Low metal loading catalysts used for the selective hydrogenation of styrene

A series of Group VIII metal catalysts was obtained for the semi-hydrogenation of styrene. Catalysts were characterized by Hydrogen Chemisorption, TPR and XPS. Palladium, rhodium and platinum low metal loading prepared catalysts presented high activity and selectivity (ca. 98%) during the semi-hydrogenation of styrene, being palladium the most active catalyst. The ruthenium catalyst also presented high selectivity (ca. 98%), but the lowest activity. For the palladium catalyst, the influence of the precursor salt and of the reduction temperature on the activity and selectivity were studied. The following activity series was obtained: PdN-423 > PdCl-673 > PdCl-373> PtCl-673 > RhCl-673 >> RuCl-673. As determined by XPS, differences in activity could be attributed, at least in part, to electronic effects.

Ternary surface complex: coadsorption of Cu(II), Zn(II), Cd(II) and nitrilotris(methylenephosphonic) acid onto boehmite

This work studies the effect of NTMP (nitrilotris(methylenephosphonic acid)) on the adsorption of Cu(II), Zn(II), and Cd(II) onto boehmite in the pH range 5-9.5. The data were analyzed using the 2-pK constant capacitance model (CCM) assuming ternary surface complex formation. Under stoichiometric conditions, NTMP is more effective for removing Cu(II) than Zn(II) from solution and the contribution of ternary surface complexes are important to model the adsorption of both metals. Under nonstoichiometric conditions and high surface loading with a Me(II)/NTMP ratio of 1:5, Cu(II) and Zn(II) adsorption is significantly suppressed. In the case of Cd(II) the free metal adsorption is the most dominant species.

Enzyme loading dependence of cellulose hydrolysis of sugarcane bagasse

The enzymatic hydrolysis of steam-pretreated sugarcane bagasse, either delignified or non-delignified, was studied as a function of enzyme loading. Hydrolysis experiments were carried out using five enzyme loadings (2.5 to 20 FPU/g cellulose) and the concentration of solids was 2% for both materials. Alkaline delignification improved cellulose hydrolysis by increasing surface area. For both materials, glucose concentrations increased with enzyme loading. On the other hand, enzyme loadings higher than 15 FPU/g did not result in any increase in the initial rate, since the excess of enzyme adsorbed onto the substrate restricted the diffusion process through the structure.

METHANE DRY REFORMING OVER Ni SUPPORTED ON PINE SAWDUST ACTIVATED CARBON: EFFECTS OF SUPPORT SURFACE PROPERTIES AND METAL LOADING

The influence of metal loading and support surface functional groups (SFG) on methane dry reforming (MDR) over Ni catalysts supported on pine-sawdust derived activated carbon were studied. Using pine sawdust as the catalyst support precursor, the smallest variety and lowest concentration of SFG led to best Ni dispersion and highest catalytic activity, which increased with Ni loading up to 3 Ni atoms nm-2. At higher Ni loading, the formation of large metal aggregates was observed, consistent with a lower "apparen" surface area and a decrease in catalytic activity. The H2/CO ratio rose with increasing reaction temperature, indicating that increasingly important side reactions were taking place in addition to MDR.

Amplitude térmica para germinação de conídios de Drechslera tritici-repentis

A mancha-amarela do trigo, causada pelo fungo Drechslera tritici-repentis, é de ocorrência mundial e uma das principais doenças da cultura. No Brasil, a mesma está presente em todas as safras e pode reduzir o rendimento de grãos em mais de 40%. A sua ampla adaptabilidade a ambientes diversos pode estar relacionada à capacidade dos esporos germinarem sob diferentes temperaturas, assunto que foi examinado neste experimento conduzido na UPF, em 2011. Suspensões de conídios (350 µL) foram depositadas em placas de Petri com meio ágar-água e incubadas em câmara tipo BOD, na presença e ausência de luz, a -5, 0, 5, 10, 15, 20, 25, 30, 35 e 40ºC, por 2, 4, 6, 8 e 10 horas. O trabalho foi conduzido duas vezes, em delineamento inteiramente casualizado, com quatro repetições. Os conídios germinaram tanto na presença como na ausência de luz. A germinação foi nula a -5ºC ou 40ºC. A mesma foi detectada após 2h e aumentou com o tempo de incubação. Através de polinômios de segundo grau estimou-se a máxima germinação a 19ºC e 9,5h de incubação. Houve predominância da germinação bipolar (frequência de 45,0%), seguida da intercalar (33,5%) e da unipolar (21,5%). Os resultados obtidos indicam grande amplitude térmica para germinação dos conídios de D. tritici-repentis, o que explica, parcialmente, sua ampla distribuição geográfica.

Auger-type granular fertylizer distributor: matemathical model and dynamic simulation

The objective of this study was to model mathematically and to simulate the dynamic behavior of an auger-type fertilizer applicator (AFA) in order to use the variable-rate application (VRA) and reduce the coefficient of variation (CV) of the application, proposing an angular speed controller θ' for the motor drive shaft. The input model was θ' and the response was the fertilizer mass flow, due to the construction, density of fertilizer, fill factor and the end position of the auger. The model was used to simulate a control system in open loop, with an electric drive for AFA using an armature voltage (V A) controller. By introducing a sinusoidal excitation signal in V A with amplitude and delay phase optimized and varying θ' during an operation cycle, it is obtained a reduction of 29.8% in the CV (constant V A) to 11.4%. The development of the mathematical model was a first step towards the introduction of electric drive systems and closed loop control for the implementation of AFA with low CV in VRA.

Swine effluent treatment using anaerobic digestion at different loading rates

The industrial swine production is characterized by generation of significant effluent amounts that require treatment. The most adopted practices by Brazilian swine farmers have been wastewater storage in lagoons and its subsequent use as a biofertilizer. Nutrient accumulation in soil and water creates the need for an effective management of these residues. The anaerobic digestion process is an important alternative and low-cost treatment for organic matter reduction. However, its efficiency is limited by the digester capacity of solid degradation, especially at low hydraulic retention times. Thus, the present study aimed to verify the behavior of an upflow anaerobic digester by increasing the organic loading rate. This was accomplished in three stages using, as a parameter, volatile solids at 0.5; 1.0 and 1.5 kgVS m-3 d-1, respectively. This digester model proved to be quite robust and effective in swine manure treatment, achieving high efficiency of volatile solid removal at all stages of the study (stage 1: 61.38%; stage 2: 55.18%; and stage 3: 43.18%). Biogas production was directly related to the increasing organic load, reaching 0.14, 0.85, and 0.86 Nm³ kgVS-1add., respectively, with no significant difference (p<0.05) of biogas methane concentration among the studied stages (73.7, 75.0, and 77.9%).

Mechanical damage during harvest and loading affect orange postharvest quality

Brazil is the world’s largest orange producer; however, part of this production is lost during postharvest. This loss can be minimized by controlling incidence of physical damage throughout the harvest and loading operations. Impacts can negatively modify quantitative and qualitative fruits aspects. The main goal of this study was to measure the impact magnitude in two types of harvest (manual and detachment) and during all steps from picking into bags until loading for transport to the processing industry and additionally evaluating, in laboratory, the physico-chemical quality of the fruit subjected to various impacts, similar to those found in the field. In order to evaluate the impact magnitude, an instrumented sphere was used (760 mm, Techmark, Inc, USA). The following physico-chemical parameters were evaluated during 6-days of storage: weight loss, soluble solids contents, titratable acidity, ascorbic acid content, pH, firmness and peel color. The greatest impacts were observed during harvest, during the detachment practice, and when loading and unloading from bulk storage, with average acceleration values between 249.5 and 531.52G. The impact incidence in oranges were responsible for reducing the soluble solids, titratable acidity, ascorbic acid and weight by to 5.5%; 8.7%; 4.6% and 0.5%, respectively, compared to the control. Impacts during harvest and the various pre-industry manipulation steps must be controlled as they interfere in postharvest quality and physiology of ‘Valência’ oranges.

Sähköavusteisen polkupyörän vääntömomenttisäädön toteuttaminen amplitudimodulaatiolla

Sähköavusteinen polkupyörä on hieman tavallista polkupyörää vahvarakenteisempi ja painavampi. Lisäpainoa tuovat muun muassa akut ja sähkömoottori, joka avustaa polke-mista. Moottori asennetaan yleensä eturenkaan keskiöön. Suurimmassa osassa, jollei kaikissa, kaupallisista sähköavusteisissa polkupyörissä moottori on hiiliharjaton tasavirta-moottori. Hiiliharjattoman tasavirtamoottorin pyörimisnopeutta ja vääntömomenttia voidaan säätää usealla eri tavalla. Markkinoilla olevat säätimet perustuvat poikkeuksetta pulssinleveys-modulaatioon. Tämän työn tarkoituksena on tutkia, onko säätöjärjestelmä mahdollista to-teuttaa muulla tavalla kuin pulssinleveysmodulaattorilla. Tutkimuksessa päädytään käyt-tämään amplitudimodulointia, jolloin taajuus voidaan pitää vakiona. Tämän tutkimuksen rinnalla samaan polkupyörään rakennetaan polkemisenergian avulla akkuja lataava la-tausjärjestelmä. Tämän kandityön puitteissa tutkimus jää kesken, mutta toiminta osoitetaan teoreettisesti ja simuloimalla. Suurin syy kokeellisen testauksen epäonnistumiseen on käytettyjen kom-ponenttien sopimattomuus sovellukseen.

Modelling of mechanical properties of CRFC composites under flexure loading

Carbon Fibre Reinforced Carbon (CFRC) Composites are increasing their applications due to their high strength and Young’s Modulus at high temperatures in inert atmosphere. Although much work has been done on processing and structure and properties relationship, few studies have addressed the modelling of mechanical properties. This work is divided in two parts. In the first part, a modelling of mechanical properties was carried out for two bi-directional composites using a model based on the Bernoulli-Euler theory for symmetric laminated beams. In the second part, acoustic emission (AE) was used as an auxiliary technique for monitoring the failure process of the composites. Differences in fracture behaviour are reflected in patterns of AE.

Instability of a square sheet under symmetric biaxial loading

An early experiment found that a square rubber sheet under symmetric biaxial loading may not remain square. This curious result has been one of the most instructive examples in finite elasticity. Here thermodynamic considerations are used to analyze this instability.

Coberturas do solo sobre a amplitude térmica e a produtividade de pimentão

Com o objetivo de avaliar o efeito dos sistemas de plantio direto e convencional e estratégias de manejo de plantas daninhas na variação da temperatura do solo e na produtividade de pimentão, realizou-se, na Universidade Federal do Semiárido, em Mossoró-RN, um experimento no esquema de parcelas subdivididas, distribuídas no delineamento experimental em blocos casualizados com quatro repetições. Os sistemas de plantio direto e convencional do pimentão foram avaliados nas parcelas; nas subparcelas, avaliaram-se três estratégias de manejo de plantas daninhas (cobertura do solo com filme de polietileno preto, com capinas e sem capinas). Em cada subparcela foram instalados sensores tipo termopares, a 5 cm de profundidade, para medir a temperatura do solo. A partir dos dados obtidos, determinou-se a variação da temperatura ao longo do dia, no período de 20 a 30 dias após o plantio das mudas de pimentão, e a cada cinco dias, a média das temperaturas máxima e mínima e a amplitude térmica diária. Aos 60 e 147 dias após o transplante das mudas de pimentão, foram feitas avaliações da densidade e massa seca de plantas daninhas nos tratamentos sem capinas. Os tratamentos com filme de polietileno e capinado no sistema de plantio convencional apresentaram elevação na temperatura máxima diária do solo em 6,7 e 5,0 ºC, respectivamente, em relação ao sistema de plantio direto com capinas. A amplitude térmica no sistema de plantio convencional nos tratamentos com capinas regulares e com filme de polietileno foi de 11 ºC, ao passo que no sistema de plantio direto a amplitude foi de 6,3, 4,5 e 4,0 ºC nos tratamentos com capinas, sem capinas e com filme de polietileno, respectivamente. A interferência das plantas daninhas nos tratamentos sem capinas resultou em redução de 94,95 e 92,10% da produtividade comercial nos sistemas de plantio direto e convencional, respectivamente.

Kestomagneettitahtikoneen vääntömomentin tuottokyvyn optimointi hybridibussikäyttöön

Työssä tarkastellaan hybridi- ja sähköajoneuvojen voimankäyttöjärjestelmiä ja bussin ajomoottorina toimivan kestomagneettitahtikoneen toimintaa ja sen soveltuvuutta ajoneuvokäyttöön. Esitetään analyyttinen työkalu kestomagneettitahtikoneen induktanssisuunnittelun ja koneen vääntömomentin tuottokyvyn optimoinnin tueksi. Työkalua hyödynnetään esitettävässä ajomoottorin mitoituslaskelmassa. Työssä päätellään, että kestomagneettitahtimoottori soveltuu hyvin ajoneuvokäyttöön. Maksimaalisen vääntömomentin saavuttamiseksi sen roottorin rakenne ja induktanssit on optimoitava. Analysoimalla ajoneuvokäyttöön tarkoitettua kestomagneettitahtimoottoria työkalun avulla havaitaan, että yhtä suuremmalla induktanssisuhteella vääntömomentti on pienempi kentänheikennyksessä kuin ajettaessa konetta taajuusmuuttajalla vakioteholla nimelliskuormalla. Vastaavasti yhtä pienemmillä induktanssisuhteilla vääntömomentti on pienempi kentänheikennyksessä. Todetaan, että vääntömomentti kasvaa induktanssisuhteen poiketessa yhdestä. Suuri vääntömomentti saadaan pienillä induktanssisuhteilla. Induktanssisuhteen kasvattaminen yhdestä ei lisää moottorin tuottamaa vääntömomenttia yhtä paljon kuin induktanssisuhteen pienentäminen. Työn lopuksi verrataan työkalun laskemia tuloksia kirjallisuudesta löytyvillä yhtälöillä laskettuihin tuloksiin. Työkalun laskemat tulokset vaikuttavat ristiriidattomilta ja yhteneväisiltä teorian kanssa. Työkalun toteutuksessa tehdyt teoreettiset yksinkertaistukset aiheuttavat todennäköisesti epätarkkuutta tuloksissa erityisesti suurella kuormituksella.

Electrophysiological measurements of spectral sensitivities: a review

Spectral sensitivities of visual systems are specified as the reciprocals of the intensities of light (quantum fluxes) needed at each wavelength to elicit the same criterion amplitude of responses. This review primarily considers the methods that have been developed for electrophysiological determinations of criterion amplitudes of slow-wave responses from single retinal cells. Traditional flash methods can require tedious dark adaptations and may yield erroneous spectral sensitivity curves which are not seen in such modifications as ramp methods. Linear response methods involve interferometry, while constant response methods involve manual or automatic adjustments of continuous illumination to keep response amplitudes constant during spectral scans. In DC or AC computerized constant response methods, feedback to determine intensities at each wavelength is derived from the response amplitudes themselves. Although all but traditional flash methods have greater or lesser abilities to provide on-line determinations of spectral sensitivities, computerized constant response methods are the most satisfactory due to flexibility, speed and maintenance of a constant adaptation level

Further analysis of open-respirometry systems: an a-compartmental mechanistic approach

A system is said to be "instantaneous" when for a given constant input an equilibrium output is obtained after a while. In the meantime, the output is changing from its initial value towards the equilibrium one. This is the transient period of the system and transients are important features of open-respirometry systems. During transients, one cannot compute the input amplitude directly from the output. The existing models (e.g., first or second order dynamics) cannot account for many of the features observed in real open-respirometry systems, such as time lag. Also, these models do not explain what should be expected when a system is speeded up or slowed down. The purpose of the present study was to develop a mechanistic approach to the dynamics of open-respirometry systems, employing basic thermodynamic concepts. It is demonstrated that all the main relevant features of the output dynamics are due to and can be adequately explained by a distribution of apparent velocities within the set of molecules travelling along the system. The importance of the rate at which the molecules leave the sensor is explored for the first time. The study approaches the difference in calibrating a system with a continuous input and with a "unit impulse": the former truly reveals the dynamics of the system while the latter represents the first derivative (in time) of the former and, thus, cannot adequately be employed in the apparent time-constant determination. Also, we demonstrate why the apparent order of the output changes with volume or flow.