Composition dependency of the glass forming ability (GFA) in Mg—Ni—Si system by mechanical alloying

The pure elemental powder mixtures with the compositions of Mg₆₅Ni_xSi₃₅−_x (x = 10, 20, 25, 33 at.%) were subject to high-energy ball mill, and the structures of the mixtures at different intervals of milling were characterised by X-ray diffraction (XRD). The compositional dependency of the glass forming ability (GFA) in Mg–Ni–Si system was evaluated based on the experimental results and the theoretical calculation. The compositional dependency of GFA in Mg–Ni–Si system can be understood well by comparing the enthalpies of the crystalline and amorphous phases based on the Miedema's theory for the formation enthalpy of alloys. Increasing the Ni/Mg ratio and/or decreasing Si content can improve the amorphous formability. The calculation results might be of great help in optimising the composition with high GFA in Mg–Ni–Si system.

11B nuclear magnetic resonance study of boron nitride nanotubes prepared by mechano-thermal method

We reported ¹¹B nuclear magnetic resonance studies of boron nitride (BN) nanotubes prepared by mechano-thermal route. The NMR lineshape obtained at 192.493 MHz (14.7 T) was fitted with two Gaussian functions, and the ¹¹B nuclear magnetization relaxations were satisfied with the stretched–exponential function, exp[-(tlT₁)^(D+1)/6] (D: space dimension) at all temperatures. In addition, the temperature dependence of spin–lattice relaxation rates was well described by T_i^-1 = aT (a: constant, T: temperature) and could be understood in terms of direct phonon process. All the 11BNMR results were explained by considering the inhomogeneous distribution of the paramagnetic metal catalysts, such as α-Fe, Fe–N, and Fe₂ B, that were incorporated during the process of high-energy ball milling of boron powder and be synthesized during subsequent thermal annealing. X-ray powder diffraction as well as electron paramagnetic resonance (EPR) on BN nanotubes were also conducted and the results obtained supported these conclusions.

Mice lacking angiotensin-converting enzyme have increased energy expenditure, with reduced fat mass and improved glucose clearance

In addition to its role in the storage of fat, adipose tissue acts as an endocrine organ, and it contains a functional renin-angiotensin system (RAS). Angiotensin-converting enzyme (ACE) plays a key role in the RAS by converting angiotensin I to the bioactive peptide angiotensin II (Ang II). In the present study, the effect of targeting the RAS in body energy homeostasis and glucose tolerance was determined in homozygous mice in which the gene for ACE had been deleted (ACE^-/-) and compared with wild-type littermates. Compared with wild-type littermates, ACE^-/- mice had lower body weight and a lower proportion of body fat, especially in the abdomen. ACE^-/- mice had greater fed-state total energy expenditure (TEE) and resting energy expenditure (REE) than wild-type littermates. There were pronounced increases in gene expression of enzymes related to lipolysis and fatty acid oxidation (lipoprotein lipase, carnitine palmitoyl transferase, long-chain acetyl CoA dehydrogenase) in the liver of ACE^-/- mice and also lower plasma leptin. In contrast, no differences were detected in daily food intake, activity, fed-state plasma lipids, or proportion of fat excrete in fecal matter. In conclusion, the reduction in ACE activity is associated with a decreased accumulation of body fat, especially in abdominal fat depots. The decreased body fat in ACE^-/- mice is independent of food intake and appears to be due to a high energy expenditure related to increased metabolism of fatty acids in the liver, with the additional effect of increased glucose tolerance.

The 'caffeine-sweetness' effect; potential reduction of energy in caffeinated sugar-sweetened soft drinks

Background – Excessive consumption of sugar sweetened beverages (SSB) is a contributing factor in the occurrence of overweight and obesity. The high energy intake, low satiation, high glycemic index, and intense marketing are all thought to contribute to their over consumption. In addition, the role of the mildly-addictive chemical caffeine in SSB has been questioned (Griffiths and Vernotica, 2000, Keast and Riddell, 2007). We have previously shown that low concentrations of caffeine may decrease sweetness of sugars and thereby result in excess energy in SSB formulations (Ebbeling et al., 2006).
Objective – Without noticeably affecting flavour, to determine potential energy reduction when decreasing sucrose concentration from caffeinated and de-caffeinated SSB.
Design – Human psychophysical taste evaluations in water, sucrose and model SSB. Triangle forced-choice ascending method of limits was used to determine caffeine taste threshold in water and sucrose (n= 62). Directional paired comparison tests to determine 1/ the influence of caffeine on sweetness of sucrose (n= 23), and 2/ the nonperceivable difference when decreasing the sucrose and caffeine concentrations in a model SSB (n= 30).
Outcomes – Caffeine, at sub-threshold concentrations in common SSB (0.67mM) can be perceived in sucrose solutions because it significantly inhibits sweetness (p<0.001), the ‘caffeine sweetness effect’. Presumably coremoval of caffeine and sucrose could be achieved without affecting the sweetness of the SSB. Removing caffeine from the model SSB allowed an energy reduction of 137.4 KJ per 500 ml serving (12.6% sucrose reduction) without noticeably affecting flavour for 80% of the population. The energy reduction possible without co-removal of caffeine was a more modest 32 KJ per 500 ml serving (3.5% sucrose reduction).
Conclusion – Sub-threshold concentrations of caffeine suppress sweetness resulting in higher concentrations of sugars in SSB. Excessive consumption of SSB is linked to the obesity epidemic, and we suggest the removal of caffeine and subsequent removal of 137.4 KJ energy will have long term public health benefits.

Tailoring the photocatalytic activity of nanoparticulate zinc oxide by transition metal oxide doping

The successful use of nanoparticulate ZnO in applications such as UV-screening agents or photocatalyst for the destruction of chemical waste requires the development of techniques for controlling its photocatalytic activity. In this study, we have investigated transition metal doping as a means of achieving this goal. Powders of ZnO, Mn_xZn_1−xO, and Co_xZn_1−xO were synthesised by a three-stage process consisting of high-energy mechanical milling, heat treatment, and washing. The photocatalytic activity of these powders was evaluated using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that the photocatalytic activity of Co_xZn_1−xO progressively decreased with the doping level. In contrast, the activity of Mn_xZn_1−xO initially increased with doping up to a level of 2 mol% and thereafter declined. These results demonstrate that doping with transition metal oxides can be used to tailor the photocatalytic properties of nanoparticulate ZnO.

Effect of nanocrystalline structure on the corrosion of a Fe20Cr alloy

The corrosion behaviour of nanocrystalline and microcrystalline Fe20Cr alloys, prepared by high energy ball milling followed by compaction and sintering, was studied in 0.05M H2SO4 and 0.05M H2SO4 + 0.5M NaCl by potentiodynamic polarization. The nanocrystalline alloy exhibited improved passivating ability and pitting resistance as described by passivation potential, critical current density, passive current density and breakdown potential. XPS and SIMS analysis revealed greater Cr content in the passive film formed on the nanocrystalline form of the alloy. The enhanced passivating ability of the nanocrystalline alloy was attributed to the formation of the passive film with higher Cr content.

Processing and excellent oxidation resistance of nanocrystalline Fe-Cr alloys

Nanocrystalline and microcrystalline Fe-10Cr alloys were prepared by high energy ball milling followed by compaction and sintering, and then oxidized in air for 52 hours at 400ºC. The oxidation resistance of nanocrystalline Fe-10Cr alloy as determined by measuring the weight gain after regular time intervals was compared with that of the microcrystalline alloy of same chemical composition (also prepared by the same processing route and oxidized under identical conditions). Oxidation resistance of nanocrystalline Fe10Cr alloy was found to be in excess of an order of magnitude superior than that of microcrystalline Fe10Cr alloy. The paper also presents results of secondary ion mass spectrometry of oxidized samples of nanocrystalline and microcrystalline Fe-Cr alloys, evidencing the formation of a more protective oxide scale in the nanocrystalline alloy.

Acceleration data reveal the energy management strategy of a marine ectotherm during reproduction

1. Maintaining a high and stable body temperature is often critical for female ectotherms during reproduction. Yet this strategy may be energetically costly, and therefore challenging, during this period of already high-energy demand. 2. Here, the 6-week deployment of tri-axial accelerometers (n = 6) on a marine ectotherm, the loggerhead turtle (Caretta caretta), reproducing at the northern limit of the species’ breeding range (i.e. in a thermally dynamic environment) revealed the behavioural mechanisms underlying its energy management strategy during the breeding season. 3. The estimated activity levels of female loggerheads using overall dynamic body acceleration (ODBA) were high during the breeding season, suggesting that marine turtles may not be able to remain inactive for long periods in the same manner as terrestrial ectotherms, because of the thermally dynamic nature of their environment. 4. However, activity levels were not constant throughout the season, being impacted by both ambient water temperature and female reproductive status. In cold water at the beginning of the nesting season, high levels of activity suggested that females behaviourally thermoregulated by seeking out warm water patches along the shoreline. Interactions with male turtles (courtship and/or avoidance) may also explain this high level of activity. As sea temperatures warmed up and the amount of energy devoted to reproduction probably increased, the turtles spent more time resting during long sequential flat-bottomed dives, and reduced any unnecessary locomotory activity. 5. Turtles may therefore adjust their activity patterns in response to seasonal variations in abiotic (i.e. ambient temperature) and biotic (i.e. reproductive status) factors. This may help minimize activity-linked metabolic rate and maximize reproductive output over a season while breeding in thermally dynamic environments. 6. A mechanistic model gave support to these empirical results. The model revealed that actively maintaining high and stable body temperature is of clear benefit to female turtles at temperate breeding sites. While energetically costly, such active thermoregulatory behaviour may speed up egg maturation, allowing turtles to initiate nesting earlier in the season, and hence maximize reproductive output.

Excellent electrochemical performance of LiFe0.4Mn0.6PO4 microspheres produced using a double carbon coating process

Composite LiFe0.4Mn0.6PO4/C microspheres are considered advanced cathode materials for electric vehicles and other high-energy density applications due to their advantages of high energy density and excellent cycling stability. LiFe0.4Mn0.6PO4/C microspheres have been produced using a double carbon coating process employing traditional industrial techniques (ball milling, spray-drying and annealing). The obtained LiFe0.4Mn0.6PO4 microspheres exhibit a high discharge capacity of around 166 mA h g-1 at 0.1 C and excellent rate capabilities of 132, 103, and 72 mA h g-1 at 5, 10, and 20 C, respectively. A reversible capacity of about 152 mA h g-1 after 500 cycles at a current density of 1 C indicates an outstanding cycling stability. The excellent electrochemical performance is attributed to the micrometer-sized spheres of double carbon-coated LiFe0.4Mn0.6PO4 nanoparticles with improved electric conductivity and higher Li ion diffusion coefficients, ensuring full redox reactions of all nanoparticles. The results show that the advanced high-energy density cathode materials can be produced using existing industry techniques.

Effect of sintering temperature on electrochemical performance of LiFe0·4Mn0·6PO4/C cathode materials

Carbon coated LiFe0·4Mn0·6PO4 (LiFe0·4Mn0·6PO4/C) was synthesised using high energy ball milling and annealing processes. The starting materials of Li2C2O4, FeC2O4.2H2O, MnC2O4.2H2O, NH4H2PO4 were firstly milled for 40 h, and followed by further milling for 5 h after adding glucose solution. The milled sample was heated at different temperatures (550, 600, 650 and 700°C) for 10 h to produce LiFe0·4Mn0·6PO4/C composites. The structure and morphology of the samples were investigated using X-ray diffraction, field emission scanning electron microscopy, and high resolution electron microscopy. The phase of samples annealed at 550 and 600°C mainly consists of olivine type LiFePO4, but a small amount of Fe2P impurity phase is formed in the samples annealed at 650 and 700°C. Electrochemical analysis results show that LiFe0·4Mn0·6PO4/C synthesised at 600°C exhibits the best performance with the initial discharge capacity of 128 mAh g-1 at 0·1 C, and 109 mAh g-1 at 1 C after 500 cycles. The LiFe0·4Mn0·6PO4/C exhibits excellent electrochemical properties for high energy density lithium ion batteries.

Novel Na+ Ion diffusion mechanism in mixed organic-inorganic ionic liquid electrolyte leading to high Na+ transference number and stable, high rate electrochemical cycling of sodium cells

Ambient temperature sodium batteries hold the promise of a new generation of high energy density, low-cost energy storage technologies. Particularly challenging in sodium electrochemistry is achieving high stability at high charge/discharge rates. We report here mixtures of inorganic/organic cation fluorosulfonamide (FSI) ionic liquids that exhibit unexpectedly high Na+ transference numbers due to a structural diffusion mechanism not previously observed in this type of electrolyte. The electrolyte can therefore support high current density cycling of sodium. We investigate the effect of NaFSI salt concentration in methylpropylpyrrolidinium (C3mpyr) FSI ionic liquid (IL) on the reversible plating and dissolution of sodium metal, both on a copper electrode and in a symmetric Na/Na metal cell. NaFSI is highly soluble in the IL allowing the preparation of mixtures that contain very high Na contents, greater than 3.2 mol/kg (50 mol %) at room temperature. Despite the fact that overall ion diffusivity decreases substantially with increasing alkali salt concentration, we have found that these high Na+ content electrolytes can support higher current densities (1 mA/cm2) and greater stability upon continued cycling. EIS measurements indicate that the interfacial impedance is decreased in the high concentration systems, which provides for a particularly low-resistance solid-electrolyte interphase (SEI), resulting in faster charge transfer at the interface. Na+ transference numbers determined by the Bruce-Vincent method increased substantially with increasing NaFSI content, approaching >0.3 at the saturation concentration limit which may explain the improved performance. NMR spectroscopy, PFG diffusion measurements, and molecular dynamics simulations reveal a changeover to a facile structural diffusion mechanism for sodium ion transport at high concentrations in these electrolytes.

High performance green buildings

This work aims to study and analyze strategies and measures to improve energy performance in residential and service buildings, in order to minimize energy losses and energy consumption. Due to the high energy dependence of European Union (EU), including Portugal and Slovenia, and high percentage of energy consumption in the building sector, there was a need to adopt strategies at European level with ambitious goals. This came to force EU - Member States to take measures to achieve the proposed targets for energy consumption reduction. To this end, EU - Member States have adapted the laws to their needs and formed specialized agencies and qualified experts on energy certification, which somehow evaluate buildings according to their performance. In this study, the external characteristics of the building in order to meet its thermal needs and from there to survey the existing and possible constructive solutions to be used at the envelope will be examined, in order to increase comfort and reduce the need of use technical means of air conditioning. The possibility of passive heating and ventilation systems also will be discussed. These techniques are developed in parallel with the deployment and design of the building. In this manner, to reduce the energy consumption, various techniques and technologies exploit natural resources. Thus, appear the more sustainable and efficient buildings, so-called Green Buildings have been appeared. The study ends with the identification of measures used in several buildings, proving the economic return in the medium to long term, as well as the satisfaction of their users.

Estudo da sinterização de cavacos de aço ferritico

This research studies the sintering of ferritic steel chips from the machining process. Were sintered metal powder obtained from machining process chips for face milling of a ferritic steel. The chip was produced by machining and characterized by SEM and EDS, and underwent a process of high energy mill powder characterized also by SEM and EDS. Were constructed three types of matrixes for uniaxial compression (relation l / d greater than 2.5). The differences in the design of the matrixes were essentially in the direction of load application, which for cylindrical case axial direction, while for the rectangular arrays, the longer side. Two samples were compressed with different geometries, a cylindrical and rectangular with the same compaction pressure of 700 MPa. The samples were sintered in a vacuum resistive furnace, heating rate 20 °C / min., isotherm 1300 °C for 60 minutes, and cooling rate of 25 °C / min to room temperature. The starting material of the rectangular sample was further annealed up to temperature of 800 ° C for 30 min. Sintered samples were characterized by scanning electron microscopy, optical microscopy and EDS. The sample compressed in the cylindrical matrix did not show a regular density reflecting in the sintered microstructure revealed by the irregular geometry of the pores, characterizing that the sintering was not complete, reaching only the second phase. As for the specimen compacted in the rectangular array, the analysis performed by scanning electron microscopy, optical microscopy and EDS indicate a good densification, and homogeneous microstructure in their full extent. Additionally, the EDS analyzes indicate no significant changes in chemical composition in the process steps. Therefore, it is concluded that recycling of chips, from the processed ferritic steel is feasible by the powder metallurgy. It makes possible rationalize raw material and energy by manufacture of known properties components from chips generated by the machining process, being benefits to the environment

Performance and hormonal profile in broiler chickens fed with different energy levels during post restriction period

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structural characterization and Curie temperature determination of a sodium strontium niobate ferroelectric nanostructured powder

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)