Modelling the activated sludge flocculation process combining laser light diffraction particle sizing and population balance modelling (PBM)

A technique based on laser light diffraction is shown to be successful in collecting on-line experimental data. Time series of floc size distributions (FSD) under different shear rates (G) and calcium additions were collected. The steady state mass mean diameter decreased with increasing shear rate G and increased when calcium additions exceeded 8 mg/l. A so-called population balance model (PBM) was used to describe the experimental data, This kind of model describes both aggregation and breakage through birth and death terms. A discretised PBM was used since analytical solutions of the integro-partial differential equations are non-existing. Despite the complexity of the model, only 2 parameters need to be estimated: the aggregation rate and the breakage rate. The model seems, however, to lack flexibility. Also, the description of the floc size distribution (FSD) in time is not accurate.

Full-scale demonstration of biological nutrient removal in a single tank SBR process

Complete biological nutrient removal (BNR) in a single tank, sequencing batch reactor (SBR) process, is demonstrated here at full-scale on a typical domestic wastewater. The unique feature of the UniFed process is the introduction of the influent into the settled sludge blanket during the settling and decant periods of the SBR operation. This achieves suitable conditions for denitrification and anaerobic phosphate release which is critical to successful biological phosphorus removal, It also achieves a selector effect, which helps in generating a compact, well settling biomass in the reactor. The results of this demonstration show that it is possible to achieve well over 90% removal of GOD, nitrogen and phosphorus in such a process. Effluent quality achieved over a six-month operating period directly after commissioning was: 29 mg/l GOD, 0.5 mg/l NH4-N, 1.5 mg/l NOx-N and 1.5 mg/l PO4-P (50%-iles of daily samples). During an 8-day, intensive sampling period, the effluent BOD5 was

Teaching drawing: an interdisciplinary pedagogical experience in a graphic design course

Various authors have written about the importance of drawing in design methodology. Their general conclusion points drawing as an essential tool for design research, as it allows investigation of several alternative solutions in design process (Cross, 2007). The recent profound changes in design nature (Norman, 2011), justify a discussion on the purpose of drawing in design courses. As a consequence of this new reality, the educational institutions face the challenge of the definition of their curricular structures and teaching methodologies. Among others, concepts such as collaboration and multidisciplinary design approaches have been discussed as strategies for design education (Heller and Talarico, 2011, pp. 82-85). In this context, and using our teaching activity experience in Drawing and Design areas, the authors discuss:  how can drawing methods be included in the current design teaching?  can drawing be considered as an interdisciplinary approach?  what contributions can these methodologies provide to the educational/learning process? Based on these concerns, we developed an interdisciplinary project in the Graphic Design Course with two curricular units: Drawing 1 and Aesthetic and Design Theory 1. In this article the authors present the aims and process developed, and discuss the outcomes of this pedagogical experience.

Exploring the interdisciplinary process in design education

The work presented herein follows an ongoing research that aims to analyze methodological practices to be applied in Design Education. A reflection about methodological strategies in Design Education and the function of drawing in Design represents the beginning of this study. Then, we developed an interdisciplinary pedagogical experience with the Graphic Design 1st grade students from our institution (IPCA). In the current academic year, 2013/2014, we continue to evolve this project, introducing changes in the initial proposal. Major alterations focused on the aspects that could be strengthened in terms of interdisciplinarity. In this article, the authors describe those changes and discuss the outcomes of the novel proposal. As we have already reported, this investigation follows a reflection about working methods to be adopted in Design Education. This is in accordance with other previously published works that purpose the enlargement of Design into new knowledge fields such as Experience or Service Design, changing not only the role of the graphic designer, but also the skills required to be a professional designer (Alain Findelli, 2001), (Brian Lawson, 2006), (Ciampa-Brewer, 2010). Furthermore, concepts such as cooperation or multidisciplinary design, amongst others, have been frequently debated as design teaching strategies (Heller and Talarico, 2011, pp. 82-85). These educational approaches also have an impact on our research. The analysis of all these authors’ contributions together with a reflection on our teaching practice allowed us to propose an improved interdisciplinary intervention.

Prestação de serviços de assessoria e fiscalização da obra de "reabilitação das coberturas, acessibilidades e segurança da antiga escola Veiga Beirão - Palácio Valadares, em Lisboa"

O presente relatório diz respeito a um estágio de natureza profissional realizado com o objectivo de constituir Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil no perfil de Edificações, do Instituto Superior de Engenharia de Lisboa. O estágio subordinado ao tema “Prestação de serviços de Assessoria, Fiscalização e Coordenação de Segurança da Obra de REABILITAÇÃO DAS COBERTURAS, ACESSIBILIDADES E SEGURANÇA DA ANTIGA ESCOLA VEIGA BEIRÃO – PALÁCIO VALADARES, EM LISBOA”, decorreu na Pengest – Planeamento, Engenharia e Gestão, S.A., empresa vocacionada para a prestação de serviços de Assessoria, Gestão, Coordenação e Fiscalização de Obras, sector no qual possui vasta e diversificada experiência, e reconhecidos mérito e competência. O objectivo da empreitada é o de recuperação deste imóvel, intervenção necessária à instalação no local da Exposição “República e Ensino” enquadrada no âmbito das Comemorações do Centenário da República. A empreitada foi adjudicada ao Empreiteiro Teixeira Duarte, S.A, pelo valor de €998.072,76. O prazo é de 4,5 meses prevendo-se a conclusão para 18 de Março de 2010. Embora a proposta de estágio tenha decorrido no início de 2010, no âmbito do tema que viria a ser proposto e de forma a integrar a Estagiária numa empresa em pleno funcionamento, o estágio teve início aquando do início da empreitada, em Novembro de 2009. Exceptuando os trabalhos de montagem da grua-torre e dos andaimes para a cobertura provisória, que decorreram antes da consignação, foi acompanhado todo o processo de Fiscalização. A Estagiária participou na análise do Plano de Trabalhos, nas vistorias às fracções autónomas e edifícios adjacentes, nas visitas à obra e na elaboração de relatórios mensais. Acompanhou os procedimentos da Pengest no Controlo do Planeamento, da Qualidade e Financeiro. Em relação à Coordenação de Segurança em obra, por ser um tema tão vasto e específico, teve acesso aos relatórios, não tendo efectivamente participado nas actividades desenvolvidas sobre esta matéria. Sob a co-orientação da Eng.ª Isabel Vicente, responsável da Fiscalização e orientação do Eng.º José Pedro Fernandes do ISEL, a estagiária desenvolveu este estágio de forma proveitosa, sempre com o auxílio de uma equipa experiente em Gestão e Fiscalização.

Educational characteristics of adult students in portuguese technological schools

Despite a massive expansion of education in Portugal, since the 1970’s, educational attainment of the adult population in the country remains low. The numbers of working-age people in some form of continuing education are among the lowest, according to the OECD and EU-27 statistics. Technological Schools(TS), initially created in the 1990’s, under the umbrella of the Ministry of Economy in partnership with industry and industrial associations, aimed to prepare qualified staff for industries and services in the country, particularly in the engineering sector, through the provision of post secondary non-university programmes of studies, the CET (Technological Specialization Courses). Successful CET students are awarded a DET(Diploma of Technological Specialization), which corresponds to Vocational Qualification level IV of the EU, according to the latest alteration (2005) of the Education Systems Act (introduced in 1986). In this, CET’s are also clearly defined as one of the routes for access to Higher Education (HE), in Portugal. The PRILHE (Promoting Reflective and Independent Learning in Higher Education) multinational project, funded by the European Socrates Grundtvig Programme, aimed to identify the learning processes which enable adult students in higher education to become autonomous reflective learners and search best practices to support these learning processes. During this research, both quantitative and qualitative methods were used to determine how students organise their studies and develop their learning skills. The Portuguese partner in the project’ consortium used a two case studies approach, one with students of Higher Education Institutions and other with students of TS. This paper only applies to students of TS, as these have a predominant bias towards engineering. Results show that student motivation and professional teaching support contribute equally to the development of an autonomous and reflective approach to learning in adult students; this is essential for success in a knowledge economy, where lifelong learning is the key to continuous employment.

Teaching and learning mathematics using moodle

This paper summarizes a project that is contributing to a change in the way of teaching and learning Mathematics. Mathematics is a subject of the Accounting and Administration course. In this subject we teach: Functions and Algebra. The aim is that the student understand the basic concepts and is able to apply them in other issues, when possible, establishing a bridge between the issues that they have studied and their application in Accounting. As from this year, the Accounting course falls under in Bologna Process. The teacher and the student roles have changed. The time for theoretical and practical classes has been reduced, so it was necessary to modify the way of teaching and learning. In the theoretical classes we use systems of multimedia projection to present the concepts, and in the practical classes we solve exercises. We also use the Excel and the mathematical open source software wxMaxima. To supplement our theoretical and practical classes we have developed a project called MatActiva based on the Moodle platform offered by PAOL - Projecto de Apoio Online (Online Support Project). With the creation of this new project we wanted to take advantage already obtained results with the previous experiences, giving to the students opportunities to complement their study in Mathematics. One of the great objectives is to motivate students, encourage them to overcome theirs difficulties through an auto-study giving them more confidence. In the MatActiva project the students have a big collection of information about the way of the subject works, which includes the objectives, the program, recommended bibliography, evaluation method and summaries. It works as material support for the practical and theoretical classes, the slides of the theoretical classes are available, the sheets with exercises for the students to do in the classroom and complementary exercises, as well as the exams of previous years. Students can also do diagnostic tests and evaluation tests online. Our approach is a reflexive one, based on the professional experience of the teachers that explore and incorporate new tools of Moodle with their students and coordinate the project MatActiva.

Peer Instruction method in introductory math courses

Learning is not a spectator’s sport. Students do not learn much by just sitting in class listening their teachers, memorizing pre-packaged assignments and spitting out answers. The teaching-learning process has been a constant target of studies, particularly in Higher Education, in consequence of the annual increase of new students. The concern with maintaining a desired quality level in the training of these students, conjugated with the will to widen the access to all of those who finish Secondary School Education, has triggered a greater intervention from the education specialists, in partnership with the teachers of all Higher Education areas, in the analysis of this problem. Considering the particular case of Engineering, it has been witnessed a rising concern with the active learning strategies and forms of assessment. Research has demonstrated that students learn more if they are actively engaged with the material they are studying. In this presentation we describe, present and discuss the techniques and the results of Peer Instruction method in an introductory Calculus courses of an Engineering Bach

Projecto dum laboratório remoto para automação de processos industriais

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

A remote virtual experiment in mechanical engineering

Conferência: 2nd Experiment at International Conference (Exp at)- Univ Coimbra, Coimbra, Portugal - Sep 18-20, 2013

Economic, environmental and mixed objective functions in non-linear process optimization using simulated annealing and tabu search

Screening of topologies developed by hierarchical heuristic procedures can be carried out by comparing their optimal performance. In this work we will be exploiting mono-objective process optimization using two algorithms, simulated annealing and tabu search, and four different objective functions: two of the net present value type, one of them including environmental costs and two of the global potential impact type. The hydrodealkylation of toluene to produce benzene was used as case study, considering five topologies with different complexities mainly obtained by including or not liquid recycling and heat integration. The performance of the algorithms together with the objective functions was observed, analyzed and discussed from various perspectives: average deviation of results for each algorithm, capacity for producing high purity product, screening of topologies, objective functions robustness in screening of topologies, trade-offs between economic and environmental type objective functions and variability of optimum solutions.

A distributed system for learning programming on-line

Several Web-based on-line judges or on-line programming trainers have been developed in order to allow students to train their programming skills. However, their pedagogical functionalities in the learning of programming have not been clearly defined. EduJudge is a project which aims to integrate the “UVA On-line Judge”, an existing on-line programming trainer with an important number of problems and users, into an effective educational environment consisting of the e-learning platform Moodle and the competitive learning tool QUESTOURnament. The result is the EduJudge system which allows teachers to apply different pedagogical approaches using a proven e-learning platform, makes problems easy to search through an effective search engine, and provides an automated evaluation of the solutions submitted to these problems. The final objective is to provide new learning strategies to motivate students and present programming as an easy and attractive challenge. EduJudge has been tried and tested in three algorithms and programming courses in three different Engineering degrees. The students’ motivation and satisfaction levels were analysed alongside the effects of the EduJudge system on students’ academic outcomes. Results indicate that both students and teachers found that among other multiple benefits the EduJudge system facilitates the learning process. Furthermore, the experi- ment also showed an improvement in students’ academic outcomes. It must be noted that the students’ level of satisfaction did not depend on their computer skills or their gender.

Engineering real-time applications with WorldFIP: tools and analysis

WorldFIP is standardised as European Norm EN 50170 - General Purpose Field Communication System. Field communication systems (fieldbuses) started to be widely used as the communication support for distributed computer-controlled systems (DCCS), and are being used in all sorts of process control and manufacturing applications within different types of industries. There are several advantages in using fieldbuses as a replacement of for the traditional point-to-point links between sensors/actuators and computer-based control systems. Indeed they concern economical ones (cable savings) but, importantly, fieldbuses allow an increased decentralisation and distribution of the processing power over the field. Typically DCCS have real-time requirements that must be fulfilled. By this, we mean that process data must be transferred between network computing nodes within a maximum admissible time span. WorldFIP has very interesting mechanisms to schedule data transfers. It explicit distinguishes to types of traffic: periodic and aperiodic. In this paper we describe how WorldFIP handles these two types of traffic, and more importantly, we provide a comprehensive analysis for guaranteeing the real-time requirements of both types of traffic. A major contribution is made in the analysis of worst-case response time of aperiodic transfer requests.