General model of a foam bed reactor

A general model of a foam bed reactor has been developed which rigorously accounts for the extent of gas absorption with chemical reaction occurring in both the storage and foam sections. Its applicability extends to a wide spectrum of reaction velocities. The possibilities of the predominance of the bulk-liquid reaction in the storage section or the absorption with reaction in the foam section can be handled as merely special cases of the general analysis. The importance of foam for carrying out a particular gas-liquid reaction is characterised by a criterion in terms of the fractional rate of reaction in the foam section. Trends of variations in the concentrations of dissolved free A, solute B, and gas-phase A with time of operation of the reactor are presented. The nature of the variation in the fractional rate of reaction in the foam section with time, at different reaction velocities, and the effect of the liquid flow rate (across the storage section) on the transience are also illustrated. Finally, the predictions of the general model have been validated using the available experimental data on the oxidation of sodium sulphide in a foam bed reactor. The agreement between the experimental and the present theoretical information is fairly good, apart from being more insightful than all the previous models of this reactor.

Kaupunkipurot Helsingissä - Veden laatu vuonna 2004

In recent years urban hydrology and individual urban streams have been in focus and subjects to research also in Helsinki. However, until now there has been lack of research covering simultaneously the whole area of the city of Helsinki. The aim of this study was to find out the general state of water quality in small urban streams in the city of Helsinki. 21 streams were studied: Mätäjoki, Korppaanoja, Mätäpuro, Näsinoja-Tuomarinkylänoja, Tuomarinkartanonpuro, Kumpulanpuro, Tapaninkylänpuro, Tapaninvainionpuro, Puistolanpuro, Longinoja, Säynäslahdenpuro, Viikinoja, Porolahdenpuro, Mustapuro, Marjaniemenpuro, Mellunkylänpuro, Vuosaarenpuro, Rastilanpuro, Ramsinkannaksenpuro, Skatanpuro and Yliskylänpuro. Water samples were collected from 48 sampling points, each stream having at least one point. Four water samples were collected from each point, sampling periods being 9.-11.2., 26.-28.4., 29.6.-1.7. and 25.-27.10.2004. Field measurements associated with water sampling included water temperature, oxygen concentration, pH and electrical conductivity. Water samples were analysed in the Laboratory of Physical Geography in the University of Helsinki and in the Environmental Laboratory of the City of Helsinki Environment Centre for following properties: suspended solids, dissolved substances, alkalinity, principal anions and cations (Na+, K+, Mg2+, Ca2+, F-, Cl-, NO3-, PO43- and SO42-), colour, turbidity, biological and chemical oxygen demand (BOD7 and CODMn-values), nutrient concentrations and bacterial indicators of hygienic quality. The main water quality issues found in this study were low oxygen levels in many streams and poor hygienic quality at least occasionally. E.g. in summer oxygen levels were under 60 % in every stream. Amount of total dissolved substances and nutrients were high in some of the streams studied. Compared to other Finnish streams the values of alkalinity and pH were higher. Although these problems were common, the variation between different streams and sampling points was significant. This was probably due to local conditions. Best overall water quality was found in Mätäpuro and Tuomarinkartanonpuro streams. Seasonal variation was evident in almost all water quality properties. For example the total amount of dissolved substances was largest in winter and decreased during the year. Colour and turbidity were smallest in winter and increased towards the end of the year. The same was true for suspended solids, which had smallest concentration in winter and greatest in autumn. It must be kept in mind that the spring samples were collected after the spring flood otherwise the largest suspended solid concentrations would have been expected in spring. Finnish general water quality classification was used to assess the quality of urban stream waters. Its suitability for small urban streams is not, however, completely trouble-free. This classification does not take into account the quick changes in such small streams but evaluates only the yearly mean values. This can oversimplify the picture of the water quality situation in the streams. Also in order to better reflect the urban environment the analysed water quality properties should also include total dissolved substances and e.g. concentrations of chloride and sodium.

Controlled combustion synthesis and properties of fine-particle NASICON materials

Fine-particle NASICON materials, Na1+xZr2P3-xSixO12 (where x = 0.0, 0.5, 1.0, 1.5, 2.0 and 2.5), have been prepared by controlled combustion of an aqueous solution containing stoicthiometric amounts of sodium nitrate, zirconyl nitrate, ammonium perchlorate, diammonium hydrogen phosphate, fumed silica and carbonohydrazide. Formation of NASICON has been confirmed by powder XRD, Si-29 NMR and IR spectroscopy. These NASICON powders are fine (average agglomerate size 5-12 mum) with a surface area varying from 8 to 30 m2 g-1. NASICON powders pelletized and sintered at 1100-1200-degrees-C for 5 h achieved 90-95% theoretical density and show fine-grain microstructure. The coefficient of thermal expansion of sintered NASICON compact was measured up to 500-degrees-C and changes f rom -3.4 x 10(-6) to 4.1 x 10(-6) K-1. The conductivity of Sintered Na3Zr2PSi2O12 compact at 300-degrees-C is 0.236 OMEGA-1 cm-1.

Differential pulse polarographic determination of trace levels of iron(III) by using the catalytic current

Trace of iron(III) are determined by differential pulse polarography in a medium of sodium hydroxide and sodium bromate using the catalytic current. Various cations do not interfere. The relative standard deviation is 2%.

Photolabeling of the EcoP15 DNA methyltransferase with S-adenosyl-l-methionine

Radioactivity from S-adenosyl-L-[methyl-H-3] methionine ([methyl-H-3]AdoMet) was bound to the EcoP15 DNA methyltransferase (M.EcoP15) following short-wave ultraviolet (UV) irradiation. The labeled protein was subjected to polyacrylamide-gel electrophoresis in the presence of sodium dodecyl sulfate (SDS-PAGE), and detected by fluorography and autoradiography. Labeling was found to be dependent on the concentration of AdoMet and time of UV irradiation. The photolabeling by [methyl-H-3]AdoMet was specific and blocked by S-adenosyl-L-homocysteine (AdoHcy) and sinefungin which are known to function as competitive inhibitors. Limited digestion of the M EcoP15-AdoMet adduct by Staphylococcus aureus protease V8 generated three peptides of approx. 50, 32 and 30 kDa; Interestingly, only the 30-kDa peptide fragment contained radioactivity, as detected by SDS-PAGE, followed by fluorography and autoradiography. Further, sequencing of a few amino acids at the N-terminus of these peptides showed that the 30-kDa fragment was the N-terminal portion of M.EcoP15, These results suggest that photolabeling is at the AdoMet-binding site and that the N-terminal half of M.EcoP15 may be involved in substrate binding.

Reduction of quinolines to 1,2,3,4-tetrahydro derivatives employing a combination of NaCNBH3 and BF3.OEt(2)

A regiospecific reduction of quinolines (and 1,10-phenanthroline) into the corresponding 1,2,3,4-tetrahydro derivatives using a combination of sodium cyanoborohydride and boron trifluoride etherate in refluxing methanol is described. Under the same conditions indole and acridine reduced to the corresponding dihydroderivatives, whereas acyl group transfer from oxygen to nitrogen atom is also noticed in the case of 8-acyloxyquinolines.

Plume structure in high-Rayleigh-number convection

Near-wall structures in turbulent natural convection at Rayleigh numbers of $10^{10}$ to $10^{11}$ at A Schmidt number of 602 are visualized by a new method of driving the convection across a fine membrane using concentration differences of sodium chloride. The visualizations show the near-wall flow to consist of sheet plumes. A wide variety of large-scale flow cells, scaling with the cross-section dimension, are observed. Multiple large-scale flow cells are seen at aspect ratio (AR)= 0.65, while only a single circulation cell is detected at AR= 0.435. The cells (or the mean wind) are driven by plumes coming together to form columns of rising lighter fluid. The wind in turn aligns the sheet plumes along the direction of shear. the mean wind direction is seen to change with time. The near-wall dynamics show plumes initiated at points, which elongate to form sheets and then merge. Increase in rayleigh number results in a larger number of closely and regularly spaced plumes. The plume spacings show a common log–normal probability distribution function, independent of the rayleigh number and the aspect ratio. We propose that the near-wall structure is made of laminar natural-convection boundary layers, which become unstable to give rise to sheet plumes, and show that the predictions of a model constructed on this hypothesis match the experiments. Based on these findings, we conclude that in the presence of a mean wind, the local near-wall boundary layers associated with each sheet plume in high-rayleigh-number turbulent natural convection are likely to be laminar mixed convection type.

Mitigation of Alkali Induced Heave in Rectorite Soil with Fly Ash

Mechanisms that control the volume changes behavior of foundation soils are well understood. The changes that occur in the behavior of soil due to migration of pollutants are not well understood. The extent of changes that occur in the presence of small concentration of contaminants can be predicted based on changes in the thickness of double layer and associated fabric changes. Interactions that occur with strong contaminants depends on the type of soil, type and concentration of contamination and duration of interaction etc It has been shown that different concentrations (1N and 4N) of sodium hydroxide solution causes abnormal changes on volume change behaviour of soil due to mineralogical changes. An attempt is made in this paper to stabilize contaminated soil using fly ash, after establishing its stability in alkali solutions. It was found that the effectiveness of fly ash to control the alkali induced heave increases with fly ash content incorporated into the soil. X-ray diffraction studies reveal that the mineralogical changes that occur in soil due to alkali interaction are inhibited by the presence of fly ash.

A Reliable method of obtaining Breakthrough Curves of ions in Soils using Transport Equation

Molecular diffusion plays a dominant role in transport of contaminants through fine-grained soils with low hydraulic conductivity. Attenuation processes occur while contaminants travel through the soils. Effective diffusion coefficient (De) is expected to take into consideration various attenuation processes. Effective diffusion coefficient has been considered to develop a general approach for modelling of contaminant transport in soils.The effective diffusion coefficient of sodium in presence of sulphate has been obtained using the column test.The reliability of De, has been checked by comparing theoretical breakthrough curves of sodium ion in soils obtained using advection diffusion equation with the experimental curve.

Kinetics of Sulphation of Nickel and Cobalt Ferrites with Na$O, Melt Containing F'e3+ Ions

It has been experimentally established that nickel and cobalt can be extracted from their ferrites with sodium sulphate melt containing femc ions. The kinetics of extraction from synthetic ferrites using a melt of sodium and ferric sulphates of eutectic composition has been studied as a function of the particle size of the ferrite and temperature in the range 900 to 1073 K. The divalent ions in the ferrite exchange with the ferric ion in the melt, leaving a residue of hematite.The rate of reaction conforms to the Crank-Ginstling-Brounshtein diffusion model. The reaction rate is governed by the counter-diffusion of ~ e an~d ~+i ' +(or co2+) ions in the hematite lattice. Analytical expressions for the rate constants have been derived from the experimental data as a function of particle size and temperature. The activation energy for the extraction of nickel from nickel ferrite is 154(+10) kJ mol-' and the corresponding value for cobalt is 142(+10)kJ mol;'. In sulphation roasting of minerals containing nickel, the yield of nickel is generally limited to 75% due to the formation of insoluble ferrites. The use of melts based on sodium sulphate provides a possible route for enhancing the recovery of nickel to approximately 98%.

Role of the cesium antimonide layer in the Na2KSb/Cs3Sb photocathode

When radiation of sufficiently high energy is incident on the surface of a semiconductor photocathode, electrons are excited from the valence band to the conduction band and these may contribute to the photocurrent. The photocurrent in a single-layer cathode is found to be small, because of collisions within the cathode material, the electron affinity condition, etc. It is observed that when a thin layer of n-type cesium antimonide (Cs3Sb) is deposited over a p-type layer of sodium potassium antimonide (Na2KSb), there occurs a sharp rise in the photocurrent. The causes for the dramatic increase in the photocurrent obtainable from a sodium potassium antimonide cathode, by depositing a thin layer of cesium antimonide are analyzed in this article. It has been shown that the interface between sodium potassium antimonide and cesium antimonide can result in lowering of the electron affinity to a level below the bottom of the conduction band of sodium potassium antimonide. The drift field that arises at the heterointerface enables the electrons to reach the surface, leading to the emission of almost all the photogenerated electrons within the cathode. The processes involved in photoemission from such a double-layer cathode are examined from a theoretical point of view. The spectral response of the two-layer cathode is also found to be better than that of a single-layer cathode.

Electrochemical oxidation of boron containing compounds on titanium carbide and its implications to direct fuel cells

Electrochemical oxidation of sodium borohydride (NaBH(4)) and ammonia borane (NH(3)BH(3)) (AB) have been studied on titanium carbide electrode. The oxidation is followed by using cyclic voltammetry, chronoamperometry and polarization measurements. A fuel cell with TiC as anode and 40 wt% Pt/C as cathode is constructed and the polarization behaviour is studied with NaBH(4) as anodic fuel and hydrogen peroxide as catholyte. A maximum power density of 65 mW cm(-2) at a load current density of 83 mA cm(-2) is obtained at 343 K in the case of borhydride-based fuel cell and a value of 85 mW cm(-2) at 105 mA cm(-2) is obtained in the case of AB-based fuel cell at 353 K. (C) 2011 Elsevier Ltd. All rights reserved.

EFFECT OF CORE-SHELL STRUCTURE OF HYDROGEL BEADS ON THE THRESHOLD CONCENTRATION OF WATER FOR SWELLING AND ITS PH SENSITIVITY

In this paper we investigate the effect of core-shell structure of Sodium Alginate based hydrogel beads and their size on certain activation threshold concentration of water for applications in swelling and pH sensing. This type of hydrogel experiences diffusive pressure due to transport of certain free charges across its interface with a solvent or electrolyte. This process is essentially a dynamic equilibrium of the electric force field, stress in the polymeric network with cage like structure and molecular diffusion including phase transformation due to pressure imbalance between the hydrogel and its surroundings. The effect of pH of the solvant on the swelling rate of these beads has been studied experimentally. A mathematical model of the swelling process has been developed by considering Nernst-Planck equation representing the migration of mobile ions and Er ions, Poisson equation representing the equilibrium of the electric field and mechanical field equation representing swelling of the gel. An attempt has been made to predict the experimentally observed phenomena using these numerical simulations. It is observed experimentally that certain minimum concentration called activation threshold concentration of the water molecules must be present in the hydrogel in order to activate the swelling process. For the required activation threshold concentration of water in the beads, the pH induced change in the rate of swelling is also investigated. This effect is analyzed for various different core-shell structures of the beads.

pH Induced switching in hydrogel coated fiber bragg grating sensor

In this paper we report a novel hydrogel functionalized optical Fiber Bragg Grating (FBG) sensor based on chemo-mechanical-optical sensing, and demonstrate its specific application in pH activated process monitoring. The sensing mechanism is based on the stress due to ion diffusion and polymer phase transition which produce strain in the FBG. This results in shift in the Bragg wavelength which is detected by an interrogator system. A simple dip coating method to coat a thin layer of hydrogel on the FBG has been established. The gel consists of sodium alginate and calcium chloride. Gel formation is observed in real-time by continuously monitoring the Bragg wavelength shift. We have demonstrated pH sensing in the range of pH of 2 to 10. Another interesting phenomenon is observed by swelling and deswelling of FBG functionalized with hydrogel by a sequence of alternate dipping between acidic and base solutions. It is observed that the Bragg wavelength undergoes reversible and repeatable pH dependent switching.

A naturally occurring amino acid substitution in the voltage-dependent sodium channel selectivity filter affects channel gating

The pore of sodium channels contains a selectivity filter made of 4 amino acids, D/E/K/A. In voltage sensitive sodium channel (Nav) channels from jellyfish to human the fourth amino acid is Ala. This Ala, when mutated to Asp, promotes slow inactivation. In some Nav channels of pufferfishes, the Ala is replaced with Gly. We studied the biophysical properties of an Ala-to-Gly substitution (A1529G) in rat Nav1.4 channel expressed in Xenopus oocytes alone or with a beta 1 subunit. The Ala-to-Gly substitution does not affect monovalent cation selectivity and positively shifts the voltage-dependent inactivation curve, although co-expression with a beta 1 subunit eliminates the difference between A1529G and WT. There is almost no difference in channel fast inactivation, but the beta 1 subunit accelerates WT current inactivation significantly more than it does the A1529G channels. The Ala-to-Gly substitution mainly influences the rate of recovery from slow inactivation. Again, the beta 1 subunit is less effective on speeding recovery of A1529G than the WT. We searched Nav channels in numerous databases and noted at least four other independent Ala-to-Gly substitutions in Nav channels in teleost fishes. Thus, the Ala-to-Gly substitution occurs more frequently than previously realized, possibly under selection for alterations of channel gating.