激光二极管端面抽运Nd∶YVO4固体激光器热致光束畸变非对称的平衡

由于a轴切割Nd∶YVO4晶体的非对称性,使得激光二极管(LD)端面抽运Nd∶YVO4固体激光器不同于Nd∶YAG激光器,输出的激光经常产生非对称结果。用有限元法分析激光二极管端面抽运a轴切割Nd∶YVO4固体激光器的晶体热效应,包括温度分布、内部应力和产生的形变。分析结果表明端面抽运a轴切割Nd∶YVO4晶体产生了椭球热透镜效应。从结构方面和抽运方面提出了热透镜非对称性的平衡方法,实验验证了方法的可行性。

热容型板条激光器的感应折射率计算

高平均功率固体激光器的增益介质由于受热而容易发生畸变,如常用材料YAG,波前畸变和去偏振现象会同时发生,高热负载固体激光介质的热效应已成为制约激光器输出功率进一步提高的严重障碍。给出一种计算热容型板条激光器热感生折射率的方法。把YAG晶体的四阶压光张量从晶胞坐标系转换到实验室坐标系,采用经过坐标转换后的新的张量,可以分析在YAG激光器中任意应力分布引起的热感应双折射。进一步的计算表明,在zigzag板条激光器中,应力双折射率与板条从晶体毛胚上切割成材的角度有关。同时也对热容板条激光器的热效应和应力特性进行了二维的理论性概述。

Strong visible up-conversion emissions and thermometric applications of Er3+-Yb3+ codoped Al2O3 prepared by the sol-gel method

The Er3+-Yb3+ codoped Al2O3 has been prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)(3)]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)(3) center dot 5H(2)O] and ytterbium nitrate [Yb(NO3)(3) center dot 5H(2)O]. The phase structure, including only two crystalline types of doped Al2O3 phases, theta and gamma, was obtained for the 1 mol% Er3+ and 5 mol% Yb3+ codoped Al2O3 at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300-825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er3+-Yb3+ codoped Al2O3 plays an important role in the application of high temperature sensor.

Analysis on a new type magneto-optical disk for blue lasers

The conventional TbFeCo magneto-optical (MO) medium has a relatively smaller Kerr rotation angle in the blue region than in the red. With the recording wavelength gradually moving to the short wavelength, if TbFeCo is still used as recording medium, the conventional MO disk structure must be optimized to get a larger carrier to noise ratio (CNR). Sabi et al. have found that adding a metal layer attached to the TbFeCo film as thermal control layer is a useful way to get a high CNR. In this paper, we proved this through calculation, and carried out optimization of the new type of disk. Calculation results showed that the new structure is useful in preventing an excessive temperature increase, and has a better thermal response. (c) 2005 Elsevier B.V. All rights reserved.