Estudo da obtenção de cerâmica composta de alumina e beta alumina sódica utilizando-se resíduo cerâmico de velas de ignição e pó químico de extintores de incêndio

Ceramic materials the alumina base are large industrial applications. They are required for these products, specific characteristics obtained by following strict criteria during the manufacturing process. However, after life, not always these products are reused by a suitable waste management process. In ceramist context, advance research aimed at the reuse of waste aimed at obtaining ceramics and composite materials, with marked reduction of conventional raw materials. Aiming to generate scientific, technological and environmental contribution, this work studied to obtain a composite of alumina ceramic (Al2O3) and sodium beta alumina (NaAl11O17 ), and as starting materials the residue of the ceramic insulator of spark plugs, as a source alumina (Al2O3) powder and unusable sodium bicarbonate (NaHCO3) of fire extinguishers, as a source of sodium oxide (Na2O). The final ceramic product was obtained from a conventional mixture of sodium aluminum oxide in appropriate molar proportions. Sample spark plugs were obtained, discarded by lifetime, specific to a manufacturer, which, after passing through mechanical stress (grinding, magnetic purification, washing, drying and grinding the high energy), which resulted in residue powder with ceramic content of 84.34 % alumina (Al2O3), found by FRX chemical analysis, the phases present and identified by DRX. The dry chemical fire extinguisher, baking soda-based (NaHCO3) with expired, was obtained through direct collection of the waste generated during maintenance. Subjected to heat treatment at 120 °C , the NaHCO3 powder was decomposed in sodium oxide ( Na2O), which, subjected to chemical analysis (FRX) and mineralogical (DRX) revealed a content of 86.62 % sodium oxide (Na2O) . In the following steps the experimental procedure, chemical formulations were made on a molar basis of the starting material (1:9, 1:10 and 1:11 de Na2O/ Al2O3) inclusion of additives, milling parameters, sieve analysis, dilatometry, conformation of specimens, sintering in firing steps at 800 °C , 1000 °C and 1.200 °C with varying stays 30 , 60 and 120 minutes in each of the levels. The characterization of the final product was made by the following physical tests: water absorption, porosity, linear shrinkage, mineralogical analysis by DRX and microstructural analysis by MEV. A higher formation of sodium beta alumina (NaAl11O17), in sintered specimens in levels of 1.200 °C and 120 minutes, despite the prevailing coexistence of alpha phase alumina (Al2O3). From the results obtained opens up prospects for the reuse of waste studied in this work, the potter context and in other technological areas.

Estudo da obtenção de cerâmica composta de alumina e beta alumina sódica utilizando-se resíduo cerâmico de velas de ignição e pó químico de extintores de incêndio

Ceramic materials the alumina base are large industrial applications. They are required for these products, specific characteristics obtained by following strict criteria during the manufacturing process. However, after life, not always these products are reused by a suitable waste management process. In ceramist context, advance research aimed at the reuse of waste aimed at obtaining ceramics and composite materials, with marked reduction of conventional raw materials. Aiming to generate scientific, technological and environmental contribution, this work studied to obtain a composite of alumina ceramic (Al2O3) and sodium beta alumina (NaAl11O17 ), and as starting materials the residue of the ceramic insulator of spark plugs, as a source alumina (Al2O3) powder and unusable sodium bicarbonate (NaHCO3) of fire extinguishers, as a source of sodium oxide (Na2O). The final ceramic product was obtained from a conventional mixture of sodium aluminum oxide in appropriate molar proportions. Sample spark plugs were obtained, discarded by lifetime, specific to a manufacturer, which, after passing through mechanical stress (grinding, magnetic purification, washing, drying and grinding the high energy), which resulted in residue powder with ceramic content of 84.34 % alumina (Al2O3), found by FRX chemical analysis, the phases present and identified by DRX. The dry chemical fire extinguisher, baking soda-based (NaHCO3) with expired, was obtained through direct collection of the waste generated during maintenance. Subjected to heat treatment at 120 °C , the NaHCO3 powder was decomposed in sodium oxide ( Na2O), which, subjected to chemical analysis (FRX) and mineralogical (DRX) revealed a content of 86.62 % sodium oxide (Na2O) . In the following steps the experimental procedure, chemical formulations were made on a molar basis of the starting material (1:9, 1:10 and 1:11 de Na2O/ Al2O3) inclusion of additives, milling parameters, sieve analysis, dilatometry, conformation of specimens, sintering in firing steps at 800 °C , 1000 °C and 1.200 °C with varying stays 30 , 60 and 120 minutes in each of the levels. The characterization of the final product was made by the following physical tests: water absorption, porosity, linear shrinkage, mineralogical analysis by DRX and microstructural analysis by MEV. A higher formation of sodium beta alumina (NaAl11O17), in sintered specimens in levels of 1.200 °C and 120 minutes, despite the prevailing coexistence of alpha phase alumina (Al2O3). From the results obtained opens up prospects for the reuse of waste studied in this work, the potter context and in other technological areas.

Estudo da sinterização e oxidação anódica na produção de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential replacement for be lighter and cheaper than tantalum. They belong to the same table group periodically and thus exhibit several physical and chemical properties similar. Niobium is used in many technologically important applications, and Brazil has the largest reserves, around 96%. These electrolytic capacitors have high specific capacitance, so they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium poder was first characterized by XRD, SEM and laser particle size to then be sieved into particle size 400mesh. The powder was then compacted at pressure of 150MPa and sintered at 1400, 1450 and 1500°C using two sintering time 30 and 60min. Sintering is an important part of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. After sintering the samples were underwent a process of anodic oxidation (anodizing), which created a thin film of niobium pentoxide over the whole surface of the sample, this film is the dielectric capacitor. The anodizing process variables influenced a lot in film formation and consequently the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor and ESR (equivalent series resistance). The sintering has affected the porosity and in turn the specific area of the samples. The capacitor area is directly related to the capacitance, that is, the higher the specific area is the capacitance. Higher sintering temperatures decrease the surface area but eliminate as many impurities. The best results were obtained at a temperature of 1400°C with 60 minutes. The most interesting results were compared with the specific capacitance and ESR for all samples.

Estudo da sinterização e oxidação anódica na produção de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential replacement for be lighter and cheaper than tantalum. They belong to the same table group periodically and thus exhibit several physical and chemical properties similar. Niobium is used in many technologically important applications, and Brazil has the largest reserves, around 96%. These electrolytic capacitors have high specific capacitance, so they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium poder was first characterized by XRD, SEM and laser particle size to then be sieved into particle size 400mesh. The powder was then compacted at pressure of 150MPa and sintered at 1400, 1450 and 1500°C using two sintering time 30 and 60min. Sintering is an important part of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. After sintering the samples were underwent a process of anodic oxidation (anodizing), which created a thin film of niobium pentoxide over the whole surface of the sample, this film is the dielectric capacitor. The anodizing process variables influenced a lot in film formation and consequently the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor and ESR (equivalent series resistance). The sintering has affected the porosity and in turn the specific area of the samples. The capacitor area is directly related to the capacitance, that is, the higher the specific area is the capacitance. Higher sintering temperatures decrease the surface area but eliminate as many impurities. The best results were obtained at a temperature of 1400°C with 60 minutes. The most interesting results were compared with the specific capacitance and ESR for all samples.

Uma proposta de indicadores para o acompanhamento de alunos em projetos de desenvolvimento colaborativo de software com foco no desenvolvimento de habilidades transversais

Soft skills and teamwork practices were identi ed as the main de ciencies of recent graduates in computer courses. This issue led to a realization of a qualitative research aimed at investigating the challenges faced by professors of those courses in conducting, monitoring and assessing collaborative software development projects. Di erent challenges were reported by teachers, including di culties in the assessment of students both in the collective and individual levels. In this context, a quantitative research was conducted with the aim to map soft skill of students to a set of indicators that can be extracted from software repositories using data mining techniques. These indicators are aimed at measuring soft skills, such as teamwork, leadership, problem solving and the pace of communication. Then, a peer assessment approach was applied in a collaborative software development course of the software engineering major at the Federal University of Rio Grande do Norte (UFRN). This research presents a correlation study between the students' soft skills scores and indicators based on mining software repositories. This study contributes: (i) in the presentation of professors' perception of the di culties and opportunities for improving management and monitoring practices in collaborative software development projects; (ii) in investigating relationships between soft skills and activities performed by students using software repositories; (iii) in encouraging the development of soft skills and the use of software repositories among software engineering students; (iv) in contributing to the state of the art of three important areas of software engineering, namely software engineering education, educational data mining and human aspects of software engineering.

Uma proposta de indicadores para o acompanhamento de alunos em projetos de desenvolvimento colaborativo de software com foco no desenvolvimento de habilidades transversais

Soft skills and teamwork practices were identi ed as the main de ciencies of recent graduates in computer courses. This issue led to a realization of a qualitative research aimed at investigating the challenges faced by professors of those courses in conducting, monitoring and assessing collaborative software development projects. Di erent challenges were reported by teachers, including di culties in the assessment of students both in the collective and individual levels. In this context, a quantitative research was conducted with the aim to map soft skill of students to a set of indicators that can be extracted from software repositories using data mining techniques. These indicators are aimed at measuring soft skills, such as teamwork, leadership, problem solving and the pace of communication. Then, a peer assessment approach was applied in a collaborative software development course of the software engineering major at the Federal University of Rio Grande do Norte (UFRN). This research presents a correlation study between the students' soft skills scores and indicators based on mining software repositories. This study contributes: (i) in the presentation of professors' perception of the di culties and opportunities for improving management and monitoring practices in collaborative software development projects; (ii) in investigating relationships between soft skills and activities performed by students using software repositories; (iii) in encouraging the development of soft skills and the use of software repositories among software engineering students; (iv) in contributing to the state of the art of three important areas of software engineering, namely software engineering education, educational data mining and human aspects of software engineering.

Estudo da injeção de água e gás em um reservatório com características do pré-sal brasileiro

The pre-salt province is composed by large amounts of light oil and with good quality, a reality that puts Brazil in a strategic position facing the great demand for energy worldwide. In this province are the largest discoveries in the world in the last ten years; areas as Libra, Franco and Lula field, everyone containing volumes greater than 8 billion recoverable oil barrels. To develop and optimize the production of these fields, a study was done for choosing the improved oil recovery methods. The main motivations were the presence of carbon dioxide (CO2) as a contaminant and the strategic decision of do not discard it, combined with high GOR (gas-oil ratio) of the reservoir fluid. The method should take advantage of the unique abundant resources: seawater and produced gas. This way, the process of matching these resources in the water alterning gas injection (WAG) became a good option. In this master’s dissertation, it was developed a reservoir model with average characteristics of the Brazilian pre-salt, where was applied the improved oil recovery method of water alternating gas. The production of this reservoir was analyzed by parameters as: the first fluid injected in the injection process, position of the injection wells completion, injection water and gas rate and cycle time. The results showed a good performance of the method, with up to 26% of gains in the recovery factor regarding the primary recovery, since the application of water injection and gas, individually, was not able to overcome 10 % of gain. The most influential parameter found in the results was the cycle time, with higher recovery factor values obtained with the use of shorter times.

Estudo de tensoativos na organofilização de argila bentonítica para uso em fluido de perfuração à base de óleo

Due to the great challenges encountered in drilling wells, there is a need to develop fluids with appropriated properties and able to meet all the requirements of drilling operations. The physicochemical and rheological properties must be carefully controlled so that a fluid can exercise all its functions. In perforations sensitive to contact with water and "offshore", it becomes necessary the use of oil based drilling fluids, but the bentonite clay cannot be used without a previous surface modification so that their surfaces become hydrophobic. Lately, the oil companies in Brazil use imported organoclays in the preparation of oil-based drilling fluids. The study aimed to modify a calcium clay to increase the affinity of the same organic phase of oil-based drilling fluids, applying three surfactants (OCS, CTAB and UTM 150) at different concentrations. The results indicated that the surfactants UTM 150 and CTAB showed better results compared to OCS. Considering the type of surfactant and concentration as variables used in the statistical analysis, the results indicated that only the surface tension and concentration of calcium oxide in response to organophilization process showed statistically significant effects. The organophilizated clay has potential for application in oil-based drilling fluids.

Evolução morfotectônica da porção centro-sul da Bacia Paraíba

Recent endogenous processes provide dynamic movements in the lithosphere and generate the varied forms of relief, even in areas of passive continental margins, such as the research area of this work located in northeastern Brazil. The reactivation of Precambrian basement structures, after the breakup between South America and Africa in the Cretaceous played an important role in the evolution of basins, which provided generated forms of relief. These morphodynamic characteristics can be easily observed in marginal basins that exhibit strong evidence fault reactivations. The purpose of this study is to investigate the influence of morphotectonic processes in the landscape structuring of Paraíba Basin. Therefore, we used aeromagnetic, high–resolution images of the Shuttle Radar Topographic Mission–SRTM, structural geological data, deep well data and geological field data. Based on the results of the data was observed that some preexisting structures in the crystalline basement coincide with magnetic and topographic lineaments interpreted as fault reactivation of the Post–Miocene units in the Paraíba Basin. Faults that offset lithostratigraphic units provided evidence that tectonic activity associated with the deposition and erosion in the Paraíba Basin occurred from Cretaceous to the Quaternary. The neotectonic activity that occurred in Paraíba Basin was able to influence the deposition of sedimentary units and landforms. It indicates that the deposition of post–Cretaceous units was influenced by reactivation of Precambrian basement structures in this part of the Brazilian continental margin.

Desenho e implementação de uma plataforma integrada para monitorização e gestão de uma rede de um departamento da UMa

A área da gestão de sistemas e redes tem vindo a alcançar um papel crucial em todas as áreas das Tecnologias de Informação (TI). Com o constante desenvolvimento das redes, em dimensão, inovação tecnológica ou em heterogeneidade, o processo de gestão e monitorização destes sistemas tornou-se cada vez mais exigente e complexo, forçando diversas organizações a investir na implementação ou aquisição de algum software de apoio para os gestores de redes. Com o presente trabalho, pretende-se implementar uma solução integrada para permitir uma gestão preventiva e correctiva dos sistemas da rede informática de um dos departamentos da Universidade da Madeira, denominado por Centro de Competências de Ciências Exactas e da Engenharia (CCCEE). A abordagem a essa solução começa por dar a conhecer alguns dos princípios mais importantes das tradicionais arquitecturas de gestão de redes, e por apresentar um modelo de referência que disponibiliza um conjunto de boas práticas para a gestão de TI. O trabalho continua com o estudo das características da rede informática existente nas instalações do CCCEE, identificando-se não só as reais necessidades na área da gestão e monitorização das TI, como também os principais problemas que a nova solução deveria intervir. A partir destes dados e através de uma análise a um conjunto de ferramentas de gestão e monitorização de redes, selecionou-se a que mais se adequava à realidade do CCCEE. Este trabalho terminou com a monitorização e gestão, contínua e eficiente, das tecnologias de informação do CCCEE, através da implementação da arquitectura de uma solução integrada, de acordo com requisitos e políticas do CCCEE.

Desenho e implementação de uma plataforma integrada para monitorização e gestão de uma rede de um departamento da UMa

A área da gestão de sistemas e redes tem vindo a alcançar um papel crucial em todas as áreas das Tecnologias de Informação (TI). Com o constante desenvolvimento das redes, em dimensão, inovação tecnológica ou em heterogeneidade, o processo de gestão e monitorização destes sistemas tornou-se cada vez mais exigente e complexo, forçando diversas organizações a investir na implementação ou aquisição de algum software de apoio para os gestores de redes. Com o presente trabalho, pretende-se implementar uma solução integrada para permitir uma gestão preventiva e correctiva dos sistemas da rede informática de um dos departamentos da Universidade da Madeira, denominado por Centro de Competências de Ciências Exactas e da Engenharia (CCCEE). A abordagem a essa solução começa por dar a conhecer alguns dos princípios mais importantes das tradicionais arquitecturas de gestão de redes, e por apresentar um modelo de referência que disponibiliza um conjunto de boas práticas para a gestão de TI. O trabalho continua com o estudo das características da rede informática existente nas instalações do CCCEE, identificando-se não só as reais necessidades na área da gestão e monitorização das TI, como também os principais problemas que a nova solução deveria intervir. A partir destes dados e através de uma análise a um conjunto de ferramentas de gestão e monitorização de redes, selecionou-se a que mais se adequava à realidade do CCCEE. Este trabalho terminou com a monitorização e gestão, contínua e eficiente, das tecnologias de informação do CCCEE, através da implementação da arquitectura de uma solução integrada, de acordo com requisitos e políticas do CCCEE.

Building a network Operations Center (NOC) solution

Esta dissertação contextualiza e descreve a actividade prática do quotidiano de um gestor de redes informáticas modernas. Define Network Operations Center (NOC) e a sua importância como provedor de serviços de Internet, e aborda a gestão de redes como alicerce teórico mediante a tomada de decisões que a tarefa de gestão coloca. É com base na complexidade da tarefa de gestão que surge a necessidade e o aparecimento consequente de Plataformas de Gestão. Estas plataformas não só auxiliam na tarefa para a qual foram desenvolvidas como substituem todo um conjunto de ferramentas tradicionais, limitadas para a realidade das infraestruturas de telecomunicações actuais. O estudo do NOC da NOS Madeira enfatiza a problemática que as infra-estruturas de média e grande dimensão comportam para os gestores de redes que lá operam. As limitações da plataforma de gestão em uso referentes à definição e organização de utilizadores, dispositivos e grupos respectivos, conjuntamente com a falta de parametrização em notificações justificam uma solução. Aqui, é feita uma análise e um levantamento de requisitos para a selecção da nova plataforma de gestão seguida da proposta de uma solução integrada para resolução do problema. Esta proposta envolve a definição de uma arquitectura, o desenho e a implementação de software próprios para um sistema particular ao qual designamos: ZenDash.

Building a network Operations Center (NOC) solution

Esta dissertação contextualiza e descreve a actividade prática do quotidiano de um gestor de redes informáticas modernas. Define Network Operations Center (NOC) e a sua importância como provedor de serviços de Internet, e aborda a gestão de redes como alicerce teórico mediante a tomada de decisões que a tarefa de gestão coloca. É com base na complexidade da tarefa de gestão que surge a necessidade e o aparecimento consequente de Plataformas de Gestão. Estas plataformas não só auxiliam na tarefa para a qual foram desenvolvidas como substituem todo um conjunto de ferramentas tradicionais, limitadas para a realidade das infraestruturas de telecomunicações actuais. O estudo do NOC da NOS Madeira enfatiza a problemática que as infra-estruturas de média e grande dimensão comportam para os gestores de redes que lá operam. As limitações da plataforma de gestão em uso referentes à definição e organização de utilizadores, dispositivos e grupos respectivos, conjuntamente com a falta de parametrização em notificações justificam uma solução. Aqui, é feita uma análise e um levantamento de requisitos para a selecção da nova plataforma de gestão seguida da proposta de uma solução integrada para resolução do problema. Esta proposta envolve a definição de uma arquitectura, o desenho e a implementação de software próprios para um sistema particular ao qual designamos: ZenDash.

Enrichment of bioactive compounds in microalgae for aquaculture

Microalgae are promising microorganisms for the production of food and fine chemicals. Several species of microalgae are used in aquaculture with the purpose of transfer bioactive compounds up to the aquatic food chain. The main objective of this project was to develop a stress–inducement strategy in order to enhance the biochemical productivity of Nannochloropsis gaditana, Rhodomonas marina and Isochrysis sp. for aquaculture purposes having in account their growth and organizational differences. In this regard, two experiments were design: the first one consisted on the alteration of overall nutrient availabilities in growth medium; and the second one comprised changes in nitrogen and sulfur concentrations maintaining the concentrations of the other nutrients present in a commercial growth medium (Nutribloom plus), which is frequently used in aquaculture. Microalgae dried biomass was characterized biochemically and elemental analysis was also performed for all samples. In first experimental design: linear trends between nutrient availability in growth media and microalgae protein content were obtained; optimum productivities of eicosapentaenoic (EPA) and docosahexaenoic acids (DHA) were attained for both R. marina and N. gaditana in growth media enriched with 1000 L L-1 of nutrient solution whereas for Isochrysis sp. the double of Nutribloom plus was needed; the decrease of glucans and total monosaccharides with nutrient availability for R. marina and Isochrysis sp. showed the occurrence of a possible depletion of carbohydrates towards lipids and proteins biosynthesis. Second experimental desing: N. gaditana exhibited the highest variation in their biochemical composition against the applied perturbation; variations observed for microalgae in their biochemical composition were reflected in their elemental stoichiometry; in N. gaditana the highest nitrogen concentrations lead to overall maximum productivities of the biochemical parameters. The results of the present work show two stress-inducement strategies for microalgae that may constitute a base for further investigations on their biochemical enhancement.

De touch: extending service channels in an airport through touch technologies

This project aimed to create a communication and interaction channel between Madeira Airport and its passengers. We used the pre-existent touch enabled screens at the terminal since their potential was not being utilised to their full capacity. To achieve our goal, we have followed an agile strategy to create a testable prototype and take advantages of its results. The developed prototype is based on a plugin architecture turning it into a maintainable and highly customisable system. The collected usage data suggests that we have achieved the initially defined goals. There is no doubt that this new interaction channel is an improvement regarding the provided services and, supported by the usage data, there is an opportunity to explore additional developments to the channel.