas (MEV y PLEM). Finalmente, se evalúa el comportamiento de ambas estrategias ante el conjunto de solicitaciones hidrológicas generado. Se propone el empleo del Índice de Riesgo Global (I1), que pondera el resultado de la estrategia de gestión frente a un conjunto de hidrogramas de solicitación. Dicho indicador tiene en cuenta el daño esperado debido a los caudales máximos vertidos y el riesgo para la presa debido a los niveles máximos alcanzados en el embalse. Para ello se analiza la función de distribución de probabilidad de las dos variables (máximo caudal vertido y máximo nivel alcanzado) para la población de hidrogramas analizada. El modelo PLEM se calibra empleando el índice I1. Este mismo índice es utilizado para comparar ambas estrategias, entendiendo como la más adecuada aquella que tenga asociado el menor I1. Este sistema de análisis se aplicó a tres embalses de la cuenca del río Segura, con diferentes características en lo referente al tipo y capacidad de aliviadero, volumen de embalse y de resguardo. En los tres casos se han obtenido mejores resultados con el modelo PLEM que con el modelo MEV, tanto en lo concerniente a caudales máximos vertidos como a los niveles máximos alcanzados, para todo el rango de avenidas analizado. Sin embargo, la diferencia entre ambas estrategias no es muy significativa y el MEV presenta características que lo hacen más adecuado para su empleo en tiempo real

Strength and stiffness of repaired tendons

Rotator cuff tears of the shoulder are a common cause of pain and disability. Although surgery is frequently beneficial, re-tearing of the tendons is likely to re-occur. In many cases even if the reparation is successful it will still generate discomfort, problems with mobility, as well as a sharp pain. This project is funded in the cooperation with the Hospital Clinico San Carlos de Madrid. The purpose of this work is to analyze the effect of the surgical repair and the application of different therapies, including mesenchymal stem cell therapy on the biomechanical properties (strength and stiffness) of the repaired tendon. An animal model of rotator cuff tendon reparations has been developed on laboratory rats.To obtain the mechanical response of the healthy and repaired tendons, it was necessary to develop an experimental set up to reproduce the in-vivo working conditions of the tendons (37 ºC, immersed in physiological serum), and especially the load transfer. The biomechanical properties (maximum load and stiffness) have been measured in healthy and repaired tendons. A total of 70 rats are used in this particular study. It has been found that the repaired tendon is stronger than the original on. However, the repaired tendons demonstrate less flexibility than the healthy (original) ones prior to the damage

Usos médicos de la seda

Las excelentes propiedades de este biomaterial se conocen desde antaño. Se están desarrollando ahora nuevas aplicaciones en la reparación de tejidos y en farmacología

Mechanical behaviour and rupture of normal and pathological human ascending aortic wall

The mechanical properties of aortic wall, both healthy and pathological, are needed in order to develop and improve diagnostic and interventional criteria, and for the development of mechanical models to assess arterial integrity. This study focuses on the mechanical behaviour and rupture conditions of the human ascending aorta and its relationship with age and pathologies. Fresh ascending aortic specimens harvested from 23 healthy donors, 12 patients with bicuspid aortic valve (BAV) and 14 with aneurysm were tensile-tested in vitro under physiological conditions. Tensile strength, stretch at failure and elbow stress were measured. The obtained results showed that age causes a major reduction in the mechanical parameters of healthy ascending aortic tissue, and that no significant differences are found between the mechanical strength of aneurysmal or BAV aortic specimens and the corresponding age-matched control group. The physiological level of the stress in the circumferential direction was also computed to assess the physiological operation range of healthy and diseased ascending aortas. The mean physiological wall stress acting on pathologic aortas was found to be far from rupture, with factors of safety (defined as the ratio of tensile strength to the mean wall stress) larger than six. In contrast, the physiological operation of pathologic vessels lays in the stiff part of the response curve, losing part of its function of damping the pressure waves from the heart.

An alternative methodology to predict aging effects on the mechanical properties of glass fiber reinforced cement (GRC)

The effect of three different aging methods (immersion in hot water, freeze–thaw cycles and wet–dry cycles) on the mechanical properties of GRC were studied and compared. Test results showed that immersion in hot water may be an unreliable method for modified GRC formulations, with it being in probability a very harmful procedure. A new aging method, mixing freeze–thaw cycles and wet–dry cycles, seems to be the most accurate simulation of weather conditions that produce a noticeable change in GRC mechanical properties. Future work should be carried out to find a correlation between real weather and the proposed aging method.

Correlation Between Processing Conditions, Microstructure and Mechanical Behavior in Regenerated Silkworm Silk Fibers

Regenerated silkworm fibers spun through a wet-spinning process followed by an immersion postspinning drawing step show a work to fracture comparable with that of natural silkworm silk fibers in a wide range of spinning conditions. The mechanical behavior and microstructure of these high performance fibers have been characterized, and compared with those fibers produced through conventional spinning conditions. The comparison reveals that both sets of fibers share a common semicrystalline microstructure, but significant differences are apparent in the amorphous region. Besides, high performance fibers show a ground state and the possibility of tuning their tensile behavior. These properties are characteristic of spider silk and not of natural silkworm silk, despite both regenerated and natural silkworm silk share a common composition different from that of spider silk.

Synchrotron strain scanning for residual stress measurement in cold-drawn steel rods

Cold-drawn steel rods and wires retain significant residual stresses as a consequence of the manufacturing process. These residual stresses are known to be detrimental for the mechanical properties of the wires and their durability in aggressive environments. Steel makers are aware of the problem and have developed post-drawing processes to try and reduce the residual stresses on the wires. The present authors have studied this problem for a number of years and have performed a detailed characterization of the residual stress state inside cold-drawn rods, including both experimental and numerical techniques. High-energy synchrotron sources have been particularly useful for this research. The results have shown how residual stresses evolve as a consequence of cold-drawing and how they change with subsequent post-drawing treatments. The authors have been able to measure for the first time a complete residual strain profile along the diameter in both phases (ferrite and cementite) of a cold-drawn steel rod.

Influence of coiling on the stress relaxation of prestressing steel wires

The possible deleterious effects of coiling and long-term storage of coiled wires on the stress relaxation behaviour of prestressing steel wires has been checked by means of experimental work and a simple analytical model. The results show that if the requirements of standards are fulfilled (minimum coiling diameters), these effects can be neglected. However, some other factors, such as previous residual stresses, long-term storage or storage at high temperatures, can trigger or emphasize this damage to the material. In the authors' opinion, checking the final curvature of the wires after uncoiling prior to prestressing, as required in some standards, is to be recommended.