Mineralogy and stable isotopic composition of carbonates and sulfide minerals from ODP Leg 164 sites

During Ocean Drilling Program Leg 164, gas hydrates were recovered in the Blake Ridge where the top of the gas hydrate zone lies at about 200 meters below seafloor (mbsf) and the bottom-simulating reflector (BSR) is located at about 450 mbsf. There is no sedimentological discontinuity crossing the BSR. The BSR is disrupted by the salt piercement of the Cape Fear Diapir. The authigenic carbonates (dolomite and siderite) are always present in small amounts (a few weight percent) in the sediments; they are also concentrated in millimeter- to centimeter-sized nodules and layers composed of dolomite above the top of the gas hydrate reservoir, and of siderite below the BSR. In the Blake Ridge, the dolomite/siderite boundary is located near 140 mbsf. The distribution with depth of the d18O values of dolomite and siderite shows a sharp decrease from high values (maximum 7.5 per mil) in the topmost 50 m, to very low values (minimum -2.7 per mil) at 140 mbsf, and at greater depth increase to positive values within the range of 1.8 per mil to 5.0 per mil. The d13C distribution is marked by the rapid increase with greater depth from low values (-31.3 per mil to -11.4 per mil) near 50 mbsf to positive values at 110 mbsf, which remain in the range of 1.7 to 5.4 down to 700 mbsf. Diagenetic carbonates were precipitated in pore waters in which d18O and d13C values were highly modified by strong fractionation effects, both in the water and in the CO2-CH4 systems associated with the formation and dissociation of gas hydrates.

Casting a voice for rural struggles during apartheid : the case of AFRA

This paper explores the attempts to co-ordinate rural resistance and struggles in South Africa during apartheid through a case study of the Association for Rural Advancement (AFRA), a land NGO established in Natal in 1979. It was a small group but had a significant local and national impact. The paper addresses three key questions concerning the character and works of AFRA: (1) What was the character and strategy of AFRA in the politicised context of the late 1970s and 1980s? (2) Was there any historical continuity and discontinuity with early attempts by Natal liberals and African landowners to organise anti-removal campaigns in the 1950s? (3) How and to what extent could AFRA negotiate the increasing influence of the Inkatha and KwaZulu government over Natal rural communities? The paper aims to serve as a critical evaluation of AFRA's strategies and activities, and its relationship with rural communities up to 1990 when land movements became nationwide.

Coastal shapes. Geentic clasification 1973 - 2010

An analysis of a stretch of coastline shows multiple alterations through environmental climate actions. The narrow, fragile line displays singularities due to three basic causes. The first is the discontinuity in feed or localised loss of solid coastal material. Called massics, their simplest examples are deltas and undersea canyons. The second is due to a brusque change in the alignment of the shoreline’s edge, headlands, groins, harbour and defence works. Given the name of geometric singularities, their simplest uses are artificial beaches in the shelter of a straight groin or spits. The third is due to littoral dynamics, emerged or submerged obstacles which diffract and refract wave action, causing a change in the sea level’s super-elevation in breaker areas. Called dynamics, the simplest examples are salients, tombolos and shells. Discussion of the causes giving rise to variations in the coastline and formation of singularities is the raison d’être of investigation, using actual cases to check the suitability of the classification proposed, the tangential or differential action of waves on the coastal landscape in addition to possible simple, compound and complex shapes detected in nature, both in erosion and deposit processes

Fisuración y deformaciones en tabiquerías

A diferencia de otros parámetros, el efecto de la existencia de huecos en la aparición y desarrollo de los procesos de fisuración en los paños de fábrica no ha sido considerado por las distintas normativas existentes en la actualidad. En nuestros días se emplea una variada gama de tipologías de elementos de cerramiento para realizar las particiones en las obras de edificación, cada una de ellas con características mecánicas diferentes y distinta metodología de ejecución, siendo de aplicación la misma normativa relativa al cálculo y control de las deformaciones. Tal y como expresamos en el Capitulo 1, en el que se analiza el Estado del Conocimiento, los códigos actuales determinan de forma analítica la flecha probable que se alcanza en los elementos portantes estructurales bajo diferentes condiciones de servicio. Las distintas propuestas que existen respecto para la limitación de la flecha activa, una vez realizado el cálculo de las deformaciones, bien por el método de Branson ó mediante los métodos de integración de curvaturas, no contemplan como parámetro a considerar en la limitación de la flecha activa la existencia y tipología de huecos en un paño de fábrica soportado por la estructura. Sin embargo se intuye y podríamos afirmar que una discontinuidad en cualquier elemento sometido a esfuerzos tiene influencia en el estado tensional del mismo. Si consideramos que, de forma general, los procesos de fisuración se producen al superarse la resistencia a tracción de material constitutivo de la fábrica soportada, es claro que la variación tensional inducida por la existencia de huecos ha de tener cierta influencia en la aparición y desarrollo de los procesos de fisuración en los elementos de partición o de cerramiento de las obras de edificación. En los Capítulos 2 y 3 tras justificar la necesidad de realizar una investigación encaminada a confirmar la relación entre la existencia de huecos en un paño de fábrica y el desarrollo de procesos de fisuración en el mismo, se establece este aspecto como principal Objetivo y se expone la Metodología para su análisis. Hemos definido y justificado en el Capítulo 4 el modelo de cálculo que hemos utilizado para determinar las deformaciones y los procesos de fisuración que se producen en los casos a analizar, en los que se han considerado como variables: los valores de la luz del modelo, el estado de fisuración de los elementos portantes, los efectos de la fluencia y el porcentaje de transmisión de cargas desde el forjado superior al paño de fábrica en estudio. Además se adoptan dos valores de la resistencia a tracción de las fábricas, 0.75MPa y 1.00MPa. La capacidad de representar la fisuración, así como la robustez y fiabilidad ha condicionado y justificado la selección del programa de elementos finitos que se ha utilizado para realizar los cálculos. Aprovechando la posibilidad de reproducir de forma ajustada las características introducidas para cada parámetro, hemos planteado y realizado un análisis paramétricos que considera 360 cálculos iterativos, de cuya exposición es objeto el Capítulo 5, para obtener una serie representativa de resultados sobre los que se realizará el análisis posterior. En el Capítulo 6, de análisis de los resultados, hemos estudiado los valores de deformaciones y estados de fisuración obtenidos para los casos analizados. Hemos determinado la influencia que tiene la presencia de huecos en la aparición de los procesos de fisuración y en las deformaciones que se producen en las diferentes configuraciones estructurales. Las conclusiones que hemos obtenido tras analizar los resultados, incluidas en el Capítulo 7, no dejan lugar a dudas: la presencia, la posición y la tipología de los huecos en los elementos de fábricas soportadas sobre estructuras deformables son factores determinantes respecto de la fisuración y pueden tener influencia en las deformaciones que constituyen la flecha activa del elemento, lo que obliga a plantear una serie de recomendaciones frente al proyecto y frente a la reglamentación técnica. La investigación desarrollada para esta Tesis Doctoral y la metodología aplicada para su desarrollo abre nuevas líneas de estudio, que se esbozan en el Capítulo 8, para el análisis de otros aspectos que no han sido cubiertos por esta investigación a fin de mejorar las limitaciones que deberían establecerse para los Estados Límite de Servicio de Deformaciones correspondientes a las estructuras de edificación. SUMMARY. Unlike other parameters, the effect of the existence of voids in the arising and development of cracking processes in the masonry walls has not been considered by current Codes. Nowadays, a huge variety of enclosure elements types is used to execute partitions in buildings, each one with different mechanical characteristics and different execution methodology, being applied the same rules concerning deflection calculation and control. As indicated in Chapter 1, which analyzes the State of Art, current codes analytically determine the deflection likely to be achieved in structural supporting elements under different service conditions. The different proposals that exist related to live deflection limitation, once performed deformations calculation, either by Branson´s method or considering curvatures integration methods, do not consider in deflection limitation the existence and typology of voids in a masonry wall structured supported. But is sensed and it can be affirmed that a discontinuity in any element under stress influences the stress state of it. If we consider that, in general, cracking processes occur when masonry material tensile strength is exceeded, it is clear that tension variation induced by the existence of voids must have some influence on the emergence and development of cracking processes in enclosure elements of building works. In Chapters 2 and 3, after justifying the need for an investigation to confirm the relationship between the existence of voids in a masonry wall and the development of cracking process in it, is set as the main objective and it is shown the analysis Methodology. We have defined and justified in Chapter 4 the calculation model used to determine the deformation and cracking processes that occur in the cases analyzed, in which were considered as variables: model span values, bearing elements cracking state, creep effects and load transmission percentage from the upper floor to the studied masonry wall. In addition, two masonry tensile strength values 0.75MPa and 1.00MPa have been considered. The cracking consideration ability, robustness and reliability has determined and justified the selection of the finite element program that was used for the calculations. Taking advantage of the ability of accurately consider the characteristics introduced for each parameter, we have performed a parametric analyses that considers 360 iterative calculations, whose results are included in Chapter 5, in order to obtain a representative results set that will be analyzed later. In Chapter 6, results analysis, we studied the obtained values of deformation and cracking configurations for the cases analyzed. We determined the influence of the voids presence in the occurrence of cracking processes and deformations in different structural configurations. The conclusions we have obtained after analyzing the results, included in Chapter 7, leave no doubt: the presence, position and type of holes in masonry elements supported on deformable structures are determinative of cracking and can influence deformations which are the element live deflection, making necessary to raise a number of recommendations related to project and technical regulation. The research undertaken for this Doctoral Thesis and the applied methodology for its development opens up new lines of study, outlined in Chapter 8, for the analysis of other aspects that are not covered by this research, in order to improve the limitations that should be established for Deflections Serviceability Limit States related to building structures.

Updated Co-58 evaluation for background capture reaction (MT102) (JEF/DOC-1367)

The neutron capture (n,gamma) cross-section for 27-Co-58 theoretically presents a single resonance for 9 eV. However, after plotting the processed library, a discontinuity is made clear as the cross section plummets down to cero in a small range of energy where the peak of the resonance would be expected.

Modelos de elementos finitos con aplicación tridimensional de la analogía fluido-fibra, para predecir el comportamiento mecánico de piezas estructurales de madera bajo la presencia de los principales tipos de nudos

Los nudos son los defectos que más disminuyen la resistencia de piezas de madera en la escala estructural, al ocasionar no solo una discontinuidad material, sino también la desviación de las fibras que se encuentran a su alrededor. En la década de los 80 se introdujo la teoría de la analogía fluido-fibra, como un método que aproximaba adecuadamente todas estas desviaciones. Sin embargo en su aplicación tridimensional, nunca se consideraron las diferencias geométricas en el sentido perpendicular al eje longitudinal de las piezas estructurales, lo cual imposibilitaba la simulación numérica de algunos de los principales tipos de nudos, y disminuía la precisión obtenida en aquellos nudos en los que la modelización sí era viable. En este trabajo se propone un modelo programado en lenguaje paramétrico de un software de elementos finitos que, bajo una formulación en tres dimensiones más general, permitirá estudiar de forma automatizada el comportamiento estructural de la madera bajo la influencia de los principales tipos de nudos, a partir de la geometría visible de los mismos y la posición de la médula en la pieza, y el cual ha sido contrastado experimentalmente, simulando de forma muy precisa el comportamiento mecánico de vigas sometidas a ensayos de flexión a cuatro puntos. Knots are the defects that most reduce the strength of lumber at the structural level, by causing not only a material discontinuity but also the deviation of the fibers that surround them. In the 80's it was introduced the theory of the flow-grain analogy as a method to approximating adequately these deviations. However, in three-dimensional applications, geometrical differences in the direction perpendicular to the longitudinal axis of the structural specimens were never considered before, which prevented the numerical simulation of some of the main types of knots, and decreased the achieved precision in those kind of knots where modeling itself was possible. This paper purposes a parametric model programmed in a finite element software, in the way that with a more general three-dimensional formulation, an automated study of the structural behavior of timber under the influence of the main types of knots is allowed by only knowing the visible geometry of such defects, and the position of the pith. Furthermore that has been confirmed experimentally obtaining very accurately simulations of the mechanical behavior of beams under four points bending test.

Steps Ahead in the Few-Group CRoss-Section Library Generation at the Pin Level

There exists an interest in performing pin-by-pin calculations coupled with thermal hydraulics so as to improve the accuracy of nuclear reactor analysis. In the framework of the EU NURISP project, INRNE and UPM have generated an experimental version of a few group diffusion cross sections library with discontinuity factors intended for VVER analysis at the pin level with the COBAYA3 code. The transport code APOLLO2 was used to perform the branching calculations. As a first proof of principle the library was created for fresh fuel and covers almost the full parameter space of steady state and transient conditions. The main objective is to test the calculation schemes and post-processing procedures, including multi-pin branching calculations. Two library options are being studied: one based on linear table interpolation and another one using a functional fitting of the cross sections. The libraries generated with APOLLO2 have been tested with the pin-by-pin diffusion model in COBAYA3 including discontinuity factors; first comparing 2D results against the APOLLO2 reference solutions and afterwards using the libraries to compute a 3D assembly problem coupled with a simplified thermal-hydraulic model.

Edge Detection by Adaptive Splitting II. The Three-Dimensional Case

In Llanas and Lantarón, J. Sci. Comput. 46, 485–518 (2011) we proposed an algorithm (EDAS-d) to approximate the jump discontinuity set of functions defined on subsets of ℝ d . This procedure is based on adaptive splitting of the domain of the function guided by the value of an average integral. The above study was limited to the 1D and 2D versions of the algorithm. In this paper we address the three-dimensional problem. We prove an integral inequality (in the case d=3) which constitutes the basis of EDAS-3. We have performed detailed computational experiments demonstrating effective edge detection in 3D function models with different interface topologies. EDAS-1 and EDAS-2 appealing properties are extensible to the 3D case

Integration of design tools and knowledge capture into a CAD system: a case study

onceptual design phase is partially supported by product lifecycle management/computer-aided design (PLM/CAD) systems causing discontinuity of the design information flow: customer needs — functional requirements — key characteristics — design parameters (DPs) — geometric DPs. Aiming to address this issue, it is proposed a knowledge-based approach is proposed to integrate quality function deployment, failure mode and effects analysis, and axiomatic design into a commercial PLM/CAD system. A case study, main subject of this article, was carried out to validate the proposed process, to evaluate, by a pilot development, how the commercial PLM/CAD modules and application programming interface could support the information flow, and based on the pilot scheme results to propose a full development framework.

Experimental and numerical analysis of reinforced concrete elements subjected to blast loading

El hormigón es uno de los materiales de construcción más empleados en la actualidad debido a sus buenas prestaciones mecánicas, moldeabilidad y economía de obtención, entre otras ventajas. Es bien sabido que tiene una buena resistencia a compresión y una baja resistencia a tracción, por lo que se arma con barras de acero para formar el hormigón armado, material que se ha convertido por méritos propios en la solución constructiva más importante de nuestra época. A pesar de ser un material profusamente utilizado, hay aspectos del comportamiento del hormigón que todavía no son completamente conocidos, como es el caso de su respuesta ante los efectos de una explosión. Este es un campo de especial relevancia, debido a que los eventos, tanto intencionados como accidentales, en los que una estructura se ve sometida a una explosión son, por desgracia, relativamente frecuentes. La solicitación de una estructura ante una explosión se produce por el impacto sobre la misma de la onda de presión generada en la detonación. La aplicación de esta carga sobre la estructura es muy rápida y de muy corta duración. Este tipo de acciones se denominan cargas impulsivas, y pueden ser hasta cuatro órdenes de magnitud más rápidas que las cargas dinámicas impuestas por un terremoto. En consecuencia, no es de extrañar que sus efectos sobre las estructuras y sus materiales sean muy distintos que las que producen las cargas habitualmente consideradas en ingeniería. En la presente tesis doctoral se profundiza en el conocimiento del comportamiento material del hormigón sometido a explosiones. Para ello, es crucial contar con resultados experimentales de estructuras de hormigón sometidas a explosiones. Este tipo de resultados es difícil de encontrar en la literatura científica, ya que estos ensayos han sido tradicionalmente llevados a cabo en el ámbito militar y los resultados obtenidos no son de dominio público. Por otra parte, en las campañas experimentales con explosiones llevadas a cabo por instituciones civiles el elevado coste de acceso a explosivos y a campos de prueba adecuados no permite la realización de ensayos con un elevado número de muestras. Por este motivo, la dispersión experimental no es habitualmente controlada. Sin embargo, en elementos de hormigón armado sometidos a explosiones, la dispersión experimental es muy acusada, en primer lugar, por la propia heterogeneidad del hormigón, y en segundo, por la dificultad inherente a la realización de ensayos con explosiones, por motivos tales como dificultades en las condiciones de contorno, variabilidad del explosivo, o incluso cambios en las condiciones atmosféricas. Para paliar estos inconvenientes, en esta tesis doctoral se ha diseñado un novedoso dispositivo que permite ensayar hasta cuatro losas de hormigón bajo la misma detonación, lo que además de proporcionar un número de muestras estadísticamente representativo, supone un importante ahorro de costes. Con este dispositivo se han ensayado 28 losas de hormigón, tanto armadas como en masa, de dos dosificaciones distintas. Pero además de contar con datos experimentales, también es importante disponer de herramientas de cálculo para el análisis y diseño de estructuras sometidas a explosiones. Aunque existen diversos métodos analíticos, hoy por hoy las técnicas de simulación numérica suponen la alternativa más avanzada y versátil para el cálculo de elementos estructurales sometidos a cargas impulsivas. Sin embargo, para obtener resultados fiables es crucial contar con modelos constitutivos de material que tengan en cuenta los parámetros que gobiernan el comportamiento para el caso de carga en estudio. En este sentido, cabe destacar que la mayoría de los modelos constitutivos desarrollados para el hormigón a altas velocidades de deformación proceden del ámbito balístico, donde dominan las grandes tensiones de compresión en el entorno local de la zona afectada por el impacto. En el caso de los elementos de hormigón sometidos a explosiones, las tensiones de compresión son mucho más moderadas, siendo las tensiones de tracción generalmente las causantes de la rotura del material. En esta tesis doctoral se analiza la validez de algunos de los modelos disponibles, confirmando que los parámetros que gobiernan el fallo de las losas de hormigón armado ante explosiones son la resistencia a tracción y su ablandamiento tras rotura. En base a los resultados anteriores se ha desarrollado un modelo constitutivo para el hormigón ante altas velocidades de deformación, que sólo tiene en cuenta la rotura por tracción. Este modelo parte del de fisura cohesiva embebida con discontinuidad fuerte, desarrollado por Planas y Sancho, que ha demostrado su capacidad en la predicción de la rotura a tracción de elementos de hormigón en masa. El modelo ha sido modificado para su implementación en el programa comercial de integración explícita LS-DYNA, utilizando elementos finitos hexaédricos e incorporando la dependencia de la velocidad de deformación para permitir su utilización en el ámbito dinámico. El modelo es estrictamente local y no requiere de remallado ni conocer previamente la trayectoria de la fisura. Este modelo constitutivo ha sido utilizado para simular dos campañas experimentales, probando la hipótesis de que el fallo de elementos de hormigón ante explosiones está gobernado por el comportamiento a tracción, siendo de especial relevancia el ablandamiento del hormigón. Concrete is nowadays one of the most widely used building materials because of its good mechanical properties, moldability and production economy, among other advantages. As it is known, it has high compressive and low tensile strengths and for this reason it is reinforced with steel bars to form reinforced concrete, a material that has become the most important constructive solution of our time. Despite being such a widely used material, there are some aspects of concrete performance that are not yet fully understood, as it is the case of its response to the effects of an explosion. This is a topic of particular relevance because the events, both intentional and accidental, in which a structure is subjected to an explosion are, unfortunately, relatively common. The loading of a structure due to an explosive event occurs due to the impact of the pressure shock wave generated in the detonation. The application of this load on the structure is very fast and of very short duration. Such actions are called impulsive loads, and can be up to four orders of magnitude faster than the dynamic loads imposed by an earthquake. Consequently, it is not surprising that their effects on structures and materials are very different than those that cause the loads usually considered in engineering. This thesis broadens the knowledge about the material behavior of concrete subjected to explosions. To that end, it is crucial to have experimental results of concrete structures subjected to explosions. These types of results are difficult to find in the scientific literature, as these tests have traditionally been carried out by armies of different countries and the results obtained are classified. Moreover, in experimental campaigns with explosives conducted by civil institutions the high cost of accessing explosives and the lack of proper test fields does not allow for the testing of a large number of samples. For this reason, the experimental scatter is usually not controlled. However, in reinforced concrete elements subjected to explosions the experimental dispersion is very pronounced. First, due to the heterogeneity of concrete, and secondly, because of the difficulty inherent to testing with explosions, for reasons such as difficulties in the boundary conditions, variability of the explosive, or even atmospheric changes. To overcome these drawbacks, in this thesis we have designed a novel device that allows for testing up to four concrete slabs under the same detonation, which apart from providing a statistically representative number of samples, represents a significant saving in costs. A number of 28 slabs were tested using this device. The slabs were both reinforced and plain concrete, and two different concrete mixes were used. Besides having experimental data, it is also important to have computational tools for the analysis and design of structures subjected to explosions. Despite the existence of several analytical methods, numerical simulation techniques nowadays represent the most advanced and versatile alternative for the assessment of structural elements subjected to impulsive loading. However, to obtain reliable results it is crucial to have material constitutive models that take into account the parameters that govern the behavior for the load case under study. In this regard it is noteworthy that most of the developed constitutive models for concrete at high strain rates arise from the ballistic field, dominated by large compressive stresses in the local environment of the area affected by the impact. In the case of concrete elements subjected to an explosion, the compressive stresses are much more moderate, while tensile stresses usually cause material failure. This thesis discusses the validity of some of the available models, confirming that the parameters governing the failure of reinforced concrete slabs subjected to blast are the tensile strength and softening behaviour after failure. Based on these results we have developed a constitutive model for concrete at high strain rates, which only takes into account the ultimate tensile strength. This model is based on the embedded Cohesive Crack Model with Strong Discontinuity Approach developed by Planas and Sancho, which has proved its ability in predicting the tensile fracture of plain concrete elements. The model has been modified for its implementation in the commercial explicit integration program LS-DYNA, using hexahedral finite elements and incorporating the dependence of the strain rate, to allow for its use in dynamic domain. The model is strictly local and does not require remeshing nor prior knowledge of the crack path. This constitutive model has been used to simulate two experimental campaigns, confirming the hypothesis that the failure of concrete elements subjected to explosions is governed by their tensile response, being of particular relevance the softening behavior of concrete.

A three-dimensional self-adaptive hp finite element method for the characterization of waveguide discontinuities

We propose the use of a highly-accurate three-dimensional (3D) fully automatic hp-adaptive finite element method (FEM) for the characterization of rectangular waveguide discontinuities. These discontinuities are either the unavoidable result of mechanical/electrical transitions or deliberately introduced in order to perform certain electrical functions in modern communication systems. The proposed numerical method combines the geometrical flexibility of finite elements with an accuracy that is often superior to that provided by semi-analytical methods. It supports anisotropic refinements on irregular meshes with hanging nodes, and isoparametric elements. It makes use of hexahedral elements compatible with high-order H(curl)H(curl) discretizations. The 3D hp-adaptive FEM is applied for the first time to solve a wide range of 3D waveguide discontinuity problems of microwave communication systems in which exponential convergence of the error is observed.

Benchmarking of COBAYA3 pin-by-pin for VVER

This paper presents results of the benchmarking of COBAYA3 pin-by-pin for VVER-1000 obtained in the frame of the EU NURISP project. The 3D lattice solver in COBAYA3 uses transport corrected multi-group diffusion approximation with side-dependent interface discontinuity factors of GET or Selengut Black Box type. The objective of this study is to test the few-group calculation scheme when using structur ed and unstructured spatial meshes. Unstructured mesh is necessary to model the water gaps between the hexagonal assemblies. The benchmark problems include pin-by-pin calculations of 2D subsets of the core and comparison with APOLLO2 and TR IPOLI4 transport reference solutions. COBAYA3 solutions in 2, 4 and 8 energy groups have been tested. The results show excellent agreement with the reference on es when using side-dependent interface discontinuity factors.

Proyectando entre ruinas : lógicas de intervención continua en la arquitectura contemporánea

Los cambios percibidos hacia finales del siglo XX y a principios del nuevo milenio, nos ha mostrado que la crisis cultural de la que somos participes refleja también una crisis de los modelos universales. Nuestra situación contemporánea, parece indicar que ya no es posible formular un sistema estético para atribuirle una vigencia universal e intemporal más allá de su estricta eficacia puntual. La referencia organizada, delimitada, invariable y específica que ofrecía cualquier emplazamiento, en tanto preexistencia, reflejaba una jerarquía del sistema formal basado en lo extensivo: la medida, las normas, el movimiento, el tiempo, la modulación, los códigos y las reglas. Sin embargo, actualmente, algunos aspectos que permanecían latentes sobre lo construido, emergen bajo connotaciones intensivas, transgrediendo la simple manifestación visual y expresiva, para centrase en las propiedades del comportamiento de la materia y la energía como determinantes de un proceso de adaptación en el entorno. A lo largo del todo el siglo XX, el desarrollo de la relación del proyecto sobre lo construido ha sido abordado, casi en exclusiva, entre acciones de preservación o intervención. Ambas perspectivas, manifestaban esfuerzos por articular un pensamiento que diera una consistencia teórica, como soporte para la producción de la acción aditiva. No obstante, en las últimas décadas de finales de siglo, la teoría arquitectónica terminó por incluir pensamientos de otros campos que parecen contaminar la visión sesgada que nos refería lo construido. Todo este entramado conceptual previo, aglomeraba valiosos intentos por dar contenido a una teoría que pudiese ser entendida desde una sola posición argumental. Es así, que en 1979 Ignasi Solá-Morales integró todas las imprecisiones que referían una actuación sobre una arquitectura existente, bajo el termino de “intervención”, el cual fue argumentado en dos sentidos: El primero referido a cualquier tipo de actuación que se puede hacer en un edificio, desde la defensa, preservación, conservación, reutilización, y demás acciones. Se trata de un ámbito donde permanece latente el sentido de intensidad, como factor común de entendimiento de una misma acción. En segundo lugar, más restringido, la idea de intervención se erige como el acto crítico a las ideas anteriores. Ambos representan en definitiva, formas de interpretación de un nuevo discurso. “Una intervención, es tanto como intentar que el edificio vuelva a decir algo o lo diga en una determinada dirección”. A mediados de 1985, motivado por la corriente de revisión historiográfica y la preocupación del deterioro de los centros históricos que recorría toda Europa, Solá-Morales se propone reflexionar sobre “la relación” entre una intervención de nueva arquitectura y la arquitectura previamente existente. Relación condicionada estrictamente bajo consideraciones lingüísticas, a su entender, en sintonía con toda la producción arquitectónica de todo el siglo XX. Del Contraste a la Analogía, resumirá las transformaciones en la concepción discursiva de la intervención arquitectónica, como un fenómeno cambiante en función de los valores culturales, pero a su vez, mostrando una clara tendencia dialógica entres dos categorías formales: El Contraste, enfatizando las posibilidades de la novedad y la diferencia; y por otro lado la emergente Analogía, como una nueva sensibilidad de interpretación del edificio antiguo, donde la semejanza y la diversidad se manifiestan simultáneamente. El aporte reflexivo de los escritos de Solá-Morales podría ser definitivo, si en las últimas décadas antes del fin de siglo, no se hubiesen percibido ciertos cambios sobre la continuidad de la expresión lingüística que fomentaba la arquitectura, hacia una especie de hipertrofia figurativa. Entre muchos argumentos: La disolución de la consistencia compositiva y el estilo unitario, la incorporación volumétrica del proyecto como dispositivo reactivo, y el cambio de visión desde lo retrospectivo hacia lo prospectivo que sugiere la nueva conservación. En este contexto de desintegración, el proyecto, en tanto incorporación o añadido sobre un edificio construido, deja de ser considerado como un apéndice volumétrico subordinado por la reglas compositivas y formales de lo antiguo, para ser considerado como un organismo de orden reactivo, que produce en el soporte existente una alteración en su conformación estructural y sistémica. La extensión, antes espacial, se considera ahora una extensión sensorial y morfológica con la implementación de la tecnología y la hiper-información, pero a su vez, marcados por una fuerte tendencia de optimización energética en su rol operativo, ante el surgimiento del factor ecológico en la producción contemporánea. En una sociedad, como la nuestra, que se está modernizando intensamente, es difícil compartir una adecuada sintonía con las formas del pasado. Desde 1790, fecha de la primera convención francesa para la conservación de monumentos, la escala de lo que se pretende preservar es cada vez más ambiciosa, tanto es así, que al día de hoy el repertorio de lo que se conserva incluye prácticamente todas las tipologías del entorno construido. Para Koolhaas, el intervalo entre el objeto y el momento en el cual se decide su conservación se ha reducido, desde dos milenios en 1882 a unas décadas hoy en día. En breve este lapso desaparecerá, demostrando un cambio radical desde lo retrospectivo hacia lo prospectivo, es decir, que dentro de poco habrá que decidir que es lo que se conserva antes de construir. Solá-Morales, en su momento, distinguió la relación entre lo nuevo y lo antiguo, entre el contraste y la analogía. Hoy casi tres décadas después, el objetivo consiste en evaluar si el modelo de intervención arquitectónica sobre lo construido se ha mantenido desde entonces o si han aparecido nuevas formas de posicionamiento del proyecto sobre lo construido. Nuestro trabajo pretende demostrar el cambio de enfoque proyectual con la preexistencia y que éste tiene estrecha relación con la incorporación de nuevos conceptos, técnicas, herramientas y necesidades que imprimen el contexto cultural, producido por el cambio de siglo. Esta suposición nos orienta a establecer un paralelismo arquitectónico entre los modos de relación en que se manifiesta lo nuevo, entre una posición comúnmente asumida (Tópica), genérica y ortodoxa, fundamentada en lo visual y expresivo de las últimas décadas del siglo XX, y una realidad emergente (Heterotópica), extraordinaria y heterodoxa que estimula lo inmaterial y que parece emerger con creciente intensidad en el siglo XXI. Si a lo largo de todo el siglo XX, el proyecto de intervención arquitectónico, se debatía entre la continuidad y discontinuidad de las categorías formales marcadas por la expresión del edificio preexistente, la nueva intervención contemporánea, como dispositivo reactivo en el paisaje y en el territorio, demanda una absoluta continuidad, ya no visual, expresiva, ni funcional, sino una continuidad fisiológica de adaptación y cambio con la propia dinámica del territorio, bajo nuevas reglas de juego y desplegando planes y estrategias operativas (proyectivas) desde su propia lógica y contingencia. El objeto de esta investigación es determinar los nuevos modos de continuidad y las posibles lógicas de producción que se manifiestan dentro de la Intervención Arquitectónica, intentando superar lo aparente de su relación física y visual, como resultado de la incorporación del factor operativo desplegado por el nuevo dispositivo contemporáneo. Creemos que es acertado mantener la senda connotativa que marca la denominación intervención arquitectónica, por aglutinar conceptos y acercamientos teóricos previos que han ido evolucionando en el tiempo. Si bien el término adolece de mayor alcance operativo desde su formulación, una cualidad que infieren nuestras lógicas contemporáneas, podría ser la reformulación y consolidación de un concepto de intervención más idóneo con nuestros tiempos, anteponiendo un procedimiento lógico desde su propia necesidad y contingencia. Finalmente, nuestro planteamiento inicial aspira a constituir un nueva forma de reflexión que nos permita comprender las complejas implicaciones que infiere la nueva arquitectura sobre la preexistencia, motivada por las incorporación de factores externos al simple juicio formal y expresivo preponderante a finales del siglo XX. Del mismo modo, nuestro camino propuesto, como alternativa, permite proyectar posibles sendas de prospección, al considerar lo preexistente como un ámbito que abarca la totalidad del territorio con dinámicas emergentes de cambio, y con ellas, sus lógicas de intervención.Abstract The perceived changes towards the end of the XXth century and at the beginning of the new milennium have shown us that the cultural crisis in which we participate also reflects a crisis of the universal models. The difference between our contemporary situation and the typical situations of modern orthodoxy and post-modernistic fragmentation, seems to indicate that it is no longer possible to formulate a valid esthetic system, to assign a universal and eternal validity to it beyond its strictly punctual effectiveness; which is even subject to questioning because of the continuous transformations that take place in time and in the sensibility of the subject itself every time it takes over the place. The organised reference that any location offered, limited, invariable and specific, while pre-existing, reflected a hierarchy of the formal system based on the applicable: measure, standards, movement, time, modulation, codes and rules. Authors like Marshall Mc Luhan, Paul Virilio, or Marc Augé anticipated a reality where the conventional system already did not seem to respond to the new architectural requests in which information, speed, disappearance and the virtual had blurred the traditional limits of place; pre-existence did no longer possess a specific delimitation and, on the contrary, they expect to reach a global scale. Currently, some aspects that stayed latent relating to the constructed, surface from intensive connotations, transgressing the simple visual and expressive manifestation in order to focus on the traits of the behaviour of material and energy as determinants of a process of adaptation to the surroundings. Throughout the entire Century, the development of the relation of the project relating to the constructed has been addressed, almost exclusively, in preservational or interventianal actions. Both perspectives showed efforts in order to express a thought that would give a theoretical consistency as a base for the production of the additive action. Nevertheless, the last decades of the Century, architectural theory ended up including thoughts from other fields that seem to contaminate the biased vision 15 which the constructed related us. Ecology, planning, philosophy, global economy, etc, suggest new approaches to the construction of the contemporary city; but this time with a determined idea of change and continuous transformation, that enriches the panorama of thought and architectural practice, at the same time, according to some, it puts disciplinary specification at risk, given that there is no architecture without destruction, the constructed organism requires mutation in order to adjust to the change of shape. All of this previous conceptual framework gathered valuable intents to give importance to a theory that could be understood solely from an argumental position. Thusly, in 1979 Ignasi Solá-Morales integrated all of the imprecisions that referred to an action in existing architecture under the term of “Intervention”, which was explained in two ways: The first referring to any type of intervention that can be carried out in a building, regarding protection, conservation, reuse, etc. It is about a scope where the meaning of intensity stays latent as a common factor of the understanding of a single action. Secondly, more limitedly, the idea of intervention is established as the critical act to the other previous ideas such as restauration, conservation, reuse, etc. Both ultimately represent ways of interpretation of a new speech. “An intervention, is as much as trying to make the building say something again or that it be said in a certain direction”. Mid 1985, motivated by the current of historiographical revision and the concerns regarding the deterioration of historical centres that traversed Europe, Solá-Morales decides to reflect on “the relationship” between an intervention of the new architecture and the previously existing architecture. A relationship determined strictly by linguistic considerations, to his understanding, in harmony with all of the architectural production of the XXth century. From Contrast to Analogy would summarise transformations in the discursive perception of architectural intervention, as a changing phenomenon depending on cultural values, but at the same time, showing a clear dialogical tendency between two formal categories: Contrast, emphasising the possibilities of novelty and difference; and on the other hand the emerging Analogy, as a new awareness of interpretation of the ancient building, where the similarity and diversity are manifested simultaneously. For Solá-Morales the analogical procedure is not based on the visible simultaneity of formal orders, but on associations that the subject establishes throughout time. Through analogy it is tried to overcome the simple visual relationship with the antique, to focus on its spacial, physical and geographical nature. If the analogical attempt guides an opening towards a new continuity; it still persists in the connection of dimensional, typological and figurative factors, subordinate to the formal hierarchy of the preexisting subjects. 16 The reflexive contribution of Solá-Morales’ works could be final, if in the last decades before the end of the century there had not been certain changes regarding linguistic expression, encouraged by architecture, towards a kind of figurative hypertrophy, amongst many arguments we are in this case interested in three moments: The dissolution of the compositional consistency and the united style, the volumetric incorporation of the project as a reactive mechanism, and the change of the vision from retrospective towards prospective that the new conservation suggests. The recurrence to the history of architecture and its recognisable forms, as a way of perpetuating memory and establishing a reference, dissolved any instinct of compositive unity and style, provoking permanent relationships to tend to disappear. The composition and coherence lead to suppose a type of discontinuity of isolated objects in which only possible relationships could appear; no longer as an order of certain formal and compositive rules, but as a special way of setting elements in a specific work. The new globalised field required new forms of consistency between the project and the pre-existent subject, motivated amongst others by the higher pace of market evolution, increase of consumer tax and the level of information and competence between different locations; aspects which finally made stylistic consistence inefficient. In this context of disintegration, the project, in incorporation as well as added to a constructed building, stops being considered as a volumetric appendix subordinate to compositive and formal rules of old, to be considered as an organism of reactive order, that causes a change in the structural and systematic configuration of the existing foundation. The extension, previsouly spatial, is now considered a sensorial and morphological extension, with the implementation of technology and hyper-information, but at the same time, marked by a strong tendency of energetic optimization in its operational role, facing the emergence of the ecological factor in contemporary production. The technological world turns into a new nature, a nature that should be analysed from ecological terms; in other words, as an event of transition in the continuous redistribution of energy. In this area, effectiveness is not only determined by the capacity of adaptation to changing conditions, but also by its transforming capacity “expressly” in order to change an environment. In a society, like ours, that is modernising intensively, it is difficult to share an adecuate agreement with the forms of the past. From 1790, the date of the first French convention for the conservation of monuments, the scale of what is expexted to be preserved is more and more ambitious, so much so that nowadays the repertoire of that what is conserved includes practically all typologies of the constructed surroundings. For Koolhaas, the ínterval between the object and the moment when its conservation is decided has been reduced, from two 17 milennia in 1882 to a few decades nowadays. Shortly this lapse will disappear, showing a radical change of retrospective towards prospective, that is to say, that soon it will be necessary to decide what to conserve before constructing. The shapes of cities are the result of the continuous incorporation of architecture, and perhaps that only through architecture the response to the universe can be understood, the continuity of what has already been constructed. Our work is understood also within that system, modifying the field of action and leaving the road ready for the next movement of those that will follow after us. Continuity does not mean conservatism, continuity means being conscient of the transitory value of our answers to specific needs, accepting the change that we have received. That what has been constructed to remain and last, should cause future interventions to be integrated in it. It is necessary to accept continuity as a rule. Solá-Morales, in his time, distinguished between the relationship with new and old, between contrast and analogy. Today, almost three decades later, the objective consists of evaluating whether the model of architectural intervention in the constructed has been maintained since then or if new ways of positioning the project regarding the constructed have appeared. Our work claims to show the change of the approach of projects with pre-existing subjects and that this has got a close relation to the incorporation of new concepts, techniques, tools and necessities that impress the cultural context, caused by the change of centuries. This assumption guides us to establish a parallelism between the forms of connection where that what is new is manifested between a commonly assumed (topical), generic and orthodox position, based on that what is visual and expressive in the last decades of the XXth century, and an emerging (heterotopical), extraordinary and heterodox reality that stimulates the immaterial and that seems to emerge with growing intensity in the XXIst century. If throughout the XXth century the project of architectural intervention was considered from the continuity and discontinuity of formal categories, marked by the expression of the pre-existing building, the new contemporary intervention, as a reactive device in the landscape and territory, demands an absolute continuity. No longer a visual, expressive or functional one but a morphological continuity of adaptation and change with its own territorial dynamics, under new game rules and unfolding new operative (projective) strategies from its own logic and contingency. 18 The aim of this research is to determine new forms of continuity and the possible logic of production that are expressed in the Architectural Intervention, trying to overcome the obviousness of its physical and visual relationship, at the beginning of this new century, as a result of the incorporation of the operative factor that the new architectural device unfolds. We think it is correct to maintain the connotative path that marks the name architectural intervention by bringing previous concepts and theorical approaches that have been evolving through time together. If the name suffers from a wider operational range because of its formulation, a quality that our contemporary logic provokes, the reformulation and consolidation of an interventional concept could be more suitable for our times, giving preference to a logical method from its own necessity and contingency. It seems that now time shapes the topics, it is no longer about materialising a certain time but about expressing the changes that its new temporality generates. Finally, our initial approach aspires to form a new way of reflection that permits us to understand the complex implications that the new architecture submits the pre-existing subject to, motivated by the incorporation of factors external to simple formal and expressive judgement, prevailing at the end of the XXth century. In the same way, our set road, as an alternative, permits the contemplation of possible research paths, considering that what is pre-existing as an area that spans the whole territory with emerging changing dynamics and, with them, their interventional logics.

Agaete revisited: new data on the Gran Canaria tsunamiites.

The tsunami deposits of the valley of Agaete (Pérez-Torrado et al., 2006), north-western Gran Canaria, attributed to the Guimar flank collapse in Tenerife, have been revisited and new data are presented here. Besides the occurrences reported by Pérez-Torrado et al. (2006) a new outcrop was found and named “La Ruina” (at 28º 05’ 47,41” N; 15º 41’ 52,04” W; 71 m asl). The above-mentioned authors suggested the possibility that more than one marine conglomerate deposit could be present in the outcrops of “Llanos de Turmán” and “Berrazales”. At “La Gasolinera” and “La Aldea 1” the conglomerates are formed by a single layer representing one depositional event; at “La Aldea 2”, the conglomerates are composed of two layers directly contacting with each other, but evidence of a time hiatus between them was not found. Although the hypothesis of stacking of two depositional units within the same episode versus deposition of two distinct layers in different time-moments is debatable at the present state of knowledge, the first possibility is favoured. The field evidence at “Llanos de Turman” and “Berrazales” unquestionably shows that terrestrial sediments (colluvia; paleosols) are present and separate two marine conglomerate deposits, indicating that at least two distinct tsunami inundations are needed to explain the stratigraphy. However, at the new “La Ruina” outcrop, besides the two deposits mentioned above, a third and older marine conglomerate was found, clearly separated in time from the ones cited above. The existence of marine conglomerates emplaced in different moments is evidenced by the occurrence of intercalated paleosols, colluvia and other subaerial materials, implying significant time intervals between the emplacement of marine conglomeratic layers. A number of gastropod operculae from the tsunamiites were sent for U-Th dating to try to further constrain the age span of these deposits. The field evidence presented above shows that the emplacement of the deposits is related to, at least, three tsunami events. The lateral correlation between different outcrops is difficult due to variable number of deposits in each outcrop, lateral discontinuity and variability, and to compositional and textural similarity between distinct tsunami sediments. The occurrence of three Pleistocene tsunami deposits in the same area points to a relatively high frequency of tsunamis (generated by landslides, surface rupturing earthquakes, fast entry of voluminous volcanic deposits into the sea or large submarine eruptions). It is possible that this recurrence of tsunami inundations may reflect multiple-phased landslides responsible for the mega-landslide scars prominent in the geomorphology of the neighbouring island of Tenerife. This is a contribution from project “Estabilidad de los edificios volcánicos en Canarias: análisis de los factores geológicos, geomecánicos y paleoclimáticos. Aplicación a los flancos N y S de la isla de Tenerife” financed by MCT, Spain.

Self-similar motion of laser half-space plasmas. II. Thermal waves and intermediate regimes

The one-dimensional self-similar motion of an initially cold, half-space plasma of electron density n,produced by the (anomalous) absorption of a laser pulse of irradiation

discontinuity develops, separating a thermal wave (where convection is negligible) moving into the undisturbed plasma, from a much thinner isothermal flow expanding into the vacuum. For l€~4'3, a qualitative discussion of how plasma behavior changes with a, is given.