Impact of electric vehicles on GB electricity demand and associated benefits for system control

This paper investigates the impact that electric vehicle uptake will have on the national electricity demand of Great Britain. Data from the National Travel Survey, and the Coventry and Birmingham Low Emissions Demonstration (CABLED) are used to model an electrical demand profile in a future scenario of significant electric vehicle market penetration. These two methods allow comparison of how conventional cars are currently used, and the resulting electrical demand with simple substitution of energy source, with data showing how electric vehicles are actually being used at present. The report finds that electric vehicles are unlikely to significantly impact electricity demand in GB. The paper also aims to determine whether electric vehicles have the potential to provide ancillary services to the grid operator, and if so, the capacity for such services that would be available. Demand side management, frequency response and Short term Operating Reserve (STOR) are the services considered. The report finds that electric cars are unlikely to provide enough moveable demand peak shedding to be worthwhile. However, it is found that controlling vehicle charging would provide sufficient power control to viably act as frequency response for dispatch by the transmission system operator. This paper concludes that electric vehicles have technical potential to aid management of the transmission network without adding a significant demand burden. © 2013 IEEE.

Local biomass control on the composition and reactivity of particulate organic matter in aquatic environments

Freshwater ecosystems have been recognized as important components of the global carbon cycle, and the flux of organic matter (OM) from freshwater to marine environments can significantly affect estuarine and coastal productivity. The focus of this study was the assessment of carbon dynamics in two aquatic environments, namely the Florida Everglades and small prairie streams in Kansas, with the aim of characterizing the biogeochemistry of OM. In the Everglades, particulate OM (POM) is mostly found as a layer of flocculent material (floc). While floc is believed to be the main energy source driving trophic dynamics in this oligotrophic wetland, not much is known about its biogeochemistry. The objective of this study was to determine the origin/sources of OM in floc using biomarkers and pigment-based chemotaxonomy to assess specific biomass contributions to this material, on a spatial (freshwater marshes vs. mangrove fringe) and seasonal (wet vs. dry) scales. It was found that floc OM is derived from the local vegetation (mainly algal components and macrophyte litter) and its composition is controlled by seasonal drivers of hydrology and local biomass productivity. Photo-reactivity experiments showed that light exposure on floc resulted in photo-dissolution of POC with the generation of significant amounts of both dissolved OM (DOM) and nutrients (N & P), potentially influencing nutrient dynamics in this ecosystem. The bio-reactivity experiments determined as the amount and rate of CO2 evolution during incubation were found to vary on seasonal and spatial scales and were highly influenced by phosphorus limitation. Not much is known on OM dynamics in small headwater streams. The objective of this study was to determine carbon dynamics in sediments from intermittent prairie streams, characterized by different vegetation cover for their watershed (C4 grasses) vs. riparian zone (C3 plants). In this study sedimentary OM was characterized using a biomarker and compound specific carbon stable isotope approach. It was found that the biomarker composition of these sediments is dominated by higher plant inputs from the riparian zone, although inputs from adjacent prairie grasses were also apparent. Conflicting to some extent with the River Continuum Concept, sediments of the upper reaches contained more degraded OM, while the lower reaches were enriched in fresh material deriving from higher plants and plankton sources as a result of hydrological regimes and particle sorting.

Biomarker Assessment of Spatial and Temporal Changes in the Composition of Flocculent Material (Floc) in the Subtropical Wetland of the Florida Coastal Everglades

Flocculent material (floc) is an important energy source in wetlands. In the Florida Everglades, floc is present in both freshwater marshes and coastal environments and plays a key role in food webs and nutrient cycling. However, not much is known about its environmental dynamics, in particular its biological sources and bio-reactivity. We analysed floc samples collected from different environments in the Florida Everglades and applied biomarkers and pigment chemotaxonomy to identify spatial and seasonal differences in organic matter sources. An attempt was made to link floc composition with algal and plant productivity. Spatial differences were observed between freshwater marsh and estuarine floc. Freshwater floc receives organic matter inputs from local periphyton mats, as indicated by microbial biomarkers and chlorophyll-a estimates. At the estuarine sites, the floc is dominated by mangrove as well as diatom inputs from the marine end-member. The hydroperiod (duration and depth of inundation) at the freshwater sites influences floc organic matter preservation, where the floc at the short-hydroperiod site is more oxidised likely due to periodic dry-down conditions. Seasonal differences in floc composition were not consistent and the few that were observed are likely linked to the primary productivity of the dominant biomass (periphyton in the freshwater marshes and mangroves in the estuarine zone). Molecular evidence for hydrological transport of floc material from the freshwater marshes to the coastal fringe was also observed. With the on-going restoration of the Florida Everglades, it is important to gain a better understanding of the biogeochemical dynamics of floc, including its sources, transformations and reactivity.

Estudo de um secador híbrido (solar-elétrico) para desidratação de frutas

The growing need for food is something that worries the world, which has a population that is growing at a geometric progression while their resources grows at an arithmetic progression. To alleviate this problem there are some proposals, including increased food production or reduce waste thereof. Many studies have been conducted in the world in order to reduce food waste that can reach 40% of production, depending on the region. For this purpose techniques are used to retard degradation of foods, including drying. This paper presents a design of a hybrid fruit dryer that uses solar energy and electric energy with automation of the process. To accomplish drying tests were chosen Typical fruits with good acceptability as processed fruits. During the experiments were measured temperature values at different points. Were also measured humidity values, solar radiation and mass. A data acquisition system was built using a Arduino for obtaining temperatures. The data were sent to a program named Secador de Frutas, done in this work, to plot the same. The volume of the drying chamber was 423 liters and despite the unusual size test using mirrors to increase the incidence of direct radiation, showed that the drier is competitive when compared with other solar dryers produced in Hydraulic Machines and Solar Energy Laboratory (LMHES ) UFRN. The drier has been built at a cost of 3 to 5 times smaller than industrial dryers that operate with the same load of fruit. And the energy cost to produce dried fruits was more feasible compared with such dryers that use LPG as an energy source. However, the drying time was longer.

Investigação da rota biohidrometalúrgica com Acidithiobacillus ferrooxidans/thiooxidans para recuperação do cobalto de baterias de íons lítio descartadas

The recycling of metals from secondary sources can be advantageous. Among the metals of interest, we have cobalt, a metal used for various purposes. As regards the secondary sources of cobalt, the lithium-ion batteries can be considered, since they contain cobalt oxide in their composition (LiCoO2). This way, the objective of this work was to use the microorganism strains (Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans) to bioleach the LiCoO2 extracted from discarded lithium ion batteries with emphasis on the recovery of cobalt for synthesis of new materials of interest. The lineage growth occurred in T&K medium and the growth investigation was made by observing the media, by platelet growth and microscope analysis. Then, the inoculum was standardized on 5 x 106 cells mL-1 and used in bioleaching tests. The bioleaching was investigated: the microorganism nature: separate strains and A. ferrooxidans and A. thiooxidans consortium, bioleaching time (0 to 40 days), inoculum proportion (5 to 50% v/v), energy source (iron and sulfur) and residue concentration (1063 to 8500 mg L-1 of cobalt). The cobalt concentration in the media was found by atomic absorption spectrometry and the medium pH was monitored during the bioleaching. The results show that the amount of bioleached cobalt increases with time and the iron concentration. The bioleaching with A. thiooxidans was not influenced by the addition of sulfur. The use of the two lineages together did not improve the bioleaching rates. Among the lineages, the A. thiooxidans presented better results and was able to bioleach cobalt amounts above 50% in most of the experiments. A. thiooxidans presented lower bioleaching rates, with a maximum of 50% after 24 days of experiment. After reprocessing by bioleaching, the cobalt in solution was used for synthesis of new materials: such as LiCoO2 cathode and as adsorbent pesticide double lamellar hydroxide (HDL Co-Al-Cl) by the Pechini and co-precipitation methods. The reprocessed LiCoO2 presented a unique stoichiometric phase relative to the HT-LiCoO2 structure similar to the JCPDS 44-0145, presenting electrochemical activity when tested as a cathode material. The double lamellar hydroxide Co-Al-Cl was tested as pesticide adsorbent, being possible to adsorb around 100% of the pesticide. The bioleaching was efficient in the recovery of cobalt present in lithium-ion batteries and microorganisms presented high tolerance to the residue, being able to bioleach even at higher LiCoO2 concentrations. The cobalt bioleaching medium did not impair the synthesis phases and the obtained materials presented structure and activity similar to the sintered materials from the reagents containing cobalt.

Zinc regeneration in rechargeable zinc-air fuel cells:a review

Zinc-air fuel cells (ZAFCs) present a promising energy source with a competing potential with the lithium-ion battery and even with proton-exchange membrane fuel cells (PEMFCs) for applications in next generation electrified transport and energy storage. The regeneration of zinc is essential for developing the next-generation, i.e., electrochemically rechargeable ZAFCs. This review aims to provide a comprehensive view on both theoretical and industrial platforms already built hitherto, with focus on electrode materials, electrode and electrolyte additives, solution chemistry, zinc deposition reaction mechanisms and kinetics, and electrochemical zinc regeneration systems. The related technological challenges and their possible solutions are described and discussed. A summary of important R&D patents published within the recent 10 years is also presented.

Using Coding to Improve Localization and Backscatter Communication Performance in Low-Power Sensor Networks

Backscatter communication is an emerging wireless technology that recently has gained an increase in attention from both academic and industry circles. The key innovation of the technology is the ability of ultra-low power devices to utilize nearby existing radio signals to communicate. As there is no need to generate their own energetic radio signal, the devices can benefit from a simple design, are very inexpensive and are extremely energy efficient compared with traditional wireless communication. These benefits have made backscatter communication a desirable candidate for distributed wireless sensor network applications with energy constraints.

The backscatter channel presents a unique set of challenges. Unlike a conventional one-way communication (in which the information source is also the energy source), the backscatter channel experiences strong self-interference and spread Doppler clutter that mask the information-bearing (modulated) signal scattered from the device. Both of these sources of interference arise from the scattering of the transmitted signal off of objects, both stationary and moving, in the environment. Additionally, the measurement of the location of the backscatter device is negatively affected by both the clutter and the modulation of the signal return.

This work proposes a channel coding framework for the backscatter channel consisting of a bi-static transmitter/receiver pair and a quasi-cooperative transponder. It proposes to use run-length limited coding to mitigate the background self-interference and spread-Doppler clutter with only a small decrease in communication rate. The proposed method applies to both binary phase-shift keying (BPSK) and quadrature-amplitude modulation (QAM) scheme and provides an increase in rate by up to a factor of two compared with previous methods.

Additionally, this work analyzes the use of frequency modulation and bi-phase waveform coding for the transmitted (interrogating) waveform for high precision range estimation of the transponder location. Compared to previous methods, optimal lower range sidelobes are achieved. Moreover, since both the transmitted (interrogating) waveform coding and transponder communication coding result in instantaneous phase modulation of the signal, cross-interference between localization and communication tasks exists. Phase discriminating algorithm is proposed to make it possible to separate the waveform coding from the communication coding, upon reception, and achieve localization with increased signal energy by up to 3 dB compared with previous reported results.

The joint communication-localization framework also enables a low-complexity receiver design because the same radio is used both for localization and communication.

Simulations comparing the performance of different codes corroborate the theoretical results and offer possible trade-off between information rate and clutter mitigation as well as a trade-off between choice of waveform-channel coding pairs. Experimental results from a brass-board microwave system in an indoor environment are also presented and discussed.

O potencial energético do gradiente térmico na plataforma continental do sul do brasil

O crescimento da demanda energética, prevista para a metade do século XXI, com números embasados no crescimento demográfico e de consumo dos países em desenvol- vimento, sugere a busca por fontes energéticas renováveis e de menor impacto ao meio ambiente, conforme os tratados da política internacional. Portanto, o fornecimento de energia suplementar se torna vital nas sociedades modernas e sua extensão até o mar tem se constituído uma recente preocupação do ponto de vista enérgico e ecológico. Várias formas de conversão de energia foram desenvolvidas no decorrer dos anos, com destaque para a energia dos gradientes térmicos. A Plataforma Continental Sul do Bra- sil (PSCB) possui alta variabilidade espacial e temporal nos campos de temperatura, de forma que existe a necessidade de uma análise das regiões de maior potencial energético com respeito ao gradiente vertical de temperatura. Neste estudo, foram utilizados dados do modelo OCCAM com uma grade de resolu- ção horizontal de 0, 25o e resolução vertical de 66 níveis, distribuídos ao longo de um sistema de coordenadas vertical. Foram utilizadas imagens de temperatura superfícial do mar (TSM) obtidas a partir do sensor AVHRR (Advanced Very High Resolution Ra- diometer) de forma a realizar a validação dos dados do modelo OCCAM. A análise da média dos dados do modelo indicou um sítio energético de maior viabilidade devido oC ao padrão médio do gradiente térmico de aproximadamente 0, 17 ao longo da coluna vertical (545 m de profundidade) no oceano. Neste local, foram coletados os dados, e aplicados a um módulo de conversão de energia térmica dos oceanos que vem sendo desenvolvido na Universidade Federal do Rio Grande - FURG. A região de estudo de- monstrou possuir um local com ótimo potencial energético, onde a produção máxima de energia pode alcançar 111, 9MW , associada com um padrão variabilidade tempo- ral dominante de 12 meses. Este sítio energético demonstra maior eficiência durante o período de verão e outono ao longo dos anos e sua média para todo o período é de 94, 3MW . Neste estudo, duas correntes: Corrente do Brasil (CB) e a Contra Corrente Costeira (CCC), com águas de origem tropical e subantártica com aportes continentais, respecti- vamente, tem alta correlação com os valores dos gradientes térmicos e com os significa- tivos eventos de conversão energética. O sítio energético demonstrou alta estabilidade à sazonalidade e à gama de eventos meteorológicos e oceanográficos, de forma que pode ser qualificado como uma fonte suplementar a matriz energética do país para um futuro próximo.

Simulation of a resonant inverter

Mostly developed since the Industrial Revolution, the automation of systems and equipment around us is responsible for a technological progress and economic growth without precedents, but also by a relentless energy dependence. Currently, fossil fuels still tend to come as the main energy source, even in developed countries, due to the ease in its extraction and the mastery of the technology needed for its use. However, the perception of its ending availability, as well as the environmental impact of this practice has led to a growing energy production originated from renewable sources. Easy maintenance, coupled with the fact that they are virtually inexhaustible, makes the solar and wind energy very promising solutions. In this context, this work proposes to facilitate energy production from these sources. To this end, in this work the power inverter is studied, which is an equipment responsible for converting DC power available by solar or wind power in traditional AC power. Then it is discussed and designed a new architecture which, in addition to achieve a high energy e - ciency, has also the ability to adapt to the type of conversion desired by the user, namely if he wants to sell electricity to the power grid, be independent of it or bet on a self consumption system. In order to achieve the promised energy e ciency, the projected inverter uses a resonant DC-DC converter, whose architecture signi cantly decreases the energy dissipated in the conversion, allowing a higher power density. The adaptability of the equipment is provided by an adaptive control algorithm, responsible for assessing its behavior on every iteration and making the necessary changes to achieve maximum stability throughout the process. To evaluate the functioning of the proposed architecture, a simulation is presented using the PLECS simulation software.

Casca de arroz como adsorvente para extração de micotoxinas em cebola

A produção mundial de arroz chega a 80 milhões de toneladas ao ano, considerando que as cascas representam 20% deste valor, anualmente são geradas cerca de 1.162.000 toneladas desse rejeito. Há alguns anos, esse material era descartado no ambiente, atualmente as leis de proteção ambiental, demandaram na preocupação com resíduos de casca de arroz (FOLETO, 2005). Segundo Mayer (2006) a casca leva aproximadamente 5 anos para se decompor e exala um volume elevado de metano, um dos gases responsáveis pelo efeito estufa. Visando proteger a integridade do meio ambiente, estão sendo buscadas alternativas para reduzir os impactos ambientais do descarte e recuperar os investimentos na cultura do grão. Devido seu alto teor de silício a casca de arroz, é matéria-prima de grande interesse para aplicação em vários ramos: indústria eletrônica, cerâmica e na agricultura e também pode ser utilizada como fonte energética e ser aplicadas como adsorvente, em análises químicas (FOLETO, 2005; ROSA, 2009). Neste trabalho o objetivo foi padronizar método para a determinação das aflatoxinas B1, B2, G1, G2 e ocratoxiana A em cebola, empregando a técnica de extração, Dispersão da Matriz em Fase Sólida (MSPD), tendo a casca de arroz como adsorvente, de forma a possibilitar a determinação dos contaminantes empregando cromatografia de camada delgada de alta eficiência (HPTLC) e/ou cromatografia líquida de alta eficiência acoplada a detector de fluorescência (HPLC-FD). A cebola (Allium cepa L.) foi a matriz escolhida devido sua importância econômica, ela é a terceira hortaliça mais importante economicamente no Brasil, depois do tomate e da batata. O país está entre os dez maiores produtores do mundo, sendo que na safra de 2010 a produção foi de 1.548.146 toneladas. Dentre os estados que se destacam pela sua produção estão: Santa Catarina, São Paulo e Rio Grande do Sul. No entanto, a cebola assim como os demais alimentos é suscetível à contaminação fúngica e se entre a microbiota estiverem espécies toxigênicas pode ocorrer à produção de micotoxinas. O método foi validado avaliando-se curva analítica, linearidade, limites de detecção e quantificação, precisão (repetitividade e precisão intermediária) e exatidão (recuperação) para cada tipo de determinação cromatográfica. Para HPTLC, os limites de detecção variaram entre 0,33-5µg Kg-1 e os de quantificação entre 1-15µg Kg-1 Para o método HPLC-FD os limites de detecção variaram entre 0,003– 0,26 µg Kg-1 e os de quantificação 0,03 – 2,6 µg Kg-1 . As recuperações para o método HPTLC variaram entre 76- 95% e para HPLC-FD variaram entre 72-88%. O método desenvolvido foi aplicado para verificar a ocorrência de micotoxinas em 14 amostras de cebola. A contaminação com aflatoxinas foi verificada em 43% das amostras analisadas. O nível máximo encontrado foi de 90 µg Kg-1 para aflatoxina B2 em uma amostra de cebola crioula, com o defeito de mancha negra.

El desarrollo del sistema energético solar-hidrógeno en América Latina: potencialidades, oportunidades y barreras

El Sistema Energético Solar-Hidrógeno (SESH) constituye un sistema energético cuya fuente primaria es la energía solar, directa o indirecta, y la secundaria el hidrógeno. Actualmente, se considera como la mejor opción para complementar en el mediano y sustituir en el largo plazo, al actual sistema energético basado en fuentes fósiles. En este contexto se desenvuelve este trabajo, cuyo objetivo es identificar y analizar los factores intervinientes en el desarrollo del SESH en el ámbito latinoamericano, mediante una investigación documental basada en una amplia revisión bibliográfica. Se obtiene que la mayoría de países latinoamericanos disponen de ingentes potenciales aprovechables de energías renovables que harían posible y atractiva económicamente la implantación del SESH; que la hidrogenaría y biomasa son las fuentes más adecuadas como base para esta implantación, tanto por su potencial como por su presencia en la matriz energética y costos del SESH. Los estudios indican que la energización rural y el transporte urbano constituyen nichos de oportunidad para la penetración del SESH. También se reportan barreras: acciones de investigación escasas y concentradas en pocos países, un exiguo talento humano formado y capacitado para operar y desarrollar esta tecnología, como resultado de una débil oferta formativa; y la carencia de un marco legal e institucional que incentive el desarrollo de este sistema. Se concluye que sólo con la acción concertada de centros de investigación, universidades y la empresa privada, bajo la tutela del estado, se logrará que este elemento químico singular conduzca el desarrollo humano de la región por caminos sustentables.

Applications of Photoinduced Electron Transfer Chemistry: Photoremovable Protecting Groups and Carbon Dioxide Conversion

Traditional organic chemistry has long been dominated by ground state thermal reactions. The alternative to this is excited state chemistry, which uses light to drive chemical transformations. There is considerable interest in using this clean renewable energy source due to concerns surrounding the combustion byproducts associated with the consumption of fossil fuels. The work presented in this text will focus on the use of light (both ultraviolet and visible) for the following quantitative chemical transformations: (1) the release of compounds containing carboxylic acid and alcohol functional groups and (2) the conversion of carbon dioxide into other useable chemicals. Chapters 1-3 will introduce and explore the use of photoremovable protecting groups (PPGs) for the spatiotemporal control of molecular concentrations. Two new PPGs are discussed, the 2,2,2-tribromoethoxy group for the protection of carboxylic acids and the 9-phenyl-9-tritylone group for the protection of alcohols. Fundamental interest in the factors that affect C–X bond breaking has driven the work presented in this text for the release of carboxylic acid substrates. Product analysis from the UV photolysis of 2,2,2-tribromoethyl-(2′-phenylacetate) in various solvents results in the formation of H–atom abstraction products as well as the release of phenylacetic acid. The deprotection of alcohols is realized through the use of UV or visible light photolysis of 9-phenyl-9-tritylone ethers. Central to this study is the use of photoinduced electron transfer chemistry for the generation of ion diradicals capable of undergoing bond-breaking chemistry leading to the release of the alcohol substrates. Chapters 4 and 5 will explore the use of N-heterocyclic carbenes (NHCs) as a catalyst for the photochemical reduction of carbon dioxide. Previous experiments have demonstrated that NHCs can add to CO2 to form stable zwitterionic species known as N-heterocylic-2-carboxylates (NHC–CO2). Work presented in this text illustrate that the stability of these species is highly dependent on solvent polarity, consistent with a lengthening of the imidazolium to carbon dioxide bond (CNHC–CCO2). Furthermore, these adducts interact with excited state electron donors resulting in the generation of ion diradicals capable of converting carbon dioxide into formic acid.

Information and Development

According to the National Academy of Sciences of the United States was Modern electronics has given rise to a second Industrial Revolution ... its impact on society could be higher even than the original industrial revolution.The information is granted a number of attributes that have made valued as an asset as necessary as the energy source.Repeat with more conviction to as we move into the twenty-first century, that of scientific and technological development depends nations.

Desenvolvimento de metodologia de análise de indicadores de sustentabilidade como ferramenta para tomada de decisão utilizando lógica fuzzy

Dissertação (Mestrado em Tecnologia Nuclear)