937 resultados para Coefficient of determination


Relevância:

90.00% 90.00%

Publicador:

Resumo:

Crushing and grinding are the most energy intensive part of the mineral recovery process. A major part of rock size reduction occurs in tumbling mills. Empirical models for the power draw of tumbling mills do not consider the effect of lifters. Discrete element modelling was used to investigate the effect of lifter condition on the power draw of tumbling mill. Results obtained with PFC3D code show that lifter condition will have a significant influence on the power draw and on the mode of energy consumption in the mill. Relatively high lifters will consume less power than low lifters, under otherwise identical conditions. The fraction of the power that will be consumed as friction will increase as the height of the lifters decreases. This will result in less power being used for high intensity comminution caused by the impacts. The fraction of the power that will be used to overcome frictional resistance is determined by the material's coefficient of friction. Based on the modelled results, it appears that the effective coefficient of friction for in situ mill is close to 0.1. (C) 2003 Elsevier Science Ltd. All rights reserved.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

An equivalent unit cell waveguide approach (WGA) is described to obtain reflection coefficient phase curves for designing a microstrip patch reflectarray supported by a ground plane with periodic apertures or slots. Based on the presented theory, a computer algorithm for determining the reflection coefficient of a plane wave normally incident on a multi-layer structure of patches and apertures is developed. The validity of the developed algorithm is verified by comparing the obtained results with those published in the literature and the ones generated by Agilent High Frequency Structure Simulator (HFSS). A good agreement in all the presented examples is obtained, proving that the developed theory and computer algorithm can be an effective tool for designing multi-layer microstrip reflectarrays with a periodically perforated ground plane. (C) 2003 Wiley Periodicals, Inc.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

The purpose of the present study was to examine the reproducibility of laboratory-based 40-km cycle time-trial performance on a stationary wind-trainer. Each week, for three consecutive weeks, and on different days, forty-three highly trained male cyclists ((x) over bar +/- SD; age = 25 +/- 6 y; mass = 75 +/- 7 kg; peak oxygen uptake [(V) over dot O-2 peak] = 64.8 +/- 5.2 ml x kg(-1) x min(-1)) performed: 1) a (V) over dot O-2 peak test, and 2) a 40-km time-trial on their own racing bicycle mounted to a stationary wind-trainer (Cateye - Cyclosimulator). Data from all tests were compared using a one-way analysis of variance. Performance on the second and third 40-km time-trials were highly related (r = 0.96; p < 0.001), not significantly different (57:21 +/- 2:57 vs. 57:12 +/- 3:14 min:s), and displayed a low coefficient of variation (CV) = 0.9 +/- 0.7%. Although the first 40-km time-trial (58:43 +/- 3:17min:s) was not significantly different from the second and third tests (p = 0.06), inclusion of the first test in the assessment of reliability increased within-subject CV to 3.0 +/- 2.9%. 40-km time-trial speed (km x h(-1)) was significantly (p < 0.001) related to peak power output (W; r = 0.75), (V) over dot O-2 peak (1 x min(-1); r = 0.53), and the second ventilatory turnpoint (1 x min(-1); r = 0.68) measured during the progressive exercise tests. These data demonstrate that the assessment of 40-km cycle time-trial performance in well-trained endurance cyclists on a stationary wind-trainer is reproducible, provided the athletes perform a familiarization trial.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Three different particular geometrical shapes of parallelepiped, cylinder and sphere were taken from cut green beans (length:diameter = 1:1, 2:1 and 3:1) and potatoes (aspect ratio = 1:1, 2:1 and 3:1) and peas, respectively. Their drying behaviour in a fluidised bed was studied at three different drying temperatures of 30, 40 and 50 degreesC (RH = 15%). Drying curves were constructed using non-dimensional moisture ratio (MR) and time and their behaviour was modelled using exponential (MR = exp(-kt)) and Page (MR = exp(-kt(n))) models. The effective diffusion coefficient of moisture transfer was determined by Fickian method using uni- and three-dimensional moisture movements. The diffusion coefficient was least affected by the size when the moisture movement was considered three-dimensional, whereas the drying temperature had a significative effect on diffusivity as expected. The drying constant and diffusivity coefficients were on the descending order for potato, beans and peas. The Arrhenius activation energy for the peas was also highest, indicating a strong barrier to moisture movement in peas as compared to beans and skinless cut potato pieces. (C) 2003 Elsevier Science Ltd. All rights reserved.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

O cultivo do café é uma das atividades do agronegócio de maior importância socioeconômica dentre as diferentes atividades ligadas ao comércio agrícola mundial. Uma das maiores contribuições da genética quantitativa para o melhoramento genético é a possibilidade de prever ganhos genéticos. Quando diferentes critérios de seleção são considerados, a predição de ganhos referentes a cada critério tem grande importância, pois indica os melhoristas sobre como utilizar o material genético disponível, visando obter o máximo de ganhos possível para as características de interesse. O presente trabalho foi instalado em julho de 2004, na Fazenda Experimental de Bananal do Norte, conduzida pelo Incaper, no distrito de Pacotuba, município de Cachoeiro de Itapemirim, região Sul do Estado, com o objetivo de selecionar as melhores plantas entre e dentro de progênies de meios- irmãos de Coffea canephora, por meio de diferentes critérios de seleção. Foram realizadas análises de variância individuais e conjuntas para 26 progênies de meios- irmãos Coffea canephora. O delineamento experimental utilizado foi em blocos ao acaso com quatro testemunhas adicionais com quatro repetições e parcela composta por cinco plantas, com o espaçamento de 3,0 m x 1,2 m. Neste trabalho, considerou-se os dados das últimas cinco colheitas. As características mensuradas foram: florescimento, maturação, tamanho do grão, peso, porte, vigor, ferrugem, mancha cercóspora, seca de ponteiros, escala geral, porcentagem de frutos boia e bicho mineiro. Todas as análises estatísticas foram realizadas com o aplicativo computacional em genética e estatística (GENES). Foram estimados os ganhos de seleção em função da porcentagem de seleção de 20% entre e dentro, sendo as mesmas mantidas para todas as características. Todas as características foram submetidas a seleção no sentido positivo, exceto para florescimento, porte, ferrugem, mancha cercóspora, seca de ponteiros, porcentagem de frutos boia e bicho mineiro, para obter decréscimo em suas médias originais. Os critérios de seleção estudados foram: seleção convencional entre e dentro das famílias, índice de seleção combinada, seleção massal e seleção massal estratificada. Esta dissertação é composta por dois capítulos, em que foram realizadas análises biométricas, como a obtenção de estimativas de parâmetros genéticos. Na maioria das características estudadas, verificaram-se diferenças significativas (P<0,05) para genótipos que, associados aos coeficientes de variação genotípicos e também ao coeficiente de determinação genotípico e à relação CVg/CVe, indicam a existência de variabilidade genética nos materiais genéticos para a maioria das características e condições favoráveis para obtenção de ganhos genéticos pela seleção. Essas características também foram correlacionadas. Os dados foram submetidos às análises de variância e multivariada, aplicando-se a técnica de agrupamento e UPGMA, teste de médias e estudo de correlações. Na técnica de agrupamento, foi utilizada a distância generalizada de Mahalanobis como medida de dissimilaridade, e na delimitação dos grupos, o método de Tocher. Foi encontrada diversidade genética para as características associadas à qualidade fisiológica, mobilização de reserva das sementes, dimensões e biomassa das plântulas. Quatro grupos de genótipos puderam ser formados. Peso de massa seca de sementes, redução de reserva de sementes e peso de massa seca de plântulas estão positivamente correlacionados entre si, enquanto a redução de reserva das sementes e a eficiência na conversão dessas reservas em plântulas estão negativamente correlacionadas. De acordo com os resultados obtidos, verificou-se que todas as características apresentaram níveis diferenciados de variabilidade genética e os critérios de seleção utilizados mostraram-se eficientes para o melhoramento, no qual o índice de seleção combinada é o critério de seleção que apresentou os melhores resultados em termos de ganhos, sendo indicado como critério mais apropriado para o melhoramento genético da população estudada. Nos estudos de correlações, em 70% dos casos, a correlação fenotípica foi superior à genotípica, mostrando maior influência dos fatores ambientais em relação aos genotípicos e condições propícias ao melhoramento dos diferentes caracteres. No estudo de divergência genética, observou-se que pelo agrupamento de genótipos, pela técnica de Tocher, indicou que os genótipos foram distribuídos em três grupos.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

The objective of this study was to analyze the environmental performance of aquaculture in the city of Colorado do Oeste, Rondônia State, Brazil. Fifteen fish farmers were interviewed. For data collection, structured interviews were carried out, using a questionnaire based on information supplied by the United Nations Food and Agriculture Organization (FAO). The questionnaire considered 12 items, organized into three main topics: a) social and legal standards b) environmental standards c) standards of food safety and hygiene. The questionnaire considered 12 items, organized into three main topics: a) social and legal standards b) environmental standards c) standards of food safety and hygiene. Aquaculture in the city of Colorado do Oeste, Rondônia presents two fish production systems: extensive and semi-intensive. In the semi-intensive system, stocking rate was one fish per m3, on average; tambaqui (Colossoma macropomum), tilapias (Oreochromis spp.), pirarucu (Arapaima gigas) and pintado (Pseudoplatystoma spp.) were the species farmed at the largest number. The rate of water renewal was due to the greater availability of natural food in this system. Water renewal was constant in the ponds (1,500 liters per minute). In the semi-intensive system using dug ponds, alevins were stocked and fed during the entire rearing time with natural and exogenous food. The extensive system relied on the natural production of the pond, with stocking density limited by the production of natural food. The little renewal of water made the cultivation tank itself acted as a decantation lake, with the occurrence of oxidation and sedimentation of residual organic matter, consisting of feces, debris and organic fertilizer. Production of reduced effluent volume took place in the extensive system, compared to the cultivation area. In addition, there was high water turbidity, caused by high concentration of planktonic organisms, and low concentrations of dissolved oxygen in the water. Data showed that nine estates of the interviewed fish farmers had critical environmental performance (less than 30.0%). Six estates of fish farmers had bad environmental performance (between 30.0 and 50.0%) (Coefficient of sustentainability = green square x 100 ÷ Total Questions less the yellow squares)

Relevância:

90.00% 90.00%

Publicador:

Resumo:

One of the current frontiers in the clinical management of Pectus Excavatum (PE) patients is the prediction of the surgical outcome prior to the intervention. This can be done through computerized simulation of the Nuss procedure, which requires an anatomically correct representation of the costal cartilage. To this end, we take advantage of the costal cartilage tubular structure to detect it through multi-scale vesselness filtering. This information is then used in an interactive 2D initialization procedure which uses anatomical maximum intensity projections of 3D vesselness feature images to efficiently initialize the 3D segmentation process. We identify the cartilage tissue centerlines in these projected 2D images using a livewire approach. We finally refine the 3D cartilage surface through region-based sparse field level-sets. We have tested the proposed algorithm in 6 noncontrast CT datasets from PE patients. A good segmentation performance was found against reference manual contouring, with an average Dice coefficient of 0.75±0.04 and an average mean surface distance of 1.69±0.30mm. The proposed method requires roughly 1 minute for the interactive initialization step, which can positively contribute to an extended use of this tool in clinical practice, since current manual delineation of the costal cartilage can take up to an hour.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Seventy four asthmatic children aged 7 to 11 years were examined along with controls matched by age and sex. Clinical and laboratory investigations preceded a 28-day follow-up where data about morning and evening peak expiratory flow rate (PEF), symptoms and treatment were recorded. The coefficient of variation of PEF was found to be an objective measurement of asthma severity that has statistically significant correlation with both symptoms (r s= .36) and treatment (r s= .60). Moreover, it separates mild and severe asthmatics, as confirmed by statistically significant differences (p= .008 or less) in symptoms, treatment, skin allergy and airways response to exercise. Skin allergy and airways responsiveness to exercise were found to be predictors of both disease and severity. By means of logistic regression analysis it was possible to establish the probabilities for both asthma and severe asthma when children presenting and not presenting these characteristics are compared. One single positive skin test represent a probability of 88% for the development of asthma and a probability of 70% for severe disease. A PEF reduction of 10% after an exercise test implies a probability of 73% for disease and a probability of 64% for severe disease. Increases in these variables imply geometrically increased risks and their presence together have a multiplicative effect in the final risk.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

A replicate evaluation of increased micronucleus (MN) frequencies in peripheral lymphocytes of workers occupationally exposed to formaldehyde (FA) was undertaken to verify the observed effect and to determine scoring variability. May–Grünwald–Giemsa-stained slides were obtained from a previously performed cytokinesis-block micronucleus test (CBMNT) with 56 workers in anatomy and pathology laboratories and 85 controls. The first evaluation by one scorer (scorer 1) had led to a highly significant difference between workers and controls (3.96 vs 0.81 MN per 1000 cells). The slides were coded before re-evaluation and the code was broken after the complete re-evaluation of the study. A total of 1000 binucleated cells (BNC) were analysed per subject and the frequency of MN (in ‰) was determined. Slides were distributed equally and randomly between two scorers, so that the scorers had no knowledge of the exposure status. Scorer 2 (32 exposed, 36 controls) measured increased MN frequencies in exposed workers (9.88 vs 6.81). Statistical analysis with the two-sample Wilcoxon test indicated that this difference was not significant (p = 0.17). Scorer 3 (20 exposed, 46 controls) obtained a similar result, but slightly higher values for the comparison of exposed and controls (19.0 vs 12.89; p = 0.089). Combining the results of the two scorers (13.38 vs 10.22), a significant difference between exposed and controls (p = 0.028) was obtained when the stratified Wilcoxon test with the scorers as strata was applied. Interestingly, the re-evaluation of the slides led to clearly higher MN frequencies for exposed and controls compared with the first evaluation. Bland–Altman plots indicated that the agreement between the measurements of the different scorers was very poor, as shown by mean differences of 5.9 between scorer 1 and scorer 2 and 13.0 between scorer 1 and scorer 3. Calculation of the intra-class correlation coefficient (ICC) revealed that all scorer comparisons in this study were far from acceptable for the reliability of this assay. Possible implications for the use of the CBMNT in human biomonitoring studies are discussed.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

OBJECTIVE: To describe the effects of social inequities on the health and nutrition of children in low and middle income countries. METHODS: We reviewed existing data on socioeconomic disparities within-countries relative to the use of services, nutritional status, morbidity, and mortality. A conceptual framework including five major hierarchical categories affecting inequities was adopted: socioeconomic context and position, differential exposure, differential vulnerability, differential health outcomes, and differential consequences. The search of the PubMed database since 1990 identified 244 articles related to the theme. Results were also analyzed from almost 100 recent national surveys, including Demographic Health Surveys and the UNICEF Multiple Indicator Cluster Surveys. RESULTS: Children from poor families are more likely, relative to those from better-off families, to be exposed to pathogenic agents; once they are exposed, they are more likely to become ill because of their lower resistance and lower coverage with preventive interventions. Once they become ill, they are less likely to have access to health services and the quality of these services is likely to be lower, with less access to life-saving treatments. As a consequence, children from poor family have higher mortality rates and are more likely to be undernourished. CONCLUSIONS: Except for child obesity and inadequate breastfeeding practices, all the other adverse conditions analyzed were more prevalent in children from less well-off families. Careful documentation of the multiple levels of determination of socioeconomic inequities in child health is essential for understanding the nature of this problem and for establishing interventions that can reduce these differences.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Purpose - To develop and validate a psychometric scale for assessing image quality perception for chest X-ray images. Methods - Bandura's theory was used to guide scale development. A review of the literature was undertaken to identify items/factors which could be used to evaluate image quality using a perceptual approach. A draft scale was then created (22 items) and presented to a focus group (student and qualified radiographers). Within the focus group the draft scale was discussed and modified. A series of seven postero-anterior chest images were generated using a phantom with a range of image qualities. Image quality perception was confirmed for the seven images using signal-to-noise ratio (SNR 17.2–36.5). Participants (student and qualified radiographers and radiology trainees) were then invited to independently score each of the seven images using the draft image quality perception scale. Cronbach alpha was used to test interval reliability. Results - Fifty three participants used the scale to grade image quality perception on each of the seven images. Aggregated mean scale score increased with increasing SNR from 42.1 to 87.7 (r = 0.98, P < 0.001). For each of the 22 individual scale items there was clear differentiation of low, mid and high quality images. A Cronbach alpha coefficient of >0.7 was obtained across each of the seven images. Conclusion - This study represents the first development of a chest image quality perception scale based on Bandura's theory. There was excellent correlation between the image quality perception scores derived using the scale and the SNR. Further research will involve a more detailed item and factor analysis.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Variations of manufacturing process parameters and environmental aspects may affect the quality and performance of composite materials, which consequently affects their structural behaviour. Reliability-based design optimisation (RBDO) and robust design optimisation (RDO) searches for safe structural systems with minimal variability of response when subjected to uncertainties in material design parameters. An approach that simultaneously considers reliability and robustness is proposed in this paper. Depending on a given reliability index imposed on composite structures, a trade-off is established between the performance targets and robustness. Robustness is expressed in terms of the coefficient of variation of the constrained structural response weighted by its nominal value. The Pareto normed front is built and the nearest point to the origin is estimated as the best solution of the bi-objective optimisation problem.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

OBJECTIVE To evaluate the validity and reliability of an instrument that evaluates the structure of primary health care units for the treatment of tuberculosis.METHODS This cross-sectional study used simple random sampling and evaluated 1,037 health care professionals from five Brazilian municipalities (Natal, state of Rio Grande do Norte; Cabedelo, state of Paraíba; Foz do Iguaçu, state of Parana; Sao José do Rio Preto, state of Sao Paulo, and Uberaba, state of Minas Gerais) in 2011. Structural indicators were identified and validated, considering different methods of organization of the health care system in the municipalities of different population sizes. Each structure represented the organization of health care services and contained the resources available for the execution of health care services: physical resources (equipment, consumables, and facilities); human resources (number and qualification); and resources for maintenance of the existing infrastructure and technology (deemed as the organization of health care services). The statistical analyses used in the validation process included reliability analysis, exploratory factor analysis, and confirmatory factor analysis.RESULTS The validation process indicated the retention of five factors, with 85.9% of the total variance explained, internal consistency between 0.6460 and 0.7802, and quality of fit of the confirmatory factor analysis of 0.995 using the goodness-of-fit index. The retained factors comprised five structural indicators: professionals involved in the care of tuberculosis patients, training, access to recording instruments, availability of supplies, and coordination of health care services with other levels of care. Availability of supplies had the best performance and the lowest coefficient of variation among the services evaluated. The indicators of assessment of human resources and coordination with other levels of care had satisfactory performance, but the latter showed the highest coefficient of variation. The performance of the indicators “training” and “access to recording instruments” was inferior to that of other indicators.CONCLUSIONS The instrument showed feasibility of application and potential to assess the structure of primary health care units for the treatment of tuberculosis.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Human mesenchymal stem/stromal cells (MSCs) have received considerable attention in the field of cell-based therapies due to their high differentiation potential and ability to modulate immune responses. However, since these cells can only be isolated in very low quantities, successful realization of these therapies requires MSCs ex-vivo expansion to achieve relevant cell doses. The metabolic activity is one of the parameters often monitored during MSCs cultivation by using expensive multi-analytical methods, some of them time-consuming. The present work evaluates the use of mid-infrared (MIR) spectroscopy, through rapid and economic high-throughput analyses associated to multivariate data analysis, to monitor three different MSCs cultivation runs conducted in spinner flasks, under xeno-free culture conditions, which differ in the type of microcarriers used and the culture feeding strategy applied. After evaluating diverse spectral preprocessing techniques, the optimized partial least square (PLS) regression models based on the MIR spectra to estimate the glucose, lactate and ammonia concentrations yielded high coefficients of determination (R2 ≥ 0.98, ≥0.98, and ≥0.94, respectively) and low prediction errors (RMSECV ≤ 4.7%, ≤4.4% and ≤5.7%, respectively). Besides PLS models valid for specific expansion protocols, a robust model simultaneously valid for the three processes was also built for predicting glucose, lactate and ammonia, yielding a R2 of 0.95, 0.97 and 0.86, and a RMSECV of 0.33, 0.57, and 0.09 mM, respectively. Therefore, MIR spectroscopy combined with multivariate data analysis represents a promising tool for both optimization and control of MSCs expansion processes.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Thirty-two patients bitten by venomous snakes sixteen by Bothrops spp. and sixteen by Crotalus durissus terrificus were studied. The group comprised thirty males and two females, aged eight to sixty-three years (mean 33±15). Bromsulphalein tests were increased in the majority of patients bitten by Crotalus durissus terrificus. The correlation coefficient of Spearman was positive between bromsulphalein tests and alanine aminotransferase levels, and between alanine aminotransferase and aspartate aminotransferase levels only in the Crotalus group. The only patient who died was bitten by Crotalus durissus terrificus and showed hydropic degeneration and mitochondrial injury in the liver. It was concluded that the hepatic damage might have been caused by at least two possible mechanisms: venom effect on liver mitochondria and cytokine effects on hepatocyte, specially interleukin-6.